Advanced Reaction Systems for Hydrogen Production

[EN] This PhD work started in March 2010 with the support of the University of the Basque Country (UPV/EHU) under the program named “Formación de Personal Investigador” at the Chemical and Environmental Engineering Department in the Faculty of Engineering of Bilbao. The major part of the Thesis work was carried out in the mentioned department, as a member of the Sustainable Process Engineering (SuPrEn) research group. In addition, this PhD Thesis includes the research work developed during a period of 6 months at the Institut für Mikrotechnik Mainz GmbH, IMM, in Germany. During the four years of the Thesis, conventional and microreactor systems were tested for several feedstocks renewable and non-renewable, gases and liquids through several reforming processes in order to produce hydrogen. For this purpose, new catalytic formulations which showed high activity, selectivity and stability were design. As a consequence, the PhD work performed allowed the publication of seven scientific articles in peer-reviewed journals. This PhD Thesis is divided into the following six chapters described below. The opportunity of this work is established on the basis of the transition period needed for moving from a petroleum based energy system to a renewable based new one. Consequently, the present global energy scenario was detailed in Chapter 1, and the role of hydrogen as a real alternative in the future energy system was justified based on several outlooks. Therefore, renewable and non-renewable hydrogen production routes were presented, explaining the corresponding benefits and drawbacks. Then, the raw materials used in this Thesis work were described and the most important issues regarding the processes and the characteristics of the catalytic formulations were explained. The introduction chapter finishes by introducing the concepts of decentralized production and process intensification with the use of microreactors. In addition, a small description of these innovative reaction systems and the benefits that entailed their use were also mentioned. In Chapter 2 the main objectives of this Thesis work are summarized. The development of advanced reaction systems for hydrogen rich mixtures production is the main objective. In addition, the use and comparison between two different reaction systems, (fixed bed reactor (FBR) and microreactor), the processing of renewable raw materials, the development of new, active, selective and stable catalytic formulations, and the optimization of the operating conditions were also established as additional partial objectives. Methane and natural gas (NG) steam reforming experimental results obtained when operated with microreactor and FBR systems are presented in Chapter 3. For these experiments nickel-based (Ni/Al2O3 and Ni/MgO) and noble metal-based (Pd/Al2O3 and Pt/Al2O3) catalysts were prepared by wet impregnation and their catalytic activity was measured at several temperatures, from 973 to 1073 K, different S/C ratios, from 1.0 to 2.0, and atmospheric pressure. The Weight Hourly Space Velocity (WHSV) was maintained constant in order to compare the catalytic activity in both reaction systems. The results obtained showed a better performance of the catalysts operating in microreactors. The Ni/MgO catalyst reached the highest hydrogen production yield at 1073 K and steam-to-carbon ratio (S/C) of 1.5 under Steam methane Reforming (SMR) conditions. In addition, this catalyst also showed good activity and stability under NG reforming at S/C=1.0 and 2.0. The Ni/Al2O3 catalyst also showed high activity and good stability and it was the catalyst reaching the highest methane conversion (72.9 %) and H2out/CH4in ratio (2.4) under SMR conditions at 1073 K and S/C=1.0. However, this catalyst suffered from deactivation when it was tested under NG reforming conditions. Regarding the activity measurements carried out with the noble metal-based catalysts in the microreactor systems, they suffered a very quick deactivation, probably because of the effects attributed to carbon deposition, which was detected by Scanning Electron Microscope (SEM). When the FBR was used no catalytic activity was measured with the catalysts under investigation, probably because they were operated at the same WHSV than the microreactors and these WHSVs were too high for FBR system. In Chapter 4 biogas reforming processes were studied. This chapter starts with an introduction explaining the properties of the biogas and the main production routes. Then, the experimental procedure carried out is detailed giving concrete information about the experimental set-up, defining the parameters measured, specifying the characteristics of the reactors used and describing the characterization techniques utilized. Each following section describes the results obtained from activity testing with the different catalysts prepared, which is subsequently summarized: Section 4.3: Biogas reforming processes using γ-Al2O3 based catalysts The activity results obtained by several Ni-based catalysts and a bimetallic Rh-Ni catalyst supported on magnesia or alumina modified with oxides like CeO2 and ZrO2 are presented in this section. In addition, an alumina-based commercial catalyst was tested in order to compare the activity results measured. Four different biogas reforming processes were studied using a FBR: dry reforming (DR), biogas steam reforming (BSR), biogas oxidative reforming (BOR) and tri-reforming (TR). For the BSR process different steam to carbon ratios (S/C) from 1.0 to 3.0, were tested. In the case of BOR process the oxygen-to-methane (O2/CH4) ratio was varied from 0.125 to 0.50. Finally, for TR processes different S/C ratios from 1.0 to 3.0, and O2/CH4 ratios of 0.25 and 0.50 were studied. Then, the catalysts which achieved high activity and stability were impregnated in a microreactor to explore the viability of process intensification. The operation with microreactors was carried out under the best experimental conditions measured in the FBR. In addition, the physicochemical characterization of the fresh and spent catalysts was carried out by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), N2 physisorption, H2 chemisorption, Temperature Programmed Reduction (TPR), SEM, X-ray Photoelectron Spectroscopy (XPS) and X-ray powder Diffraction (XRD). Operating with the FBR, conversions close to the ones predicted by thermodynamic calculations were obtained by most of the catalysts