Dynamic analysis of payloads and structures with intermediate modal density

La necesidad de desarrollar técnicas para predecir la respuesta vibroacústica de estructuras espaciales lia ido ganando importancia en los últimos años. Las técnicas numéricas existentes en la actualidad son capaces de predecir de forma fiable el comportamiento vibroacústico de sistemas con altas o bajas densidades modales. Sin embargo, ambos rangos no siempre solapan lo que hace que sea necesario el desarrollo de métodos específicos para este rango, conocido como densidad modal media. Es en este rango, conocido también como media frecuencia, donde se centra la presente Tesis doctoral, debido a la carencia de métodos específicos para el cálculo de la respuesta vibroacústica. Para las estructuras estudiadas en este trabajo, los mencionados rangos de baja y alta densidad modal se corresponden, en general, con los rangos de baja y alta frecuencia, respectivamente. Los métodos numéricos que permiten obtener la respuesta vibroacústica para estos rangos de frecuencia están bien especificados. Para el rango de baja frecuencia se emplean técnicas deterministas, como el método de los Elementos Finitos, mientras que, para el rango de alta frecuencia las técnicas estadísticas son más utilizadas, como el Análisis Estadístico de la Energía. En el rango de medias frecuencias ninguno de estos métodos numéricos puede ser usado con suficiente precisión y, como consecuencia -a falta de propuestas más específicas- se han desarrollado métodos híbridos que combinan el uso de métodos de baja y alta frecuencia, intentando que cada uno supla las deficiencias del otro en este rango medio. Este trabajo propone dos soluciones diferentes para resolver el problema de la media frecuencia. El primero de ellos, denominado SHFL (del inglés Subsystem based High Frequency Limit procedure), propone un procedimiento multihíbrido en el cuál cada subestructura del sistema completo se modela empleando una técnica numérica diferente, dependiendo del rango de frecuencias de estudio. Con este propósito se introduce el concepto de límite de alta frecuencia de una subestructura, que marca el límite a partir del cual dicha subestructura tiene una densidad modal lo suficientemente alta como para ser modelada utilizando Análisis Estadístico de la Energía. Si la frecuencia de análisis es menor que el límite de alta frecuencia de la subestructura, ésta se modela utilizando Elementos Finitos. Mediante este método, el rango de media frecuencia se puede definir de una forma precisa, estando comprendido entre el menor y el mayor de los límites de alta frecuencia de las subestructuras que componen el sistema completo. Los resultados obtenidos mediante la aplicación de este método evidencian una mejora en la continuidad de la respuesta vibroacústica, mostrando una transición suave entre los rangos de baja y alta frecuencia. El segundo método propuesto se denomina HS-CMS (del inglés Hybrid Substructuring method based on Component Mode Synthesis). Este método se basa en la clasificación de la base modal de las subestructuras en conjuntos de modos globales (que afectan a todo o a varias partes del sistema) o locales (que afectan a una única subestructura), utilizando un método de Síntesis Modal de Componentes. De este modo es posible situar espacialmente los modos del sistema completo y estudiar el comportamiento del mismo desde el punto de vista de las subestructuras. De nuevo se emplea el concepto de límite de alta frecuencia de una subestructura para realizar la clasificación global/local de los modos en la misma. Mediante dicha clasificación se derivan las ecuaciones globales del movimiento, gobernadas por los modos globales, y en las que la influencia del conjunto de modos locales se introduce mediante modificaciones en las mismas (en su matriz dinámica de rigidez y en el vector de fuerzas). Las ecuaciones locales se resuelven empleando Análisis Estadístico de Energías. Sin embargo, este último será un modelo híbrido, en el cual se introduce la potencia adicional aportada por la presencia de los modos globales. El método ha sido probado para el cálculo de la respuesta de estructuras sometidas tanto a cargas estructurales como acústicas. Ambos métodos han sido probados inicialmente en estructuras sencillas para establecer las bases e hipótesis de aplicación. Posteriormente, se han aplicado a estructuras espaciales, como satélites y reflectores de antenas, mostrando buenos resultados, como se concluye de la comparación de las simulaciones y los datos experimentales medidos en ensayos, tanto estructurales como acústicos. Este trabajo abre un amplio campo de investigación a partir del