Deep levels in a-plane, high Mg-content MgxZn1-xO epitaxial layers grown by molecular beam epitaxy

Deep level defects in n-type unintentionally doped a-plane MgxZn1−xO, grown by molecular beam epitaxy on r-plane sapphire were fully characterized using deep level optical spectroscopy (DLOS) and related methods. Four compositions of MgxZn1−xO were examined with x = 0.31, 0.44, 0.52, and 0.56 together with a control ZnO sample. DLOS measurements revealed the presence of five deep levels in each Mg-containing sample, having energy levels of Ec − 1.4 eV, 2.1 eV, 2.6 V, and Ev + 0.3 eV and 0.6 eV. For all Mg compositions, the activation energies of the first three states were constant with respect to the conduction band edge, whereas the latter two revealed constant activation energies with respect to the valence band edge. In contrast to the ternary materials, only three levels, at Ec − 2.1 eV, Ev + 0.3 eV, and 0.6 eV, were observed for the ZnO control sample in this systematically grown series of samples. Substantially higher concentrations of the deep levels at Ev + 0.3 eV and Ec − 2.1 eV were observed in ZnO compared to the Mg alloyed samples. Moreover, there is a general invariance of trap concentration of the Ev + 0.3 eV and 0.6 eV levels on Mg content, while at least and order of magnitude dependency of the Ec − 1.4 eV and Ec − 2.6 eV levels in Mg alloyed samples.

Influence of high aluminium content on the mechanical properties of directionally solidified multicrystalline silicon

The purpose of this research is the mechanical characterisation of multicrystalline silicon crystallised from silicon feedstock with a high content of aluminium for photovoltaic applications. The mechanical strength, fracture toughness and elastic modulus were measured at different positions within the multicrystalline silicon block to quantify the impact of the segregation of impurities on these mechanical properties. Aluminium segregated to the top of the block and caused extensive micro-cracking of the silicon matrix due to the thermal mismatch between silicon and the aluminium inclusions. Silicon nitride inclusions reduced the fracture toughness and caused failure by radial cracking in its surroundings due to its thermal mismatch with silicon. However, silicon carbide increased the fracture toughness and elastic modulus of silicon.

Influence of the semantic content of urban sounds in the identity of outer spaces

This paper shows the influence of the semantic content of urban sounds in the subjective evaluation of outer spaces. The study is based on the analysis conducted in three neighboring and integrated urban spaces with a different form of social ownership in the city of Cordoba, Argentina. It shows that the type of sound source present at each site influence, by its semantic content, in the user´s identification and permanence in the place. The noise present in a soundscape is able to have a high semantic content, and therefore the sound has a particular meaning for the perceiver. Every particular social group influences the production of their own sounds and how they perceive them. This allows to consider the sound as one of the factors that define the sense of "place" or "no place" of a certain urban space. Evidently the sounds, and their ability to evoke and characterize the environment, cannot be ignored in the construction and recovery of anthropological sites. This urban culture is unique and specific to every society. Thepublic spaces, with their soundscape, are part of the construction of the urban identity of a city. It is shown that for identical general sound levels present in each of the spaces, the level of annoyance or discomfort, in relation to the subjective acoustic quality, is different. This is the result of the influence of semantic content of the sounds present in each urban space. Coinciding with other similar research, the level of discomfort or annoyance decreases as the presence of natural sounds such as water, the wind in the trees or the birds singing increases, even when the objective values of noise level of natural sounds are higher.

Identifying yeats belonging to the Brettanomyces/Dekkera genera through the use of selective-differential media

The purpose of this work was to compare and optimise different selective and differential media to aid in isolating spoilage yeasts belonging to the Brettanomyces/Dekkera genera. Growth media containing selective and differential factors were employed. These were inoculated with strains of yeast representing Spanish oenological microbiota. Lastly, some of these isolation media were successfully applied in 24 types of wine with a high ethylphenol content, all of which were from the Haro Oenological Station (La Rioja, Spain). p-coumaric acid was determined using High performance liquid chromatography-photodiode-array detection-electrospray ionization mass spectrometry (HPLC-DAD-ESI/MS); 4-ethylphenol by using Solid phase micro extraction-gas chromatography-mass spectrometry (SPME-GC-MS); and the rest of the analysis was carried out using official OIV methodology. Actidione is the most effective selective factor for isolating Brettanomyces/Dekkera yeast genera. Other secondary selective factors (selective carbon sources, sorbic acid and ethanol as a microbicide agent) may be used successfully to eliminate potential false positivities; however, they slow growth and delay the time to obtain results.

Study of the effect of four warm mix asphalt additives on bitumen modified with 15% crumb rubber

Due to a growing concern over global warming, the bituminous mixture industry is making a constant effort to diminish its emissions by reducing manufacturing and installation temperatures without compromising the mechanical properties of the bituminous mixtures. The use of mixtures with tyre rubber has demonstrated that these mixtures can be economical and ecological and that they improve the behaviour of the pavements. However, bituminous mixtures with a high rubber content present one major drawback: they require higher mixing and installation temperatures due to the elevated viscosity caused by the high rubber content and thus they produce larger amounts of greenhouse gas emissions than conventional bituminous mixtures. This article presents a study of the effect of four viscosity-reducing additives (Sasobit®, Asphaltan A®, Asphaltan B® and Licomont BS 100®) on a bitumen modified with 15% rubber. The results of this study indicate that these additives successfully reduce viscosity, increase the softening temperature and reduce penetration. However, they do not have a clear effect on the test for elastic recovery and ductility at 25 °C.

Direct and adjoint global stability analysis of turbulent transonic flows over a NACA0012 profile

In this work, various turbulent solutions of the two-dimensional (2D) and three-dimensional compressible Reynolds averaged Navier?Stokes equations are analyzed using global stability theory. This analysis is motivated by the onset of flow unsteadiness (Hopf bifurcation) for transonic buffet conditions where moderately high Reynolds numbers and compressible effects must be considered. The buffet phenomenon involves a complex interaction between the separated flow and a shock wave. The efficient numerical methodology presented in this paper predicts the critical parameters, namely, the angle of attack and Mach and Reynolds numbers beyond which the onset of flow unsteadiness appears. The geometry, a NACA0012 profile, and flow parameters selected reproduce situations of practical interest for aeronautical applications. The numerical computation is performed in three steps. First, a steady baseflow solution is obtained; second, the Jacobian matrix for the RANS equations based on a finite volume discretization is computed; and finally, the generalized eigenvalue problem is derived when the baseflow is linearly perturbed. The methodology is validated predicting the 2D Hopf bifurcation for a circular cylinder under laminar flow condition. This benchmark shows good agreement with the previous published computations and experimental data. In the transonic buffet case, the baseflow is computed using the Spalart?Allmaras turbulence model and represents a mean flow where the high frequency content and length scales of the order of the shear-layer thickness have been averaged. The lower frequency content is assumed to be decoupled from the high frequencies, thus allowing a stability analysis to be performed on the low frequency range. In addition, results of the corresponding adjoint problem and the sensitivity map are provided for the first time for the buffet problem. Finally, an extruded three-dimensional geometry of the NACA0012 airfoil, where all velocity components are considered, was also analyzed as a Triglobal stability case, and the outcoming results were compared to the previous 2D limited model, confirming that the buffet onset is well detected.

