Contribution to the Analysis, Design and Assessment of Compact Antenna Test Ranges At Millimeter Wavelengths - Contribución al Análisis, Diseño y Caracterización de Sistemas de Medida de Antenas en Rango Compacto para Frecuencias Milimétricas

This Doctoral Thesis entitled Contribution to the analysis, design and assessment of compact antenna test ranges at millimeter wavelengths aims to deepen the knowledge of a particular antenna measurement system: the compact range, operating in the frequency bands of millimeter wavelengths. The thesis has been developed at Radiation Group (GR), an antenna laboratory which belongs to the Signals, Systems and Radiocommunications department (SSR), from Technical University of Madrid (UPM). The Radiation Group owns an extensive experience on antenna measurements, running at present four facilities which operate in different configurations: Gregorian compact antenna test range, spherical near field, planar near field and semianechoic arch system. The research work performed in line with this thesis contributes the knowledge of the first measurement configuration at higher frequencies, beyond the microwaves region where Radiation Group features customer-level performance. To reach this high level purpose, a set of scientific tasks were sequentially carried out. Those are succinctly described in the subsequent paragraphs. A first step dealed with the State of Art review. The study of scientific literature dealed with the analysis of measurement practices in compact antenna test ranges in addition with the particularities of millimeter wavelength technologies. Joint study of both fields of knowledge converged, when this measurement facilities are of interest, in a series of technological challenges which become serious bottlenecks at different stages: analysis, design and assessment. Thirdly after the overview study, focus was set on Electromagnetic analysis algorithms. These formulations allow to approach certain electromagnetic features of interest, such as field distribution phase or stray signal analysis of particular structures when they interact with electromagnetic waves sources. Properly operated, a CATR facility features electromagnetic waves collimation optics which are large, in terms of wavelengths. Accordingly, the electromagnetic analysis tasks introduce an extense number of mathematic unknowns which grow with frequency, following different polynomic order laws depending on the used algorithmia. In particular, the optics configuration which was of our interest consisted on the reflection type serrated edge collimator. The analysis of these devices requires a flexible handling of almost arbitrary scattering geometries, becoming this flexibility the nucleus of the algorithmia’s ability to perform the subsequent design tasks. This thesis’ contribution to this field of knowledge consisted on reaching a formulation which was powerful at the same time when dealing with various analysis geometries and computationally speaking. Two algorithmia were developed. While based on the same principle of hybridization, they reached different order Physics performance at the cost of the computational efficiency. Inter-comparison of their CATR design capabilities was performed, reaching both qualitative as well as quantitative conclusions on their scope. In third place, interest was shifted from analysis - design tasks towards range assessment. Millimetre wavelengths imply strict mechanical tolerances and fine setup adjustment. In addition, the large number of unknowns issue already faced in the analysis stage appears as well in the on chamber field probing stage. Natural decrease of dynamic range available by semiconductor millimeter waves sources requires in addition larger integration times at each probing point. These peculiarities increase exponentially the difficulty of performing assessment processes in CATR facilities beyond microwaves. The bottleneck becomes so tight that it compromises the range characterization beyond a certain limit frequency which typically lies on the lowest segment of millimeter wavelength frequencies. However the value of range assessment moves, on the contrary, towards the highest segment. This thesis contributes this technological scenario developing quiet zone probing techniques which achieves substantial data reduction ratii. Collaterally, it increases the robustness of the results to noise, which is a virtual rise of the setup’s available dynamic range. In fourth place, the environmental sensitivity of millimeter wavelengths issue was approached. It is well known the drifts of electromagnetic experiments due to the dependance of the re sults with respect to the surrounding environment. This feature relegates many industrial practices of microwave frequencies to the experimental stage, at millimeter wavelengths. In particular, evolution of the atmosphere within acceptable conditioning bounds redounds in drift phenomena which completely mask the experimental results. The contribution of this thesis on this aspect consists on modeling electrically the indoor atmosphere existing in a CATR, as a function of environmental variables which affect the range’s performance. A simple model was developed, being able to handle high level phenomena, such as feed - probe phase drift as a function of low level magnitudes easy to be sampled: relative humidity and temperature. With this model, environmental compensation can be performed and chamber conditioning is automatically extended towards higher frequencies. Therefore, the purpose of this thesis is to go further into the knowledge of millimetre wavelengths involving compact antenna test ranges. This knowledge is dosified through the sequential stages of a CATR conception, form early low level electromagnetic analysis towards the assessment of an operative facility, stages for each one of which nowadays bottleneck phenomena exist and seriously compromise the antenna measurement practices at millimeter wavelengths.

