Diffusion in glassy polymers

Fluid diffusion in glassy polymers proceeds in ways that are not explained by the standard diffusion model. Although the reasons for the anomalous effects are not known, much of the observed behavior is attributed to the long times that polymers below their glass transition temperature take to adjust to changes in their condition. The slow internal relaxations of the polymer chains ensure that the material properties are history-dependent, and also allow both local inhomogeneities and differential swelling to occur. Two models are developed in this thesis with the intent of accounting for these effects in the diffusion process.

In Part I, a model is developed to account for both the history dependence of the glassy polymer, and the dual sorption which occurs when gas molecules are immobilized by the local heterogeneities. A preliminary study of a special case of this model is conducted, showing the existence of travelling wave solutions and using perturbation techniques to investigate the effect of generalized diffusion mechanisms on their form. An integral averaging method is used to estimate the penetrant front position.

In Part II, a model is developed for particle diffusion along with displacements in isotropic viscoelastic materials. The nonlinear dependence of the materials on the fluid concentration is taken into account, while pure displacements are assumed to remain in the range of linear viscoelasticity. A fairly general model is obtained for three-dimensional irrotational movements, with the development of the model being based on the assumptions of irreversible thermodynamics. With the help of some dimensional analysis, this model is simplified to a version which is proposed to be studied for Case II behavior.

Digested sludge: delineation and modeling for ocean disposal

Experimental work was performed to delineate the system of digested sludge particles and associated trace metals and also to measure the interactions of sludge with seawater. Particle-size and particle number distributions were measured with a Coulter Counter. Number counts in excess of 10¹² particles per liter were found in both the City of Los Angeles Hyperion mesophilic digested sludge and the Los Angeles County Sanitation Districts (LACSD) digested primary sludge. More than 90 percent of the particles had diameters less than 10 microns.

Total and dissolved trace metals (Ag, Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) were measured in LACSD sludge. Manganese was the only metal whose dissolved fraction exceeded one percent of the total metal. Sedimentation experiments for several dilutions of LACSD sludge in seawater showed that the sedimentation velocities of the sludge particles decreased as the dilution factor increased. A tenfold increase in dilution shifted the sedimentation velocity distribution by an order of magnitude. Chromium, Cu, Fe, Ni, Pb, and Zn were also followed during sedimentation. To a first approximation these metals behaved like the particles.

Solids and selected trace metals (Cr, Cu, Fe, Ni, Pb, and Zn) were monitored in oxic mixtures of both Hyperion and LACSD sludges for periods of 10 to 28 days. Less than 10 percent of the filterable solids dissolved or were oxidized. Only Ni was mobilized away from the particles. The majority of the mobilization was complete in less than one day.

The experimental data of this work were combined with oceanographic, biological, and geochemical information to propose and model the discharge of digested sludge to the San Pedro and Santa Monica Basins. A hydraulic computer simulation for a round buoyant jet in a density stratified medium showed that discharges of sludge effluent mixture at depths of 730 m would rise no more than 120 m. Initial jet mixing provided dilution estimates of 450 to 2600. Sedimentation analyses indicated that the solids would reach the sediments within 10 km of the point discharge.

Mass balances on the oxidizable chemical constituents in sludge indicated that the nearly anoxic waters of the basins would become wholly anoxic as a result of proposed discharges. From chemical-equilibrium computer modeling of the sludge digester and dilutions of sludge in anoxic seawater, it was predicted that the chemistry of all trace metals except Cr and Mn will be controlled by the precipitation of metal sulfide solids. This metal speciation held for dilutions up to 3000.

The net environmental impacts of this scheme should be salutary. The trace metals in the sludge should be immobilized in the anaerobic bottom sediments of the basins. Apparently no lifeforms higher than bacteria are there to be disrupted. The proposed deep-water discharges would remove the need for potentially expensive and energy-intensive land disposal alternatives and would end the discharge to the highly productive water near the ocean surface.

Functionalization of Si(111) surfaces and the formation of mixed monolayers for the covalent attachment of molecular catalysts in photoelectrochemical devices

The functionalization of silicon surfaces with molecular catalysts for proton reduction is an important part of the development of a solar-powered, water-splitting device for solar fuel formation. The covalent attachment of these catalysts to silicon without damaging the underlying electronic properties of silicon that make it a good photocathode has proven difficult. We report the formation of mixed monolayer-functionalized surfaces that incor- porate both methyl and vinylferrocenyl or vinylbipyridyl (vbpy) moieties. The silicon was functionalized using reaction conditions analogous to those of hydrosilylation, but instead of a H-terminated Si surface, a chlorine-terminated Si precursor surface was used to produce the linked vinyl-modified functional group. The functionalized surfaces were characterized by time-resolved photoconductivity decay, X-ray photoelectron spectroscopy (XPS), electro- chemical, and photoelectrochemical measurements. The functionalized Si surfaces were well passivated, exhibited high surface coverage and few remaining reactive Si atop sites, had a very low surface recombination velocity, and displayed little initial surface oxidation. The surfaces were stable toward atmospheric and electrochemical oxidation. The surface coverage of ferrocene or bipyridine was controllably varied from 0 up to 30% of a monolayer without loss of the underlying electronic properties of the silicon. Interfacial charge transfer to the attached ferrocene group was relatively rapid, and a photovoltage of 0.4 V was generated upon illumination of functionalized n-type silicon surfaces in CH₃CN. The immobilized bipyridine ligands bound transition metal ions, and thus enabled the assembly of metal complexes on the silicon surface. XPS studies demonstrated that [Cp∗Rh(vbpy)Cl]Cl, [Cp∗Ir(vbpy)Cl]Cl, and Ru(acac)₂vbpy were assembled on the surface. For the surface prepared with iridium, x-ray absorption spectroscopy at the Ir L_III edge showed an edge energy and post-edge features virtually identical to a powder sample of [Cp∗Ir(bipy)Cl]Cl (bipy is 2,2 ́-bipyridyl). Electrochemical studies on these surfaces confirmed that the assembled complexes were electrochemically active.