Influence of nutrient intake on antioxidant capacity, muscle damage and white blood cell count in female soccer players

11 p.

Talla 38

Duración (en horas): De 11 a 20 horas. Destinatario: Estudiante y Docente

"Talla 38"

Capítulo 6 del libro: Guisasola, Jenaro ; Garmendia, Mikel (eds.) "Aprendizaje basado en problemas, proyectos y casos: diseño e implementación de experiencias en la universidad" (ISBN: 978-84-9860-959-2)

Advanced Reaction Systems for Hydrogen Production

[EN] This PhD work started in March 2010 with the support of the University of the Basque Country (UPV/EHU) under the program named “Formación de Personal Investigador” at the Chemical and Environmental Engineering Department in the Faculty of Engineering of Bilbao. The major part of the Thesis work was carried out in the mentioned department, as a member of the Sustainable Process Engineering (SuPrEn) research group. In addition, this PhD Thesis includes the research work developed during a period of 6 months at the Institut für Mikrotechnik Mainz GmbH, IMM, in Germany. During the four years of the Thesis, conventional and microreactor systems were tested for several feedstocks renewable and non-renewable, gases and liquids through several reforming processes in order to produce hydrogen. For this purpose, new catalytic formulations which showed high activity, selectivity and stability were design. As a consequence, the PhD work performed allowed the publication of seven scientific articles in peer-reviewed journals. This PhD Thesis is divided into the following six chapters described below. The opportunity of this work is established on the basis of the transition period needed for moving from a petroleum based energy system to a renewable based new one. Consequently, the present global energy scenario was detailed in Chapter 1, and the role of hydrogen as a real alternative in the future energy system was justified based on several outlooks. Therefore, renewable and non-renewable hydrogen production routes were presented, explaining the corresponding benefits and drawbacks. Then, the raw materials used in this Thesis work were described and the most important issues regarding the processes and the characteristics of the catalytic formulations were explained. The introduction chapter finishes by introducing the concepts of decentralized production and process intensification with the use of microreactors. In addition, a small description of these innovative reaction systems and the benefits that entailed their use were also mentioned. In Chapter 2 the main objectives of this Thesis work are summarized. The development of advanced reaction systems for hydrogen rich mixtures production is the main objective. In addition, the use and comparison between two different reaction systems, (fixed bed reactor (FBR) and microreactor), the processing of renewable raw materials, the development of new, active, selective and stable catalytic formulations, and the optimization of the operating conditions were also established as additional partial objectives. Methane and natural gas (NG) steam reforming experimental results obtained when operated with microreactor and FBR systems are presented in Chapter 3. For these experiments nickel-based (Ni/Al2O3 and Ni/MgO) and noble metal-based (Pd/Al2O3 and Pt/Al2O3) catalysts were prepared by wet impregnation and their catalytic activity was measured at several temperatures, from 973 to 1073 K, different S/C ratios, from 1.0 to 2.0, and atmospheric pressure. The Weight Hourly Space Velocity (WHSV) was maintained constant in order to compare the catalytic activity in both reaction systems. The results obtained showed a better performance of the catalysts operating in microreactors. The Ni/MgO catalyst reached the highest hydrogen production yield at 1073 K and steam-to-carbon ratio (S/C) of 1.5 under Steam methane Reforming (SMR) conditions. In addition, this catalyst also showed good activity and stability under NG reforming at S/C=1.0 and 2.0. The Ni/Al2O3 catalyst also showed high activity and good stability and it was the catalyst reaching the highest methane conversion (72.9 %) and H2out/CH4in ratio (2.4) under SMR conditions at 1073 K and S/C=1.0. However, this catalyst suffered from deactivation when it was tested under NG reforming conditions. Regarding the activity measurements carried out with the noble metal-based catalysts in the microreactor systems, they suffered a very quick deactivation, probably because of the effects attributed to carbon deposition, which was detected by Scanning Electron Microscope (SEM). When the FBR was used no catalytic activity was measured with the catalysts under investigation, probably because they were operated at the same WHSV than the microreactors and these WHSVs were too high for FBR system. In Chapter 4 biogas reforming processes were studied. This chapter starts with an introduction explaining the properties of the biogas and the main production routes. Then, the experimental procedure carried out is detailed giving concrete information about the experimental set-up, defining the parameters measured, specifying the characteristics of the reactors used and describing the characterization techniques utilized. Each following section describes the results obtained from activity testing with the different catalysts prepared, which is subsequently summarized: Section 4.3: Biogas reforming processes using γ-Al2O3 based catalysts The activity results obtained by several Ni-based catalysts and a bimetallic Rh-Ni catalyst supported on magnesia or alumina modified with oxides like CeO2 and ZrO2 are presented in this section. In addition, an alumina-based commercial catalyst was tested in order to compare the activity results measured. Four different biogas reforming processes were studied using a FBR: dry reforming (DR), biogas steam reforming (BSR), biogas oxidative reforming (BOR) and tri-reforming (TR). For the BSR process different steam to carbon ratios (S/C) from 1.0 to 3.0, were tested. In the case of BOR process the oxygen-to-methane (O2/CH4) ratio was varied from 0.125 to 0.50. Finally, for TR processes different S/C ratios from 1.0 to 3.0, and O2/CH4 ratios of 0.25 and 0.50 were studied. Then, the catalysts which achieved high activity and stability were impregnated in a microreactor to explore the viability of process intensification. The operation with microreactors was carried out under the best experimental conditions measured in the FBR. In addition, the physicochemical characterization of the fresh and spent catalysts was carried out by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), N2 physisorption, H2 chemisorption, Temperature Programmed Reduction (TPR), SEM, X-ray Photoelectron Spectroscopy (XPS) and X-ray powder Diffraction (XRD). Operating with the FBR, conversions close to the ones predicted by thermodynamic calculations were obtained by most of the catalysts tested. The Rh-Ni/Ce-Al2O3 catalyst obtained the highest hydrogen production yield in DR. In BSR process, the Ni/Ce-Al2O3 catalyst achieved the best activity results operating at S/C=1.0. In the case of BOR process, the Ni/Ce-Zr-Al2O3 catalyst showed the highest reactants conversion values operating at O2/CH4=0.25. Finally, in the TR process the Rh-Ni/Ce-Al2O3 catalyst obtained the best results operating at S/C=1.0 and O2/CH4=0.25. Therefore, these three catalysts were selected to be coated onto microchannels in order to test its performance under BOR and TR processes conditions. Although the operation using microreactors was carried out under considerably higher WHSV, similar conversions and yields as the ones measured in FBR were measured. Furthermore, attending to other measurements like Turnover Frequency (TOF) and Hydrogen Productivity (PROD), the values calculated for the catalysts tested in microreactors were one order of magnitude higher. Thus, due to the low dispersion degree measured by H2-chemisorption, the Ni/Ce-Al2O3 catalyst reached the highest TOF and PROD values. Section 4.4: Biogas reforming processes using Zeolites L based catalysts In this section three type of L zeolites, with different morphology and size, were synthesized and used as catalyst support. Then, for each type of L zeolite three nickel monometallic and their homologous Rh-Ni bimetallic catalysts were prepared by the wetness impregnation method. These catalysts were tested using the FBR under DR process and different conditions of BSR (S/C ratio of 1.0 and 2.0), BOR (O2/CH4 ratio of 0.25 and 0.50) and TR processes (at S/C=1.0 and O2/CH4=0.25). The characterization of these catalysts was also carried out by using the same techniques mentioned in the previous section. Very high methane and carbon dioxide conversion values were measured for almost all the catalysts under investigation. The experimental results evidenced the better catalytic behavior of the bimetallic catalysts as compared to the monometallic ones. Comparing the catalysts behavior with regards to their morphology, for the BSR process the Disc catalysts were the most active ones at the lowest S/C ratio tested. On the contrary, the Cylindrical (30–60 nm) catalysts were more active under BOR conditions at O2/CH4=0.25 and TR processes. By the contrary, the Cylindrical (1–3 µm) catalysts showed the worst activity results for both processes. Section 4.5: Biogas reforming processes using Na+ and Cs+ doped Zeolites LTL based catalysts A method for the synthesis of Linde Type L (LTL) zeolite under microwave-assisted hydrothermal conditions and its behavior as a support for heterogeneously catalyzed hydrogen production is described in this section. Then, rhodium and nickel-based bimetallic catalysts were prepared in order to be tested by DR process and BOR process at O2/CH4=0.25. Moreover, the characterization of the catalysts under investigation was also carried out. Higher activities were achieved by the catalysts prepared from the non-doped zeolites, Rh-Ni/D and Rh-Ni/N, as compared to the ones supported on Na+ and Cs+ exchanged supports. However, the differences between them were not very significant. In addition, the Na+ and Cs+ incorporation affected mainly to the Disc catalysts. Comparing the results obtained by these catalysts with the ones studied in the section 4.4, in general worst results were achieved under DR conditions and almost the same results when operated under BOR conditions. In Chapter 5 the ethylene glycol (EG) as feed for syngas production by steam reforming (SR) and oxidative steam reforming (OSR) was studied by using microchannel reactors. The product composition was determined at a S/C of 4.0, reaction temperatures between 625°C and 725°C, atmospheric pressure and Volume Hourly Space Velocities (VHSV) between 100 and 300 NL/(gcath). This work was divided in two sections. The first one corresponds to the introduction of the main and most promising EG production routes. Then, the new experimental procedure is detailed and the information about the experimental set-up and the measured parameters is described. The characterization was carried out using the same techniques as for the previous chapter. Then, the next sections correspond to the catalytic activity and catalysts characterization results. Section 5.3: xRh-cm and xRh-np catalysts for ethylene glycol reforming Initially, catalysts with different rhodium loading, from 1.0 to 5.0 wt. %, and supported on α-Al2O3 were prepared by two different preparation methods (conventional impregnation and separate nanoparticle synthesis). Then, the catalysts were compared regarding their measured activity and selectivity, as well as the characterization results obtained before and after the activity tests carried out. The samples prepared by a conventional impregnation method showed generally higher activity compared to catalysts prepared from Rh nanoparticles. By-product formation of species such as acetaldehyde, ethane and ethylene was detected, regardless if oxygen was added to the feed or not. Among the catalysts tested, the 2.5Rh-cm catalyst was considered the best one. Section 5.4: 2.5Rh-cm catalyst support modification with CeO2 and La2O3 In this part of the Chapter 5, the catalyst showing the best performance in the previous section, the 2.5Rh-Al2O3 catalyst, was selected in order to be improved. Therefore, new Rh based catalysts were designed using α-Al2O3 and being modified this support with different contents of CeO2 or La2O3 oxides. All the catalysts containing additives showed complete conversion and selectivities close to the equilibrium in both SR and OSR processes. In addition, for these catalysts the concentrations measured for the C2H4, CH4, CH3CHO and C2H6 by-products were very low. Finally, the 2.5Rh-20Ce catalyst was selected according to its catalytic activity and characterization results in order to run a stability test, which lasted more than 115 hours under stable operation. The last chapter, Chapter 6, summarizes the main conclusions achieved throughout this Thesis work. Although very high reactant conversions and rich hydrogen mixtures were obtained using a fixed bed reaction system, the use of microreactors improves the key issues, heat and mass transfer limitations, through which the reforming reactions are intensified. Therefore, they seem to be a very interesting and promising alternative for process intensification and decentralized production for remote application.