Acute effects of endurance exercise on jumping and kicking performance in top-class young soccer players

The aim of this study was to examine the acute effects of endurance exercise on jumping and kicking performance in young soccer players. Twenty-one top-class young soccer players (16.1±0.2 years) performed a countermovement jump test and a maximal instep soccer kick test before and after running for 20 min on a treadmill at 80% of their individual maximum heart rate. Two force platforms were used to obtain the following parameters during the countermovement jump: jump height, maximum power, maximum power relative to body mass, maximum vertical ground reaction force, maximum vertical ground reaction force relative to body mass, and maximum vertical ground reaction force applied to each leg. Maximum vertical ground reaction force and maximum vertical ground reaction force relative to body mass applied to the support leg during the kicks were also calculated with a force platform. The kicking motion was recorded using a three-dimensional motion-capture system. Maximum velocity of the ball, maximum linear velocity of the toe, ankle, knee and hip, and linear velocity of the toe at ball contact during the kicks were calculated. Non-significant differences were found in the parameters measured during the countermovement jump and the maximal instep soccer kick test before and after running, suggesting that the jumping and kicking performances of top-class young soccer players were not significantly affected after 20 min treadmill running at 80% of their individual maximum heart rate.

Modelización de contactos termoelastohidrodinámicos

La mejora en la eficiencia energética y la reducción de la tasa de fallos en los contactos lubricados son aspectos que resultan de gran interés en numerosos sectores de la industria, y plantean en estos momentos nuevas dificultades operativas y retos para un futuro próximo. Los avances tecnológicos han incrementado las exigencias técnicas que se requieren a los aceites para cumplir su función al extender sus variables operativas a un mayor espectro de aplicaciones, tanto de condiciones de funcionamiento como a la gran variedad de nuevos materiales constitutivos de los engranajes en los que se tiene que utilizar. Por ello, actualmente se está incentivado el desarrollo de nuevos procedimientos que permitan comprender el comportamiento de este tipo de contactos lubricados, con el fin de lograr mejoras técnicas en su diseño y la correcta selección del aceite. En esta Tesis Doctoral se presenta una metodología de cálculo numérico que permite simular el comportamiento de contactos elastohidrodinámicos (EHD) puntuales, como puede ser el caso de un rodamiento. La resolución de este problema presenta diversas complejidades matemáticas y exige el desarrollo de un elaborado procedimiento de cálculo basado en técnicas multinivel. Para hacer del procedimiento una herramienta válida en un gran número de condiciones de funcionamiento y tipos de lubricantes, se ha tenido en cuenta en el cálculo la posible aparición de comportamientos no-Newtonianos del lubricante y fenómenos de generación y disipación de calor, provocados por el movimiento relativo del fluido y las superficies en contacto. Para la validación del procedimiento, se han contrastado los resultados numéricos obtenidos con nuestro método, con los resultados numéricos y experimentales publicados por otros autores y con valores experimentales propios medidos en un equipo de ensayo de contacto puntual tipo MTM. El desarrollo de este programa ha dotado a la División de Ingeniería de Máquinas de una herramienta que ha permitido, y sobre todo va permitir, evaluar la importancia de cada uno de los parámetros reológicos en los diferentes problemas que va a tener que abordar, evaluación que hasta el momento se realizaba con métodos aproximados que describen la fenomenología con mucha menos precisión. A la hora de emplear nuestro procedimiento numérico para simular situaciones reales, nos hemos encontrado con el obstáculo de que es muy complicado encontrar, en la bibliografía y bases de datos, los parámetros que caracterizan el comportamiento reológico del lubricante en las condiciones de presión, temperatura y grado de cizallamiento habituales en las que se trabaja en este tipo de contactos, y las pocas medidas que existen para estas condiciones de funcionamiento son poco fiables. Por ello como complemento al objetivo principal de esta Tesis hemos desarrollado una metodología para caracterizar los lubricantes en estas condiciones extremas. Dicha metodología está basada en la buena descripción que hace nuestro programa del coeficiente de fricción, lo que nos ha permitido obtener los parámetros reológicos del III lubricante a partir de las medidas experimentales del coeficiente de fricción generado en un equipo MTM lubricado con el lubricante que se desea caracterizar. Madrid, Octubre de 2012 IV Improving energy efficiency and reducing the failure rate in lubricated contacts are issues that are of great interest in many sectors of industry, and right now posed operational difficulties and new challenges for the near future. Technological advances have increased the technical demands required to oils to fulfil its role by extending its operational variables to a wider range of applications, both operating conditions and to the wide variety of new materials which constitute the gear in which must be used. For this reason, has being encouraged currently to develop new procedures to understand the behaviour of this type of lubricated contacts, in order to achieve improvements in design techniques and the correct oil selection. In this Thesis we present a numerical methodology to simulate the puntual elastohydrodynamic contact behaviour (EHD), such as a roller bearing. The resolution of this problem presents various mathematical complexities and requires the development of an elaborate calculation procedure based on multilevel techniques. To make the procedure a valid tool in a wide range of operating conditions and types of lubricants, has been taken into account in calculating the possible occurrence of non-Newtonian behaviour of the lubricant and phenomena of generation and dissipation of heat, caused by the fluid relative motion and contacting surfaces. For the validation of the method, we have compared the numerical results obtained with our method with numerical and experimental results published by other authors also with own experimental values measured on point-contact test equipment MTM. The development of this program has provided the Machines Engineering Division of a tool that has allowed, and especially will allow to evaluate the importance of each of the rheological parameters on the various problems that will have to be addressed, evaluation performed hitherto described methods that phenomenology approximated with much less accuracy. When using our numerical procedure to simulate real situations we have encountered the obstacle that is very difficult to find, in the literature and database, parameters characterizing the rheological behaviour of the lubricant in the usual conditions of pressure, temperature and shear rate in which you work in this type of contact, and the few measures that exist for these operating conditions are unreliable. Thus in addition to the main objective of this thesis, we have developed a methodology to characterize the lubricants in these extreme conditions. This methodology is based on the good description, which makes our program, of the coefficient of friction, that allowed us to obtain the lubricant rheological parameters from experimental measurements of the friction coefficient generated on lubricated MTM equipment with the lubricant to be characterized.

