Meteorological Buoy Sensor Workshop, Solomons, Maryland, April 19-21, 2006: workshop proceedings

The co-organized Alliance for Coastal Technologies (ACT) and National Data Buoy Center (NDBC) Workshop "Meteorological Buoy Sensors Workshop" convened in Solomons, Maryland, April 19 to 21,2006, sponsored by the University of Maryland Center for Environmental Science (UMCES) Chesapeake Bay Laboratory (CBL), an ACT partner institution. Participants from various sectors including resource managers and industry representatives collaborated to focus on technologies and sensors that measure the near surface variables of wind speed and direction, barometric pressure, humidity and air temperature. The vendor list was accordingly targeted at companies that produced these types of sensors. The managers represented a cross section of federal, regional and academic marine observing interests from around the country. Workshop discussions focused on the challenges associated with making marine meteorological observations in general and problems that were specific to a particular variable. Discussions also explored methods to mitigate these challenges through the adoption of best practices, improved technologies and increased standardization. Some of the key workshop outcomes and recommendations included: 0cean.US should establish a committee devoted to observations. The committee would have a key role in developing observing standards. The community should adopt the target cost, reliability and performance standards drafted for a typical meteorological package to be used by a regional observing system. A forum should be established to allow users and manufacturers to share best practices for the employment of marine meteorological sensors. The ACT website would host the forum. Federal activities that evaluate meteorological sensors should make their results publicly available. ACT should extend their evaluation process to include meteorological sensors. A follow on workshop should be conducted that covers the observing of meteorological variables not addressed by this workshop. (pdf contains 18 pages)

What is coastal climate?

Historical definitions of what determines whether one lives in a coastal area or not have varied over time. According to Culliton (1998), a “coastal county” is defined as a county with at least 15% of its total land area located within a nation’s coastal watershed. This emphasizes the land areas within which water flows into the ocean or Great Lakes, but may be better suited for ecosystems or water quality research (Crowell et al. 2007). Some Federal Emergency Management Agency (FEMA) documents suggest that “coastal” includes shoreline-adjacent coastal counties, and perhaps even counties impacted by flooding from coastal storms. An accurate definition of “coastal” is critical in this regard since FEMA uses such definitions to revise and modernize their Flood Insurance Rate Maps (Crowell et al. 2007). A recent map published by the National Oceanic and Atmospheric Administration’s (NOAA) Coastal Services Center for the Coastal Change Analysis Program shows that the “coastal” boundary covers the entire state of New York and Michigan, while nearly all of South Carolina is considered “coastal.” The definition of “coastal” one chooses can have major implications, including a simple count of coastal population and the influence of local or state coastal policies. There is, however, one aspect of defining what is “coastal” that has often been overlooked; using atmospheric long-term climate variables to define the inland extent of the coastal zone. This definition, which incorporates temperature, precipitation, wind speed, and relative humidity, is furthermore scalable and globally applicable - even in the face of shifting shorelines. A robust definition using common climate variables should condense the large broad definition often associated with “coastal” such that completely landlocked locations would no longer be considered “coastal.” Moreover, the resulting definition, “coastal climate” or “climatology of the coast”, will help coastal resource managers make better-informed decisions on a wide range of climatologically-influenced issues. The following sections outline the methodology employed to derive some new maps of coastal boundaries in the United States. (PDF contains 3 pages)

Design for Survival: Sustainability for Planet and Structure

Buildings in Port Aransas encounter drastic environmental challenges: the potential catastrophic storm surge and high winds from a hurricane, and daily conditions hostile to buildings, vehicles, and even most vegetation. Its location a few hundred feet from the Gulf of Mexico and near-tropical latitude expose buildings to continuous high humidity, winds laden with scouring sand and corrosive salt, and extremes of temperature and ultraviolet light. Building construction methods are able to address each of these, but doing so in a sustainable way creates significant challenges. The new research building at the Marine Science Institute has been designed and is being constructed to meet the demand for both survivability and sustainability. It is tracking towards formal certification as a LEED Gold structure while being robust and resistant to the harsh coastal environment. The effects of a hurricane are mitigated by elevating buildings and providing a windproof envelope. Ground-level enclosures are designed to be sacrificial and non-structural so they can wash or blow away without imposing damage on the upper portions of the building, and only non-critical functions and equipment will be supported within them. Design features that integrate survivability with sustainability include: orientation of building axis; integral shading from direct summer sunlight; light wells; photovoltaic arrays; collection of rainwater and air conditioning condensate for use in landscape irrigation; reduced impervious cover; xeriscaping and indigenous plants; recycling of waste heat from air conditioning systems; roofing system that reflects light and heat; long life, low maintenance stainless steel, high-tensile vinyl, hard-anodized aluminum and hot-dipped galvanized mountings throughout; chloride-resistant concrete; reduced visual impact; recycling of construction materials.

