30 resultados para SQUID LOLIGO PEALII
Resumo:
G-M制冷机是回热式的小型低温制冷机,它利用绝热放气膨胀原理(又称为西蒙膨胀法)获得低温,具有振动小、运行稳定、寿命长、操作方便等特点,在对效率、重量、尺寸等没有太高要求的场合应用非常广泛。在八十年代末,G-M制冷机已经突破了液氦温度,非常适合在液氦温区为超导器件或电子元件提供冷量,在低温真空泵、MRI超导磁体冷却系统、SQUID再冷凝系统等方面有良好的应用前景,推广其应用已属当务之急。本文围绕着探索氦温区G-M制冷机工作机理、提高低温蓄冷器性能及新型结构G-M制冷机的研制等方面,进行了系统地理论分析和纳归纳,以及初步地实验研究:一. 首次比较完善地建立了液氦温区G-M型制冷机整机数值模拟方法,数值模拟方法给出了制冷机内工质参数瞬态分布及动态变化曲线,为分析制冷机独特的循环特性提供了直观的依据,为探讨运行及结构参数对制冷性能的影响机理提供了强有力的工具。模型中考虑了制冷机中的阻力、实际进排气角、物性变化及蓄冷器内空隙率的存在等多种实际因素:解决了一、二级耦合及部件交界处物性变化不连续对计算影响等问题;采取网格非均匀化、牛顿迭代法以及负反馈原理等措施,提高了计算精度和收敛性。在微机上成功地模拟了液氦温区G-M制冷机的工作过程,程序采用模块化编程,具有一定通用性。二. 运用液氦温区整套机数值模拟方法,计算了制冷机内工质参数(氦流温度、压力、流速等)周期性变化和空间分布,采用一级蓄冷器与低温蓄冷器工作特性对比法,从整机内工质参数动态变化规律分析的角度,验证了液氦温区G-M制冷机工质氦的循环主要分为两部分:常规循环、低温循环。并详细地讨论了运行参数(频率、工作压力)及一级制冷机结构参数对整机内工数动态变化的影响规律以及制冷机性能的影响机理。三. 首次建立了较完善的液氦温区多层混合填料型低温蓄冷器的数值模拟方法,运用数值模拟方法,首次详细地研究了常用填料的不同组合、一定组合下填料比例以及蓄冷器结构对制冷机性能的影响机理,提出了不同填料的最佳节组合及一定组合下填料最佳比例的确定和低温蓄冷器结构和填料优化的原则,为合理有效地设计高性能液氦温区低温蓄冷器提供了依据。四. 提出并设计、加工了一种新型结构的液氦温区双级G-M型制冷机,该机结构在国内外属于首创。其具有以下主要结构特点:一、二级分别独立驱动;一、二级之间通过热桥连接;二级蓄冷器外置于汽缸等。同时建立了新型结构液氦温区双级G-M型制冷机实验系统,为今后整机性能和内部动态过程的研究奠定了基础。五. 新型结构双级G-M型制冷机二级单机动转频率为0.6Hz时,制冷温度为13.6K,且在20K时有4.4W的制冷量;制冷机已达到液氦温区,f = 0.4Hz时,最低温度为4.6K;f = 1Hz,制冷温度为10K时,制冷量大于6W,上述结果目前均未见有文献报道。在新型G-M制冷机上,初步进行了低温蓄冷器性能测试实验及运行参数对制冷机性能影响的实验研究。
Resumo:
The objectives of the study were to investigate the effect of a feeding stimulant on feeding adaptation of gibel carp (Carassius auratus gibelio Bloch) fed diets with replacement of fish meal by meat and bone meal (MBM), and whether or not the juvenile gibel carp could adapt to higher MBM level in the diet. Juvenile and adult gibel carp were tested. Two and one replacement levels were used for juvenile and adult fish respectively. Each group of diets was set as two types with or without a unique rare earth oxide: Y2O3, Yb2O3, La2O3, Sm2O3, Nd2O3 or Gd2O3 (only the first four rare earth oxides were used in adult diets) for four adaptation periods of 3, 7, 14 and 28 days respectively. After mixing, an equal mixture of all six diets for juvenile or four diets for adult was offered in excess for 2 days. During the last 2 days of each experiment, no feed was offered and faeces from each tank were collected. Feeding preference was expressed as relative feed intake of each diet, which was estimated based on the relative concentration of each marker in the faeces. Given some adaptation period, such as 3-28 days, the effects of MBM and squid extract inclusion on the preference to each diet were reduced. After 28 days adaptation, the preferences between groups were not significantly different.