The scaled-time test as an alternative to the pseudo-dynamic test

The stepped and excessively slow execution of pseudo-dynamic tests has been found to be the source of some errors arising from strain-rate effect and stress relaxation. In order to control those errors, a new continuous test method which allows the selection of a more suitable time scale factor in the response is proposed in this work. By dimensional analysis, such scaled-time response is obtained theoretically by augmenting the inertial and damping properties of the structure, for which we propose the use of hydraulic pistons which are servo-controlled to produce active mass and damping, nevertheless using an equipment which is similar to that required in a pseudo-dynamic test. The results of the successful implementation of this technique for a simple specimen are shown here.

Sudden transition to chaos in plasma wave interactions

The coherent three-wave interaction, with linear growth in the higher frequency wave and damping in the two other waves, is reconsidered; for equal dampings, the resulting three-dimensional (3-D) flow of a relative phase and just two amplitudes behaved chaotically, no matter how small the growth of the unstable wave. The general case of different dampings is studied here to test whether, and how, that hard scenario for chaos is preserved in passing from 3-D to four-dimensional flows. It is found that the wave with higher damping is partially slaved to the other damped wave; this retains a feature of the original problem an invariant surface that meets an unstable fixed point, at zero growth rate! that gave rise to the chaotic attractor and determined its structure, and suggests that the sudden transition to chaos should appear in more complex wave interactions.

Compatibilidad de Orius laevigatus (Fieber) (Hemiptera: Anthocoridae) y Nesidiocoris tenuis (Reuter)(Hemiptera: Miridae), depredadores importantes en cultivos hortícolas protegidos, con nuevas barreras físicas selectivas y modernos plaguicidas