tested. The Rh-Ni/Ce-Al2O3 catalyst obtained the highest hydrogen production yield in DR. In BSR process, the Ni/Ce-Al2O3 catalyst achieved the best activity results operating at S/C=1.0. In the case of BOR process, the Ni/Ce-Zr-Al2O3 catalyst showed the highest reactants conversion values operating at O2/CH4=0.25. Finally, in the TR process the Rh-Ni/Ce-Al2O3 catalyst obtained the best results operating at S/C=1.0 and O2/CH4=0.25. Therefore, these three catalysts were selected to be coated onto microchannels in order to test its performance under BOR and TR processes conditions. Although the operation using microreactors was carried out under considerably higher WHSV, similar conversions and yields as the ones measured in FBR were measured. Furthermore, attending to other measurements like Turnover Frequency (TOF) and Hydrogen Productivity (PROD), the values calculated for the catalysts tested in microreactors were one order of magnitude higher. Thus, due to the low dispersion degree measured by H2-chemisorption, the Ni/Ce-Al2O3 catalyst reached the highest TOF and PROD values. Section 4.4: Biogas reforming processes using Zeolites L based catalysts In this section three type of L zeolites, with different morphology and size, were synthesized and used as catalyst support. Then, for each type of L zeolite three nickel monometallic and their homologous Rh-Ni bimetallic catalysts were prepared by the wetness impregnation method. These catalysts were tested using the FBR under DR process and different conditions of BSR (S/C ratio of 1.0 and 2.0), BOR (O2/CH4 ratio of 0.25 and 0.50) and TR processes (at S/C=1.0 and O2/CH4=0.25). The characterization of these catalysts was also carried out by using the same techniques mentioned in the previous section. Very high methane and carbon dioxide conversion values were measured for almost all the catalysts under investigation. The experimental results evidenced the better catalytic behavior of the bimetallic catalysts as compared to the monometallic ones. Comparing the catalysts behavior with regards to their morphology, for the BSR process the Disc catalysts were the most active ones at the lowest S/C ratio tested. On the contrary, the Cylindrical (30–60 nm) catalysts were more active under BOR conditions at O2/CH4=0.25 and TR processes. By the contrary, the Cylindrical (1–3 µm) catalysts showed the worst activity results for both processes. Section 4.5: Biogas reforming processes using Na+ and Cs+ doped Zeolites LTL based catalysts A method for the synthesis of Linde Type L (LTL) zeolite under microwave-assisted hydrothermal conditions and its behavior as a support for heterogeneously catalyzed hydrogen production is described in this section. Then, rhodium and nickel-based bimetallic catalysts were prepared in order to be tested by DR process and BOR process at O2/CH4=0.25. Moreover, the characterization of the catalysts under investigation was also carried out. Higher activities were achieved by the catalysts prepared from the non-doped zeolites, Rh-Ni/D and Rh-Ni/N, as compared to the ones supported on Na+ and Cs+ exchanged supports. However, the differences between them were not very significant. In addition, the Na+ and Cs+ incorporation affected mainly to the Disc catalysts. Comparing the results obtained by these catalysts with the ones studied in the section 4.4, in general worst results were achieved under DR conditions and almost the same results when operated under BOR conditions. In Chapter 5 the ethylene glycol (EG) as feed for syngas production by steam reforming (SR) and oxidative steam reforming (OSR) was studied by using microchannel reactors. The product composition was determined at a S/C of 4.0, reaction temperatures between 625°C and 725°C, atmospheric pressure and Volume Hourly Space Velocities (VHSV) between 100 and 300 NL/(gcath). This work was divided in two sections. The first one corresponds to the introduction of the main and most promising EG production routes. Then, the new experimental procedure is detailed and the information about the experimental set-up and the measured parameters is described. The characterization was carried out using the same techniques as for the previous chapter. Then, the next sections correspond to the catalytic activity and catalysts characterization results. Section 5.3: xRh-cm and xRh-np catalysts for ethylene glycol reforming Initially, catalysts with different rhodium loading, from 1.0 to 5.0 wt. %, and supported on α-Al2O3 were prepared by two different preparation methods (conventional impregnation and separate nanoparticle synthesis). Then, the catalysts were compared regarding their measured activity and selectivity, as well as the characterization results obtained before and after the activity tests carried out. The samples prepared by a conventional impregnation method showed generally higher activity compared to catalysts prepared from Rh nanoparticles. By-product formation of species such as acetaldehyde, ethane and ethylene was detected, regardless if oxygen was added to the feed or not. Among the catalysts tested, the 2.5Rh-cm catalyst was considered the best one. Section 5.4: 2.5Rh-cm catalyst support modification with CeO2 and La2O3 In this part of the Chapter 5, the catalyst showing the best performance in the previous section, the 2.5Rh-Al2O3 catalyst, was selected in order to be improved. Therefore, new Rh based catalysts were designed using α-Al2O3 and being modified this support with different contents of CeO2 or La2O3 oxides. All the catalysts containing additives showed complete conversion and selectivities close to the equilibrium in both SR and OSR processes. In addition, for these catalysts the concentrations measured for the C2H4, CH4, CH3CHO and C2H6 by-products were very low. Finally, the 2.5Rh-20Ce catalyst was selected according to its catalytic activity and characterization results in order to run a stability test, which lasted more than 115 hours under stable operation. The last chapter, Chapter 6, summarizes the main conclusions achieved throughout this Thesis work. Although very high reactant conversions and rich hydrogen mixtures were obtained using a fixed bed reaction system, the use of microreactors improves the key issues, heat and mass transfer limitations, through which the reforming reactions are intensified. Therefore, they seem to be a very interesting and promising alternative for process intensification and decentralized production for remote application.