Addressing students' difficulties with Faraday's law: A guided problem solving approach

In traditional teaching, the fundamental concepts of electromagnetic induction are usually quickly analyzed, spending most of the time solving problems in a more or less rote manner. However, physics education research has shown that the fundamental concepts of the electromagnetic induction theory are barely understood by students. This article proposes an interactive teaching sequence introducing the topic of electromagnetic induction. The sequence has been designed based on contributions from physics education research. Particular attention is paid to the relationship between experimental findings (macroscopic level) and theoretical interpretation (microscopic level). An example of the activities that have been designed will also be presented, describing the implementation context and the corresponding findings. Since implementing the sequence, a considerable number of students have a more satisfactory grasp of the electromagnetic induction explicative model. However, difficulties are manifested in aspects that require a multilevel explanation, referring to deep structures where the system description is better defined.

Hezkuntza sistemaren erantzuna autismoa duen ikasleriari eskola inklusiboaren ikuspuntutik

PDFs sin acceso a petición de la autora

Sintesi hidrotermal bidezko titanio dioxidozko nanohodien lorpena

[EUS] Gaur egun nanozientzia zientzia eta teknologia arlo guztietara zabaldu da, gizarte garapenean eragin handia izan du. Ikerkuntza arlo guztietara zabaldu da ezinezkoak ziruditen erronkak argitu eta ezezagunak ditugun ezagutzak garatzeko asmoz. Lan honetan TiO2 nanohagatxoen sintesia burutu da metodo hidrotermala erabiliz. Sintesi baldintzek lortutako produktuaren egituran eta forman duten eragina kontuan harturik, sintesia gertatzeko ezinbestekoak diren pHa, tenperatura eta denbora aztertu dira. Ondoren, tratamendu kimiko eta termiko ezberdinen bidez konposizio eta egitura ezberdinak lor daitezkeela frogatu da. Bereziki, surfaktante eta pHaren arabera egitura ezberdinak lortzen direla ikusirik. Sintetizatutako laginen karakterizazioa burutzeko X izpien difrakzioa, transmisio bidezko mikroskopia elektronikoa, infragorri espektroskopia, eta termograbimetria teknikak erabili dira. Hauen bidez NaTi3O6·(OH)x·(H2O)y , (TiO2)x(H2O)y , anatasa eta rutilo faseak identifikatu dira, eta nanohagatxoen lodiera eta morfologia ezberdinak ikusi dira.

