Tapered bow-tie lasers for high energy Q-switched pulse generation

A new kind of Q switched laser, the bow tie laser is introduced. This type of laser permits large area facets at both ends so that generation of high optical powers involve low optical intensities to prevent optical damage. The incorporation of doubled tapered waveguide structure to the Q switched multicontact laser has increased the optical pulse energies and peak powers of the laser.

Gain-switched dynamics of tapered waveguide bow-tie lasers

The use of tapered waveguide lasers and amplifiers for enhanced picosecond pulse generation has led to order-of-magnitude peak power and pulse energy improvements. Monolithic pulse generation schemes have so far relied on a double-tapered bow-tie structure. The modeling of tapered lasers has so far been limited to steady-state operation or has lacked experimental comparison. This paper considers both experimentally and theoretically the gain-switched performance of bow-tie lasers of various taper angles. The role of transverse-mode spatial hole burning in tapered waveguide lasers is thereby investigated.

Investigation of the losses in the stator duct spacers of large A.C. motors using the A -ip 3-D eddy current formulation

This paper describes how the A -if) formulation may be applied to determine the losses in the stator duct spacers of large a.c. motors. The model is described in terms of its geometry and boundary conditions. The novel aspects of the application of the formulation to this problem are explained. These include the modelling of fixed currents sources (the stator windings), the location of the necessary cut surfaces and the determination of their magnetic scalar potential differences, and the implementation of periodic boundary conditions for vector variables. Results are presented showing how the duct spacer losses vary with load, and with the relative permeability of the spacer material. The effects of modelling iron nonlinearity, of both the spacer and the steel laminations, are also illustrated. © 1996 IEEE.

Effects of pedestal suppression on gain-switched laser sources for 40 Gbit/s OTDM transmission

The performance of 40 Gbit/s optical time-division multiplexed (OTDM) communication systems can be severely limited when the extinction ratio of the optical pulses is low. This is a consequence of the coherent interference noise between individual OTDM channels. When taken alone, the multiple quantum well-distributed feedback laser+dispersion compensating fiber source exhibits a relatively poor extinction ratio which impairs its potential for use in a 40 Gbit/s OTDM system. However, with the addition of an electroabsorption modulator to suppress the pulse pedestals to better than 30 dB extinction, coherent interference noise is reduced, the bit-error-rate performance is greatly improved, and the source shows good potential for 40 Gbit/s OTDM communication.

10-Gbits/s all-optical 3R regeneration and format conversion using a gain-switched DFB laser

A strain-compensated multiple quantum well device is used as a DFB laser, this has been optimized for low jitter gain switched operation at 10 GHz. The signal is transmitted down 80 km of standard fiber then amplified, filtered and polarization controlled before being injected into a DFB laser. The purpose of this regeneration process is to gain switch the DFB with the extracted clock signal in order to retime the converted signal. This process also simultaneously converts the input NRZ format to an output RZ data to format and results in a signal whose optical power and extinction ratio are considerably improved by the regeneration process.

High-power and picosecond pulse generation from a passively Q-switched tapered InGaAs/GaAs laser

Tapered waveguides have been used for enhancing pulse powers in Q-switched AlGaAs and InGaAsP lasers. This paper reports on passively Q-switched pulses with 1.53 W peak power and 41-ps FWHM from an InGaAs/GasAs (970 nm) double-contact tapered semiconductor laser in a well defined single-lobed far-field.

Power losses in small inverter-fed induction motors

This paper presents the results of experimental and simulation investigations of the breakdown of losses in a small inverter fed induction motor. Factors that are considered include the impact of skew, excitation voltage waveform shape and PWM switching frequency. Detailed finite element simulations of the motor performance are carried out for the various conditions, with simulation results compared to calorimetric test results. © 2005 IEEE.