Epitaxial self-alignment: A new route to hybrid active plasmonic nanostructures

Concepts of lateral ordering of epitaxial semiconductor quantum dots (QDs) are for the first time transferred to hybrid nanostructures for active plasmonics. We review our recent research on the self-alignment of epitaxial nanocrystals of In and Ag on ordered one-dimensional In(Ga)As QD arrays and isolated QDs by molecular beam epitaxy. By changing the growth conditions the size and density of the metal nanocrystals are easily controlled and the surface plasmon resonance wavelength is tuned over a wide range in order to match the emission wavelength of the QDs. Photoluminescence measurements reveal large enhancement of the emitted light intensity due to plasmon enhanced emission and absorption down to the single QD level.

Degradation in seawater of structural adhesives for hybrid fibre-metal laminated materials

The adhesives used for applications in marine environments are subject to particular chemical conditions, which are mainly characterised by an elevated chlorine ion content and intermittent wetting/drying cycles, among others.These conditions can limit the use of adhesives due to the degradation processes that they experience. In this work, the chemical degradation of two different polymers, polyurethane and vinylester, was studied in natural seawater under immersion for different periods of time.The diffusion coefficients and concentration profiles of water throughout the thickness of the adhesiveswere obtained.Microstructural changes in the polymer due to the action of water were observed by SEM, and the chemical degradation of the polymer was monitored with the Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC). The degradation of the mechanical properties of the adhesive was determined by creep tests withMixed Cantilever Beam (MCB) specimens at different temperatures. After 180 days of immersion of the specimens, it was concluded that the J-integral value (depending on the strain) implies a loss of stiffness of 51% and a decrease in the failure load of 59% for the adhesive tested.

Self-organized colloidal quantum dots and metal nanoparticles for plasmon-enhanced intermediate-band solar cells

A colloidal deposition technique is presented to construct long-range ordered hybrid arrays of self-assembled quantum dots and metal nanoparticles. Quantum dots are promising for novel opto-electronic devices but, in most cases, their optical transitions of interest lack sufficient light absorption to provide a significant impact in their implementation. A potential solution is to couple the dots with localized plasmons in metal nanoparticles. The extreme confinement of light in the near-field produced by the nanoparticles can potentially boost the absorption in the quantum dots by up to two orders of magnitude. In this work, light extinction measurements are employed to probe the plasmon resonance of spherical gold nanoparticles in lead sulfide colloidal quantum dots and amorphous silicon thin-films. Mie theory computations are used to analyze the experimental results and determine the absorption enhancement that can be generated by the highly intense near-field produced in the vicinity of the gold nanoparticles at their surface plasmon resonance. The results presented here are of interest for the development of plasmon-enhanced colloidal nanostructured photovoltaic materials, such as colloidal quantum dot intermediate-band solar cells.

Computer simulation of random parckings for self-similar particle size distributions in soil and granular materials: porosity and pore size distribution

A 2D computer simulation method of random packings is applied to sets of particles generated by a self-similar uniparametric model for particle size distributions (PSDs) in granular media. The parameter p which controls the model is the proportion of mass of particles corresponding to the left half of the normalized size interval [0,1]. First the influence on the total porosity of the parameter p is analyzed and interpreted. It is shown that such parameter, and the fractal exponent of the associated power scaling, are efficient packing parameters, but this last one is not in the way predicted in a former published work addressing an analogous research in artificial granular materials. The total porosity reaches the minimum value for p = 0.6. Limited information on the pore size distribution is obtained from the packing simulations and by means of morphological analysis methods. Results show that the range of pore sizes increases for decreasing values of p showing also different shape in the volume pore size distribution. Further research including simulations with a greater number of particles and image resolution are required to obtain finer results on the hierarchical structure of pore space.

