A study of the ^9 Be nucleus

The reaction ⁷Li(³He, p)⁹Be has been used to measure excitations and intrinsic widths of levels in ⁹Be below the ⁷Li + d threshold. Previously unreported levels have been found at excitations of (13.78 ± .03) MeV and (16.671 ± .008) MeV with widths of (590 ± 60) keV and (41 ± 4) keV respectively. Two overlapping levels have been found at (11.81 ± .02) MeV and (11.29 ± .03) MeV with widths of (400 ± 30) keV and (620 ± 70) keV respectively. Branching ratios from ⁹Be levels populated in this reaction to the ground and first excited states of ⁸Be have been measured by observing the associated protons in coincidence with the decay neutrons. Branching ratios were found to be:

Excitation in ⁹Be .... Branching Ratio.......... Final Nucleus.........

(MeV) .......................... (percent) .....................................

.. 2.43 ........................... 7.5 ± 1.5 .............. ⁸Be(g.s.)

.. 3.03 ........................... 87 ± 13......................................

.. 4.65 ........................... 13 ± 4.......................................

.. 6.76 .............................. ≤ 2 ......................................

.. 11.29 ...............................≤ 2 ......................................

.. 11.81 ...............................≤ 3 ......................................

.. 6.76 ........................... .41 ≤ B.R. ≤ .69 ....... ⁸Be(2⁺)

.. 11.29 ........................... 14 ± 4 .......................................

.. 11.81 ........................... 12 ± 4 .......................................

Corresponding reduced widths for neutron emission are calculated and a comparison of the results with the expectations of current nuclear models is made. In particular the measured branching ratio to ⁸Be(g.s.) from ⁹Be(2.43 MeV) corresponds to an f-wave reduced with θ²_f = 2.1 x 10^-2, in units of ħ²/mR², with R = 4.35 fm. A comparison of this value with that predicted by a Nilsson model calculation, in which ⁹Be is taken to be a deformed nucleus, is discussed. The measured value for θ²_f is found to be consistent with that expected on the basis of measured E2-transition rates between rotational levels in ⁹Be.

Part I. Efforts directed towards the total synthesis of shionone. Part II. Conversion of estrone to androst-4-EN-3-ONE: a new method for activating the C-9 and C-10 positions of estrogenic steroids for substitution

Part I: An approach to the total synthesis of the triterpene shionone is described, which proceeds through the tetracyclic ketone i. The shionone side chain has been attached to this key intermediate in 5 steps, affording the olefin 2 in 29% yield. A method for the stereo-specific introduction of the angular methyl group at C-5 of shionone has been developed on a model system. The attempted utilization of this method to convert olefin 2 into shionone is described.

Part II: A method has been developed for activating the C-9 and C-10 positions of estrogenic steroids for substitution. Estrone has been converted to 4β,5β-epoxy-10β-hydroxyestr-3-one; cleavage of this epoxyketone using an Eschenmoser procedure, and subsequent modification of the product afforded 4-seco-9-estren-3,5-dione 3-ethylene acetal. This versatile intermediate, suitable for substitution at the 9 and/or 10 position, was converted to androst-4-ene-3-one by known procedures.

Pulse NMR in solids : chemical shift, lead fluoride and thorium hydride

Part one of this thesis consists of two sections. In the first section the fluorine chemical shift of a single crystal CaF_2 has been measured as a function of external pressure up to 4 kilobar at room temperature using multiple pulse NMR techniques. The pressure dependence of the shift is found to be -1.7 ± 1 ppm/kbar, while a theoretical calculation using an overlap model predicts a shift of -0.46 ppm/kbar. In the second section a separation of the chemical shift tensor into physically meaningful "geometrical" and "chemical" contributions is presented and a comparison of the proposed model calculations with recently reported data on hydroxyl proton chemical shift tensors demonstrates, that for this system, the geometrical portion accounts for the qualitative features of the measured tensors.

Part two of the thesis consists of a study of fluoride ion motion in β-PbF_2 doped with NaF by measurement of the ^(19)F transverse relaxation time (T_2), spin lattice relaxation time (T_1) and the spin lattice relaxation time in the rotating frame (T_(1r)). Measurements over the temperature range of -50°C to 160°C lead to activation energies for T_1, T_(1r) and T_2 of 0.205 ± 0.01, 0.29 + 0.02 and 0.27 ± 0.01 ev/ion, and a T_(1r) minimum at 56°C yields a correlation time of 0.74 μsec. Pressure dependence of T_1 and T_2 yields activation volumes of <0.2 cm^3/g-mole and 1.76 ± 0.05 cm^3/g-mole respectively. These data along with the measured magnetic field independence of T_1 suggest that the measured T_1's are not caused by ^(19)F motion, but by thermally excited carriers.

Part three of the thesis consists of a study of two samples of Th_4H_(15), prepared under different conditions but both having the proper ratio of H/Th (to within 1%). The structure of the Th_4H_(15) as suggested by X-ray measurements is confirmed through a moment analysis of the rigid lattice line shape. T_1 and T_2 measurements above 390 K furnish activation energies of 16.3 ± 1.2 kcal/mole and 18.0 ± 3.0 kcal/mole, respectively. Below 350 K, T_(1r) measurements furnish an activation energy of 10.9 ± 0.7 kcal/mole, indicating most probably more than a single mechanism for proton motion. A time-temperature hysteresis effect of the proton motion was found in one of the two samples and is strongly indicative of a phase change. T_1 at room temperature and below is dominated by relaxation due to conduction electrons with the product T_1T being 180 ± 10 K-sec. Using multiple pulse techniques to greatly reduce homonuclear dipolar broadening, a temperature-dependent line shift was observed, and the chemical shift anisotropy is estimated to be less than 16 ppm.

Rate and Microstructure Effects on the Dynamics of Carbon Nanotube Foams

Soft hierarchical materials often present unique functional properties that are sensitive to the geometry and organization of their micro- and nano-structural features across different lengthscales. Carbon Nanotube (CNT) foams are hierarchical materials with fibrous morphology that are known for their remarkable physical, chemical and electrical properties. Their complex microstructure has led them to exhibit intriguing mechanical responses at different length-scales and in different loading regimes. Even though these materials have been studied for mechanical behavior over the past few years, their response at high-rate finite deformations and the influence of their microstructure on bulk mechanical behavior and energy dissipative characteristics remain elusive.

In this dissertation, we study the response of aligned CNT foams at the high strain-rate regime of 10² - 10⁴ s^-1. We investigate their bulk dynamic response and the fundamental deformation mechanisms at different lengthscales, and correlate them to the microstructural characteristics of the foams. We develop an experimental platform, with which to study the mechanics of CNT foams in high-rate deformations, that includes direct measurements of the strain and transmitted forces, and allows for a full field visualization of the sample’s deformation through high-speed microscopy.

We synthesize various CNT foams (e.g., vertically aligned CNT (VACNT) foams, helical CNT foams, micro-architectured VACNT foams and VACNT foams with microscale heterogeneities) and show that the bulk functional properties of these materials are highly tunable either by tailoring their microstructure during synthesis or by designing micro-architectures that exploit the principles of structural mechanics. We also develop numerical models to describe the bulk dynamic response using multiscale mass-spring models and identify the mechanical properties at length scales that are smaller than the sample height.

The ability to control the geometry of microstructural features, and their local interactions, allows the creation of novel hierarchical materials with desired functional properties. The fundamental understanding provided by this work on the key structure-function relations that govern the bulk response of CNT foams can be extended to other fibrous, soft and hierarchical materials. The findings can be used to design materials with tailored properties for different engineering applications, like vibration damping, impact mitigation and packaging.