Efecto sobre el rendimiento productivo y calidad de la canal de la inclusión de guisantes (Pisum sativum) y alberjón (Vicia narbonensis) en el pienso de lechones y cerdos de cebo

Las leguminosas grano presentan un perfil nutricional de gran interés para alimentación de ganado porcino, debido principalmente a su elevado contenido proteico. Sin embargo, la presencia de factores antinutritivos (FAN), que según el género difieren en calidad y cantidad, condiciona la absorción de la proteína, el nutriente más valorado. El objetivo de esta Tesis Doctoral ha sido el estudio del efecto de los principales FAN de guisante y alberjón sobre el rendimiento productivo, de canal y de piezas nobles, cuando sustituyen a la soja, parcial o totalmente, durante la fase estárter y el periodo de engorde de cerdos grasos. Con este motivo se llevaron a cabo 4 ensayos con machos castrados y la misma línea genética: híbrido Duroc x (Landrace x Large white). En el ensayo 1, se estudió la influencia de distintos niveles de inhibidores de proteasas (IP) en el pienso sobre la productividad de lechones durante la fase estárter (40 a 61 días de edad). Para ello, se utilizaron tres variedades de guisantes de invierno que contenían diferentes cantidades de IP, tanto de tripsina (IT) como de quimotripsina (IQ) [unidades de tripsina inhibida/mg (UTI), unidades de quimotripsina inhibida/mg (UQI): 9,87- 10,16, 5,75-8,62 y 12,55-15,75, para guisantes Cartouche, Iceberg y Luna, respectivamente] más elevadas que en la harina de soja 47 (HnaS) y en la soja extrusionada (SE) (UTI/mg - UQI/mg: 0,61-3,56 y 2,36-4,65, para HnaS y SE, respectivamente). El diseño experimental fue al azar, con cuatro tratamientos dietéticos que diferían en las fuentes proteicas y en la cantidad de IP, enfrentando un pienso control de soja a otros tres piensos con guisantes de invierno de las variedades indicadas, que sustituían parcialmente a la soja. Cada tratamiento se replicó cuatro veces, siendo la celda con 6 lechones la unidad experimental. Los animales que consumieron el pienso con guisante Cartouche tuvieron más ganancia media diaria (GMD) que el resto (P < 0,001) con el mismo consumo medio diario (CMD) e índice de conversión (IC). No hubo diferencias significativas entre los animales del pienso control y los que consumieron piensos con guisantes Iceberg y Luna. En el ensayo 2 la leguminosa objeto de estudio fue el alberjón y su FAN el dipéptido _Glutamyl-S-Ethenyl-Cysteine (GEC). El diseño y el periodo experimental fueron los mismos que en el ensayo 1, con cuatro dietas que variaban en el porcentaje de alberjones: 0%, 5%, 15% y 25%, y de GEC (1,54% del grano). Los lechones que consumieron el pienso con 5% tuvieron un CMD y GMD más elevado (P < 0,001), con el mismo IC que los animales pertenecientes al tratamiento 0%. Los índices productivos empeoraron significativamente y de manera progresiva al aumentar el porcentaje de alberjones (15 y 25%). Se obtuvieron ecuaciones de regresión con estructura polinomial que fueron significativas tanto para el nivel de alberjón como para la cantidad de GEC presente en el pienso. El ensayo 3 se efectuó durante el periodo de engorde, sustituyendo por completo la soja a partir de los 84 días de edad con las tres variedades de guisantes de invierno, observando el efecto sobre el rendimiento productivo, de canal y piezas nobles. El diseño, en bloques completos al azar, tuvo cuatro tratamientos según el guisante presente en el pienso y, por lo tanto, los niveles de IP: Control-soja, Cartouche, Iceberg y Luna, con 12 réplicas de 4 cerdos por tratamiento. De 84 a 108 días de edad los animales que consumieron los piensos Control-soja e Iceberg, tuvieron el mismo CMD y GMD, empeorando en los cerdos alimentados con Luna y Cartouche (P < 0,05). El IC fue igual en los tratamientos Control-soja e Iceberg, ocupando una posición intermedia en Cartouche y peor en los cerdos del pienso Luna (P < 0,001). De 109 a 127 días de edad la GMD y el IC fueron iguales, con un CMD más elevado en Control-soja e Iceberg que en los cerdos que consumieron Cartouche y Luna (P < 0,05). No hubo diferencias significativas durante el acabado (128 a 167 días de edad). Globalmente el CMD y GMD fueron más elevados en los cerdos que comieron los piensos Iceberg y Control-soja, empeorando por igual en los que comieron Cartouche y Luna (P < 0,05); el IC fue el mismo en todos los tratamientos. No se observaron diferencias en los datos relacionados con peso y rendimiento de canal y piezas nobles (jamón, paleta y chuletero), ni del contenido de grasa intramuscular en el lomo y proporción de ácidos grasos principales (C16:0, C18:0, C18:1n-9) en la grasa subcutánea. En el ensayo 4, realizado durante el periodo de engorde (60 a 171 días de edad), se valoró el efecto de dietas con distintos niveles de alberjones, y en consecuencia de su factor antinutritivo el dipéptido GEC, sobre el rendimiento productivo y la calidad de la canal y piezas nobles. El diseño fue en cuatro bloques completos al azar, con cuatro tratamientos según el porcentaje de inclusión de alberjón en el pienso: 0%, 5%, 15% y 25%, con 12 réplicas por tratamiento y cuatro cerdos en cada una de ellas. El tratamiento con 5% mejoró la GMD al final de la fase de cebo (152 días de vida) y, junto con el 0%, presentaron los resultados más favorables de peso e IC al final del ensayo (171 días de vida). Del mismo modo, el peso y rendimiento de canal fueron más elevados en los cerdos alimentados con los tratamientos 0% y 5% (P < 0,001). Piensos con el 15 y 25% de alberjones empeoraron los resultados productivos, así como el rendimiento y peso de canal. Sucedió lo mismo con el peso de las piezas nobles (jamón, paleta y chuletero), significativamente superior en 0% y 5% frente a 15% y 25%, siendo los cerdos que consumieron este último pienso los