2.1 GHz MOS mixer linearisation approach for IIP2 enhancement using multiple factor compensation

An integrated downconversion CMOS mixer incorporating a comprehensive compensation scheme is presented which aims to minimise second-order intermodulation distortion (IMD2). Unlike previously reported IMD2 calibration schemes which tune only one nonlinear factor at a time, the presented solution allows simultaneous adjustment of several different factors thus achieving a better compensation. The mixer has been implemented in UMC 0.18 μm CMOS to verify the proposed scheme and for comparison with alternative compensation methods. Measurements show that the solution described can improve the input intercept point (IIP2) by over 20 dB while maintaining good amplification and noise performance. IMD2 calibration results are presented and show useful advantages over other approaches. To the best of the authors' knowledge, this scheme for IMD2 calibration has not been previously reported. © The Institution of Engineering and Technology 2013.

High photoluminescence quantum efficiency InGaN multiple quantum well structures emitting at 380 nm

In this paper we report the design of high room temperature photoluminescence internal efficiency InGaN-based quantum well structures emitting in the near ultraviolet at 380 nm. To counter the effects of nonradiative recombination the quantum wells were designed to have a large indium fraction, high barriers, and a small quantum well thickness. To minimize the interwell and interbarrier thickness fluctuations we used Al0.2In0.005Ga0.795N barriers, where the inclusion of the small fraction of indium was found to lead to fewer structural defects and a reduction in the layer thickness fluctuations. This approach has led us to achieve, for an In0.08Ga0.92N/Al0.2In0.005Ga0.795N multiple quantum well structure with a well width of 1.5 nm, a photoluminescence internal efficiency of 67% for peak emission at 382 nm at room temperature. (c) 2007 American Institute of Physics.

Multiple single unit recording in the cortex of monkeys using independently moveable microelectrodes.

Simultaneous recording from multiple single neurones presents many technical difficulties. However, obtaining such data has many advantages, which make it highly worthwhile to overcome the technical problems. This report describes methods which we have developed to permit recordings in awake behaving monkeys using the 'Eckhorn' 16 electrode microdrive. Structural magnetic resonance images are collected to guide electrode placement. Head fixation is achieved using a specially designed headpiece, modified for the multiple electrode approach, and access to the cortex is provided via a novel recording chamber. Growth of scar tissue over the exposed dura mater is reduced using an anti-mitotic compound. Control of the microdrive is achieved by a computerised system which permits several experimenters to move different electrodes simultaneously, considerably reducing the load on an individual operator. Neurones are identified as pyramidal tract neurones by antidromic stimulation through chronically implanted electrodes; stimulus control is integrated into the computerised system. Finally, analysis of multiple single unit recordings requires accurate methods to correct for non-stationarity in unit firing. A novel technique for such correction is discussed.

Derivation of a vector model for a Brushless Doubly-Fed Machine with multiple loops per nest

The paper presents a vector model for a Brushless Doubly-Fed Machine (BDFM). The BDFM has 4 and 8 pole stator windings and a nested-loop rotor cage. The rotor cage has six nests equally spaced around the circumference and each nest comprises three loops. All the rotor loops are short circuited via a common end-ring at one end. The vector model is derived based on the electrical equations of the machine and appropriate vector transformations. In contrast to the stator, there is no three phase circuit in the rotor. Therefore, the vector transformations suitable for three phase circuits can not be utilised for the rotor circuit. A new vector transformation is employed for the rotor circuit quantities. The approach presented in this paper can be extended for a BDFM with any stator poles combination and any number of loops per nest. Simulation results from the model implemented in Simulink are presented. © 2008 IEEE.

Compression techniques applied to multiple speech recognition systems

Speech recognition systems typically contain many Gaussian distributions, and hence a large number of parameters. This makes them both slow to decode speech, and large to store. Techniques have been proposed to decrease the number of parameters. One approach is to share parameters between multiple Gaussians, thus reducing the total number of parameters and allowing for shared likelihood calculation. Gaussian tying and subspace clustering are two related techniques which take this approach to system compression. These techniques can decrease the number of parameters with no noticeable drop in performance for single systems. However, multiple acoustic models are often used in real speech recognition systems. This paper considers the application of Gaussian tying and subspace compression to multiple systems. Results show that two speech recognition systems can be modelled using the same number of Gaussians as just one system, with little effect on individual system performance. Copyright © 2009 ISCA.

A Computer integrated unified modelling approach to responsive manufacturing

Computer modelling approaches have significant potential to enable decision-making about various aspects of responsive manufacturing. In order to understand the system prior to the selection of any responsiveness strategy, multiple process segments of organisations need to be modelled. The article presents a novel systematic approach for creating coherent sets of unified enterprise, simulation and other supporting models that collectively facilitate responsiveness. In this approach, enterprise models are used to explicitly define relatively enduring relationships between (i) production planning and control (PPC) processes, that implement a particular strategy and (ii) process-oriented elements of production systems, that are work loaded by the PPC processes. Coherent simulation models, can in part be derived from the enterprise models, so that they computer execute production system behaviours. In this way, time-based performance outcomes can be simulated; so that the impacts of alternative PPC strategies on the planning and controlling historical or forecasted patterns of workflow, through (current and possible future) production system models, can be analysed. The article describes the unified modelling approach conceived and its application in a furniture industry case study small and medium enterprise (SME). Copyright © 2010 Inderscience Enterprises Ltd.

