Dense, efficient chip-to-chip communication at the extremes of computing

The scalability of CMOS technology has driven computation into a diverse range of applications across the power consumption, performance and size spectra. Communication is a necessary adjunct to computation, and whether this is to push data from node-to-node in a high-performance computing cluster or from the receiver of wireless link to a neural stimulator in a biomedical implant, interconnect can take up a significant portion of the overall system power budget. Although a single interconnect methodology cannot address such a broad range of systems efficiently, there are a number of key design concepts that enable good interconnect design in the age of highly-scaled CMOS: an emphasis on highly-digital approaches to solving ‘analog’ problems, hardware sharing between links as well as between different functions (such as equalization and synchronization) in the same link, and adaptive hardware that changes its operating parameters to mitigate not only variation in the fabrication of the link, but also link conditions that change over time. These concepts are demonstrated through the use of two design examples, at the extremes of the power and performance spectra.

A novel all-digital clock and data recovery technique for high-performance, high density interconnect has been developed. Two independently adjustable clock phases are generated from a delay line calibrated to 2 UI. One clock phase is placed in the middle of the eye to recover the data, while the other is swept across the delay line. The samples produced by the two clocks are compared to generate eye information, which is used to determine the best phase for data recovery. The functions of the two clocks are swapped after the data phase is updated; this ping-pong action allows an infinite delay range without the use of a PLL or DLL. The scheme's generalized sampling and retiming architecture is used in a sharing technique that saves power and area in high-density interconnect. The eye information generated is also useful for tuning an adaptive equalizer, circumventing the need for dedicated adaptation hardware.

On the other side of the performance/power spectra, a capacitive proximity interconnect has been developed to support 3D integration of biomedical implants. In order to integrate more functionality while staying within size limits, implant electronics can be embedded onto a foldable parylene (‘origami’) substrate. Many of the ICs in an origami implant will be placed face-to-face with each other, so wireless proximity interconnect can be used to increase communication density while decreasing implant size, as well as facilitate a modular approach to implant design, where pre-fabricated parylene-and-IC modules are assembled together on-demand to make custom implants. Such an interconnect needs to be able to sense and adapt to changes in alignment. The proposed array uses a TDC-like structure to realize both communication and alignment sensing within the same set of plates, increasing communication density and eliminating the need to infer link quality from a separate alignment block. In order to distinguish the communication plates from the nearby ground plane, a stimulus is applied to the transmitter plate, which is rectified at the receiver to bias a delay generation block. This delay is in turn converted into a digital word using a TDC, providing alignment information.

Randomness-efficient curve sampling

Curve samplers are sampling algorithms that proceed by viewing the domain as a vector space over a finite field, and randomly picking a low-degree curve in it as the sample. Curve samplers exhibit a nice property besides the sampling property: the restriction of low-degree polynomials over the domain to the sampled curve is still low-degree. This property is often used in combination with the sampling property and has found many applications, including PCP constructions, local decoding of codes, and algebraic PRG constructions.

The randomness complexity of curve samplers is a crucial parameter for its applications. It is known that (non-explicit) curve samplers using O(log N + log(1/δ)) random bits exist, where N is the domain size and δ is the confidence error. The question of explicitly constructing randomness-efficient curve samplers was first raised in [TU06] where they obtained curve samplers with near-optimal randomness complexity.

In this thesis, we present an explicit construction of low-degree curve samplers with optimal randomness complexity (up to a constant factor) that sample curves of degree (m log_q(1/δ))^O(1) in F_q^m. Our construction is a delicate combination of several components, including extractor machinery, limited independence, iterated sampling, and list-recoverable codes.

Double injection: high frequency noise and temperature dependence

Noise measurements from 140°K to 350°K ambient temperature and between 10kHz and 22MHz performed on a double injection silicon diode as a function of operating point indicate that the high frequency noise depends linearly on the ambient temperature T and on the differential conductance g measured at the same frequency. The noise is represented quantitatively by〈i^2〉 = α•4kTgΔf. A new interpretation demands Nyquist noise with α ≡ 1 in these devices at high frequencies. This is in accord with an equivalent circuit derived for the double injection process. The effects of diode geometry on the static I-V characteristic as well as on the ac properties are illustrated. Investigation of the temperature dependence of double injection yields measurements of the temperature variation of the common high-level lifetime τ(τ ∝ T^2), the hole conductivity mobility µ_p (µ_p ∝ T^(-2.18)) and the electron conductivity mobility µ_n(µ_n ∝ T^(-1.75)).