Self-consistent relativistic band structure of the CH3NH3PbI3 perovskite

The electronic structure and properties of the orthorhombic phase of the CH 3 NH 3 PbI 3 perovskite are computed with density functional theory. The structure, optimized using a van der Waals functional, reproduces closely the unit cell volume. The experimental band gap is reproduced accurately by combining spin-orbit effects and a hybrid functional in which the fraction of exact exchange is tuned self-consistently to the optical dielectric constant. Including spin-orbit coupling strongly reduces the anisotropy of the effective mass tensor, predicting a low electron effective mass in all crystal directions. The computed binding energy of the unrelaxed exciton agrees with experimental data, and the values found imply a fast exciton dissociation at ambient temperature. Also polaron masses for the separated carriers are estimated. The values of all these parameters agree with recent indications that fast dynamics and large carrier diffusion lengths are key in the high photovoltaic efficiencies shown by these materials.

Polypropylene fiber-reinforced self-compacting concrete for the reconstruction of the cathedral of La Laguna, Canary Island, Spain

High performance materials are needed for the reconstruction of such a singular building as a cathedral, since in addition to special mechanical properties, high self compact ability, high durability and high surface quality, are specified. Because of the project’s specifications, the use of polypropylene fiber-reinforced, self-compacting concrete was selected by the engineering office. The low quality of local materials and the lack of experience in applying macro polypropylene fiber for structural reinforcement with these components materials required the development of a pretesting program. To optimize the mix design, performance was evaluated following technical, economical and constructability criteria. Since the addition of fibers reduces concrete self-compactability, many trials were run to determine the optimal mix proportions. The variables introduced were paste volume; the aggregate skeleton of two or three fractions plus limestone filler; fiber type and dosage. Two mix designs were selected from the preliminary results. The first one was used as reference for self-compactability and mechanical properties. The second one was an optimized mix with a reduction in cement content of 20 kg/m3and fiber dosage of 1 kg/m3. For these mix designs, extended testing was carried out to measure the compression and flexural strength, modulus of elasticity, toughness, and water permeability resistance

Evaluation of the mechanical properties of self compacting concrete using current estimating models. Estimating the modulus of elasticity, tensile strength, and modulus of rupture of self compacting concrete

This study includes an analysis of the applicability of current models used for estimating the mechanical properties of conventional concrete to self-compacting concrete. The mechanical properties evaluated are: modulus of elasticity, tensile strength, and modulus of rupture. An extensive database which included the dosifications and the mechanical properties of 627 mixtures from 138 different references, was used. The models considered are: ACI, EC-2, NZS 3101:2006 (New Zealand code) and the CSA A23.3-04 (Canadian code). The precision in estimating the modulus of elasticity and tensile strength is acceptable for all models; however, all models are less precise in estimating the modulus of rupture.

Understanding the Selective Area Nucleation and Growth of GaN nanocolumns by MBE using Ti nanomasks

•Self- assembled Ga(In)N Nanorods and Nanostructures •Ordered growth of GaN Nanorods: masks issues •Ordered growth of GaN Nanorods: mechanisms •White NanoLEDs

MBE growth and characterization of InGaN-based films and nanocolumns on Silicon substrates and GaN templates

InN layers: MBE growth issues Growth of InN-based thin films: InN/InGaN QWS on GaN Growth of InN-based nanorods ● Self Self-assembled assembled InN InN nanorods nanorods onon different different substrates substrates ● Self-assembled InGaN nanorods ● Broad- Broad-emission emission nanostructures ● Self Self--assembled assembled InGaN InGaN--based based Qdisks Qdisks ● Selective area growth (SAG) of InGaN Qdisks

Estudio de las formas de aplicación de la fotografía sobre los materiales pétreos para la arquitectura = Study of photography application methods over architectural stony materials

