241 resultados para Tin compounds.
Resumo:
The relationship between the chemical displacement of the binding energy and the different chemical environment for 12 organic tin compounds was studied by means of X-ray photoelectron spectronscopy. The different substituents in the compounds have influence on the tin outer electron and Sn-O bond, which was discussed by Xray photoelectron spectroscopy and mass spectrum.
Resumo:
The surface tension of molten tin has been determined by the sessile drop method at The surface tension of molten tin has been determined by the sessile drop method at temperatures ranging from 523 to 1033 K and in the oxygen partial pressure (P-O2) range from 2.85 x 10(-19) to 8.56 x 10(-6) MPa, and its dependence on temperature and oxygen partial pressure has been analyzed. At P-O2 = 2.85 x 10(-19) and 1.06 x 10(-15) MPa, the surface tension decreases linearly with the increase of temperature and its temperature coefficients are -0.151 and -0.094 mNm(-1) K-1, respectively. However, at high P-O2 (3.17 x 10(-10), 8.56 x 10(-6) MPa), the surface tension increases with the temperature near the melting point (505 K) and decreases above 723 K. The surface tension decrease with increasing P-O2 is much larger near the melting point than at temperatures above 823 K. The contact angle between the molten tin and the alumina substrate is 158-173degrees, and the wettability is poor.
Resumo:
Orthogonal designs are used to investigate the main factors when doing experiments in which pulse bias is superimposed on d.c. bias during cathodic are deposition of TiN. Pulse peak, duty cycle, frequency, direct voltage, are current and pressure all are investigated when coating TiN on HSS substrates. Roughness, surface micrograph, microhardness and thickness are tested. By analysis of variance, it is shown that pressure and frequency are the main factors. R-a and droplet density of the film with (d.c. + pulse) bias decrease. A simple explanation for the result is suggested.
Resumo:
Nanoindentation and nanoscratch tests were performed for titanium nitride (TiN) coatings on different tool steel substrates to investigate the indentation/scratch induced deformation behavior of the coatings and the adhesion of the coating–substrate interfaces and their tribological property. In this work, TiN coatings with a thickness of about 500 nm were grown on GT35, 9Cr18 and 40CrNiMo steels using vacuum magnetic-filtering arc plasma deposition. In the nanoindentation tests, the hardness and modulus curves for TiN/GT35 reduced the slowest around the film thickness 500 nm with the increase of indentation depth, followed by TiN/9Cr18 and TiN/40CrNiMo. Improving adhesion properties of coating and substrate can decrease the differences of internal stress field. The scratch tests showed that the scratch response was controlled by plastic deformation in the substrate. The substrate plays an important role in determining the mechanical properties and wear resistance of such coatings. TiN/GT35 exhibited the best load-carrying capacity and scratch/wear resistance. As a consequence, GT35 is the best substrate for TiN coatings of the substrate materials tested.
Resumo:
Numerical simulations were conducted to study thermocapillary flows in short half-zone liquid bridges of molten tin with Prandtl number Pr = 0.009, under ramped temperature difference. The spatio-temporal structures in the thermocapillary flows in short half-zone liquid bridges with aspect ratios As = 0.6, 0.8, and 1.0 were investigated. The first critical Marangoni numbers were compared with those predicted by linear stability analyses (LSA). The second critical Marangoni numbers for As = 0.6 and 0.8 were found to be larger than that for As = 1.0. The time evolutions of the thermocapillary flows exhibited unusual features such as a change in the azimuthal wave number during the three-dimensional stationary (non-oscillating) flow regime, a change in the oscillation mode during the three-dimensional oscillatory flow regime, and the decreasing and then increasing of amplitudes in a single oscillation mode. The effects of the ramping rate of the temperature difference on the flow modes and critical conditions were studied as well. In this paper, the experimental observability of the critical conditions was also discussed. (C) 2008 Elsevier Inc. All rights reserved.
Resumo:
用过滤电弧技术在高速钢表面沉积了TiN/TiCrN/CrN/CrTiN多层膜 ,用扫描电镜 (SEM )观察了截面和断口形貌及划痕后的形貌。使用俄歇电子谱仪进行剥层成分分析 ,用纳米压痕仪测试了多层膜和单层膜的显微硬度和弹性模量。结果表明 ,在调制周期大于 10 0nm时 ,多层膜的显微硬度符合Hall Petch关系 ,在 80nm时 ,则脱离线性关系。划痕法测试多层膜的结合力达到 80N。
Resumo:
用过滤电弧离子镀(FAMIP)技术在高速钢基体上沉积了TiN、ZrN单层薄膜和TiN/CrN多层纳米薄膜。利用扫描电子显微镜(SEM)观察了薄膜及其划痕的表面形貌;用X射线衍射仪(XRD)分析了薄膜的相组成,结合显微探针仪、划痕试验机、金相显微镜和钻床,研究了金属陶瓷单层和多层纳米薄膜的性能并进行比较。研究结果表明:3种薄膜的临界载荷值均大于80N,多层纳米薄膜的耐磨性明显优于2种单层薄膜。
Resumo:
在电弧离子镀技术中使用脉冲偏压电源是近年来发展起来的一项新技术。研究表明,在薄膜沉积过程中,以直流偏压为基础,迭加一个高脉冲电压,有助于改善薄膜的性能,并且能够在较低的沉积温度下获得结合力较强、内应力较小、表面光洁度也比较好的薄膜。通过正交设计和方差分析,本文首次研究了在电弧离子镀技术中使用脉冲偏压电源, 在高速钢和不锈钢基体上沉积TiN和CrN的过程中,对薄膜的表面粗糙度、表面形貌、结合力、显微硬度、沉积速率等性能的影响,发现:(1) 在考虑气氛、弧电流和脉冲电源的各种参数的情况下,气氛和频率是影响薄膜性能的主要因素;(2)在气氛、弧电流不变的条件下,脉冲电源的频率和占空比是影响薄膜粗糙度的主要因素;(3)在比较了直流偏压和脉冲偏压的实验结果之后,认为利用直流迭加脉冲的偏压方式,经过优化参数,能够比较显著地 降低薄膜的表面粗糙度,提高沉积速率。
Resumo:
Transparent and translucent SnO2 aerogels with high specific surface area (>300m(2)/g) have been prepared by sol-gel process using tetra(n-butoxy)tin(IV) as a starting compound, and supercritical drying technique for solvent extraction. Light scattering measurements reveal that the polymeric cluster size distribution in sol system is gradually broadened during sol-gel transition. SEM images show that the aerogels are made up of the cottonlike oxide agglomerates with a large number of Pores. TEM images show that these aerogels seem to be self-similar at different magnifications. Their pore size distribution is pretty wide ranging, from mesopore to macropore especially for that of translucent aerogel. (C) 2004 Elsevier B.V. All rights reserved.