cual es posible obtener metodologías precisas y eficientes para reproducir el comportamiento vibroacústico de sistemas en el rango de la media frecuencia. ABSTRACT Over the last years an increasing need of novel prediction techniques for vibroacoustic analysis of space structures has arisen. Current numerical techniques arc able to predict with enough accuracy the vibro-acoustic behaviour of systems with low and high modal densities. However, space structures are, in general, very complex and they present a range of frequencies in which a mixed behaviour exist. In such cases, the full system is composed of some sub-structures which has low modal density, while others present high modal density. This frequency range is known as the mid-frequency range and to develop methods for accurately describe the vibro-acoustic response in this frequency range is the scope of this dissertation. For the structures under study, the aforementioned low and high modal densities correspond with the low and high frequency ranges, respectively. For the low frequency range, deterministic techniques as the Finite Element Method (FEM) are used while, for the high frequency range statistical techniques, as the Statistical Energy Analysis (SEA), arc considered as more appropriate. In the mid-frequency range, where a mixed vibro-acoustic behaviour is expected, any of these numerical method can not be used with enough confidence level. As a consequence, it is usual to obtain an undetermined gap between low and high frequencies in the vibro-acoustic response function. This dissertation proposes two different solutions to the mid-frequency range problem. The first one, named as The Subsystem based High Frequency Limit (SHFL) procedure, proposes a multi-hybrid procedure in which each sub-structure of the full system is modelled with the appropriate modelling technique, depending on the frequency of study. With this purpose, the concept of high frequency limit of a sub-structure is introduced, marking out the limit above which a substructure has enough modal density to be modelled by SEA. For a certain analysis frequency, if it is lower than the high frequency limit of the sub-structure, the sub-structure is modelled through FEM and, if the frequency of analysis is higher than the high frequency limit, the sub-structure is modelled by SEA. The procedure leads to a number of hybrid models required to cover the medium frequency range, which is defined as the frequency range between the lowest substructure high frequency limit and the highest one. Using this procedure, the mid-frequency range can be define specifically so that, as a consequence, an improvement in the continuity of the vibro-acoustic response function is achieved, closing the undetermined gap between the low and high frequency ranges. The second proposed mid-frequency solution is the Hybrid Sub-structuring method based on Component Mode Synthesis (HS-CMS). The method adopts a partition scheme based on classifying the system modal basis into global and local sets of modes. This classification is performed by using a Component Mode Synthesis, in particular a Craig-Bampton transformation, in order to express the system modal base into the modal bases associated with each sub-structure. Then, each sub-structure modal base is classified into global and local set, fist ones associated with the long wavelength motion and second ones with the short wavelength motion. The high frequency limit of each sub-structure is used as frequency frontier between both sets of modes. From this classification, the equations of motion associated with global modes are derived, which include the interaction of local modes by means of corrections in the dynamic stiffness matrix and the force vector of the global problem. The local equations of motion are solved through SEA, where again interactions with global modes arc included through the inclusion of an additional input power into the SEA model. The method has been tested for the calculation of the response function of structures subjected to structural and acoustic loads. Both methods have been firstly tested in simple structures to establish their basis and main characteristics. Methods are also verified in space structures, as satellites and antenna reflectors, providing good results as it is concluded from the comparison with experimental results obtained in both, acoustic and structural load tests. This dissertation opens a wide field of research through which further studies could be performed to obtain efficient and accurate methodologies to appropriately reproduce the vibro-acoustic behaviour of complex systems in the mid-frequency range.