Dehydration of prawns in tunnel dryers

This paper deals with the dehydration of prawns in a tunnel dryer. Conditions required to produce an end-product of desired colour, shape and texture as well as good reconstitution and organoleptic properties which are not obtained in the normal hot air drying, have been worked out. An initial temperature and relative humidity of 90°C. and 85%-90% respectively and an air velocity not more than 1 metre/second are the essential conditions required. Both temperature and relative humidity are to be reduced to 70°C and 40% respectively after about an hour's operation, till the drying is complete. Flavour of the reconstituted product is close to that of the fresh cooked prawns and the texture is judged to be soft. Drying time required to reduce the moisture content of fresh prawns to 15% level is about 7 hours compared to 6-7 hours in normal hot air drying and more than 36 hours in sun-drying.

An accelerated method of hot air drying of fish

The effects of temperature and relative humidity on the rate of drying of split open fish and salted fish in a tunnel dryer have been studied at a constant air velocity. By a judicious combination of these two, the rate of drying could be considerably accelerated, 10 to 12 hours only being required for drying to moisture levels below 30% in the case of mackerel, lactarius, otolithes and kilimeen (Nemipterus japonicus)

Studies on the storage behaviour of laminated and commercial Bombay duck

A modified method for the preparation of laminated Bombay duck is presented. Investigation was carried out to find out an effective chemical to control the discoloration of dried laminated Bombay duck. Among various chemicals tried, NDGA and BHT were found to have considerably retarded the discoloration and extended the storage life of the product. Attempt was also made to suggest the optimum humidity level for the proper storage of the commercially dried fish. It was found that a level of about 65% R. H. provided maximum storage life to commercial product.

Aquacrops of Darbhanga District in north Bihar and their commercial significance

Darbhanga district in North Bihar is characterised by thick alluvial soil, moderately good rainfall, high humidity, ample sunshine and numerous water resources in the form of perennial rivers, tributaries, streams, lakes, ponds, pools and puddles. The aquacrops of this district include several species of commercially important fishes, aquatic cash crops such as makhana (Euryale ferox), singhara (Trapa spp.), lotus, lilly, Khubi etc. and molluscs. This paper highlights the commercial significance of these aquacrops and offers suggestions for their sustained development.

Toxigenic molds on fish feeds-1: impact of climatic change

The present communication is a survey report carried out to assess the incidence of toxic mycoflora on seven types of agriculture products/by products incorporated during fish culture as supplementary dietary items. Samples were obtained from various sources at Darbhanga, Madhubani and Samashtipur districts during summer, winter and monsoon months. Out of the total 1774 samples, only 894 appeared to be fresh visually reflecting average incidence of contamination around 46.6%. However, the apparently fresh samples, when subjected to culture, 26.9% of them were found to be contaminated. Thus, degree of fungal spoilage in feed ingredients in parts of north Bihar appears to be significantly high (73.5%). The present study illustrates the facts with special reference to Aspergillus flavus, A. parasiticus (elaborating aflatoxins) A. ochraceous, Penicilium viradicatuin (elaborating ochratoxins) and A. versicolor (elaborating sterigmatocystin). The other strains already known for their toxigenic potentials that appeared on the present substrates included A. niger, A. fumigatus, A. candidus, P. islandicum, Rhizopus spp. and Mucur spp. Studies indicate that the prevalent climatic factors like temperature and relative humidity facilitate a congenial condition almost all through the year and in particular during summer and monsoon months. But water content of the substrates is a vital factor that further accelerates the pace of mycobial spoilage. A thorough sun-drying of the agricultural commodities before prolonged storage to bring water content below the "low risk limit" may significantly reduce the incidence of molds.