Desde que el Hombre era morador de las cavernas ha sido manifiesto su deseo innato por grabar y reproducir "instantáneas con las que perpetuarse o sobre las que mirarse ". La aparición y desarrollo de la fotografía como medio para poder captar y fijar "la imagen directa de la realidad circundante " pronto se convierte en un nuevo lenguaje estético y poético que permite al artista la interpretación y reflexión de lo observado. Se imprime a la imagen el carácter de la mirada del fotógrafo, estableciendo un diálogo conceptual con el juego de luces. La presente Tesis plantea la creación de una nueva piel de arquitectura mediante la impresión fotográfica sobre materiales pétreos. La búsqueda de la expresividad de los materiales como soporte de expresión artística implica un cambio de escala al trasladar la instantánea fotográfica a la arquitectura y la aplicación de un nuevo soporte al imprimir la fotografía sobre materiales arquitectónicos. Se justifica la elección del dispositivo láser CO2 como sistema de impresión fotográfica sobre los materiales pétreos arquitectónicos, como la técnica que permite la unión física de la imagen y el proyecto arquitectónico, generando un valor añadido a través del arte de la fotografía. Se justifica la elección de los materiales investigados, Silestone® Blanco Zeus y GRC® con TX Active® Aria, de forma que la investigación de esta nueva piel de arquitectura abarca tanto la envolvente del edificio como su volumen interior, permitiendo cerrar el círculo arquitectónico "in&out" y dota al proyecto arquitectónico de un valor añadido al introducir conceptos sostenibles de carácter estético y medioambiental. Se realiza una consulta a las empresas del sector arquitectónico relacionadas directamente con la producción y distribución de los materiales Silestone® y GRC®, así como a las empresas especializadas en sistemas de impresión fotográfica sobre materiales, acerca del estado del arte. Se recorre la Historia de la fotografía desde sus orígenes hasta el desarrollo de la era digital y se analiza su condición artística. Se recopilan los sistemas de impresión fotográfica que han evolucionado en paralelo con los dispositivos de captura de la instantánea fotográfica y se describe en profundidad el sistema de impresión fotográfica mediante dispositivo láser CO2. Se describen los procesos de fabricación, las características técnicas, cualidades y aplicaciones de los materiales pétreos arquitectónicos Silestone® Blanco Zeus y GRC® con TX Active® Aria. Se explica la técnica utilizada para la captación de la imagen fotográfica, su justificación artística y su proceso de impresión mediante dispositivo láser CO2 bajo diferentes parámetros sobre muestras de los materiales arquitectónicos investigados. Se comprueba la viabilidad de desarrollo de la nueva piel de arquitectura sobre Silestone® Blanco Zeus y GRC® con TX Active® Aria sometiendo a las piezas impresas bajo diferentes parámetros a tres ensayos de laboratorio. En cada uno de ellos se concreta el objetivo y procedimiento del ensayo, la enumeración de las muestras ensayadas y los parámetros bajo los que han sido impresas, el análisis de los resultados del ensayo y las conclusiones del ensayo. Ensayo de amplitud térmica. Se determina el grado de afectación de las imágenes impresas bajo la acción de contrastes térmicos. Series de muestras de Silestone® Blanco Zeus y GRC® con TX Active® Aria impresas con láser CO2 se someten a ciclos de contraste frío-calor de 12 horas de duración para una amplitud térmica total de 102°C. Se realiza una toma sistemática de fotografías microscópicas con lupa de aumento de cada pieza antes y después de los ciclos frío-calor y la observación de las transformaciones que experimentan los materiales bajo la acción del láser CO2. Ensayo de exposición a la acción de la radiación ultravioleta (UV). Se determina el grado de afectación de las imágenes impresas al activar la capacidad autolimpiante de partículas orgánicas. Una serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a ciclos de exposición de radiación ultravioleta de 26 horas de duración. Se somete la serie a un procedimiento de activación del aditivo TX Active®. Se simula la contaminación orgánica mediante la aplicación controlada de Rodamina B, tinte orgánico, y se simula la radiación UV mediante el empleo de una bombilla de emisión de rayos ultravioleta. Se realiza una toma sistemática de fotografías macroscópicas de la serie de muestras ensayadas: antes de aplicación de la Rodamina B, momento 00:00h, momento 04:00h y momento 26:00h del ensayo. Se procede a la descarga y análisis del histograma de las fotografías como registro de la actividad fotocatalítica. Ensayo de la capacidad autodescontaminante del GRC® con TX Active® impreso con láser CO2. Se comprueba si la capacidad autodescontaminante del GRC® con TX Active® se ve alterada como consecuencia de la impresión de la imagen fotográfica impresa con láser CO2. Serie de muestras de GRC® con TX Active® Aria impresa con láser CO2 se someten a test de capacidad autodescontaminante: atmósfera controlada y contaminada con óxidos de nitrógeno en los que se coloca cada pieza ensayada bajo la acción de una lámpara de emisión de radiación ultravioleta (UV). Se registra la actividad fotocatalítica en base a la variación de concentración de óxido de nitrógeno. Se recopila el análisis e interpretación de los resultados de los ensayos de laboratorio y se elaboran las conclusiones generales de la investigación. Se