Sola romani: morteros hidráulicos romanos en la Península Ibérica

En esta investigación se han analizado morteros de cal de cronología romana en el interior de la Península Ibérica. Para ello, se seleccionó una serie de muestras procedentes de diversos yacimientos, y de estructuras de carácter industrial. Estas muestras presentan aditivos cerámicos y conglomerantes de cal, como característica principal. Desde un principio el esfuerzo debía de centrarse en los fragmentos cerámicos presentes en los morteros. Para ello se documentaron varios morteros con aditivos cerámicos, a fin de conocer sus características básicas (componentes, distribución, micro-estratigrafía, granulometría, etc.). Por ello, y una vez tomadas las muestras, ésta fueron tratadas y procesadas para desarrollar una primera fase de estudio por medio de macroscopía. Se obtuvieron buenos resultados en cuanto a la caracterización visual de los morteros, localizando y documentando los fragmentos cerámicos. Durante la observación de dichos aditivos se observó que los fragmentos cerámicos tenían unas coronas o anillos de coloración que recorrían el borde, justo al contacto con la matriz de cal. Fueron seleccionados algunos fragmentos en los que eran más visibles dichos anillos. A fin de conocer la posible relación entre algunos yacimientos cercanos y la presencia de dicho anillo cromáticos se desarrolló una microscopía óptica polarizada, realizando láminas delgadas de las muestras y sobre los fragmentos cerámicos más determinantes, en concreto de una serie de enclaves del valle del Henares. Además de caracterizar microscópicamente los morteros, se observó que los anillos no eran un defecto visual ni una alteración física, producida tal vez por la extracción, la fase del corte o por la cocción de la cerámica. Tras analizar varios ejemplares se pudo apreciar que esos anillos eran habituales en todas las muestras y que se presentaban de diferente manera, es decir, que se observaban en granos cerámicos de diferentes características físicas (cochura, tamaño, situación con respecto del conglomerante, etc.). A fin de conocer los aspectos químicos de dicha alteración se seleccionó un grupo de muestras en las que los resultados macroscópicos habían sido muy claros, y en las que la microscopía óptica polarizada había determinado en los bordes, áreas adecuadas para otros análisis. Se realizó un mapeado o mapping de elementos químicos, a fin de saber qué podía estar sucediendo en esa interfaz entre el fragmento cerámico y la matriz de cal. Gracias a los resultados obtenidos se comprobó que existía una acumulación potencial de calcio tanto en el interior de los granos cerámicos como en el exterior, justo en la zona de contacto con el conglomerante, formando manchas que recorrían longitudinalmente el borde. Estos datos fueron muy útiles para llevar a cabo la siguiente fase de estudio, que permitiría conocer puntualmente qué estaba sucediendo químicamente en esa zona de contacto. Finalmente y con el objetivo de describir química y puntualmente este efecto en las adiciones cerámicas, se volvió a seleccionar una serie de muestras, escogidas esta vez en función de los granos cerámicos que cumpliesen unas variables estadísticas. Se eligieron granos con distintos tipos de cocciones, así como granos con tamaños diversos y granos con aditivo ceniciento en la matriz de cal, pensando que podrían ser las variables más útiles de interpretar de existir algún tipo de cambio químico entre la arcilla cocida y la matriz de cal. Tales variables se adaptaron a un sistema estadístico multi-varial y geométrico, con el objetivo de sintetizar los resultados y visualizar de forma óptima los datos en conjunto, como se ha comentado en varias ocasiones en este trabajo. Una vez seleccionados los granos por variables se procedió a realizar un análisis lineal y espectral semi-cuantitativo de SEM-EDX, con el que se caracterizaba químicamente una sección lineal del grano, desde la matriz de arcilla cocida de la cerámica hasta la matriz de cal –del interior al exterior del grano- pasando por el centro de la banda de reacción. Este análisis permitió determinar que se había producido una serie de cambios químicos porcentuales en los granos de cerámica. Dichos cambios se resumen en un incremento global de los porcentajes de calcio en el interior de las bandas de reacción de la cerámica, desde el borde mismo del anillo hasta el exterior. Así también se observaron picos porcentuales en el interfaz del fragmento cerámico con la matriz de cal, lo que confirmaba los resultados obtenidos por medio del mapping. Globalmente en todas las muestras se apreció un hombro en las gráficas de calcio a su paso por la zona de afección del anillo de reacción. Los restantes porcentajes de magnesio, silicio y aluminio se mantienen normales. En esta tesis se ha confirmado que dicho incremento global de calcio se acentúa en las muestras en donde no hay cenizas en la matriz de cal. Los casos correspondientes a estos granos sufren un incremento mayor que en el resto. La segunda variable que sufre un mayor