peores. Por el contrario el rendimiento de jamón y chuletero fue más elevado en los cerdos de los tratamientos 25% y 15% que en los que consumieron los piensos con 5% y 0% (P < 0,001); en el rendimiento de paletas se invirtieron los resultados, siendo mayores en los animales de los tratamientos 0% y 5% (P < 0,001). Se obtuvieron ecuaciones de regresión polinomial, para estimar las cantidades de inclusión de alberjones y de GEC más favorables desde el punto de vista productivo, así como los contrastes ortogonales entre los distintos tratamientos. ABSTRACT The grain legumes have a nutritional profile of great interest to feed pigs, mainly due to high protein content. However, the presence of antinutritional factors (ANF), which differ in quality and quantity according to gender, hinder the absorption of the protein, the most valuable nutrient. The aim of this thesis was to study the effect of the main ANF of pea and narbon vetch (NV) on productive performance, of the carcass and main lean cuts, when replacing soybean, partially or totally, during the starter phase and the fattening period of heavy pigs. For this reason were carried four trials with barrows and the same genetic line: Duroc hybrid x (Landrace x Large white). In trial 1, was studied the influence of different levels of protease inhibitors (PI) in the diet over productivity of piglets during the starter phase (40-61 days of age). For this, were used three varieties of winter peas containing different amounts of PI, both trypsin (TI) and chymotrypsin (CI) [inhibited units/mg trypsin (TIU), inhibited units/mg chymotrypsin (CIU): 9.87 - 10.16, 5.75 - 8.62 and 12.55 - 15.75, for peas Cartouche, Iceberg and Luna, respectively] higher than in soybean meal 47 (SBM) and soybeans extruded (SBE) (TIU/mg - CIU/mg: 0.61 - 3.56 and 2.36 - 4.65 for SBM and SBE, respectively). The design was randomized with four dietary treatments differing in protein sources and the amount of PI, with a control diet of soybean and three with different varieties of winter peas: Cartouche, Iceberg and Luna, which partially replace soybean. Each treatment was replicated four times, being the pen with 6 piglets the experimental unit. Pigs that ate the feed with pea Cartouche had better growth (ADG) than the rest (P < 0.001), with the same average daily feed intake (ADFI) and feed conversion ratio (FCR). There were no significant differences between piglets fed with control diet and those fed Iceberg and Luna diets. In trial 2 the legume under study was the NV and your ANF the dipeptide _Glutamyl FAN-S-Ethenyl-Cysteine (GEC). The experimental period and the design were the same as in trial 1, with four diets with different percentage of NV: 0%, 5%, 15% and 25%, and from GEC (1.52% of the grain). The piglets that consumed the feed containing 5% had higher ADG and ADFI (P < 0.05), with the same FCR that pigs belonging to the 0% treatment. Production rates worsened progressively with increasing percentage of NV (15 and 25%). Were obtained regression equations with polynomial structure that were significant for NV percentage and amount of GEC present in the feed. The test 3 was carried out during the fattening period, completely replace soy from 84 days of age with three varieties of winter peas, observing the effect on the yield, carcass and main lean cuts. The design, randomized complete blocks, had four treatments with different levels of PI: Control-soy, Cartouche, Iceberg and Luna, with 12 replicates of 4 pigs per treatment. From 84 to 108 days of age the pigs fed with Control-soy and Iceberg feed, had the same ADFI and ADG, worsening in pigs fed with Luna and Cartouche (P < 0.05). The FCR was similar in diets Control-soy and Iceberg, occupying an intermediate position in Cartouche and worse in pigs fed with Luna (P < 0.001). From 109-127 days of age the ADG and FCR were equal, with higher ADFI in pigs fed with Control-soy and Iceberg, regarding pigs fed with Cartouche and Luna (P < 0.05). There was no difference in the finishing phase (128-167 days of age). In global period, the ADFI and ADG were higher in pigs that ate Control-soy and Iceberg, and worse in those who ate Cartouche and Luna. The FCR was the same in all treatments. No significant differences were observed in the data related to weight and carcass yield, main lean cuts (ham, shoulder and loin chop) and intramuscular fat loin content and major fatty acids proportion (C16:0, C18:0, C18:1n-9) of subcutaneous fat. In experiment 4, made during the fattening period (60-171 days of age), was assessed the effect of diets with different levels of NV, and consequently of GEC, in the performance and quality of carcass and main lean cuts. There was a completely randomized design with four dietary treatments differing in percentage of NV: 0%, 5%, 15% and 25%, with 12 replicates per treatment and four pigs each. Treatment with 5% improved the ADG at the end of the fattening phase (152 days of age) and, together with 0%, showed the most favorable body weight and FCR at the end of the trial (171 days of age). Similarly, the weight and performance of carcass were higher for pigs fed with diets 0% and 5% (P < 0.05). Diets with 15 and 25% worsened the productive and carcass results. The weight of the main lean cuts (ham, shoulder and loin chop) was significantly higher in 0% and 5% vs 15% and 25%.The diet 25% was the worst of all. By contrast the performance of ham and loin chop was higher in pigs fed with diets 25% and 15%, that those who ate diets with 5% and 0% (P < 0.001); the results of shoulder performance were reversed, being greater in pigs feed with diets 0% and 5% (P < 0.001). Polynomial regression equations were obtained to estimate the percentage of NV and GEC more favorable from the point of view of production, and orthogonal contrasts between treatments.