sintetizan las futuras líneas de investigación que, a partir de las investigaciones realizadas y de sus conclusiones generales, podrían desarrollarse en el ámbito de la impresión fotográfica sobre materiales arquitectónicos. Se describe el rendimiento tecnológico y artístico generado por las investigaciones previas que han dado origen y desarrollo a la Tesis Doctoral. ABSTRACT Since ancient time, humanity has been driven by an innate wish to reproduce and engrave "snapshots that could help to perpetúate or to look at one self". Photography's birth and its development as a mean to capture and fix "the direct image of the surrounding reality" quickly becomes a new aesthetical and poetical language allowing the artist to interpret and think over what has been observed. The photographer's eye is imprinted onto the image, and so the conceptual dialogue between the artist and the light beams begins. The current thesis suggests the creation of a new architectural skin through photography imprinting over stony materials. The search for material's expressiveness as a medium of artistic expression involves a change of scale as it transfers photographic snapshot into architecture and the use of a new photographic printing support over architectural materials. CO2 laser is the chosen printing system for this technique as it allows the physical union of the image and the architectonic project, generating an added value through the art of photography. The researched materials selected were Silestone®, Blanco Zeus and GRC® with TX Active® Aria. This new architectural skin contains the building surrounding as well as its interior volume, closing the architectonic "in & out" circle and adding a value to the project by introducing aesthetical and environmental sustainable concepts. Architecture companies related to the production and distribution of materials like Silestone® and GRC®, as well as companies specialized in photography printing over materials were consulted to obtain a State of the Art. A thorough analysis of photography's History from its origins to the digital era development was made and its artistic condition was studied in this thesis. In this study the author also makes a compilation of several photographic printing systems that evolved together with photographic snapshot devices. The CO2 laser-based photographic printing system is also described in depth. Regarding stony materials of architecture like Silestone®, Blanco Zeus and GRC® with TX Active® Aria, the present study also describes their manufacture processes as well as technical features, quality and application. There is also an explanation about the technique to capture the photographic image, its artistic justification and its CO2 laser-based printing system over the researched materials under different parameters. We also tested the feasibility of this new architectural skin over Silestone® Blanco Zeus and GRC® with TX Active® Aria. The pieces were tested under different parameters in three laboratory trials. Each trial comprises of an explanation of its objective and its process, the samples were numbered and the printing parameters were specified. Finally, with the analysis of the results some conclusions were drawn. In the thermal amplitude trial we tried to determine how printed images were affected as a result of the action of thermal contrasts. Series of samples of Silestone® Blanco Zeus and GRC® with TX Active® Aria printed with CO2 laser were subjected to several 12h warm-cold cycles for thermal total amplitude of 102oc. Each sample was captured systematically with microscopic enhanced lenses before and after cold-warm cycles. The changes experienced by these materials under the effect of CO2 laser were observed and recorded. Trial regarding the Ultraviolet Radiation (UR) effect on images. We determined to which extent printed images were affected once the self-cleaning organic particles were activated. This time GRC® with TX Active® Aria samples printed with CO2 laser were exposed to a 26h UR cycle. The samples were subjected to the activation of TX Active® additive. Through the controlled application of Rodamine B and organic dye we were able to simulate the organic contamination process. UR was simulated using an ultraviolet beam emission bulb. A systematic capture of macroscopic pictures of the tested sample series was performed at different time points: before Rodamine B application, at moment 00:00h, moment 04:00h and moment 26:00h of the trial. Picture's histogram was downloaded and analyzed as a log of photocatalytic activity. Trial regarding the self-decontaminating ability of GRC® with TX Active® printed with CO2 laser. We tested if this self-decontaminating ability is altered as a result of CO2 laser printed image. GRC® with TX Active® Aria samples printed with CO2 laser, were subject to self-decontaminating ability tests with controlled and nitrogen oxide contaminated atmosphere. Each piece was put under the action of an UR emission lamp. Photocatalytic activity was recorded according to the variation in nitrogen oxide concentration. The results of the trial and their interpretation as well as the general conclusions of the research are also compiled in the present study. Study conclusions enable to draw future research lines of potential applications of photographic printing over architecture materials. Previous research generated an artistic and technological outcome that led to the development of this doctoral thesis.

