Spectral shaping of femtosecond pulses with a prism-waveguide coupler

We report a novel technique for spectral shaping of femtosecond pulses employing a prism-waveguide coupler (PWC). It is demonstrated that the PWC is capable of producing a frequency-dependent loss with greater attenuation at the peak of the spectrum profile of femtosecond pulses than in the wings, which is especially useful for compensation for gain narrowing in most chirped-pulse amplification laser systems.

Optical microwave generation using two parallel DFB lasers integrated with Y-branch waveguide coupler

A new device of two parallel distributed feedback (DFB) lasers integrated monolithically with Y-branch waveguide coupler was fabricated by means of quantum well intermixing. Optical microwave signal was generated in the Y-branch waveguide coupler through frequency beating of the two laser modes coming from two DFB laser in parallel, which had a small difference in frequency. Continuous rapid tuning of optical microwave signal from 13 to 42 GHz were realized by adjusting independently the driving currents injected into the two DFB lasers.

A High-Efficiency Fiber-to-Waveguide Coupler with Low Polarization Dependence Using a Diluted Waveguide in InP Substrate with a 1.55μm Wavelength

We propose a fiber-to-waveguide coupler for side-illuminated p-i-n photodiodes to obtain high responsivity and low polarization dependence that is grown on InP substrate and is suitable for surface hybrid integration in low cost modules. The fiber-to-waveguide coupler is based on a diluted waveguide,which is composed of ten periods of undoped 120nm InP/80nm InGaAsP （1.05μm bandgap） multiple layers. Using the semi-vectorial three dimensional beam propagation method （BPM） with the central difference scheme,the coupling efficiency of fiber-to-waveguide under different conditions is simulated and studied,and the optimized conditions for fiber-to-waveguide coupling are obtained. For TE-like and TM-like modes,the calculated maximum coupling efficiency is higher than 94% and 92% ,respectively. The calculated polarization dependence is less than 0. ldB,showing good polarization independence.

High efficiency fiber to waveguide optical coupler in silicon-on-insulator-based slot waveguides - art. no. 68310R

We propose a novel optical fiber-to-waveguide coupler for integrated optical circuits. The proper materials and structural parameters of the coupler, which is based on a slot waveguide, are carefully analyzed using a full-vectorial three dimensional mode solver. Because the effective refractive index of the mode in a silicon-on-insulator-based slot waveguide can be extremely close to that of the fiber, a highly efficient fiber-to-waveguide coupling application can be realized. For a TE-like mode, the calculated minimum mismatch loss is about 1.8dB at 1550nm, and the mode conversion loss can be less than 0.5dB. The discussion of the present state-of-the-art is also involved. The proposed coupler can be used in chip-to-chip communication.

Characteristics of 980/1550 nm WDM coupler based on planar curved waveguides

A wavelength division multiplexer (WDM) for 980/1550 nm based on planar curved waveguide coupler (CWC) is proposed. Compared with conventional parallel straight waveguide coupler (SWC), this structure has more flexibility with two variable parameters of bending radius R and minimum edge-to-edge spacing do, which are the two main parameters for the splitting ratio of coupler and decrease the complexity of device design and fabrication. Based on coupled mode theory (CMT) and waveguide theory, R and do of the WDM CWC are designed to be R = 13.28 m and d(0) = 4.39 mu m. The contrast ratio (CR) and insertion loss (IL) for 980 and 1550 nm are CR1 = 24.62 dB, CR2 = 24.56 dB and IL1 = 0.014 dB, IL2 = 0.015 dB, respectively. The 3D beam propagation method (BPM) is used to verify the validity of the design result. The influence of R and d(0) variations on the device performance is analyzed. For CR > 20 dB, the variation ranges of R and d(0) should be within -0.10 to +0.44 m and -0.05 to + 0.02 mu m, respectively. (c) 2006 Elsevier GmbH. All rights reserved.