Agricultural use of organic wastes as source of nitrogen and phosphorus: risks and opportunities

El nitrógeno (N) y el fósforo (P) son nutrientes esenciales en la producción de cultivos. El desarrollo de los fertilizantes de síntesis durante el siglo XX permitió una intensificación de la agricultura y un aumento de las producciones pero a su vez el gran input de nutrientes ha resultado en algunos casos en sistemas poco eficientes incrementando las pérdidas de estos nutrientes al medio ambiente. En el caso del P, este problema se agrava debido a la escasez de reservas de roca fosfórica necesaria para la fabricación de fertilizantes fosfatados. La utilización de residuos orgánicos en agricultura como fuente de N y P es una buena opción de manejo que permite valorizar la gran cantidad de residuos que se generan. Sin embargo, es importante conocer los procesos que se producen en el suelo tras la aplicación de los mismos, ya que influyen en la disponibilidad de nutrientes que pueden ser utilizados por el cultivo así como en las pérdidas de nutrientes de los agrosistemas que pueden ocasionar problemas de contaminación. Aunque la dinámica del N en el suelo ha sido más estudiada que la del P, los problemas importantes de contaminación por nitratos en zonas vulnerables hacen necesaria la evaluación de aquellas prácticas de manejo que pudieran agravar esta situación, y en el caso de los residuos orgánicos, la evaluación de la respuesta agronómica y medioambiental de la aplicación de materiales con un alto contenido en N (como los residuos procedentes de la industria vinícola y alcoholera). En cuanto al P, debido a la mayor complejidad de su ciclo y de las reacciones que ocurren en el suelo, hay un mayor desconocimiento de los factores que influyen en su dinámica en los sistemas suelo-planta, lo que supone nuevas oportunidades de estudio en la evaluación del uso agrícola de los residuos orgánicos. Teniendo en cuenta los conocimientos previos sobre cada nutriente así como las necesidades específicas en el estudio de los mismos, en esta Tesis se han evaluado: (1) el efecto de la aplicación de residuos procedentes de la industria vinícola y alcoholera en la dinámica del N desde el punto de vista agronómico y medioambiental en una zona vulnerable a la contaminación por nitratos; y (2) los factores que influyen en la disponibilidad de P en el suelo tras la aplicación de residuos orgánicos. Para ello se han llevado a cabo incubaciones de laboratorio así como ensayos de campo que permitieran evaluar la dinámica de estos nutrientes en condiciones reales. Las incubaciones de suelo en condiciones controladas de humedad y temperatura para determinar el N mineralizado se utilizan habitualmente para estimar la disponibilidad de N para el cultivo así como el riesgo medioambiental. Por ello se llevó a cabo una incubación en laboratorio para conocer la velocidad de mineralización de N de un compost obtenido a partir de residuos de la industria vinícola y alcoholera, ampliamente distribuida en Castilla-La Mancha, región con problemas importantes de contaminación de acuíferos por nitratos. Se probaron tres dosis crecientes de compost correspondientes a 230, 460 y 690 kg de N total por hectárea que se mezclaron con un suelo franco arcillo arenoso de la zona. La evolución del N mineral en el suelo a lo largo del tiempo se ajustó a un modelo de regresión no lineal, obteniendo valores bajos de N potencialmente mineralizable y bajas contantes de mineralización, lo que indica que se trata de un material resistente a la mineralización y con una lenta liberación de N en el suelo, mineralizándose tan solo 1.61, 1.33 y 1.21% del N total aplicado con cada dosis creciente de compost (para un periodo de seis meses). Por otra parte, la mineralización de N tras la aplicación de este material también se evaluó en condiciones de campo, mediante la elaboración de un balance de N durante dos ciclos de cultivo (2011 y 2012) de melón bajo riego por goteo, cultivo y manejo agrícola muy característicos de la zona de estudio. Las constantes de mineralización obtenidas en el laboratorio se ajustaron a las temperaturas reales en campo para predecir el N mineralizado en campo durante el ciclo de cultivo del melón, sin embargo este modelo generalmente sobreestimaba el N mineralizado observado en campo, por la influencia de otros factores no tenidos en cuenta para obtener esta predicción, como el N acumulado en el suelo, el efecto de la planta o las fluctuaciones de temperatura y humedad. Tanto el ajuste de los datos del laboratorio al modelo de mineralización como las predicciones del mismo fueron mejores cuando se consideraba el efecto de la mezcla suelo-compost que cuando se aislaba el N mineralizado del compost, mostrando la importancia del efecto del suelo en la mineralización del N procedente de residuos orgánicos. Dado que esta zona de estudio ha sido declarada vulnerable a la contaminación por nitratos y cuenta con diferentes unidades hidrológicas protegidas, en el mismo ensayo de campo con melón bajo riego por goteo se evaluó el riesgo de contaminación por nitratos tras la aplicación de diferentes dosis de compost bajo dos regímenes de riego, riego ajustado a las necesidades del cultivo (90 ó 100% de la evapotranspiración del cultivo (ETc)) o riego excedentario (120% ETc). A lo largo del ciclo de cultivo se estimó semanalmente el drenaje mediante la realización de un balance hídrico, así como se tomaron muestras de la solución de suelo y se determinó su concentración de nitratos. Para evaluar el riesgo de contaminación de las aguas subterráneas asociado con estas prácticas, se utilizaron algunos índices medioambientales para determinar la variación en la calidad del agua potable (Índice de Impacto (II)) y en la concentración de nitratos del acuífero (Índice de Impacto Ambiental (EII)). Para combinar parámetros medioambientales con parámetros de producción, se calculó la eficiencia de manejo. Se observó que la aplicación de compost bajo un régimen de riego ajustado no aumentaba el riesgo de contaminación de las aguas subterráneas incluso con la aplicación de la dosis más alta. Sin embargo, la aplicación de grandes cantidades de compost combinada con un riego excedentario supuso un incremento en el N lixiviado a lo largo del ciclo de cultivo, mientras que no se obtuvieron mayores producciones con respecto al riego ajustado. La aplicación de residuos de la industria vinícola y alcoholera como fuente de P fue evaluada en suelos calizos caracterizados por una alta capacidad de retención de P, lo cual en algunos casos limita la disponibilidad de este nutriente. Para ello se llevó a cabo otro ensayo de incubación con dos suelos de diferente textura, con diferente contenido de carbonato cálcico, hierro y con dos niveles de P disponible; a los que se aplicaron diferentes materiales procedentes de estas industrias (con y sin compostaje previo) aportando diferentes cantidades de P. A lo largo del tiempo se analizó el P disponible del suelo (P Olsen) así como el pH y el carbono orgánico disuelto. Al final de la incubación, con el fin de estudiar los cambios producidos por los diferentes residuos en el estado del P del suelo se llevó a cabo un fraccionamiento del P inorgánico del suelo, el cual se separó en P soluble y débilmente enlazado (NaOH-NaCl-P), P soluble en reductores u ocluido en los óxidos de Fe (CBD-P) y P poco soluble precipitado como Ca-P (HCl-P); y se determinó la capacidad de retención de P así como el grado de saturación de este elemento en el suelo. En este ensayo se observó que, dada la naturaleza caliza de los suelos, la influencia de la cantidad de P aplicado con los residuos en el P disponible sólo se producía al