incremento de calcio es la que corresponde a granos con buena cocción de la arcilla. Por lo tanto, parece que la tercera variable, la que corresponde con el tamaño del fragmento cerámico, no es decisiva. Por lo tanto, teniendo en cuenta la prueba visual de los anillos de reacción, y atendiendo a los resultados químicos, podríamos pensar que ese incremento de calcio en la banda de reacción de los fragmentos cerámicos se debió a una absorción de calcio en el interior de la arcilla cocida en la fase inmediatamente previa al fraguado, incluso durante el apagado de la cal. Es en este punto donde estaría la clave del cambio químico que se produce en esta interfaz, el calcio sílice-aluminato del que algunos autores ya han investigado. Esta absorción de calcio en el interior del grano no vendría sola, sino que generaría una costra de cal en el interfaz exterior de la cerámica, la cual ha sido observada químicamente por mapping y mineralógicamente por medio de microscopía óptica de polarización. La consecuencia de estos resultados es, primero, la mejora de nuestro conocimiento general acerca del factor hidráulico en los morteros. Asimismo se aprecia que la incorporación de materiales orgánicos como cenizas, puede alterar los porcentajes de calcio en el interior de los aditivos cerámicos, por lo que habría que sopesar, en trabajos futuros, si este tipo de material es adecuado o no en las mezclas destinadas a la restauración, así como seguir indagando en las propiedades de los morteros con la incorporación de aditivos orgánicos. Desde el punto de vista de la catalogación de los suelos industriales hidráulicos de época romana, además de mejorar la documentación incorporando micro-estratigrafías y granulometrías, la investigación de este material histórico constructivo mejora en cuanto a que se incorporan ensayos sencillos, que facilitan incluso la peritación de un estado de conservación por medio de una lupa binocular. Arqueológicamente hablando, es muy interesante correlacionar fábricas diferentes de estructuras situadas o bien en un mismo yacimiento, o bien en una misma área regional. Los estudios de caracterización y micro-estratigrafía no sólo aportan datos nuevos de cara a la restauración de morteros, sino que crean la posibilidad de generar patrones constructivos que sirvan de fósiles-guía para datar relativamente a unas estructuras o a otras. En lo referido a los resultados obtenidos en los diferentes complejos arqueológicos se ha observado una diferencia entre los morteros destinados a piletas y cubetas con respecto a los suelos industriales de uso indeterminado. La muestra correspondiente al yacimiento de Las Arenas no dispone de ninguna micro-estratigrafía, como sí por el contrario en las muestras obtenidas en Rotonda de Mejorada, Val de la Viña y La Magdalena. En estos enclaves las estructuras presentan grandes similitudes, con diferentes niveles constructivos empleando morteros de cal con áridos y gravas en las capas interiores, y áridos con adiciones cerámicas en las exteriores. En lo relativo a la granulometría las adiciones cerámicas de las muestras de Val de la Viña y La Magdalena presentan varias coincidencias en cuanto al tamaño de los granos y la distribución. Asimismo, de las muestras tomadas en La Magdalena, existe una gran diferencia entre las muestras MG1, MG2, MG3 y MG4 con respecto a las muestras MG5 y MG6, correspondientes éstas últimas a un mortero con fragmentos cerámicos de gran tamaño. Las estructuras EMG1 y EMG2, correspondientes a una cubeta y una pileta de La Magdalena, guardan similitud en lo referido a la micro-estratigrafía y a la granulometría. Se ha determinado que su función, así como su fabricación, debieron estar vinculadas a un mismo contexto cronocultural. Química y mineralógicamente, las muestras presentan características iguales, con presencia de un conglomerante de cal con áridos y aditivos cerámicos de diferentes cochuras. Destaca la muestra de Las Arenas, con un tamaño de los fragmentos cerámicos muy superior al resto, seguido de la estructura EMG3 de La Magdalena. Las muestras restantes de éste enclave, junto con las muestras recogidas en Val de la Viña y Rotonda de Mejorada presentan condiciones similares. En conclusión, los datos revelan que existían diferentes fábricas destinadas a distintas finalidades, y que las estructuras industriales empleaban aditivos cerámicos para la manipulación de productos con líquidos, de distintas densidades pero que requerían de cierto grado de hidraulicidad. ABSTRACT Lime Roman mortars from the Iberian Peninsula has been analyzed in this reesearch. A group of samples were selected from some sites and all the samples come from industrial structures. All this samples show ceramic additives. From the start, the effort was centered in the pieces of pottery that were found in the mortars. The samples were treated and processed to develop a first phase of the research using macroscopy. With this technique, great results were achieved in the characterization of mortars, the microstratigraphy and the location of the ceramic pieces. While