La nueva legislación en materia fitosanitaria se dirige hacia una Gestión Integrada de Plagas (GIP). Estos programas dan preferencia a aquellos métodos más respetuosos y sostenibles con el medio ambiente, siendo piezas claves en ellos el control biológico, el físico y otros de carácter no químico. Sin embargo, el uso de insecticidas selectivos es a veces necesario para el adecuado manejo de plagas en cultivos hortícolas. Por ello, el objetivo general de este estudio es aportar conocimientos para mejorar el control de plagas en cultivos hortícolas, mediante la integración de tres estrategias de lucha: biológica, física y química. Una parte de este trabajo ha consistido en el estudio de los posibles efectos que mallas tratadas con insecticida (bifentrin) pudieran provocar mediante diferentes ensayos de laboratorio, invernadero y campo, en los enemigos naturales Orius laevigatus (Fieber) (Hemiptera: Anthocoridae) (depredador de trips), Nesidiocoris tenuis (Reuter) (Hemiptera: Miridae) (depredador de mosca blanca y Tuta absoluta (Meirick) (Lepidoptera: Gelechiidae)), y otros agentes de biocontrol comúnmente usados en cultivos hortícolas protegidos. Este tipo de mallas se han empleado con éxito en entomología médica para controlar mosquitos vectores de la malaria, y actualmente se está trabajando en su desarrollo para uso agrícola como método de exclusión, y método directo de control de plagas. En los ensayos realizados en laboratorio, O. laevigatus y N. tenuis no fueron capaces de detectar la presencia de bifentrin en el ensayo de preferencia. Además, no se produjo mortalidad a corto plazo (72 horas) en ambos chinches depredadores. Por el contrario, se registró una elevada mortalidad cuando se expusieron por contacto a la malla tratada durante 72 horas en cajas de dimensiones reducidas (10 cm de diámetro X 3 cm de altura). En ensayos llevados a cabo bajo condiciones más reales de exposición, en un invernadero experimental con jaulas de 25 X 25 X 60 cm de altura, no se produjo ningún efecto en la mortalidad a corto plazo (72 horas) o en los parámetros reproductivos de O. laevigatus y N. tenuis. Finalmente, en ensayos de campo realizados en túneles semi-comerciales (8 m de largo X 6,5 m de ancho X 2,6 m de altura), ni las condiciones ambientales [temperatura, humedad relativa, radiación ultravioleta (UV) y fotosintéticamente activa (PAR)], ni los enemigos naturales, se vieron afectados por la presencia de la malla tratada con bifentrin en el cultivo. Sin embargo, los resultados no fueron concluyentes, debido al bajo establecimiento de los agentes de biocontrol liberados. Por lo tanto, más estudios son necesarios en invernaderos comerciales para confirmar los resultados preliminares de compatibilidad. Además, en este trabajo se han evaluado los efectos letales (mortalidad) y subletales (parámetros reproductivos) de seis modernos insecticidas sobre los chinches depredadores O. laevigatus y N. tenuis, mediante ensayos de laboratorio y persistencia. Los ensayos se realizaron por contacto residual, aplicando los insecticidas a la dosis máxima de campo sobre placas de cristal (laboratorio) o plantas (persistencia). Los productos fitosanitarios se seleccionaron por representar a un grupo de modernos plaguicidas con modos de acción en principio más selectivos para los enemigos naturales que antiguos plaguicidas como organoclorados, oroganofosforados o carbamatos, y por su uso frecuente en cultivos hortícolas donde O. laevigatus y N. tenuis están presentes. Todos ellos están incluidos o en proceso de inclusión en la lista comunitaria de sustancias activas para uso agrícola, Anexo I de la Directiva 91/414/CEE: abamectina y emamectina (avermectinas neurotóxicas, activadoras del canal del cloro), deltametrina (piretroide neurotóxico, modulador del canal del sodio, control positivo), flubendiamida (neurotóxico, modulador del receptor de rianodina), spinosad (naturalito neurotóxico, agonistas/antagonistas del receptor de nicotínico acetilcolina) y spiromesifen (inhibidor de la acetil CoA carboxilasa). El estudio mostró que O. laevigatus fue más susceptible a los insecticidas que N. tenuis. Además, los resultados revelaron que flubendiamida y spiromesifen fueron compatibles con los dos enemigos naturales estudiados, y por tanto se podrían usar en programas de GIP. Por el contrario, los insecticidas abamectina, deltametrina, emamectina y spinosad no fueron selectivos para ninguno de los chinches depredadores. Sin embargo, los estudios de persistencia demostraron que a pesar de que estos insecticidas no proporcionaron selectividad fisiológica, pueden proporcionar selectividad ecológica en algunos casos. Abamectina, deltametrina, emamectina y spinosad podrían ser compatibles con N. tenuis si el enemigo natural es introducido en el cultivo 4 días después de su aplicación. En el caso de O. laevigatus, abamectina, deltametrina y spinosad se clasificaron como persistentes, por lo tanto es necesario completar el estudio con experimentos de semi-campo y campo que determinen si es posible su uso conjunto en programas de GIP. Por otro lado, emamectina podría ser compatible con O. laevigatus si el enemigo natural es introducido en el cultivo 7 días después de su aplicación. Por último, se ha comprobado la selectividad de tres insecticidas aceleradores de la muda (MACs) (metoxifenocida, tebufenocida y RH-5849) sobre O. laevigatus y N. tenuis. Además de realizar estudios para evaluar la toxicidad en laboratorio de los insecticidas por contacto residual e ingestión (principal modo de acción de los MAC´s), se extrajo RNA de los insectos y con el cDNA obtenido se secuenció y clonó el dominio de unión al ligando (LBD) del receptor de ecdisona correspondiente a O. laevigatus (OlEcR-LBD) y N. tenuis (NtEcR-LBD). Posteriormente, se obtuvo la configuración en tres dimensiones del LBD y se estudió el acoplamiento de las moléculas de los tres insecticidas en la cavidad que forman las 12 α-hélices que constituyen el EcR-LBD. En el caso de N. tenuis se debe mencionar que no fue posible la obtención de la secuencia completa del LBD. Sin embargo, se obtuvo una secuencia parcial (hélice 6-hélice 11), que mostró una alta conservación de aminoácidos con respecto a la obtenida en O. laevigatus. Los ensayos de toxicidad mostraron que metoxifenocida, tebufenocida y RH-5849 no produjeron ningún efecto nocivo en ambos depredadores. Además, los estudios de modelado por homología y acoplamiento molecular llevados a cabo con O. laevigatus, también indicaron que los MACs no