comienzo del periodo de incubación, mientras que al final del ensayo el incremento en el P disponible del suelo se igualaba independientemente del P aplicado con cada residuo, aumentando el P retenido en la fracción menos soluble con el aumento del P aplicado. Por el contrario, la aplicación de materiales orgánicos menos estabilizados y con un menor contenido en P, produjo un aumento en las formas de P más lábiles debido a una disolución del P retenido en la fracción menos lábil, lo cual demostró la influencia de la materia orgánica en los procesos que controlan el P disponible en el suelo. La aplicación de residuos aumentó el grado de saturación de P de los suelos, sin embargo los valores obtenidos no superaron los límites establecidos que indican un riesgo de contaminación de las aguas. La influencia de la aplicación de residuos orgánicos en las formas de P inorgánico y orgánico del suelo se estudió además en un suelo ácido de textura areno francosa tras la aplicación en campo a largo plazo de estiércol vacuno y de compost obtenido a partir de biorresiduos, así como la aplicación combinada de compost y un fertilizante mineral (superfosfato tripe), en una rotación de cultivos. En muestras de suelo recogidas 14 años después del establecimiento del experimento en campo, se determinó el P soluble y disponible, la capacidad de adsorción de P, el grado de saturación de P así como diferentes actividades enzimáticas (actividad deshidrogenasa, fosfatasa ácida y fosfatasa alcalina). Las diferentes formas de P orgánico en el suelo se estudiaron mediante una técnica de adición de enzimas con diferentes substratos específicos a extractos de suelo de NaOH-EDTA, midiendo el P hidrolizado durante un periodo de incubación por colorimetría. Las enzimas utilizadas fueron la fosfatasa ácida, la nucleasa y la fitasa las cuales permitieron identificar monoésteres hidrolizables (monoester-like P), diésteres (DNA-like P) e inositol hexaquifosfato (Ins6P-like P). La aplicación a largo plazo de residuos orgánicos aumentó el P disponible del suelo proporcionalmente al P aplicado con cada tipo de fertilización, suponiendo un mayor riesgo de pérdidas de P dado el alto grado de saturación de este suelo. La aplicación de residuos orgánicos aumentó el P orgánico del suelo resistente a la hidrólisis enzimática, sin embargo no influyó en las diferentes formas de P hidrolizable por las enzimas en comparación con las observadas en el suelo sin enmendar. Además, las diferentes formas de P orgánico aplicadas con los residuos orgánicos no se correspondieron con las analizadas en el suelo lo cual demostró que éstas son el resultado de diferentes procesos en el suelo mediados por las plantas, los microorganismos u otros procesos abióticos. En este estudio se encontró una correlación entre el Ins6P-like P y la actividad microbiana (actividad deshidrogenasa) del suelo, lo cual refuerza esta afirmación. Por último, la aplicación de residuos orgánicos como fuente de N y P en la agricultura se evaluó agronómicamente en un escenario real. Se estableció un experimento de campo para evaluar el compost procedente de residuos de bodegas y alcoholeras en el mismo cultivo de melón utilizado en el estudio de la mineralización y lixiviación de N. En este experimento se estudió la aplicación de tres dosis de compost: 1, 2 y 3 kg de compost por metro lineal de plantación correspondientes a 7, 13 y 20 t de compost por hectárea respectivamente; y se estudió el efecto sobre el crecimiento de las plantas, la acumulación de N y P en la planta, así como la producción y calidad del cultivo. La aplicación del compost produjo un ligero incremento en la biomasa vegetal acompañado por una mejora significativa de la producción con respecto a las parcelas no enmendadas, obteniéndose la máxima producción con la aplicación de 2 kg de compost por metro lineal. Aunque los efectos potenciales del N y P fueron parcialmente enmascarados por otras entradas de estos nutrientes en el sistema (alta concentración de nitratos en el agua de riego y ácido fosfórico suministrado por fertirrigación), se observó una mayor acumulación de P uno de los años de estudio que resultó en un aumento en el número de frutos en las parcelas enmendadas. Además, la mayor acumulación de N y P disponible en el suelo al final del ciclo de cultivo indicó el potencial uso de estos materiales como fuente de estos nutrientes. ABSTRACT Nitrogen (N) and phosphorus (P) are essential nutrients in crop production. The development of synthetic fertilizers during the 20th century allowed an intensification of the agriculture increasing crop yields but in turn the great input of nutrients has resulted in some cases in inefficient systems with higher losses to the environment. Regarding P, the scarcity of phosphate rock reserves necessary for the production of phosphate fertilizers aggravates this problem. The use of organic wastes in agriculture as a source of N and P is a good option of management that allows to value the large amount of wastes generated. However, it is important to understand the processes occurring in the soil after application of these materials, as they affect the availability of nutrients that can be used by the crop and the nutrient losses from agricultural systems that can cause problems of contamination. Although soil N dynamic has been more studied than P, the important concern of nitrate pollution in Nitrate Vulnerable Zones requires the evaluation of those management practices that could aggravate this situation, and in the case of organic wastes, the evaluation of the agronomic and environmental response after application of materials with a high N content (such as wastes from winery and distillery industries). On the other hand, due to the complexity of soil P cycle and the reactions that occur in soil, there is less knowledge about the factors that can influence its dynamics in the soil-plant system, which means new opportunities of study regarding the evaluation of the agricultural use of organic wastes. Taking into account the previous knowledge of each nutrient and the specific needs of study, in this Thesis we have evaluated: (1) the effect of the application of wastes from the winery and distillery industries on N dynamics from the agronomic and environmental viewpoint in a vulnerable zone; and (2) the factors that influence P availability in soils after the application of organic wastes. With this purposes, incubations were carried out in laboratory conditions as well as field trials that allow to assess the dynamic of these nutrients in real conditions. Soil incubations under controlled moisture and temperature conditions to determine N mineralization are commonly used to estimate N availability for crops together with the environmental risk. Therefore, a laboratory incubation was conducted in order to determine the N mineralization rate of a compost made from wastes generated in the winery and distillery industries, widely distributed in Castilla-La Mancha, a region with significant problems of aquifers contamination by nitrates. Three increasing doses of compost corresponding to 230, 460 and 690 kg of total N per hectare were mixed with a sandy clay loam soil collected in this area. The evolution of mineral N in soil over time was adjusted to a nonlinear regression model, obtaining low values of potentially mineralizable N and low constants of mineralization, indicating that it is a material resistant to mineralization with a slow release of N, with only 1.61, 1.33 and 1.21% of total N applied being mineralized with each increasing dose of compost (for a period of six months). Furthermore, N mineralization after the application of this material was