Resumo:
The objectives of this work were to study the effects of several feeding stimulants on gibel carp fed diets with or without replacement of fish meal by meat and bone meal (MBM). The feeding stimulants tested were betaine, glycine, L-lysine, L-methionine, L-phenylalanine, and a commercial squid extract. Three inclusion levels were tested for each stimulant (0.18, 0.5%, and 1% for betaine and 0.1, 0.25 and 0.5% for the other stimulants). Two basal diets (40% crude protein) were used. one with 26% fish meal (FM), and the other with 21% fish meal and 6% MBM, Betaine at 0.1% in the fish meal group and at 0.5% in the meat and bone meal group was used in all experiments for comparison among stimulants. In the experiment on each stimulant, six tanks of fish were equally divided into two groups, one fed the FM diet, and the other fed the MBM diet. After 7 days' adaptation to the basal diet, in which the fish were fed to satiation twice a day, the fish were fed for another 7 days an equal mixture of diets containing varying levels of stimulants. Each diet contained a unique rare earth oxide as inert marker (Y2O3, Yb2O3, La2O3, Sm2O3 or Nd2O3). During the last 3 days of the experiment, faeces from each tank were collected. Preference for each diet was estimated based on the relative concentration of each marker in the faeces. Gibel carp fed the FM diet had higher intake than those fed the MBM diet, but the difference was significant only in the experiments on betaine, glycine and L-methionine. None of the feeding stimulants tested showed feeding enhancing effects in FM diets. All feeding stimulants showed feeding enhancing effects in MBM diets. and the optimum inclusion level was 0.5% for betaine, 0.1% for glycine, 0.25% for L-lysine, 0.1% for L-methionine. 0.25% For L-phenylalanine. and 0.1% for squid extract. The squid extract had the strongest stimulating effect among all the stimulants tested. (C) 2001 Elsevier Science B.V. All rights reserved.
Resumo:
The structural and magnetic properties of Cu+ ions-implanted GaN films have been reported. Eighty kilo-electron-volt Cu+ ions were implanted into n-type GaN film at room temperature with fluences ranging from 1 x 10(16) to 8 x 10(16) cm(-2) and subsequently annealed at 800 degrees C for 1 h in N-2 ambient. PIXE was employed to determine the Cu-implanted content. The magnetic property was measured by the Quantum Design MPMS SQUID magnetometer. No secondary phases or clusters were detected within the sensitivity of XRD. Raman spectrum measurement showed that the Cu ions incorporated into the crystal lattice positions of GaN through substitution of Ga atoms. Apparent ferromagnetic hysteresis loops measured at 10 K were presented. The experimental result showed that the ferromagnetic signal strongly increased with Cu-implanted fluence from 1 x 10(16) to 8 x 10(16) cm(-2).
Resumo:
We have systematically investigated the magnetic properties of Si-doped (Ga,Mn)As films. When the Si content is low, both Curie temperature (T-C) and carrier density (p) decrease compared with undoped (Ga,Mn)As, whereas a monotonic increase of T-C and p is observed with further increase in the doping content of Si. We discuss the possible mechanism for the changes obtained by different Si doping contents and attribute the results to a competition between the existence of Si-Ga (Si substitutes for Ga site) that acts as a donor and Si-I (Si interstitials) which is in favor of the improvement of ferromagnetism. (C) 2008 Elsevier B.V. All rights reserved.
Resumo:
Diluted magnetic nonpolar GaN:Mn films have been fabricated by implanting Mn ions into unintentionally doped nonpolar a-plane (1 1 (2) over bar 0) GaN films with a subsequent rapid thermal annealing (RTA) process. The structure, morphology and magnetic characteristics of the samples were investigated by means of high-resolution x-ray diffraction (XRD), atomic force microscopy (AFM) and a superconducting quantum interference device (SQUID), respectively. The XRD analysis shows that the RTA process can effectively recover the crystal deterioration caused by the implantation process and that there is no obvious change in the lattice parameter for the as-annealed sample. The SQUID result indicates that the as-annealed sample shows ferromagnetic properties and magnetic anisotropy at room temperature.