Desarrollo de catalizadores en sistemas de reacción avanzados para la producción de hidrógeno a partir de biogás

[ES]En el presente documento se expone el estudio experimental que consiste en la comparación de diferentes catalizadores en sistemas de reacción avanzados, microrreactores, para la producción de hidrógeno a partir de biogás. El hidrógeno es un vector energético que puede emplearse como combustible, y por tanto, un candidato perfecto para sustituir aquellos combustibles provenientes de fuentes fósiles. Este Proyecto de Fin de Grado se ha basado en desarrollar el proceso conocido como tri-reformado de biogás. Esta técnica, al contrario que las técnicas convencionales de producción, presenta numerosas ventajas ya que la materia prima empleada, el biogás, es una fuente de origen renovable. Para llevar a cabo este estudio se han preparado distintos catalizadores, basados todos ellos en platino. La elección de este metal noble es debido a su alto grado de reactividad, especialmente en sistemas de reacción micro-estructurados. Con el objetivo de reducir los costes asociados al propio catalizador, se añadieron, junto con el platino, otros metales más baratos a fin de analizar su idoneidad en el proceso del tri-reformado. Por tanto, partiendo de un catalizador de referencia que contiene un 5% de platino, se prepararon otros catalizadores mantenido constante, en un 5%, la composición de metal total. Estos catalizadores se han denominado de la siguiente manera: 2.5(Pt-Me), siendo Me cada especie metálica diferente. Tras preparar los catalizadores, se llevaron a cabo diferentes experimentos con un reactor convencional de lecho fijo. El objetivo fue establecer unas condiciones de operación tal que asegurasen una adecuada comparación entre catalizadores. De este modo, se realizaron ensayos de actividad catalítica a diferentes temperaturas y velocidades espaciales para someter a los catalizadores a condiciones de operación extremas, bajo las cuales, las diferencias entre catalizadores fueran más notorias. Una vez detalladas las condiciones de operación adecuadas para la comparación de catalizadores, se llevaron a cabo los correspondientes ensayos con los catalizadores impregnados en los sistemas de reacción avanzados, denominados micorreactores. Estos ensayos se basaron en operar a una velocidad espacial constante para estudiar la influencia de la temperatura. Además, se llevaron a cabo ensayos de estabilidad de hasta 110 horas en las condiciones de operación más desfavorables. Por último se compararon las conversiones de CH4 y CO2 y el rendimiento de H2 de todas las formulaciones catalíticas preparadas, y se concluyó que el mejor candidato para el proceso del tri-reformado es el catalizador 2.5(Pt-Pd).

El tratamiento en IRPF de los bienes afectos a actividades económicas: País Vasco versus territorio común

El objetivo de este trabajo es analizar el tratamiento de los bienes afectos a las actividades económicas en el País Vasco y Territorio Común. El análisis se vertebra a tres niveles. En primer lugar, se realiza una comparación de las tres normativas forales aplicadas en 2013, así como un estudio de las variaciones que estas normativas han sufrido en 2015 y su repercusión en el contribuyente. En segundo lugar, se analizan las diferencias de la normativa estatal con respecto a las normativas forales aplicables en 2013 analizadas en el bloque anterior. Algunas de las diferencias que se han encontrado se encuentran en la determinación de los rendimientos netos o escalas de gravamen. Finalmente, en el tercer bloque se aplican los tratamientos de las normativas a los bienes afectos y a las actividades económicas mediante tres supuestos. En el primer supuesto se comparan los tratamientos que reciben las ganancias patrimoniales en las normativas. En el segundo supuesto se realiza una tabla de comparación para la visualización de los tratamientos de las pérdidas patrimoniales de los bienes afectos si el rendimiento neto resultara positivo o bien si resultara negativo. En el tercer supuesto se analiza el cálculo del rendimiento neto según las diferentes metodologías y normativas. El proyecto se ha realizado en español.