also evaluated in field conditions by carrying out a N balance during two growing seasons (2011 and 2012) of a melon crop under drip irrigation, a crop and management very characteristic of the area of study. The mineralization constants obtained in the laboratory were adjusted to the actual temperatures observed in the field to predict N mineralized during each growing season, however, this model generally overestimated the N mineralization observed in the field, because of the influence of other factors not taken into account for this prediction, as N accumulated in soil, the plant effect or the fluctuations of temperature and moisture. The fitting of the laboratory data to the model as well as the predictions of N mineralized in the field were better when considering N mineralized from the soil-compost mixture rather than when N mineralized from compost was isolated, underlining the important role of the soil on N mineralization from organic wastes. Since the area of study was declared vulnerable to nitrate pollution and is situated between different protected hydrological units, the risk of nitrate pollution after application of different doses compost was evaluated in the same field trial with melon under two irrigation regimes, irrigation adjusted to the crop needs (90 or 100% of the crop evapotranspiration (ETc)) or excedentary irrigation (120% ETc). Drainage was estimated weekly throughout the growing season by conducting a water balance, samples of the soil solution were taken and the concentration of nitrates was determined. To assess the risk of groundwater contamination associated with these practices, some environmental indices were used to determine the variation in the quality of drinking water (Impact Index (II)) and the nitrates concentration in the groundwater (Environmental Impact Index (EII)). To combine environmental parameters together with yield parameters, the Management Efficiency was calculated. It was observed that the application of compost under irrigation adjusted to the plant needs did not represent a higher risk of groundwater contamination even with the application of the highest doses. However, the application of large amounts of compost combined with an irrigation surplus represented an increase of N leaching during the growing season compared with the unamended plots, while no additional yield with respect to the adjusted irrigation strategy is obtained. The application of wastes derived from the winery and distillery industry as source of P was evaluated in calcareous soils characterized by a high P retention capacity, which in some cases limits the availability of this nutrient. Another incubation experiment was carried out using two soils with different texture, different calcium carbonate and iron contents and two levels of available P; to which different materials from these industries (with and without composting) were applied providing different amounts of P. Soil available P (Olsen P), pH and dissolved organic carbon were analyzed along time. At the end of the incubation, in order to study the changes in soil P status caused by the different residues, a fractionation of soil inorganic P was carried out, which was separated into soluble and weakly bound P (NaOH-NaCl- P), reductant soluble P or occluded in Fe oxides (CBD-P) and P precipitated as poorly soluble Ca-P (HCl-P); and the P retention capacity and degree of P saturation were determined as well. Given the calcareous nature of the soils, the influence of the amount of P applied with the organic wastes in soil available P only occurred at the beginning of the incubation period, while at the end of the trial the increase in soil available P equalled independently of the amount of P applied with each residue, increasing the P retained in the least soluble fraction when increasing P applied. Conversely, the application of less stabilized materials with a lower content of P resulted in an increase in the most labile P forms due to dissolution of P retained in the less labile fraction, demonstrating the influence of organic matter addition on soil P processes that control P availability in soil. As expected, the application of organic wastes increased the degree of P saturation in the soils, however the values obtained did not exceed the limits considered to pose a risk of water pollution. The influence of the application of organic wastes on inorganic and organic soil P forms was also studied in an acid loamy sand soil after long-term field application of cattle manure and biowaste compost and the combined application of compost and mineral fertilizer (triple superphosphate) in a crop rotation. Soil samples were collected 14 years after the establishment of the field experiment, and analyzed for soluble and available P, P sorption capacity, degree of P saturation and enzymatic activities (dehydrogenase, acid phosphatase and alkaline phosphatase). The different forms of organic P in soil were determined by using an enzyme addition technique, based on adding enzymes with different substrate specificities to NaOH-EDTA soil extracts, measuring the hydrolyzed P colorimetrically after an incubation period. The enzymes used were acid phosphatase, nuclease and phytase which allowed to identify hydrolyzable monoesters (monoester-like P) diesters (DNA-like P) and inositol hexakisphosphate (Ins6P-like P). The long-term application of organic wastes increased soil available P proportionally to the P applied with each type of fertilizer, assuming a higher risk of P losses given the high degree of P saturation of this soil. The application of organic wastes increased soil organic P resistant to enzymatic hydrolysis, but no influence was observed regarding the different forms of enzyme hydrolyzable organic P compared to those observed in the non-amended soil. Furthermore, the different forms of organic P applied with the organic wastes did not correspond to those analyzed in the soil which showed that these forms in soil are a result of multifaceted P turnover processes in soil affected by plants, microorganisms and abiotic factors. In this study, a correlation between Ins6P-like P and the microbial activity (dehydrogenase activity) of soil was found, which reinforces this claim. Finally, the application of organic wastes as a source of N and P in agriculture was evaluated agronomically in a real field scenario. A field experiment was established to evaluate the application of compost made from wine-distillery wastes in the same melon crop used in the experiments of N mineralization and leaching. In this experiment the application of three doses of compost were studied: 1 , 2 and 3 kg of compost per linear meter of plantation corresponding to 7, 13 and 20 tonnes of compost per hectare respectively; and the effect on plant growth, N and P accumulation in the plant as well as crop yield and quality was studied. The application of compost produced a slight increase in plant biomass accompanied by a significant improvement in crop yield with respect to the unamended plots, obtaining the maximum yield with the application of 2 kg of compost per linear meter. Although the potential effects of N and P were partially masked by other inputs of these nutrients in the system (high concentration of nitrates in the irrigation water and phosphoric acid supplied by fertigation), an effect of P was observed the first year of study resulting in a greater plant P accumulation and in an increase in the number of fruits in the amended plots. In addition, the higher accumulation of available N and P in the topsoil at the end of the growing season indicated the potential use of this material as source of these nutrients.

