Parylene-C as a new piezoelectric material

The goal of this thesis is to develop a proper microelectromechanical systems (MEMS) process to manufacture piezoelectric Parylene-C (PA-C), which is famous for its chemical inertness, mechanical and thermal properties and electrical insulation. Furthermore, piezoelectric PA-C is used to build miniature, inexpensive, non-biased piezoelectric microphones.

These piezoelectric PA-C MEMS microphones are to be used in any application where a conventional piezoelectric and electret microphone can be used, such as in cell phones and hearing aids. However, they have the advantage of a simplified fabrication process compared with existing technology. In addition, as a piezoelectric polymer, PA-C has varieties of applications due to its low dielectric constant, low elastic stiffness, low density, high voltage sensitivity, high temperature stability and low acoustic and mechanical impedance. Furthermore, PA-C is an FDA approved biocompatible material and is able to maintain operate at a high temperature.

To accomplish piezoelectric PA-C, a MEMS-compatible poling technology has been developed. The PA-C film is poled by applying electrical field during heating. The piezoelectric coefficient, -3.75pC/N, is obtained without film stretching.

The millimeter-scale piezoelectric PA-C microphone is fabricated with an in-plane spiral arrangement of two electrodes. The dynamic range is from less than 30 dB to above 110 dB SPL (referenced 20 µPa) and the open-circuit sensitivities are from 0.001 – 0.11 mV/Pa over a frequency range of 1 - 10 kHz. The total harmonic distortion of the device is less than 20% at 110 dB SPL and 1 kHz.

Sterochemically modified polyamides for recognition in the minor groove of DNA

The design of synthetic molecules that recognize specific sequences of DNA is an ongoing challenge in molecular medicine. Cell-permeable small molecules targeting predetermined DNA sequences offer a potential approach for offsetting the abnormal effects of misregulated gene-expression. Over the past twenty years, Professor Peter B. Dervan has developed a set of pairing rules for the rational design of minor groove binding polyamides containing pyrrole (Py), imidazole (Im), and hydroxypyrrole (Hp). Polyamides have illustrated the capability to permeate cells and inhibit transcription of specific genes in vivo. This provides impetus to identify structural elements that expand the repetoire of polyamide motifs with recognition properties comparable to naturally occurring DNA binding proteins. Through the introduction of chiral amino acids, we have developed chiral polyamides with stereochemically regulated binding characteristics. In addition, chiral substituents have facilitated the development of new polyamide motifs that broaden binding site sizes targetable by this class of ligands.

High pressure states in condensed matter: I. High pressure behavior of the iron-sulphur system with applications to the earth's core. II. Empirical equation of state for organic compounds at high pressures

Part I:

The earth's core is generally accepted to be composed primarily of iron, with an admixture of other elements. Because the outer core is observed not to transmit shear waves at seismic frequencies, it is known to be liquid or primarily liquid. A new equation of state is presented for liquid iron, in the form of parameters for the 4th order Birch-Murnaghan and Mie-Grüneisen equations of state. The parameters were constrained by a set of values for numerous properties compiled from the literature. A detailed theoretical model is used to constrain the P-T behavior of the heat capacity, based on recent advances in the understanding of the interatomic potentials for transition metals. At the reference pressure of 10⁵ Pa and temperature of 1811 K (the normal melting point of Fe), the parameters are: ρ = 7037 kg/m³, K_S0 = 110 GPa, K_S' = 4.53, K_S" = -.0337 GPa-1, and γ = 2.8, with γ α ρ^-1.17. Comparison of the properties predicted by this model with the earth model PREM indicates that the outer core is 8 to 10 % less dense than pure liquid Fe at the same conditions. The inner core is also found to be 3 to 5% less dense than pure liquid Fe, supporting the idea of a partially molten inner core. The density deficit of the outer core implies that the elements dissolved in the liquid Fe are predominantly of lower atomic weight than Fe. Of the candidate light elements favored by researchers, only sulfur readily dissolves into Fe at low pressure, which means that this element was almost certainly concentrated in the core at early times. New melting data are presented for FeS and FeS₂ which indicate that the FeS₂ is the S-hearing liquidus solid phase at inner core pressures. Consideration of the requirement that the inner core boundary be observable by seismological means and the freezing behavior of solutions leads to the possibility that the outer core may contain a significant fraction of solid material. It is found that convection in the outer core is not hindered if the solid particles are entrained in the fluid flow. This model for a core of Fe and S admits temperatures in the range 3450K to 4200K at the top of the core. An all liquid Fe-S outer core would require a temperature of about 4900 K at the top of the core.

Part II.

The abundance of uses for organic compounds in the modern world results in many applications in which these materials are subjected to high pressures. This leads to the desire to be able to describe the behavior of these materials under such conditions. Unfortunately, the number of compounds is much greater than the number of experimental data available for many of the important properties. In the past, one approach that has worked well is the calculation of appropriate properties by summing the contributions from the organic functional groups making up molecules of the compounds in question. A new set of group contributions for the molar volume, volume thermal expansivity, heat capacity, and the Rao function is presented for functional groups containing C, H, and O. This set is, in most cases, limited in application to low molecular liquids. A new technique for the calculation of the pressure derivative of the bulk modulus is also presented. Comparison with data indicates that the presented technique works very well for most low molecular hydrocarbon liquids and somewhat less well for oxygen-bearing compounds. A similar comparison of previous results for polymers indicates that the existing tabulations of group contributions for this class of materials is in need of revision. There is also evidence that the Rao function contributions for polymers and low molecular compounds are somewhat different.