observing these pieces, it was seen that the fragments of pottery had a ring bordering the piece. The pieces with the bigger and more vivid rings were chosen and they were analyzed by a polarized light microscope. The mortars were characterized microscopically and it also showed that the rings were not a physical alteration or a visual defect. After some more tests, the rings were a chemical change associated with the hydraulicity of the mortar. The best samples were selected and mappings of their chemical elements were performed in order to know what could be happening in the interface between the ceramic matrix fragment and lime. With the results obtained it was found that there was a potential; both calcium accumulation within the ceramic grains and outside, just in the area of contact with the binder, forming spots longitudinally along the edge. These data were very useful for carrying out the next phase of study, which would meet promptly what was happening chemically in the area of contact. Another group of samples were taken, and this time focused on ceramic grains that met a statistical variables. Grains were chosen with two types of cooking as well as grains with different sizes and grains with ash additive in the matrix of lime, thinking that might be the most logical to be some sort of chemical change between the baked clay and lime array variables . Such variables were adapted to a multi-varial and geometric statistical system in order to synthesize the results and optimally display the data together, as mentioned several times in this work. After selecting the variables grains proceeded to perform a linear and spectral analysis SEM-EDX. This analysis led to determine that the chemical changes were graduals. These changes are summarized in an increase in the percentages of calcium inside the reaction rim of ceramics, from the edge to the outer ring. So percentage increasing is also observed at the interface of the ceramic matrix fragment with lime, confirming the results obtained by the mapping. Overall in all samples can be seen a shoulder in graphic calcium through the area of the ring reaction condition. The remaining percentages of magnesium, silicon and aluminum are usual. We have promptly confirmed that the increase of calcium is accentuated in samples where there is no ash and lime matrix. Cases for these grains suffer a greater increase than the rest. The second variable suffering more calcium is increased corresponding to good cooking grains with clay. Therefore, it appears that the variable size of the fragment is not critical. Therefore, considering the visual tests to the rings and their response to chemical results, we might think that increasing calcium inside the ceramic fragments was due to an injection of calcium inside clay in the run-up to the setting phase. It is at this point that would be the key to the chemical change that occurs at this interface, silica-calcium aluminate some authors have already investigated. This injection of calcium into the grain does not come alone, but generate a lime crust on the outside interface of ceramics, which we tested for mapping is real in our samples. The consequence of these results is the improvement of our understanding of historical hydraulic factor in building materials, such as mortar. For example, knowing that the incorporation of organic materials such as ash powder, may be detrimental to the injection of calcium inside the ceramic additives. Archaeologically speaking, it's very interesting to correlate different factories or structures located on a single site, or in the same regional area. Characterization studies and microstratigraphy not only provide new information to help restore mortars, but create the possibility of generating constructive patterns that serve as guide fossils to determinate the age of the structures. With regard to the results obtained in different archaeological sites it has seen a difference between mortars of pools or sinks with respect to industrial floors of undetermined use. The sample of the site of Las Arenas does not have any micro-stratigraphy, as if instead in the samples obtained in Rotonda de Mejorada, Val de la Viña and La Magdalena sites. In these settlements the structures are really similar, with different construction levels using lime mortars with aggregates and gravel in the inner layers, and ceramic aggregates as external additions. With regard to the grain size of the ceramic additions Val de la Viña and La Magdalena samples has several coincidences about the size of grains and distribution. Also, samples taken at La Magdalena, there is a difference between the MG1, MG2, MG3 and MG4 samples and the MG5 and MG6 samples, so the last corresponding to a mortar samples with larger ceramic fragments. The EMG1 and EMG2 structures, corresponding to a bucket and a pool of La Magdalena settlement, have similarities with regard to micro-stratigraphy and grain size. It has been determined that the function and manufacturing must be linked with a same chronocultural context.