produjeron ningún efecto deletéreo en este enemigo natural. Por lo tanto, estos compuestos pueden ser aplicados de manera segura en programas de GIP en los cuales O. laevigatus y N. tenuis estén presentes. ABSTRACT The new pesticide legislation on pest control is aimed at integrated pest management (IPM). These programs are based on the most environmentally sustainable approaches, where biological, physical control and other non-chemical methods are the cornerstone. However, selective pesticides are often required for pest management on horticultural crops. Therefore, the main goal of this study is to provide knowledge to improve pest control on horticultural crops through the integration of three strategies: biological, physical and chemical. Firstly, the effects of insecticide treated nets (bifenthrin) were evaluated in different laboratory, greenhouse and field experiments on the natural enemies Orius laevigatus (Fieber) (Hemiptera: Anthocoridae) (predator of thrips), Nesidiocoris tenuis (Reuter) (Hemiptera: Miridae) (predator of whiteflies and Tuta absoluta (Meirick) (Lepidoptera: Gelechiidae)), and other biocontrol agents commonly used on protected horticultural crops. These types of nets have been successfully used in medical entomology to control mosquito malaria vectors, and work is currently being done on their use as exclusion barriers and as a direct method of pest control in agriculture. In experiments made under laboratory conditions, O. laevigatus and N. tenuis were not able to detect the presence of bifenthrin in a dual-choice test. Furthermore, no shortterm mortality (72 hours) was recorded on both predatory bugs. In contrast, a high mortality rate was found when they were exposed by contact to the bifenthrin-treated net for 72 hours in small cages (10 cm diameter X 3 cm high). In assays carried out under more realistic conditions of exposure, in an experimental greenhouse with cages of 25 X 25 X 60 cm high, short-term mortality (72 hours) and reproductive parameters were not affected. Lastly, in field experiments carried out in semi-commercial tunnels (8 m long X 6.5 m width X 2.6 m high), neither environmental conditions [temperature, relative humidity, ultraviolet (UV) and photosynthetically active radiation (PAR)] nor natural enemies were affected by the presence of the bifenthrin-treated net on the crop. However, results were not conclusive, mainly due to a low settlement of the released biocontrol agents, and further studies are needed in commercial greenhouses to confirm our preliminary results of compatibility. Secondly, the lethal (mortality) and sublethal effects (reproductive parameters) of six modern pesticides on the predatory bugs O. laevigatus and N. tenuis has been evaluated through laboratory and persistence experiments. Trials were carried out by residual contact, applying the insecticides to the maximum field recommended concentration on glass plates (laboratory) or plants (persistence). Insecticides were chosen as representatives of modern pesticides with a more selective mode of action on natural enemies than organochlorine, organophosphorus and carbamate insecticides. Moreover, they were also chosen because of their frequent use on horticultural crops where O. laevigatus and N. tenuis are present. All of them have been included or have been requested for inclusion in the community list of active substances on the agricultural market, Annex I of the European Directive 91/414/EEC: abamectin and emamectin (neurotoxic avermectins, chloride channel activators), deltamethrin (neutotoxic pyrethroid, sodium channel modulator, positive commercial standard), flubendiamide (neurotoxic, rianodine receptor modulator), spinosad (neurotoxic naturalyte, nicotinic acetylcholine receptor allosteric activator) and spiromesifen (inhibitors of acetyl CoA carboxylase). The study showed that O. laevigatus was more susceptible to all the studied pesticides than N. tenuis. In addition, the research results indicated no impact of flubendiamide and spiromesifen on the two natural enemies studied under laboratory conditions. Consequently, both pesticides are candidates to be included in IPM programmes where these biocontrol agents are present. On the other hand, abamectin, deltamethrin, emamectin and spinosad were not selective for both predatory bugs in laboratory experiments. However, persistence test demonstrated that in spite of the lack of physiological selectivity, these pesticides can provide ecological selectivity in some cases. Abamectin, deltamethrin, emamectin and spinosad could be compatible with N. tenuis if the mirid bug is released 4 days after the insecticide treatment on the crop. With regard to O. laevigatus, abamectin, deltamethrin and spinosad were classified as persistent in our assays, thus the study should be completed with semi-field and field experiments in order to ascertain their possible joint use in IPM programs. In contrast, emamectin could be compatible with O. laevigatus if the pirate bug is released 7 days after the insecticide treatment on the crop. Finally, the selectivity of three moulting accelerating compounds (MACs) (methoxyfenozide, tebufenozide and RH-5849) has also been evaluated on O. laevigatus and N. tenuis. In addition to laboratory experiments to evaluate the toxicity of the insecticides by residual contact and ingestion, molecular approaches were used as well. RNA of both insects was isolated, cDNA was subsequently synthesized and the complete sequence of the ligand binding domain (LBD) of the ecdysone receptor of O. laevigatus (OlEcR-LBD) and N. tenuis (NtEcR-LBD) were determined. Afterwards, the three dimensional structure of LBD was constructed. Finally, the docking of the insecticide molecules in the cavity delineated by the 12 α-helix that composed the EcRLBD was performed. In the case of N. tenuis, it should be noted that in spite of intensive efforts, we did not manage to complete the sequence for the LBD.However, a partial sequence of the LBD was obtained (helix 6-helix 11), and a strong conservation between the amino acids of N. tenuis and O. laevigatus was observed. Results showed no biological activity of methoxyfenozide, tebufenozide and RH-5849, on both predatory bugs. Moreover, modeling of the OlEcR-LBD and docking experiments also suggested that MACs were devoid of any deleterious effect on O. laevigatus. Therefore, our results indicate that these compounds could be safely applied in IPM programs in which O. laevigatus and N. tenuis are present.