Sensing and Actuation from Biology to Electronics

We introduce an in vitro diagnostic magnetic biosensing platform for immunoassay and nucleic acid detection. The platform has key characteristics for a point-of-use (POU) diagnostic: portability, low-power consumption, low cost, and multiplexing capability. As a demonstration of capabilities, we use this platform for the room temperature, amplification-free detection of a 31 bp DNA oligomer and interferon-gamma (a protein relevant for tuberculosis diagnosis). Reliable assay measurements down to 100 pM for the DNA and 1 pM for the protein are demonstrated. We introduce a novel "magnetic freezing" technique for baseline measurement elimination and to enable spatial multiplexing. We have created a general protocol for adapting integrated circuit (IC) sensors to any of hundreds of commercially available immunoassay kits and custom designed DNA sequences.

We also introduce a method for immunotherapy treatment of malignant gliomas. We utilize leukocytes internalized with immunostimulatory nanoparticle-oligonucleotide conjugates to localize and retain immune cells near the tumor site. As a proof-of-principle, we develop a novel cell imaging and incubation chamber for in vitro magnetic motility experiments. We use the apparatus to demonstrate the controlled movement of magnetically loaded THP-1 leukocytes.

Finally, we introduce an IC transmitter and power ampli er (PA) that utilizes electronic digital infrastructure, sensors, and actuators to self-heal and adapt to process, dynamic, and environmental variation. Traditional IC design has achieved incredible degrees of reliability by ensuring that billions of transistors on a single IC die are all simultaneously functional. Reliability becomes increasingly difficult as the size of a transistor shrinks. Self-healing can mitigate these variations.

Bicyclo[3.2.0]hepta-1,4,6-triene: synthesis, thermal rearrangement, and anion formation

In order to determine the properties of the bicycloheptatrienyl anion (Ia) (predicted to be conjugatively stabilized by Hückel Molecular Orbital Theory) the neutral precursor, bicyclo[3. 2. 0] hepta-1, 4, 6-triene (I) was prepared by the following route.

Reaction of I with potassium-t-butoxide, potassium, or lithium dicyclohexylamide gave anion Ia in very low yield. Reprotonation of I was found to occur solely at the 1 or 5 position to give triene II, isolated as to its dimers.

A study of the acidity of I and of other conjugated hydrocarbons by means of ion cyclotron resonance spectroscopy resulted in determination of the following order of relative acidities:

H₂S ˃ C₅H₆ ˃ CH₃NO₂ ˃ 1, 4- C₅H₈ ˃ I ˃ C₂H₅OH ˃ H₂O; cyclo-C₇H₈ ˃ C₂ H₅OH; фCH₃ ˃ CH₃OH

In addition, limits for the proton affinities of the conjugate bases were determined:

350 kcal/mole ˂ PA(C₅ H₅^-) ˂ 360 kcal/mole

362 kcal/mole ˂ PA(C₅H₇^-, Ia, cyclo-C₇H₇^-) ˂ 377 kcal/mole PA(фCH₂^-) ˂ 385 kcal/mole

Gas phase kinetics of the trans-XVIII to I transformation gave the following activation parameters: E_a = 43.0 kcal/mole, log A = 15.53 and ∆S^ǂ (220°) = 9.6 cu. The results were interpreted as indicating initial 1,2 bond cleavage to give the 1,3-diradical which closed to I. Similar studies on cis-XVIII gave results consistent with a surface component to the reaction (E_a = 22.7 kcal/mole; log A = 9.23, ∆S^ǂ (119°) = -18.9 eu).

The low pressure (0.01 to 1 torr) pyrolysis of trans-XVIII gave in addition to I, fulvenallene (LV), ethynylcyclopentadiene (LVI) and heptafulvalene (LVII). The relative ratios of the C₇H₆ isomers were found to be dependent upon temperature and pressure, higher relative pressure and lower temperatures favoring formation of I. The results were found to be consistent with the intermediacy of vibrationally excited I and subsequent reaction to give LV and LVI.

Investigations of nonhistone chromosomal proteins

The major nonhistone chromosomal proteins (NHC proteins) are a group of 14-20 acidic proteins associated with DNA in eukaryotic chromatin. In comparisons by SDS gel electrophoresis (molecular weight sieving) one observes a high degree of homology among the NHC protein fractions of different tissues from a given species. Tissue-specific protein bands are also observed. The appearance of a new NHC protein, A, in the NHC proteins of rat liver stimulated to divide by partial hepatectomy and of rat ascites cells suggests that this protein may play a role in preparing the cell for division. The NHC proteins of the same tissue from different species are also very similar. Quantitative but not qualitative changes in the NHC proteins of rat uterus are observed on stimulation (in vivo) with estrogen. These observations suggest that the major NHC proteins play a general role in chromatin structure and the regulation of genome expression; several may be enzymes of nucleic acid and histone metabolism and/or structural proteins analogous to histones. One such enzyme, a protease which readily and preferentially degrades histones, can be extracted from chromatin with 0.7 N NaCl.

Although the NHC proteins readily aggregate, they can be separated from histone and fractionated by ion exchange chromatography on Sephadex SE C-25 resin in 10 M urea-25% formic acid (pH 2.5). Following further purification, four fractions of NHC protein are obtained; two of these are single purified proteins, and the other two contain 4-6 and 4-7 different proteins. These NHC proteins show a ratio of acidic to basic amino acids from 2.7 to 1.2 and isoelectric points from apparently less than 3.7 to 8.0. These isolated fractions appear more soluble and easier to work with than any whole NHC protein preparation.