Self-healing Techniques for RF and mm-Wave Transmitters and Receivers

With continuing advances in CMOS technology, feature sizes of modern Silicon chip-sets have gone down drastically over the past decade. In addition to desktops and laptop processors, a vast majority of these chips are also being deployed in mobile communication devices like smart-phones and tablets, where multiple radio-frequency integrated circuits (RFICs) must be integrated into one device to cater to a wide variety of applications such as Wi-Fi, Bluetooth, NFC, wireless charging, etc. While a small feature size enables higher integration levels leading to billions of transistors co-existing on a single chip, it also makes these Silicon ICs more susceptible to variations. A part of these variations can be attributed to the manufacturing process itself, particularly due to the stringent dimensional tolerances associated with the lithographic steps in modern processes. Additionally, RF or millimeter-wave communication chip-sets are subject to another type of variation caused by dynamic changes in the operating environment. Another bottleneck in the development of high performance RF/mm-wave Silicon ICs is the lack of accurate analog/high-frequency models in nanometer CMOS processes. This can be primarily attributed to the fact that most cutting edge processes are geared towards digital system implementation and as such there is little model-to-hardware correlation at RF frequencies.

All these issues have significantly degraded yield of high performance mm-wave and RF CMOS systems which often require multiple trial-and-error based Silicon validations, thereby incurring additional production costs. This dissertation proposes a low overhead technique which attempts to counter the detrimental effects of these variations, thereby improving both performance and yield of chips post fabrication in a systematic way. The key idea behind this approach is to dynamically sense the performance of the system, identify when a problem has occurred, and then actuate it back to its desired performance level through an intelligent on-chip optimization algorithm. We term this technique as self-healing drawing inspiration from nature's own way of healing the body against adverse environmental effects. To effectively demonstrate the efficacy of self-healing in CMOS systems, several representative examples are designed, fabricated, and measured against a variety of operating conditions.

We demonstrate a high-power mm-wave segmented power mixer array based transmitter architecture that is capable of generating high-speed and non-constant envelope modulations at higher efficiencies compared to existing conventional designs. We then incorporate several sensors and actuators into the design and demonstrate closed-loop healing against a wide variety of non-ideal operating conditions. We also demonstrate fully-integrated self-healing in the context of another mm-wave power amplifier, where measurements were performed across several chips, showing significant improvements in performance as well as reduced variability in the presence of process variations and load impedance mismatch, as well as catastrophic transistor failure. Finally, on the receiver side, a closed-loop self-healing phase synthesis scheme is demonstrated in conjunction with a wide-band voltage controlled oscillator to generate phase shifter local oscillator (LO) signals for a phased array receiver. The system is shown to heal against non-idealities in the LO signal generation and distribution, significantly reducing phase errors across a wide range of frequencies.

Gauge Invariant Spectral Cauchy Characteristic Extraction of Gravitational Waves in Computational General Relativity

We present a complete system for Spectral Cauchy characteristic extraction (Spectral CCE). Implemented in C++ within the Spectral Einstein Code (SpEC), the method employs numerous innovative algorithms to efficiently calculate the Bondi strain, news, and flux.

Spectral CCE was envisioned to ensure physically accurate gravitational wave-forms computed for the Laser Interferometer Gravitational wave Observatory (LIGO) and similar experiments, while working toward a template bank with more than a thousand waveforms to span the binary black hole (BBH) problem’s seven-dimensional parameter space.

The Bondi strain, news, and flux are physical quantities central to efforts to understand and detect astrophysical gravitational wave sources within the Simulations of eXtreme Spacetime (SXS) collaboration, with the ultimate aim of providing the first strong field probe of the Einstein field equation.

In a series of included papers, we demonstrate stability, convergence, and gauge invariance. We also demonstrate agreement between Spectral CCE and the legacy Pitt null code, while achieving a factor of 200 improvement in computational efficiency.