Determination of the JWL constants for ANFO and emulsion explosives from cylinder test data

The Jones-Wilkins-Lee (JWL) equation of state parameters for ANFO and emulsion-type explosives have been obtained from cylinder test expansion measurements. The calculation method comprises a new radial expansion function, with a non-zero initial velocity at the onset of the expansion in order to comply with a positive Gurney energy at unit relative volume, as the isentropic expansion from the CJ state predicts. The equations reflecting the CJ state conditions and the measured expansion energy were solved for the JWL parameters by a non-linear least squares scheme. The JWL parameters of thirteen ANFO and emulsion type explosives have been determined in this way from their cylinder test expansion data. The results were evaluated through numerical modelling of the tests with the LS-DYNA hydrocode; the expansion histories from the modelling were compared with the measured ones, and excellent agreement was found.

Entrainment Effects in Turbulent Boundary Layers

Esta tesis estudia el comportamiento de la región exterior de una capa límite turbulenta sin gradientes de presiones. Se ponen a prueba dos teorías relativamente bien establecidas. La teoría de semejanza para la pared supone que en el caso de haber una pared rugosa, el fluido sólo percibe el cambio en la fricción superficial que causa, y otros efectos secundarios quedarán confinados a una zona pegada a la pared. El consenso actual es que dicha teoría es aproximadamente cierta. En el extremo exterior de la capa límite existe una región producida por la interacción entre las estructuras turbulentas y el flujo irrotacional de la corriente libre llamada interfaz turbulenta/no turbulenta. La mayoría de los resultados al respecto sugieren la presencia de fuerzas de cortadura ligeramente más intensa, lo que la hace distinta al resto del flujo turbulento. Las propiedades de esa región probablemente cambien si la velocidad de crecimiento de la capa límite aumenta, algo que puede conseguirse aumentando la fricción en la pared. La rugosidad y la ingestión de masa están entonces relacionadas, y el comportamiento local de la interfaz turbulenta/no turbulenta puede explicar el motivo por el que las capas límite sobre paredes rugosas no se comportan como en el caso de tener paredes lisas precisamente en la zona exterior. Para estudiar las capas límite a números de Reynolds lo suficientemente elevados, se ha desarrollado un nuevo código de alta resolución para la simulación numérica directa de capas límite turbulentas sin gradiente de presión. Dicho código es capaz de simular capas límite en un intervalo de números de Reynolds entre ReT = 100 — 2000 manteniendo una buena escalabilidad hasta los dos millones de hilos en superordenadores de tipo Blue Gene/Q. Se ha guardado especial atención a la generación de condiciones de contorno a la entrada correctas. Los resultados obtenidos están en concordancia con los resultados previos, tanto en el caso de simulaciones como de experimentos. La interfaz turbulenta/no turbulenta de una capa límite se ha analizado usando un valor umbral del módulo de la vorticidad. Dicho umbral se considera un parámetro para analizar cada superficie obtenida de un contorno del módulo de la vorticidad. Se han encontrado dos regímenes distintos en función del umbral escogido con propiedades opuestas, separados por una transición topológica gradual. Las características geométricas de la zona escalan con o99 cuando u^/isdgg es la unidad de vorticidad. Las propiedades del íluido relativas a la posición del contorno de vorticidad han sido analizados para una serie de umbrales utilizando el campo de distancias esféricas, que puede obtenerse con independencia de la complejidad de la superficie de referencia. Las propiedades del fluido a una distancia dada del inerfaz también dependen del umbral de vorticidad, pero tienen características parecidas con independencia del número de Reynolds. La interacción entre la turbulencia y el flujo no turbulento se restringe a una zona muy fina con un espesor del orden de la escala de Kolmogorov local. Hacia el interior del flujo turbulento las propiedades son indistinguibles del resto de la capa límite. Se ha simulado una capa límite sin gradiente de presiones con una fuerza volumétrica cerca de la pared. La el forzado ha sido diseñado para aumentar la fricción en la pared sin introducir ningún efecto geométrico obvio. La simulación consta de dos dominios, un primer dominio más pequeño y a baja resolución que se encarga de generar condiciones de contorno correctas, y un segundo dominio mayor y a alta resolución donde se aplica el forzado. El estudio de los perfiles y los coeficientes de autocorrelación sugieren que los dos casos, el liso y el forzado, no colapsan más allá de la capa logarítmica por la complejidad geométrica de la zona intermitente, y por el hecho que la distancia a la pared no es una longitud característica. Los efectos causados por la geometría de la zona intermitente pueden evitarse utilizando el interfaz como referencia, y la distancia esférica para el análisis de sus propiedades. Las propiedades condicionadas del flujo escalan con 5QQ y u/uT, las dos únicas escalas contenidas en el modelo de semejanza de pared de Townsend, consistente con estos resultados. ABSTRACT This thesis studies the characteristics of the outer region of zero-pressure-gradient turbulent boundary layers at moderate Reynolds numbers. Two relatively established theories are put to test. The wall similarity theory states that with the presence of roughness, turbulent motion is mostly affected by the additional drag caused by the roughness, and that other secondary effects are restricted to a region very close to the wall. The consensus is that this theory is valid, but only as a first approximation. At the edge of the boundary layer there is a thin layer caused by the interaction between the turbulent eddies and the irroational fluid of the free stream, called turbulent/non-turbulent interface. The bulk of results about this layer suggest the presence of some localized shear, with properties that make it distinguishable from the rest of the turbulent flow. The properties of the interface are likely to change if the rate of spread of the turbulent boundary layer is amplified, an effect that is usually achieved by increasing the drag. Roughness and entrainment are therefore linked, and the local features of the turbulent/non-turbulent interface may explain the reason why rough-wall boundary layers deviate from the wall similarity theory precisely far from the wall. To study boundary layers at a higher Reynolds number, a new high-resolution code for the direct numerical simulation of a zero pressure gradient turbulent boundary layers over a flat plate has been developed. This code is able to simulate a wide range of Reynolds numbers from ReT =100 to 2000 while showing a linear weak scaling up to around two million threads in the BG/Q architecture. Special attention has been paid to the generation of proper inflow boundary conditions. The results are in good agreement with existing numerical and experimental data sets. The turbulent/non-turbulent interface of a boundary layer is analyzed by thresholding the vorticity magnitude field. The value of the threshold is considered a parameter in the analysis of the surfaces obtained from isocontours of the vorticity magnitude. Two different regimes for the surface can be distinguished depending on the threshold, with a gradual topological transition across which its geometrical properties change significantly. The width of the transition scales well with oQg when u^/udgg is used as a unit of vorticity. The properties of the flow relative to the position of the vorticity magnitude isocontour are analyzed within the same range of thresholds, using the ball distance field, which can be obtained regardless of the size of the domain and complexity of the interface. The properties of the flow at a given distance to the interface also depend on the threshold, but they are similar regardless of the Reynolds number. The interaction between the turbulent and the non-turbulent flow occurs in a thin layer with a thickness that scales with the Kolmogorov length. Deeper into the turbulent side, the properties are undistinguishable from the rest of the turbulent flow. A zero-pressure-gradient turbulent boundary layer with a volumetric near-wall forcing has been simulated. The forcing has been designed to increase the wall friction without introducing any obvious geometrical effect. The actual simulation is split in two domains, a smaller one in charge of the generation of correct inflow boundary conditions, and a second and larger one where the forcing is applied. The study of the one-point and twopoint statistics suggest that the forced and the smooth cases do not collapse beyond the logarithmic layer may be caused by the geometrical complexity of the intermittent region, and by the fact that the scaling with the wall-normal coordinate is no longer present. The geometrical effects can be avoided using the turbulent/non-turbulent interface as a reference frame, and the minimum distance respect to it. The conditional analysis of the vorticity field with the alternative reference frame recovers the scaling with 5QQ and v¡uT already present in the logarithmic layer, the only two length-scales allowed if Townsend’s wall similarity hypothesis is valid.