A structured modelling approach to simulating dynamic behaviours in complex organisations

This article reports a case study application of a systematic approach to modelling complex organisations, centred on simulation modelling (SM). The approach leads to populated instances of complementary model types, in ways that systematically capture, validate and facilitate various uses of organisational understandings, knowledge and data normally distributed amongst multiple knowledge holders. The model-driven approach to decision making enables improved manufacturing responsiveness. Literature on modelling technologies relevant to manufacturing systems organisation design and change is presented, as is literature on production planning and control. This provides a rationale for the development of a new modelling methodology which combines the use of enterprise, causal loop and SM. Subsequently, this article describes how in the case of a specific manufacturing enterprise the combined modelling techniques have informed the choice of alternative production planning and control policies. An example enterprise model of a capacitor manufacturing company is illustrated as derivative causal-loop models that structure and enable the design and use of a general purpose simulation model.

Adaptive sequential Monte Carlo approach for real-time applications

This paper presents an adaptive Sequential Monte Carlo approach for real-time applications. Sequential Monte Carlo method is employed to estimate the states of dynamic systems using weighted particles. The proposed approach reduces the run-time computation complexity by adapting the size of the particle set. Multiple processing elements on FPGAs are dynamically allocated for improved energy efficiency without violating real-time constraints. A robot localisation application is developed based on the proposed approach. Compared to a non-adaptive implementation, the dynamic energy consumption is reduced by up to 70% without affecting the quality of solutions. © 2012 IEEE.

A body force-based method for prediction of multiple-pure-tone noise: Validation

Emissions, fuel burn, and noise are the main drivers for innovative aircraft design. Embedded propulsion systems, such as for example used in hybrid-wing body aircraft, can offer fuel burn and noise reduction benefits but the impact of inlet flow distortion on the generation and propagation of turbomachinery noise has yet to be assessed. A novel approach is used to quantify the effects of non-uniform flow on the creation and propagation of multiple pure tone (MPT) noise. The ultimate goal is to conduct a parametric study of S-duct inlets to quantify the effects of inlet design parameters on the acoustic signature. The key challenge is that the effects of distortion transfer, noise source generation and propagation through the non-uniform flow field are inherently coupled such that a simultaneous computation of the aerodynamics and acoustics is required to capture the mechanisms at play. The technical approach is based on a body force description of the fan blade row that is able to capture the distortion transfer and the blade-to-blade flow variations that cause the MPT noise while reducing computational cost. A single, 3-D full-wheel CFD simulation, in which the Euler equations are solved to second-order spatial and temporal accuracy, simultaneously computes the MPT noise generation and its propagation in distorted inlet flow. A new method of producing the blade-to-blade variations in the body force field for MPT noise generation has been developed and validated. The numerical dissipation inherent to the solver is quantified and used to correct for non-physical attenuation in the far-field noise spectra. Source generation, acoustic propagation and acoustic energy transfer between modes is examined in detail. The new method is validated on NASA's Source Diagnostic Test fan and inlet, showing good agreement with experimental data for aerodynamic performance, acoustic source generation, and far-field noise spectra. The next steps involve the assessment of MPT noise in serpentine inlet ducts and the development of a reduced order formulation suitable for incorporation into NASA's ANOPP framework. © 2010 by Jeff Defoe, Alex Narkaj & Zoltan Spakovszky.

Reliability analysis of deep excavation based on a semi-empirical approach

The design and construction of deep excavations in urban environment is often governed by serviceability limit state related to the risk of damage to adjacent buildings. In current practice, the assessment of excavation-induced building damage has focused on a deterministic approach. This paper presents a component/system reliability analysis framework to assess the probability that specified threshold design criteria for multiple serviceability limit states are exceeded. A recently developed Bayesian probabilistic framework is used to update the predictions of ground movements in the later stages of excavation based on the recorded deformation measurements. An example is presented to show how the serviceability performance for excavation problems can be assessed based on the component/system reliability analysis. © 2011 ASCE.

A hybrid systems approach to trajectory tracking control for juggling systems

From a hybrid systems point of view, we provide a modeling framework and a trajectory tracking control design methodology for juggling systems. We present the main ideas and concepts in a one degree-of-freedom juggler, which consists of a ball bouncing on an actuated robot. We design a hybrid control strategy that, with only information of the ball's state at impacts, controls the ball to track a reference rhythmic pattern with arbitrary precision. We extend this hybrid control strategy to the case of juggling multiple balls with different rhythmic patterns. Simulation results for juggling of one and three balls with a single actuated robot are presented. © 2007 IEEE.