Resumo:
Diluted magnetic nonpolar GaN Mn films have been fabricated by implanting Mn ions into nonpolar aplane (1 1 (2) over bar 0) p-type GaN films and a subsequent rapid thermal annealing process. The ferromagnetism properties of the films were studied by means of superconducting quantum interference device (SQUID). Clearly in-plane magnetic anisotropy characteristics of the sample at 10 K were revealed with the direction of the applied magnetic field rotating along the in-plane [0 0 0 1]-axis. Moreover, obvious ferromagnetic properties of the sample up to 350 K were detected by means of the temperature-dependent SQUID. (C) 2009 Elsevier B.V. All rights reserved.
Resumo:
Ferromagnetic properties of Mn-implanted wurtzite AlxIn1-xN/GaN thin films grown by metal organic chemical vapor deposition (MOCVD) were observed using a quantum design superconducting quantum interference device (SQUID) magnetometer. Hysteresis behavior with a reasonably high saturation magnetic moment at room temperature for all the samples was noted, Two optical thresholds were observed at 1.58 and 2.64 eV, which are attributed to internal transition (E-5 -> T-5(2)) of Mn3+ (d(4)) and hole emission from the neutral Mn acceptor level to the valence band respectively. Bound magnetic polaron formation is considered to be the origin of ferromagnetism in our samples. (c) 2009 The Japan Society of Applied Physics
Resumo:
(In, Cr)As ferromagnetic semiconductor quantum dots (QDs) were grown by molecular beam epitaxy on GaAs (001) substrates. The growth temperature effects on structure and magnetism of the QDs were investigated systematically. The Cr(2+)3d(4) states and quantum confined effect are assumed to play an important role in the room-temperature ferromagnetism of (In, Cr)As QDs. (C) 2009 Elsevier B.V. All rights reserved.
Resumo:
We have fabricated a set of samples of zincblende Mn-rich Mn(Ga)As clusters embedded in GaAs matrices by annealing (Ga,Mn)As films with different nominal Mn content at 650 degrees C. For the samples with Mn content no more than 4.5%, the Curie temperature reaches nearly 360 K. However, when Mn content is higher than 5.4%, the samples exhibit a spin-glass-like behavior. We suggest that these different magnetic properties are caused by the competing result of dipolar and Ruderman-Kittel-Kasuya-Yosida interaction among clusters. The low-temperature spin dynamic behavior, especially the relaxation effect, shows the extreme creeping effect which is reflected by the time constant tau of similar to 10(11) s at 10 K. We explain this phenomenon by the hierarchical model based on the mean-field approach. We also explain the memory effect by the relationship between the correlation function and the susceptibility.
Resumo:
We study the structure, optical and magnetic characteristics of self-assembled (In,Cr) As diluted magnetic semiconductor quantum dots as a function of the As-4 flux. Increasing the surface energy by increasing the As4 pressure leads to a smaller number of larger dots for a higher As-4 flux. The remanent magnetization measured at 5K also increases with increasing As-4 flux, which is attributed to the enhancement of the effective Cr content due to the As-4-rich condition. We explore the possibility of tailoring magnetism by controlling the As-4/In flux ratio without changing the Cr concentration. Furthermore, extremely low-density QDs have also been successfully grown. Copyright (C) EPLA, 2008
Resumo:
Nonpolar GaN Mn films have been fabricated by implanting Mn-ion into nonpolar a-plane (MO) GaN films at room temperature. The influence of implantation energy on the Structural, morphological and magnetic characteristics of samples have been investigated by means of stopping and range of ions in matter (SRIM) Simulation software, high-resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM), and superconducting quantum interference device (SQUID). According to the SQUID analysis, obvious room temperature ferromagnetic properties of samples were detected. Moreover, the implantation energy has little impact on the ferromagnetic properties of samples. The XRD and AFM analyses show that the structural and morphological characteristics of samples were severely deteriorated with the increase of implantation energy. (C) 2008 Elsevier B.V. All rights reserved.
Resumo:
Diluted magnetic nonpolar GaN:Cu films have been fabricated by implanting Cu ions into unintentionally doped nonpolar a-plane(1 1 (2) over bar 0) GaN films and a subsequent thermal annealing process. The structural, morphological and magnetic characteristics of the samples have been investigated by means of high-resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM), and superconducting quantum interference device (SQUID). The sample shows a clear ferromagnetism behavior at room temperature. It is significantly shown that with a Cu concentration as low as 0.75% the sample exhibits a saturation magnetization about 0.65 mu(B)/Cu atom. Moreover, the possible origin of the ferromagnetism for the sample was also discussed briefly. (C) 2009 Elsevier B. V. All rights reserved.