平面弯曲波导耦合器的特性分析

根据耦合模理论和弯曲波导耦合器的结构特点,对平面弯曲波导耦合器的特性进行了分析,结果表明弯曲波导耦合器的弯曲半径和最小间距两个可调变量,增加了波导器件设计的灵活性;同时由于等效耦合长度的调制作用使得弯曲波导耦合器在波分复用/解复用中比平行直波导耦合器具有更大的复用带宽;分析了弯曲半径和最小间距对弯曲波导耦合器复用带宽的影响,为实际波导器件的设计制作提供了一定的理论依据.

Prism coupling of ultrashort light pulses into waveguides

We discuss coupling of ultrashort light pulses into waveguides by use of a prism waveguide coupler configuration. Theoretical analysis indicates that an extra loss induced by the short coherence times of ultrashort pulses, which has a strong effect on the reflected light and the optimum coupling condition, appears in the waveguide. Numerical simulations show that the reflectance strongly depends on the coherence times of ultrashort pulses. A method for realizing optimum coupling by compensating for the extra loss is proposed as well in this paper. A preliminary experiment of employing ultrashort pulses with different coherence times was carried out, and good agreement between theory and experiment was obtained. (c) 2006 Optical Society of America.

Optical microwave generation based on DFB lasers

A new device of two parallel distributed feedback ( DFB) laser integrated monolithically with Y-branch waveguide coupler was fabricated by means of quantum well intermixing. Optical microwave signal was generated in the Y-branch waveguide coupler through frequency beating of the two laser modes coming from two DFB lasers in parallel, which had a small difference in frequency. Continuous rapidly tunable optical microwave signals from 13 GHz to 42 GHz were realized by adjusting independently the driving currents injected into the two DFB lasers.

Optical matching layer structures in evanescent coupling photodiodes at a wavelength of 1.55 mu m: physics, design and simulation

We have studied the optical matching layers (OMLs) and external quantum efficiency in the evanescent coupling photodiodes (ECPDs) integrating a diluted waveguide as a fibre-to-waveguide coupler, by using the semi-vectorial beam propagation method (BPM). The physical basis of OML has been identified, thereby a general designing rule of OML is developed in such a kind of photodiode. In addition, the external quantum efficiency and the polarization sensitivity versus the absorption and coupling length are analysed. With an optical matching layer, the absorption medium with a length of 30 mu m could absorb 90% of the incident light at 1.55 mu m wavelength, thus the total absorption increases more than 7 times over that of the photodiode without any optical matching layer.

Tunneling transmission in two quantum wires coupled by a magnetically defined barrier

A numerical analysis of an electron waveguide coupler based on two quantum wires coupled by a magnetically defined barrier is presented with the use of the scattering-matrix method. For different geometry parameters and magnetic fields, tunneling transmission spectrum is obtained as a function of the electron energy. Different from that of conventional electron waveguide couplers, the transmission spectrum of the magnetically coupled quantum wires does not have the symmetry with regard to those geometrically symmetrical ports, It was found that the magnetic field in the coupling region drastically enhances the coupling between the two quantum wires for one specific input port while it weakens the coupling for the other input port. The results can be well understood by the formation of the edge states in the magnetically defined barrier region. Thus, whether these edge states couple or decouple to the electronic propagation modes in the two quantum wires, strongly depend on the relative moving directions of electrons in the propagating mode in the input port and the edge states in the magnetic region. This leads to a big difference in transmission coefficients between two quantum wires when injecting electrons via different input ports. Two important coupler specifications, the directivity and uniformity, are calculated which show that the system we considered behaves as a good quantum directional coupler. (C) 1997 American Institute of Physics.