Crecimiento forestal en el bosque tropical de montaña: efectos de la diversidad florística y de la manipulación de nutrientes

El bosque tropical de montaña, es considerado zona de mega diversidad y de alto grado de endemismo, por las diferentes zonas ecológicas que presenta. Durante las últimas décadas estos bosques han recibido mayor atención por parte de investigadores, sin embargo, aún existe poca investigación en determinar cuáles son las respuestas de los bosques a los cambios ambientales a los que son sometidos. Estos bosques están sufriendo serias amenazas como pérdida de cobertura vegetal y cambios en los ciclos de nutrientes. El trabajo se dividió en cuatro objetivos específicos. i) Caracterización y análisis de patrones altitudinales de la riqueza de especies en el bosque tropical de montaña en el sur del Ecuador; con el fin de conocer cómo varía la diversidad de especies riqueza lo largo de un gradiente altitudinal. ii) Conocer los patrones espaciales del crecimiento en tres remanentes boscosos de un bosque tropical de montaña para determinar cómo la vecindad y la semejanza funcional de ésta influyen en el crecimiento forestal. iii) Conocer los efectos de la fertilización en el crecimiento diamétrico de especies arbóreas, en el bosque tropical de montaña; se analizó cómo reaccionan los árboles a la adición de nutrientes N y P en tres tipos de bosque. iv) Saber la respuesta de la comunidad de árboles a la adición de nutrientes en el bosque montano andino; este objetivo se basó con el supuesto de la deficiencia de tres tipos de nutrientes N, P y Ca, en esta formación boscosa y cómo reaccionan los árboles a la adición de nutrientes. El presente trabajo se llevó a cabo, en el bosque tropical de montaña que se encuentra localizada en la parte adyacente del Parque Nacional Podocarpus (PNP) en la cordillera del Consuelo, forma parte de la cadena oriental de los Andes del sur del Ecuador El trabajo de desarrollo entre los años 2008 y 2014. Para abordar el primer objetivo se establecieron 54 parcelas ubicadas aleatoriamente a lo largo de un gradiente altitudinal (3 niveles de altitud) y se e midieron e identificaron todos los individuos mayores a 5cm de DAP. Se construyó una filogenia con Phylocom y se calcularon diferentes componentes de diversidad para cada parcela ( riqueza taxonómica, diversidad filogenética y edad media de las especies). Ajustando modelos lineares se contrastó el efecto de la altitud sobre dichos componentes y se vio que la riqueza taxonómica y la edad media de las especies aumentaron con la altitud, en sentido contrario a las predicciones de la "hipótesis del conservadurismo tropical" (Tropical Conservatism Hypothesis). Para abordar el segundo objetivo se realizó una remedición de todos los árboles cartografiados en tres parcelas permanentes de alrededor de 5000 m2 cada una, representativas de tres estados diferentes de la sucesión del bosque montano. A partir de las coordenadas y de los datos de registrados, y empleando diferentes funciones de correlación de marca se analizó la distribución espacial del tamaño y del crecimiento relativo y del tamaño. Se constató que mientras que el tamaño de los árboles presentó una correlación espacial negativa, el crecimiento presentó correlación espacial positiva, en ambos casos a distancias cortas. El rango y la magnitud de ambas correlaciones aumentaron al avanzar la sucesión. La distribución espacial del crecimiento mostró una correlación negativa con la distribución espacial de tamaños. Por otro lado, la distribución espacial del crecimiento mostró una correlación negativa para árboles semejantes funcionalmente y positiva cuando se calculó entre árboles con diferente estrategia funcional. En conjunto, los resultados obtenidos señalan un aumento de la importancia de procesos competitivos y una mayor estructuración espacial del crecimiento y de la distribución de tamaños al avanzar la sucesión. Para el tercer y cuarto objetivo se instalaron 52 parcelas distribuidas en bloques donde se fertilizaron dos veces al año durante 6,4 años, se identificaron todos los individuos mayores a 10 cm de DAP, y se midió el crecimiento diamétrico durante estos años Con la adición de nutrientes realizada a los diferentes tipos de bosque en la gradiente altitudinal, encontramos que el efecto sobre el crecimiento diamétrico en la comunidad varia con el rango altitudinal, y el tipo de nutriente, analizando a nivel de las especies, en la mayoría de los casos las especies comunes no tuvieron cambios significativos a la adición de nutrientes. Los resultados de este estudio aportan nuevas evidencias para el entendimiento de la diversidad, estructura y dinámica de los bosques tropicales de montaña. ABSTRACT The montane tropical forest is considered a megadiverse habitat that harbor an enormous degree of endemism. This is mainly due to the high degree of environmental heterogeneity found and the presence of