Aplicación integral en construcción de materiales eco-eficientes con incorporación de cenizas de biomasa

El empleo de biomasa como combustible para la generación de bio-energía va en aumento en la actualidad, debido a su impacto medioambiental nulo en cuanto a las emisiones de CO2. Por lo tanto la generación de cenizas de biomasa, residuo de la producción de esta energía, constituye un problema medioambiental con un claro impacto social y económico. Este tipo de ceniza tiene contenidos en óxidos que la hacen atractiva para su empleo como sustituto parcial del cemento Portland, lo cual proporciona una salida eco-eficiente a este residuo, reduciendo al mismo tiempo la emisión de gases de efecto invernadero asociada a la fabricación del cemento. Esta investigación se centra en el desarrollo de nuevos e innovadores materiales base-cemento eco-eficientes que incorporan ceniza de biomasa para su aplicación integral en construcción. Para ello, se emplea una ceniza de biomasa (CB) procedente de un combustor de lecho fluidizado, cuya biomasa de combustión es principalmente restos de corteza de eucalipto, suministrada por el grupo ENCE-Navia (Asturias). El trabajo desarrollado en la presente tesis doctoral, tiene como primera fase la caracterización de esta ceniza y el análisis de viabilidad de su valorización en materiales base-cemento. Dentro de este análisis, se propone la activación de la ceniza CB mediante tratamiento hidrotermal (TH) en diferentes condiciones de medio activante, temperatura y tiempo de proceso, con el objetivo de favorecer la formación de fases hidratadas que potencien la valorización de la ceniza en el campo de los materiales de construcción. Como fase hidratada de interés se obtiene la fase tobermorita (Ca2.25(Si3O7.5(OH)1.5)(H2O)), precursora del gel C-S-H, responsable del desarrollo de resistencias mecánicas en los materiales base-cemento. El proceso de TH se optimiza para la síntesis más eficiente de esta fase. El estudio posterior de las propiedades mecánicas y micro-estructurales de pastas de cemento eco-eficientes que incorporan la ceniza CB y la ceniza tratada hidrotermalmente, CB-TH, confirma una mayor viabilidad de incorporación de la ceniza CB como sustituto parcial del cemento Portland. Como siguiente paso en el desarrollo de estos innovadores materiales base-cemento eco-eficientes se amplía el estudio multi-escalar de los materiales que incorporan CB mediante diferentes ensayos físico-mecánicos y de durabilidad. Los resultados indican que la presencia de la ceniza de biomasa no tiene efectos negativos sobre las propiedades físicas de los morteros eco-eficientes estudiados. Sin embargo, la adición de CB proporciona una mejor durabilidad del material al producir modificaciones de la microestructura que dificultan el transporte de agentes agresivos. Por otro lado, los morteros con un 10 y 20% de sustitución parcial de cemento por la ceniza de biomasa CB (CB-10 y CB-20) presentan una resistencia a compresión de 53.3 y 50.5 MPa a 28 días de curado, respectivamente. Estos morteros son comparables con un cemento Portland tradicional tipo CEM I de clase de resistencia 42.5 R. Por último, y con el fin de proporcionar la apertura de estos nuevos cementos eco-eficientes al mercado en el campo de los materiales de construcción, se estudian propiedades concretas relacionadas con diferentes tipos de aplicaciones. Concretamente se estudian en detalle las propiedades relativas a la aplicación en baldosas de mortero y los resultados indican unas prestaciones del material eco-eficiente con incorporación de CB similares o mejoradas con respecto al cemento Portland. Se analiza también la viabilidad de aplicación estructural de los cementos eco-eficientes desarrollados mediante el estudio de la adherencia al acero, que resulta similar a la del material de referencia. En cuanto a los resultados de extracción y caracterización de la fase acuosa de los poros, en todas las matrices eco-eficientes se obtiene un pH que garantiza la pasivación de la armadura. Sin embargo, el alto contenido en cloruros de dicha fase acuosa sugiere la conveniencia de realizar un análisis más detallado para la aplicación de los nuevos materiales eco-eficientes en hormigón armado. Se comprueba que todas las matrices que incorporan CB en porcentajes entre un 10 y un 90%, se pueden considerar adecuadas como nuevos materiales de construcción más eco-eficientes en aplicaciones con distintos niveles de exigencias mecánicas y sin problemas ambientales asociados con procesos de lixiviación. Con el presente trabajo de investigación se completan los objetivos iniciales de la tesis, con la obtención de nuevos e innovadores materiales base-cemento eco-eficientes que incorporan cenizas de biomasa (CB) con aplicación integral en el campo de la construcción. ABSTRACT The use of biomass as a fuel for the generation of bio-energy is increasing nowadays, due to its zero environmental impact in terms of CO2 emissions. Therefore the generation of biomass ash, a by-product of this energy, is an environmental problem with a clear social and economic impact. This type of ash contains oxides that make it attractive to be used as a partial replacement of Portland cement, providing an eco-efficient solution to this residue, while reducing the emission of greenhouse gases associated with the production of cement. The present research is focused on the development of new and innovative eco-efficient cement-based materials that incorporate biomass ash for their comprehensive application in construction. For this purpose a biomass ash (CB) is used from a fluidized bed forest combustor mainly fed with the bark of eucalyptus trees, provided by the ENCE-Navia (Asturias) group. The work includes in the first stage the characterization of the raw materials and the analysis of viability of their valorization in cement-based materials. Within this analysis, the activation of the ash is proposed by hydrothermal treatment (HT) in different conditions of activation medium, temperature and process duration, aiming an enhanced formation of hydrated phases to improve the ash valorization in the construction materials field. As an interesting hydrated phase, the tobermorite (Ca2.25(Si3O7.5(OH)1.5)(H2O)) is obtained from the process. This phase is considered as a precursor of the gel C-S-H, responsible for the development of mechanical strength in cement-based materials. HT process is optimized for the most efficient synthesis of tobermorite. The analysis of mechanical and microstructural properties of eco-efficient cement pastes incorporating CB ash and hydrothermally treated ash, CB-TH, confirms an improved viability of incorporation of CB ash as a partial replacement for Portland cement in the case. As a next step in the development of these innovative eco-efficient cement-based materials, a multiscale study of the materials that incorporate CB by different physical-mechanical and durability tests is carried out. The results indicate that the presence of biomass ash does not give rise to negative effects on the physical properties of the eco-efficient mortars analyzed. Nevertheless, the addition of CB produces a better durability performance due to microstructural modifications that hinder the transport of aggressive agents through the material. Moreover, mortars with a 10% and 20% of partial substitution of cement by the CB biomass ash (CB-10 and CB-20) show a compressive resistance of 53.3 and 50.5 MPa at 28 days of curing, respectively. These mortars are comparable to an ordinary Portland cement type CEM I with a resistance class of 42.5R. Finally, and in order to provide the opening of these new eco-efficient cement to the market in the field of construction materials, certain properties specifically related to different types of applications are studied. Among these, the properties concerning the application in mortar tiles are analyzed and the results indicate a similar, or even better performance of the eco-efficient mortar that incorporates CB, with respect to Portland cement. The viability of structural application of the developed eco-efficient cement is also performed considering the study of the adhesion to steel, with results similar to those of the reference material. Regarding the results of extraction and analysis of the aqueous phase of the pores, a pH value guaranteeing reinforcement passivation is obtained for all the eco-efficient matrices. However, high chloride content is obtained suggesting the suitability of a more detailed study to evaluate the application of these new eco-efficient materials in reinforced concrete. It is established that all the matrices incorporating CB in percentages between 10 and 90% may be considered adequate as new more eco-efficient construction materials in applications with different levels of mechanical demand and without environmental problems associated to leaching processes. In this research the initial objectives of the thesis are fulfilled by obtaining new and innovative eco-efficient cement-based materials that incorporate biomass ashes (CB) with comprehensive application in the construction field.