On the Statistical Distribution of Object-Oriented System Properties

The statistical distributions of different software properties have been thoroughly studied in the past, including software size, complexity and the number of defects. In the case of object-oriented systems, these distributions have been found to obey a power law, a common statistical distribution also found in many other fields. However, we have found that for some statistical properties, the behavior does not entirely follow a power law, but a mixture between a lognormal and a power law distribution. Our study is based on the Qualitas Corpus, a large compendium of diverse Java-based software projects. We have measured the Chidamber and Kemerer metrics suite for every file of every Java project in the corpus. Our results show that the range of high values for the different metrics follows a power law distribution, whereas the rest of the range follows a lognormal distribution. This is a pattern typical of so-called double Pareto distributions, also found in empirical studies for other software properties.

A Multi-Agent System for the Solution of Fuzzy Incidents in Telecommunications

This article presents a multi-agent expert system (SMAF) , that allows the input of incidents which occur in different elements of the telecommunications area. SMAF interacts with experts and general users, and each agent with all the agents? community, recording the incidents and their solutions in a knowledge base, without the analysis of their causes. The incidents are expressed using keywords taken from natural language (originally Spanish) and their main concepts are recorded with their severities as the users express them. Then, there is a search of the best solution for each incident, being helped by a human operator using a distancenotions between them.

A Multiagent system model which suggests solutions to fuzzy incidents in the field of telecommunications

This article presents the model of a multi-agent system (SMAF), which objectives are the input of fuzzy incidents as the human experts express them with different severities degrees and the further search and suggestion of solutions. The solutions will be later confirm or not by the users. This model was designed, implemented and tested in the telecommunications field, with heterogeneous agents in a cooperative model. In the design, different abstract levels where considered, according to the agents? objectives, their ways to carry it out and the environment in which they act. Each agent is modeled with different spectrum of the knowledge base

The ciao module system: A new module system for prolog

Ciao Prolog incorporates a module system which allows sepárate compilation and sensible creation of standalone executables. We describe some of the main aspects of the Ciao modular compiler, ciaoc, which takes advantage of the characteristics of the Ciao Prolog module system to automatically perform sepárate and incremental compilation and efficiently build small, standalone executables with competitive run-time performance, ciaoc can also detect statically a larger number of programming errors. We also present a generic code processing library for handling modular programs, which provides an important part of the functionality of ciaoc. This library allows the development of program analysis and transformation tools in a way that is to some extent orthogonal to the details of module system design, and has been used in the implementation of ciaoc and other Ciao system tools. We also describe the different types of executables which can be generated by the Ciao compiler, which offer different tradeoffs between executable size, startup time, and portability, depending, among other factors, on the linking regime used (static, dynamic, lazy, etc.). Finally, we provide experimental data which illustrate these tradeoffs.

A system for automatically generating documentation for (C)LP programs

We describe lpdoc, a tool which generates documentation manuals automatically from one or more logic program source files, written in ISO-Prolog, Ciao, and other (C)LP languages. It is particularly useful for documenting library modules, for which it automatically generates a rich description of the module interface. However, it can also be used quite successfully to document full applications. A fundamental advantage of using lpdoc is that it helps maintaining a true correspondence between the program and its documentation, and also identifying precisely to what version of the program a given printed manual corresponds. The quality of the documentation generated can be greatly enhanced by including within the program text assertions (declarations with types, modes, etc.) for the predicates in the program, and machine-readable comments. One of the main novelties of lpdoc is that these assertions and comments are written using the Ciao system assertion language, which is also the language of communication between the compiler and the user and between the components of the compiler. This allows a significant synergy among specification, documentation, optimization, etc. A simple compatibility library allows conventional (C)LP systems to ignore these assertions and comments and treat normally programs documented in this way. The documentation can be generated in many formats including texinfo, dvi, ps, pdf, info, html/css, Unix nroff/man, Windows help, etc., and can include bibliographic citations and images. lpdoc can also generate “man” pages (Unix man page format), nicely formatted plain ascii “readme” files, installation scripts useful when the manuals are included in software distributions, brief descriptions in html/css or info formats suitable for inclusion in on-line indices of manuals, and even complete WWW and info sites containing on-line catalogs of documents and software distributions. The lpdoc manual, all other Ciao system manuals, and parts of this paper are generated by lpdoc.