Regulación de las GTPasas de la familia Ras y la viabilidad de neuronas dopaminérgicas en respuesta a la señalización purinérgica

158 p.

Nanocomposites de Poliuretanos Elastoméricos y Nanotubos de Carbono Multipared

218p. -- Tesis con mención "Doctor europeus" realizada en el periodo de Octubre 2005-Mayo 2010, en el Grupo "Materiales+Tecnologías" (GMT).

Proceso catalítico de transformación de dimetil éter en olefinas (DTO)

325 p.

Auto-ensamblaje de unidades porfirínicas para la obtención de dispositivos supramoleculares

Comunicación presentada en: II Reunión de Jóvenes Cristalógrafos, 29 Sept-1 Oct de 2010, Bilbao, España

Modular Multimodal Iron Oxide-Based Nanocarriers for Image-Guided dsRNA Immunostimulation and Platinum Anticancer Drug Design

237 p.

Estudio de la resolución del problema de posición de mecanismos planos de cadena cerrada usando la Proyección cinemática de Study.

[ES]El presente documento versa sobre el desarrollo y posteriores resultados de un estudio elaborado en el campo de la cinemática teórica. Se plantea como objetivo del estudio mostrar las posibles ventajas que puede aportar el uso de la proyección cinemática tanto al análisis como a la síntesis de mecanismos. Los resultados obtenidos reflejan que la metodología propuesta para el análisis es adecuada para mecanismos sencillos, pero puede no serlo tanto para mecanismos de varios lazos cinemáticos. En cuanto al procedimiento propuesto para la síntesis, pese a obtenerse unos interesantes resultados, aún queda mucho por avanzar en ese campo.