Stranski-Krastanov InN/InGaN quantum dots grown directly on Si(111)

The authors discuss and demonstrate the growth of InN surface quantum dots on a high-In-content In0.73Ga0.27N layer, directly on a Si(111) substrate by plasma-assisted molecular beam epitaxy. Atomic force microscopy and transmission electron microscopy reveal uniformly distributed quantum dots with diameters of 10–40 nm, heights of 2–4 nm, and a relatively low density of ∼7 × 109 cm−2. A thin InN wetting layer below the quantum dots proves the Stranski-Krastanov growth mode. Near-field scanning optical microscopy shows distinct and spatially well localized near-infrared emission from single surface quantum dots. This holds promise for future telecommunication and sensing devices.

Arsenic speciation in edible alga samples by microwave-assisted extraction and high performance liquid chromatography coupled to atomic fluorescence spectrometry

Twelve commercially available edible marine algae from France, Japan and Spain and the certified reference material (CRM) NIES No. 9 Sargassum fulvellum were analyzed for total arsenic and arsenic species. Total arsenic concentrations were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) after microwave digestion and ranged from 23 to 126 μg g−1. Arsenic species in alga samples were extracted with deionized water by microwave-assisted extraction and showed extraction efficiencies from 49 to 98%, in terms of total arsenic. The presence of eleven arsenic species was studied by high performance liquid chromatography–ultraviolet photo-oxidation–hydride generation atomic–fluorescence spectrometry (HPLC–(UV)–HG–AFS) developed methods, using both anion and cation exchange chromatography. Glycerol and phosphate sugars were found in all alga samples analyzed, at concentrations between 0.11 and 22 μg g−1, whereas sulfonate and sulfate sugars were only detected in three of them (0.6-7.2 μg g−1). Regarding arsenic toxic species, low concentration levels of dimethylarsinic acid (DMA) (<0.9 μg g−1) and generally high arsenate (As(V)) concentrations (up to 77 μg g−1) were found in most of the algae studied. The results obtained are of interest to highlight the need to perform speciation analysis and to introduce appropriate legislation to limit toxic arsenic species content in these food products.

Influence of cement properties in the reaction rate and mechanical behavior of concrete with high fl y ash content

The use of fly ash (FA) as an admixture to concrete is broadly extended for two main reasons: the reduction of costs that supposes the substitution of cement and the micro structural changes motivated by the mineral admixture. Regarding this second point, there is a consensus that considers that the ash generates a more compact concrete and a reduction in the size of the pore. However, the measure in which this contributes to the pozzolanic activity or as filler is not well defined. There is also no justification to the influence of the physical parameters, fineness of the grain and free water, in its behavior. This work studies the use of FA as a partial substitute of the cement in concretes of different workability (dry and wet) and the influence in the reactivity of the ash. The concrete of dry consistency which serves as reference uses a cement dose of 250 Kg/m 3 and the concrete of fluid consistency utilized a dose of cement of 350 Kg/m 3 . Two trademark of Portland Cement Type 1 were used. The first reached the resistant class for its fineness of grain and the second one for its composition. Moreover, three doses of FA have been used, and the water/binder ratio was constant in all the mixtures. We have studied the mechanical properties and the micro-structure of the concretes by means of compressive strength tests, mercury intrusion porosimetry (MIP) and thermal analysis (TA). The results of compressive strength tests allow us to observe that concrete mixtures with cements of the same classification and similar dosage of binder do not present the same mechanical behavior. These results show that the effective water/binder ratio has a major role in the development of the mechanical properties of concrete. The study of different dosages using TA, thermo-gravimetry and differential thermal analysis, revealed that the portlandite content is not restrictive in any of the dosages studied. Again, this proves that the rheology of the material influences the reaction rate and content of hydrated cement products. We conclude that the available free water is determinant in the efficiency of pozzolanic reaction. It is so that in accordance to the availability of free water, the ashes can react as an active admixture or simply change the porous distribution. The MIP shows concretes that do not exhibit significant changes in their mechanical behavior, but have suffered significant variation in their porous structure

Methodologies for an improved prediction of the isotopic content in high burnup samples. Application to Vandellos-II reactor core

Fuel cycles are designed with the aim of obtaining the highest amount of energy possible. Since higher burnup values are reached, it is necessary to improve our disposal designs, traditionally based on the conservative assumption that they contain fresh fuel. The criticality calculations involved must consider burnup by making the most of the experimental and computational capabilities developed, respectively, to measure and predict the isotopic content of the spent nuclear fuel. These high burnup scenarios encourage a review of the computational tools to find out possible weaknesses in the nuclear data libraries, in the methodologies applied and their applicability range. Experimental measurements of the spent nuclear fuel provide the perfect framework to benchmark the most well-known and established codes, both in the industry and academic research activity. For the present paper, SCALE 6.0/TRITON and MONTEBURNS 2.0 have been chosen to follow the isotopic content of four samples irradiated in the Spanish Vandellós-II pressurized water reactor up to burnup values ranging from 40 GWd/MTU to 75 GWd/MTU. By comparison with the experimental data reported for these samples, we can probe the applicability of these codes to deal with high burnup problems. We have developed new computational tools within MONTENBURNS 2.0. They make possible to handle an irradiation history that includes geometrical and positional changes of the samples within the reactor core. This paper describes the irradiation scenario against which the mentioned codes and our capabilities are to be benchmarked.