Spectral CCE represents a significant computational advance. It is the foundation upon which further capability will be built, specifically enabling the complete calculation of junk-free, gauge-free, and physically valid waveform data on the fly within SpEC.

Performance calculations of new propellant systems

The purpose of this thesis is to investigate the effect on performance and chamber temperature of adding hydrogen to a propellant system. The systems investigated are:

(1) RFNA-Aniline

(2) Nitromethane

(3) Anhydrous hydrazene-liquid oxygen

Since a systematic investigation of the performance parameters of the RFNA-Aniline system over a wide range of mixture ratios has never been made, it was decided to make these calculations, in addition to the investigations stated above.

The results of the calculations can best be summarized by a study of the figures at the end of the thesis. A few generalizations can be made. The effect of adding hydrogen in small quantities to a high temperature system is to increase the performance considerably without too much change in the chamber temperature. As more hydrogen is added, the percentage increase in performance. If hydrogen is added in large quantities, both the performance curve (effective exhaust velocity) and the chamber temperature curve flatten out.

The behavior discussed above is characteristic of hot propellant systems such as RFNA-Aniline and anhydrous hydrazene. In a low temperature system, such as nitromethane, the effect is quite different. The addition of hydrogen in small quantities causes a rapid decrease in chamber temperature, but the increase in performance is considerably less on a percentage basis. As more hydrogen is added the changes in performance and chamber temperature are almost linear.

Estimation of catalyst activity profiles and deactivation parameters from reactor operating data with applications to naphtha reforming

Techniques are developed for estimating activity profiles in fixed bed reactors and catalyst deactivation parameters from operating reactor data. These techniques are applicable, in general, to most industrial catalytic processes. The catalytic reforming of naphthas is taken as a broad example to illustrate the estimation schemes and to signify the physical meaning of the kinetic parameters of the estimation equations. The work is described in two parts. Part I deals with the modeling of kinetic rate expressions and the derivation of the working equations for estimation. Part II concentrates on developing various estimation techniques.

Part I: The reactions used to describe naphtha reforming are dehydrogenation and dehydroisomerization of cycloparaffins; isomerization, dehydrocyclization and hydrocracking of paraffins; and the catalyst deactivation reactions, namely coking on alumina sites and sintering of platinum crystallites. The rate expressions for the above reactions are formulated, and the effects of transport limitations on the overall reaction rates are discussed in the appendices. Moreover, various types of interaction between the metallic and acidic active centers of reforming catalysts are discussed as characterizing the different types of reforming reactions.

Part II: In catalytic reactor operation, the activity distribution along the reactor determines the kinetics of the main reaction and is needed for predicting the effect of changes in the feed state and the operating conditions on the reactor output. In the case of a monofunctional catalyst and of bifunctional catalysts in limiting conditions, the cumulative activity is sufficient for predicting steady reactor output. The estimation of this cumulative activity can be carried out easily from measurements at the reactor exit. For a general bifunctional catalytic system, the detailed activity distribution is needed for describing the reactor operation, and some approximation must be made to obtain practicable estimation schemes. This is accomplished by parametrization techniques using measurements at a few points along the reactor. Such parametrization techniques are illustrated numerically with a simplified model of naphtha reforming.

To determine long term catalyst utilization and regeneration policies, it is necessary to estimate catalyst deactivation parameters from the the current operating data. For a first order deactivation model with a monofunctional catalyst or with a bifunctional catalyst in special limiting circumstances, analytical techniques are presented to transform the partial differential equations to ordinary differential equations which admit more feasible estimation schemes. Numerical examples include the catalytic oxidation of butene to butadiene and a simplified model of naphtha reforming. For a general bifunctional system or in the case of a monofunctional catalyst subject to general power law deactivation, the estimation can only be accomplished approximately. The basic feature of an appropriate estimation scheme involves approximating the activity profile by certain polynomials and then estimating the deactivation parameters from the integrated form of the deactivation equation by regression techniques. Different bifunctional systems must be treated by different estimation algorithms, which are illustrated by several cases of naphtha reforming with different feed or catalyst composition.