Suplementación con Beta-Alanina y su efecto sobre el rendimiento deportivo con aplicación específica al fútbol

Hoy en día y con el objetivo de conseguir el mayor rendimiento posible en la mayoría de los deportes profesionales, la suplementación deportiva está adquiriendo un protagonismo vital, siendo conscientes de que la suplementación deportiva por sí sola no sea el principal factor responsable del aumento del rendimiento deportivo. Sin embargo, ha quedado demostrado que estos suplementos pueden ayudar a dar el salto de calidad en deportistas profesionales y últimamente salen a la luz investigaciones de nuevos suplementos que empiezan a ser habituales en algunos deportistas, como es el caso de la Beta-Alanina. El principal efecto de la ingesta exógena de b-alanina en el organismo radica en el aumento de la carnosina muscular debido a su rol como factor limitante en la síntesis de la misma, un dipéptido citoplasmático que tiene la capacidad de secuestrar los protones inducidos por el ejercicio de alta intensidad, retrasando la disminución del pH intramuscular y en consecuencia, retrasando la fatiga. La mayoría de los estudios hasta el momento que han investigado el efecto de la b-alanina y el rendimiento deportivo se centran en los deportes cíclicos, especialmente en aquellos deportes anaeróbicos donde la disminución del pH es limitante del rendimiento deportivo. Por ello, mediante una revisión bibliográfica el objetivo de este artículo será identificar y resumir los efectos principales de la suplementación exógena de Beta-alanina relacionados con el aumento del rendimiento deportivo y complementariamente, se realizar también un análisis sobre los factores fisiológicos del fútbol con el fin de conocer si este suplemento podría aumentar el rendimiento en los futbolistas de alto nivel.

Development of the heterogeneous catalysts for the production of levulinic acid from furfuryl alcohol

207 p.

Subjektu egozgarri eta arriskutsuen tratamendu penala

[ES]El presente Trabajo de Fin de Grado analiza el tratamiento penal de los sujetos imputables peligrosos que mantienen la peligrosidad criminal tras el cumplimiento de la pena de prisión. De esta manera, se investiga la regulación jurídica española dirigida a este colectivo, poniendo de manifiesto que hasta la entrada en vigor de la Ley Orgánica 5/2010 de reforma del Código Penal no había prevista ninguna medida de seguridad enfocada a este grupo específico y concluyendo que la medida de “libertad vigilada” introducida en dicha reforma no es del todo efectiva para alcanzar la reinserción del reo. Por todo ello, se argumenta que la política criminal llevada a cabo en los últimos años ha llevado la seguridad a un extremo tal que no se han podido garantizar del todo los derechos individuales del colectivo anteriormente mencionado. Asimismo, se investiga la “custodia de seguridad” vigente en la regulación alemana, haciendo notoria la importancia de la seguridad e inocuización. En síntesis, se estudia si el delincuente ha quedado subordinado al orden jurídico y a la seguridad, esclareciendo si han sido respetados los principios y garantías inherentes a un Estado Social y Democrático de Derecho.

SupraMOFs: Supramolecular porous materials assembled from metal-nucleobase discrete entities

289 p.

Exploring new labelling strategies for boronated compounds: towards fast development and efficient assessment of BNCT drug candidates

208 p.

Veintisiete años después del «Auriñaciense y Perigordiense en el País Vasco». Nuevas investigaciones de campo acerca del Paleolítico superior Inicial en el País Vasco

[ES] Veintisiete años después de la publicación de la primera síntesis sobre el Paleolítico superior inicial en el País Vasco, nos proponemos actualizar esta temática de acuerdo a los avances desarrollados en la investigación de campo a lo largo de estos años. Valoramos como un hito el citado artículo debido a diferentes motivos, que se exponen con cierto detalle en el texto. Debido a diferentes circunstancias (que intentaremos exponer), se detecta un desfase creciente entre actividad de campo y publicación de resultados, que de no corregirse puede dar lugar a excavaciones inéditas y, por tanto, no productivas.

Caracterización Molecular Y Epidemiológica de Cepas Monofásicas de Salmonella Enterica

225 p.

Estrategias para una VENTANA eficaz: Forma geométrica del HUECO - Diseño de la VENTANA-UH

V.1. 219 p.; V. 2. 589 p.