High efficiency and broad bandwidth grating coupler between nanophotonic waveguide and fibre

A high efficiency and broad bandwidth grating coupler between a silicon-on-insulator (SOI) nanophotonic waveguide and fibre is designed and fabricated. Coupling efficiencies of 46% and 25% at a wavelength of 1.55 mu m are achieved by simulation and experiment, respectively. An optical 3 dB bandwidth of 45 nm from 1530 nm to 1575 nm is also obtained in experiment. Numerical calculation shows that a tolerance to fabrication error of 10 nm in etch depth is achievable. The measurement results indicate that the alignment error of +/-2 mu m results in less than 1 dB additional coupling loss.

Novel triplexing-filter design using silica-based direction coupler and an arrayed waveguide grating

A new triplexing filter based on a silica direction coupler and an arrayed waveguide grating is presented. Using a combination of a direction coupler and an arrayed waveguide grating, a 1310-nm channel is multiplexed and 1490- and 1550-nm channels are demultiplexed for fiber-to-the-home. The direction coupler is used to coarsely separate the 1310-nm channel from the 1490- and 1550-nm channels. Subsequently, an arrayed waveguide grating is used to demultiplex the 1490- from 1550-nm channel. The simulated spectra show the 1-dB bandwidth of 110 nm for the 1310-nm channel and 20 and 20.5 nm for the 1490- and 1550-nm channels. The insertion loss is only 0.15 dB for 1310 nm and 5 dB for 1490 and 1550 nm. The crosstalk between the 1490- and 1550-nm channels was less than -35 dB. (C) 2009 Society of Photo-Optical Instrumentation Engineers. [DOI 10.1117/1.3065508]

A photonic wire-based directional coupler based on SOI

A photonic wire-based directional coupler based on SOI was fabricated by e-beam lithography (EBL) and the inductively coupled plasma (ICP) etching method. The size of the sub-micron waveguide is 0.34 mu m x 0.34 mu m, and the length in the coupling region and the separation between the two parallel waveguides are 410 and 0.8 mu m, respectively. The measurement results are in good agreement with the results simulated by 3D finite-difference time-domain method. The transmission power from two output ports changed reciprocally with about 23 nm wavelength spacing between the coupled and direct ports. The extinction ratio of the device was between 5 and 10 dB, and the insertion loss of the device in the wavelength range 1520-1610 nm was between 22 and 24 dB, which included an about 18.4 +/- 0.4 dB coupling loss between the taper fibers and the polished sides of the device. (c) 2008 Elsevier B.V. All rights reserved.

Multimode interference 3-dB coupler in silicon-on-insulator based on silicon rib waveguides with trapezoidal cross section

A 3-dB multimode interference optical coupler based on rib waveguides with trapezoidal cross section was designed and fabricated on silicon-on-insulator wafer. Potassium hydroxide (KOH) anisotropic chemical etching of silicon was used to fabricate the waveguides to obtain smooth interface. A modified finite-difference beam propagation method was used to simulate the multimode rib waveguide with slope interfaces. The rms roughness of etching interface is as small as 1.49 nm. The propagation loss of the waveguide is 1.3 dB/cm at wavelength of 1.55 mum. The fabricated 3-dB coupler has a good uniformity of 0.2 dB.

Research progresses of SOI optical waveguide devices and integrated optical switch matrix

SOI (silicon-on-insulator) is a new material with a lot of important performances such as large index difference, low transmission loss. Fabrication processes for SOI based optoelectronic devices are compatible with conventional IC processes. Having the potential of OEIC monolithic integration, SOI based optoelectronic devices have shown many good characteristics and become more and more attractive recently. In this paper, the recent progresses of SOI waveguide devices in our research group are presented. By highly effective numerical simulation, the single mode conditions for SOI rib waveguides with rectangular and trapezoidal cross-section were accurately investigated. Using both chemical anisotropic wet etching and plasma dry etching techniques, SOI single mode rib waveguide, MMI coupler, VOA (variable optical attenuator), 2X2 thermal-optical switch were successfully designed and fabricated. Based on these, 4X4 and 8X8 SOI optical waveguide integrated switch matrixes are demonstrated for the first time.