Results of the Austrian-Ceylonese hydrobiological mission 1970 of the 1st Zoological Institute of the University of Vienna (Austria) and the Department of Zoology of the Vidyalankara University of Ceylon, Kelaniya. Pt. 4. List of reptilia and amphibia collected in the mountains of south-west Ceylon, with notes on finding localities

Sri Lanka is a comparatively small island (65.584 km²) within the equatorial belt of calms. There are only slight seasonal variations in temperature, air humidity and day length. A description is given of the amphibian and reptile material brought back from the Austrian Indo-Pacific expedition, 1970-71. Some notes on the habitat of the animals are included.

Physics in fish processing technology

To design, develop and put into operation an equipment either to increase the productivity or to improve the existing technique to obtain a better quality of the product, the fishery engineer/scientist should have a comprehensive knowledge of fundamental principles involved in the process. Many a technique in fish processing technology, whether it applies to freezing, dehydration or canning, involves always a type of heat transfer, which is dependent to a certain extent on the external physical parameters like temperature. humidity, pressure, air flow etc. and also on the thermodynamic properties of fish muscle in the temperature ranges encountered. Similarly informations on other physical values like dielectric constant and dielectric loss in the design of quick trawlers and in quality assessment of frozen/iced fish, refractive index and viscosity in the measurement of the saturation and polymerisation of fish oils and shear strength in the judgement of textural qualities of cooked fish are also equally important.

Packaging and storage studies of dried lizard fish

Packaging and storage studies of salted and dried lizard fish (Saurida sp.) have been conducted using different synthetic films like low density polyethylene (LDPE) of different gauges, high density polyethylene (HDPE) of 200 gauge, polyvinylidene chloride (PVDC) coated 400 MXXT cellophane, 100 gauge polypropylene (PP) and paper laminate of 100 gauge polythene. The films found most effective in the preliminary studies were subsequently used for packaging and storage of dried fish at atmospheric and lower temperature and humidity conditions for confirming their suitability under these conditions. Polyethylene films of higher gauges showed better results under both sets of conditions. PVDC coated cellophane film also performed satisfactorily under the latter conditions which under the former condition got easily attacked by insects. Lower temperature and humidity conditions in general enhanced the storage life of the dried product.

Comparative feature on design, construction and installation of three different model of low cost solar tunnel dryers

The study was conducted in collaboration with the ECFC project of the FAO (BGD/97/017) in Cox's Bazar to develop a low cost solar tunnel dryer for the production of high quality marine dried fish. The study areas were Kutubdiapara, Maheshkhali and Shahparirdip under Cox's Bazar district. Three different models of low cost solar dryer were constructed with locally available materials such as bamboo, wood, bamboo mat, hemp, canvas, wire, nails, rope, tin, polythene and net. Size of the dryers were: 20x4x3 ft ; 30x3x3 ft and 65x3x3 ft with the costs of Tk. 3060, 3530, 9600 for dryer 1, 2 and 3, respectively having different models. The drying capacities were 50, 150, 500 kg for dryer 1, 2 and 3 respectively. The average temperature range inside the dryers were 29-43°C, 34-51°C and 37-57°C for dryer 1, 2 and 3 respectively as recorded at 8:30h to 16:30h. The relative humidity were in the ranges of 22-42%, 27-39% and 24-41 % in dryer 1, 2 and 3 respectively. The fish samples used were Bombay duck, Silver Jew fish and Ribbon fish. The total drying time was in the range of 30-42, 28-38 and 24-34 hours to reach the moisture content of 12.3-14.5, 11.8-14.3, and 11.6-14.1% in dryer 1, 2 and 3 respectively. Among these three fish samples the drying was faster in Silver Jew fish followed by Bombay duck and Ribbon fish in all the three dryer.