Distributed System for Cognitive Stimulation Over Interactive TV.

Descripción y evaluación de sistema de estimulación cognitiva a través de la TDT orientada a personas con enfermedad de Parkinson, con supervisión por parte de sus terapeutas de forma remota. Abstract: This paper details the full design, implementation, and validation of an e-health service in order to improve the community health care services for patients with cognitive disorders. Specifically, the new service allows Parkinson’s disease patients benefit from the possibility of doing cognitive stimulation therapy (CST) at home by using a familiar device such as a TV set. Its use instead of a PC could be a major advantage for some patients whose lack of familiarity with the use of a PC means that they can do therapy only in the presence of a therapist. For these patients this solution could bring about a great improvement in their autonomy. At the same time, this service provides therapists with the ability to conduct follow-up of therapy sessions via the web,benefiting from greater and easier control of the therapy exercises performed by patients and allowing them to customize new exercises in accordance with the particular needs of each patient. As a result, this kind of CST is considered to be a complement of other therapies oriented to the Parkinson patients. Furthermore, with small changes, the system could be useful for patients with a different cognitive disease such as Alzheimer’s or mild cognitive impairment.

Is Europe ready to provide a pan-European Identity Management System?

European public administrations must manage citizens' digital identities, particularly considering interoperability among different countries. Owing to the diversity of electronic identity management (eIDM) systems, when users of one such system seek to communicate with governments using a different system, both systems must be linked and understand each other. To achieve this, the European Union is working on an interoperability framework. This article provides an overview of eIDM systems' current state at a pan-European level. It identifies and analyzes issues on which agreement exists, as well as those that aren't yet resolved and are preventing the adoption of a large-scale model.

Approach to integrate product conceptual design information into a computer-aided design system

Commercial computer-aided design systems support the geometric definition of product, but they lack utilities to support initial design stages. Typical tasks such as customer need capture, functional requirement formalization, or design parameter definition are conducted in applications that, for instance, support ?quality function deployment? and ?failure modes and effects analysis? techniques. Such applications are noninteroperable with the computer-aided design systems, leading to discontinuous design information flows. This study addresses this issue and proposes a method to enhance the integration of design information generated in the early design stages into a commercial computer-aided design system. To demonstrate the feasibility of the approach adopted, a prototype application was developed and two case studies were executed.

Sentence selection for improving the tuning process of a statistical machine translation system

Este artículo describe una estrategia de selección de frases para hacer el ajuste de un sistema de traducción estadístico basado en el decodificador Moses que traduce del español al inglés. En este trabajo proponemos dos posibilidades para realizar esta selección de las frases del corpus de validación que más se parecen a las frases que queremos traducir (frases de test en lengua origen). Con esta selección podemos obtener unos mejores pesos de los modelos para emplearlos después en el proceso de traducción y, por tanto, mejorar los resultados. Concretamente, con el método de selección basado en la medida de similitud propuesta en este artículo, mejoramos la medida BLEU del 27,17% con el corpus de validación completo al 27,27% seleccionando las frases para el ajuste. Estos resultados se acercan a los del experimento ORACLE: se utilizan las mismas frases de test para hacer el ajuste de los pesos. En este caso, el BLEU obtenido es de 27,51%.

Commonalities between networking in multiplayer computer games and negotiation processes in a future multi-layered Air Traffic Management (ATM) system

First, this paper describes a future layered Air Traffic Management (ATM) system centred in the execution phase of flights. The layered ATM model is based on the work currently performed by SESAR [1] and takes into account the availability of accurate and updated flight information ?seen by all? across the European airspace. This shared information of each flight will be referred as Reference Business Trajectory (RBT). In the layered ATM system, exchanges of information will involve several actors (human or automatic), which will have varying time horizons, areas of responsibility and tasks. Second, the paper will identify the need to define the negotiation processes required to agree revisions to the RBT in the layered ATM system. Third, the final objective of the paper is to bring to the attention of researchers and engineers the communalities between multi-player games and Collaborative Decision Making processes (CDM) in a layered ATM system

Structural health monitoring network system with wireless communications inside closed aerospace structures