different well defined ecological areas. These forests have received more attention during the last decades, however, the information regarding the responses of these forests to environmental change, is still scarce. These forests are seriously endangered and are suffering serious threats, such as loss of vegetative cover, changes in the nutrient cycles. The work was divided in four specific objectives: i) Characterization and analysis of the species richness altitudinal patterns in the montane tropical forest of south Ecuador. Specifically, how species diversity changes along altitudinal gradients. ii) Exploring the spatial patterns of tree growth in three remnants of a montane tropical forest, and analyze how tree neighborhood and functional similarity among trees influence tree growth. Tropical Conservatism Hypothesis iii) Understanding the effects of fertilization in arboreal species growth (increase in diameter) of the montane tropical forest. Specifically we studied the effects of P and N addition on three different forests across an altitudinal gradient. iv) Know the response of the community of trees to the addition of nutrients in the Andean montane forest; this objective was based on the supposition of deficiency of three types of nutrients: P, N and Ca in this forest all formation and how the trees react to the addition of these nutrients. The present work was carried out in the montane tropical forest located in Bombuscaro, San Francisco and Cajanuma close to Podocarpus National Park (PNP) on Consuelo mountain range (Andean oriental range) at South of Ecuador. Field work was carried out during 2008 and 2014. To address the first objective, we randomly placed 54 plots along an altitudinal gradient. In these plots, every individual larger than 5 cm of DBH was measured and identified. A phylogeny was build with Phylocom and different diversity components (taxonomic richness, phylogenetic diversity and average species age) were computed for each plot. Linear models were used to test the effects of altitude on the diversity components. Our results showed that, contrary to the Tropical Conservatism Hypothesis, both taxonomic richness and average species age increased with altitude. To address our second objective, all mapped trees in three successional permanent plots (around ~5000 m2 each) were re-measured. Using different mark correlation functions, we analyzed the spatial distribution of tree-size and tree relative growth rate. Whereas tree size showed negative spatial correlation at fine spatial scales, relative growth rate showed positive correlation at the same scales. The range and magnitude of those correlations increased along successional stage. The spatial distribution of the relative growth rate was negatively correlated with the spatial distribution of tree sizes. Additionally, we found that the spatial correlation of the relative growth rate was negative for functionally similar trees and positive when computed for functionally different trees. In synthesis, our results point to an increase of competitive processes and strong spatial structure of relative growth rate and tree size along succession. For the third and fourth objectives, 52 plots were placed in a block design and were fertilized twice a year for 6,4 years. In these plots all the individuals with DBH > 10 cm were identified, and the diametrical growth was measured during these years. The nutrient addition at the three different altitude forests, revealed that the effect on the diametrical growth in the community varied with the altitudinal range. When analyzed at species level, the addition of nutrients was no significant in most cases. These results represent new evidences that will improved our understanding of diversity patterns and structure, and the dynamics of tropical montane forests.

Methodology for instantaneous average exhaust gas mass flow rate measurement

This paper presents a new methodology for measurement of the instantaneous average exhaust mass flow rate in reciprocating internal combustion engines to be used to determinate real driving emissions on light duty vehicles, as part of a Portable Emission Measurement System (PEMS). Firstly a flow meter, named MIVECO flow meter, was designed based on a Pitot tube adapted to exhaust gases which are characterized by moisture and particle content, rapid changes in flow rate and chemical composition, pulsating and reverse flow at very low engine speed. Then, an off-line methodology was developed to calculate the instantaneous average flow, considering the ?square root error? phenomenon. The paper includes the theoretical fundamentals, the developed flow meter specifications, the calibration tests, the description of the proposed off-line methodology and the results of the validation test carried out in a chassis dynamometer, where the validity of the mass flow meter and the methodology developed are demonstrated.