Production of quality dried small indigenous fish species products using low cost solar tunnel drier

A low cost solar drier was constructed using locally available materials. The size of the drier was 20x3.6x3 having drying capacity of 80 kg of SIS (w/w). Optimization of moisture content was observed for mola, dhela, chapila, chanda and puti at temperature ranges between 40-45°C and 50-55°C in solar tunnel drier. There was little or no change in moisture content at temperature below 40°C during the first 3 hours. Then the moisture content declined gradually with the increase of drying period. On the other hand, at temperature between 50-55°C, moisture content started to decline after 2 hours of drying. The moisture content of the sample reached at about 16% after 26 hours of sun drying at 40-45°C and 20 hours at 50-55°C. The optimum temperature for producing high quality dried products was 45-50°C in solar tunnel drier. The temperature and relative humidity outside and inside the dryers (with fish) at various locations were recorded from 8.00am to 4.00pm. The normal atmospheric ambient temperature was recorded in the range of 25-37°C from at 8:00am to 4:00pm. During the same period the atmospheric relative humidity recorded was in the range of 30-58%. On the other hand, the maximum temperature inside the dryers was recorded in the range of 28-65°C. The lowest temperature recorded was 28°C in the morning and at 13.00pm the highest temperature 65°C was recorded. The maximum relative humidity 58% found in the afternoon and minimum of 28% at noon. There was inverse relationship between temperature intensity of sunshine and humidity which decreased as sunshine increased. In total, it took around 26 hours of drying to reduce the moisture level to about 16%.

Study on the sustainability of FPC produced from Kilka (Clupeonella engrauliformis, C. grimmi and C. cultriventris) in two vacuum packaging and modified atmosphere packaging at different environmental factors

Fish protein concentrate (FPC) is a healthy, sustainable and high nutritive product which sanitized produced from fishes in which, protein and other nutrients are more concentrated than in fresh fishes. The aim of this research is to study on the sustainability of FPC produced from Kilka (Clupeonella engrauliformis , C. grimmi and C. cultriventris) in two Vaccum Packaging and Modified Atmosphere Packaging at different environmental factors during six months. In our study the analysis of FPC protein showed 91.2%, lipid: 0.5%, ash: 3.6%, moisture: 2.3%, Total Volatile Nitrogen: 10 ml/100gr and peroxide: 5meq/kg. Amino acids and fatty acids were also determined. Bacteria and Fungi were lower than 1000 colony. Samples are kept in different condition of temperature (5, 20 and 35 degree centigrade), humidity (25, 40 and 90 percent) and light and dark environment in six month. Lipid rate in FPC after 6 months in VP and MAP (60% C02, 30 % N2 and 10% O2), packages was decreased but was not significant (P>0.05). It was also detected that increase temperature lead to more decrease in lipid content. Protein rate of FPC was decreased from 91.2% to 73.6% during six months at 35°C in VP Package and from 91.2% to 69.4% in MAP package. These changes were significant (P<0.05). TVN and PV rate in FPC after 6 months in VP and MAP packages was increased but was significant (P<0.05). Amino acids and fatty acids were also determined. But more changes in MAP packages was detected.

Quantative and qualitive identification of the fatty acids in the mullet (Liza aurata), sever juga (Acipenser stellatus) and Persian sturgeon (A. persicus), considering of cold storing effects on them

At the fishing season, in 2000, samples of species persian sturgeon (A. persicus), Severjuga (A. stellatus) and Mullet (L. aurata), were caught from the southern coasts of Caspian Sea and were freezes and preserved in the cold storage for one year They have also become biometery. The tissue's fillet were identified in order to determined the Fatty Acids. This was done during one year, frequently, fresh, two weeks after freezing and then monthly, respectively. So, after the extraction of lipids from the tissues and methylation, was injected to the gas-liquid Chromatography. After calibration, identified Fatty Acids were compared with standards according to their Retention Times. Peroxid value, lipid content and humidity were controlled. The unsaturated Fatty acids had The most amount, and a plenty of Polyunsaturated Fatty acids (PUFA) were observed, so that linoleic (C18:2), a-linolenic (C18:3), Arashidonic (C20:4), EPA (C20:5) and DHA (C22:6) Fatty acids had high amounts. The w-3, PUFA were more in comparison with w-6. The effects of freezing and cold storing on the fish fatty acids , were evaluated by the statistical tests , like SPSS, Tukey, Homogenous and Anova, and showed that in some species, a group of Fatty acids, specially PUFA, had some variation. The peroxide value that indicates the lipid deterioration, increased during toring. So, the best term if preserving in the cold storage, were determined and their Nutrition value and Medical applications due to their consumption were investigated.