Structural Health Monitoring (SHM) requires integrated "all in one" electronic devices capable of performing analysis of structural integrity and on-board damage detection in aircraft?s structures. PAMELA III (Phased Array Monitoring for Enhanced Life Assessment, version III) SHM embedded system is an example of this device type. This equipment is capable of generating excitation signals to be applied to an array of integrated piezoelectric Phased Array (PhA) transducers stuck to aircraft structure, acquiring the response signals, and carrying out the advanced signal processing to obtain SHM maps. PAMELA III is connected with a host computer in order to receive the configuration parameters and sending the obtained SHM maps, alarms and so on. This host can communicate with PAMELA III through an Ethernet interface. To avoid the use of wires where necessary, it is possible to add Wi-Fi capabilities to PAMELA III, connecting a Wi-Fi node working as a bridge, and to establish a wireless communication between PAMELA III and the host. However, in a real aircraft scenario, several PAMELA III devices must work together inside closed structures. In this situation, it is not possible for all PAMELA III devices to establish a wireless communication directly with the host, due to the signal attenuation caused by the different obstacles of the aircraft structure. To provide communication among all PAMELA III devices and the host, a wireless mesh network (WMN) system has been implemented inside a closed aluminum wingbox. In a WMN, as long as a node is connected to at least one other node, it will have full connectivity to the entire network because each mesh node forwards packets to other nodes in the network as required. Mesh protocols automatically determine the best route through the network and can dynamically reconfigure the network if a link drops out. The advantages and disadvantages on the use of a wireless mesh network system inside closed aerospace structures are discussed.

Integrated electronic system for ultrasonic structural health monitoring

A fully integrated on-board electronic system that can perform in-situ structural health monitoring (SHM) of aircraft?s structures using specifically designed equipment for SHM based on guided wave ultrasonic method or Lamb waves? method is introduced. This equipment is called Phased Array Monitoring for Enhanced Life Assessment (PAMELA III) and is an essential part of overall PAMELA SHM? system. PAMELA III can generate any kind of excitation signals, acquire the response signals that propagate throughout the structure being tested, and perform the signal processing for damage detection directly on the structure without need to send the huge amount of raw signals but only the final SHM maps. It monitors the structure by means of an array of integrated Phased Array (PhA) transducers preferably bonded onto the host structure. The PAMELA III hardware for SHM mapping has been designed, built and subjected to laboratory tests, using aluminum and CFRP structures. The 12 channel system has been designed to be low weight (265 grams only), to have a small form factor, to be directly mounted above the integrated PhA transducers without need for cables and to be EMI protected so that the equipment can be taken on board an aircraft to perform required SHM analyses by use of embedded SHM algorithms. Moreover, the autonomous, automatic and on real-time working procedure makes it suitable for the avionic field, sending the corresponding alerts, maps and reports to external equipment.

A quality assessment system for fresh fruits in hypermarkets and fruit trading centres.

When the fresh fruit reaches the final markets from the suppliers, its quality is not always as good as it should, either because it has been mishandled during transportation or because it lacks an adequate quality control at the producer level, before being shipped. This is why it is necessary for the final markets to establish their own quality assessment system if they want to ensure to their customers the quality they want to sell. In this work, a system to control fruit quality at the last level of the distribution channel has been designed. The system combines rapid control techniques with laboratory equipment and statistical sampling protocols, to obtain a dynamic, objective process, which can substitute advantageously the quality control inspections carried out visually by human experts at the reception platform of most hypermarkets. Portable measuring equipment have been chosen (firmness tester, temperature and humidity sensors...) as well as easy-to-use laboratory equipment (texturometer, colorimeter, refractometer..,) combining them to control the most important fruit quality parameters (firmness, colour, sugars, acids). A complete computer network has been designed to control all the processes and store the collected data in real time, and to perform the computations. The sampling methods have been also defined to guarantee the confidence of the results. Some of the advantages of a quality assessment system as the proposed one are: the minimisation of human subjectivity, the ability to use modern measuring techniques, and the possibility of using it also as a supplier's quality control system. It can be also a way to clarify the quality limits of fruits among members of the commercial channel, as well as the first step in the standardisation of quality control procedures.