Mechanical properties of self-consolidating concrete using conventional concrete models

The objective of this study is to analyze the applicability of current models used for estimating the mechanical properties of conventional concrete to self-consolidating concrete (SCC). The mechanical properties evaluated are modulus of elasticity, tensile strength,and modulus of rupture. As part of the study, it was necessary to build an extensive database that included the proportions and mechanical properties of 627 mixtures from 138 different references. The same models that are currently used for calculating the mechanical properties of conventional concrete were applied to SCC to evaluate their applicability to this type of concrete. The models considered are the ACI 318, ACI 363R, and EC2. These are the most commonly used models worldwide. In the first part of the study, the overall behavior and adaptability of the different models to SCC is evaluated. The specific characterization parameters for each concrete mixture are used to calculate the various mechanical properties applying the different estimation models. The second part of the analysis consists of comparing the experimental results of all the mixtures included in the database with the estimated results to evaluate the applicability of these models to SCC. Various statistical procedures, such as regression analysis and residual analysis, are used to compare the predicted and measured properties. It terms of general applicability, the evaluated models are suitable for estimating the modulus of elasticity, tensile strength, and modulus of rupture of SCC. These models have a rather low sensitivity, however, and adjust well only to mean values. This is because the models use the compressive strength as the main variable to characterize the concrete and do not consider other variables that affect these properties.

Fabrication of luminescent nanostructures by electron-beam direct writing of PMMA resist

We report on the conversion of non-luminescent conventional poly(methylmethacrylate) (PMMA)-based electron-beam resists into luminescent materials when used as negative-tone resists, that is, when exposed to high electron irradiation doses. Raman spectroscopy reveals the chemical transformation induced by electron irradiation which is responsible for the observed luminescence in the visible (blue) region. The emission intensity from exposed PMMA-based patterns can be controlled by the electron irradiation dose employed to create them.

Assessment of self-combustion risks for solid fuels (POSTER)

Every solid fuel has a tendency to react with oxygen, a fact that constitutes the basis of their ability to oxidation and energy intake for combustion, but that poses a risk when it occurs in an uncontrolled manner. When the slow oxidation phenomenon produces more heat than can be evacuated, the result is a heating process, which promotes combustion reactions, primarily fuel oxidation, and a progressive increase in temperature.

Self-beating instabilities in bistable devices

Since the observation of optical bistability by Gibbs et al., optical bistability has been the field where researchers from many fields have found a common place to work. More recently, when Ikeda and co-workers discussed the effect of a delayed feedback on instability of a ring cavity containing a non linear dielectric medium, and pointed out that the transmitted light from the ring cavity can be periodic or chaotic in time under a certain condition, optical bistable devices have shown new possibilities to be applied in many different fields. The novel phenomenon has been predicted to be observed in the hybrid optical device and has been confirmed by Gibbs et al. Moreover, as we have shown, a similar effect can be obtained when liquid crystal cells are employed as non linear element.

Synthetic strategy of porous ZnO and CdS nanostructures doped ferroelectric liquid crystal and its optical behavior

A simple and scalable chemical approach has been proposed for the generation of 1-dimensional nanostructures of two most important inorganic materials such as zinc oxide and cadmium sulfide. By controlling the growth habit of the nanostructures with manipulated reaction conditions, the diameter and uniformity of the nanowires/nanorods were tailored. We studied extensively optical behavior and structural growth of CdS NWs and ZnO NRs doped ferroelectric liquid crystal Felix-017/100. Due to doping band gap has been changed and several blue shifts occurred in photoluminescence spectra because of nanoconfinement effect and mobility of charges.