Impact of N2 plasma power and duration on AlGaN/GaN HEMT

urface treatments have been recently shown to play an active role in electrical characteristics in AlGaN/GaN HEMTs, in particular during the passivation processing [1-4]. However, the responsible mechanisms are partially unknown and further studies are demanding. The effects of power and time N2 plasma pre-treatment prior to SiN deposition using PE-CVD (plasma enhanced chemical vapour deposition) on GaN and AlGaN/GaN HEMT have been investigated. The low power (60 W) plasma pre-treatment was found to improve the electronic characteristics in GaN based HEMT devices, independently of the time duration up to 20 min. In contrast, high power (150 and 210 W) plasma pretreatment showed detrimental effects in the electronic properties (Fig. 1), increasing the sheet resistance of the 2DEG, decreasing the 2DEG charge density in AlGaN/GaN HEMTs, transconductance reduction and decreasing the fT and fmax values up to 40% respect to the case using 60 W N2 plasma power. Although AFM (atomic force microscopy) results showed AlGaN and GaN surface roughness is not strongly affected by the N2-plasma, KFM (Kelvin force microscopy) surface analysis shows significant changes in the surface potential, trending to increase its values as the plasma power is higher. The whole results point at energetic ions inducing polarization-charge changes that affect dramatically to the 2-DEG charge density and the final characteristics of the HEMT devices. Therefore, we conclude that AlGaN surface is strongly sensitive to N2 plasma power conditions, which turn to be a key factor to achieve a good surface preparation prior to SiN passivation.

Use of calculus of variations to determine the shape of hovering rotors of minimum power and its application to micro air vehicles

In this paper, calculus of variations and combined blade element and momentum theory (BEMT) are used to demonstrate that, in hover, when neither root nor tip losses are considered; the rotor, which minimizes the total power (MPR), generates an induced velocity that varies linearly along the blade span. The angle of attack of every blade element is constant and equal to its optimum value. The traditional ideal twist (ITR) and optimum (OR) rotors are revisited in the context of this variational framework. Two more optimum rotors are obtained considering root and tip losses, the ORL, and the MPRL. A comparison between these five rotors is presented and discussed. The MPR and MPRL present a remarkable saving of power for low values of both thrust coefficient and maximum aerodynamic efficiency. The result obtained can be exploited to improve the aerodynamic behaviour of rotary wing micro air vehicles (MAV). A comparison with experimental results obtained from the literature is presented.

The effects of storage duration, temperature and cultivar on the severity of garlic clove rot caused by Fusarium proliferatum.

Diseases that affect garlic during storage can lead to severe economic losses for farmers worldwide. One causal agent of clove rot is Fusarium proliferatum. Here, the progress of clove rot caused by F. proliferatum and its dependence on different storage conditions and cultivar type were studied. The effect of temperature on mycelial growth, conidial viability, and fungal survival during garlic commercial storage was documented. Samples of 50 bulbs from a randomized field trial with three different clonal generations for purple garlic (F3, F4 and F5) and the F4 clonal generation for white garlic were labeled and stored for two months (short-term storage). In addition, another sample of the F5 clonal generation of purple garlic was stored for 6 months after harvest (long-term storage). The presence of the pathogen and the percentage of symptomatic cloves were evaluated. A notable difference in the rot severity index (RSI) of different garlic varieties was observed. In all studied cases, clove rot increased with storage time at 20 ◦ C, and the white garlic variety had a higher index of rot severity after two months of storage. Additionally, there were clear differences between the growth rates of F. proliferatum isolates. Studies conducted on the temperature responses of the pathogen propagules showed that expo- sure for at least 20 min at 50 ◦ C was highly effective in significantly reducing the viability of fungal conidia. Pathogenicity studies showed that the fungus is pathogenic in all commercial varieties. However, there were significant differences in varietal susceptibility between Chinese and white garlic type cultivars (81.84 ± 16.44% and 87.5 ± 23.19% symptomatic cloves, respectively) and purple cultivars (49.06 ± 13.42% symptomatic cloves)

Calculus of the uncertainty in acoustic field measurements: comparative study between the uncertainty propagation method and the distribution propagation method

The new Spanish Regulation in Building Acoustic establishes values and limits for the different acoustic magnitudes whose fulfillment can be verify by means field measurements. In this sense, an essential aspect of a field measurement is to give the measured magnitude and the uncertainty associated to such a magnitude. In the calculus of the uncertainty it is very usual to follow the uncertainty propagation method as described in the Guide to the expression of Uncertainty in Measurements (GUM). Other option is the numerical calculus based on the distribution propagation method by means of Monte Carlo simulation. In fact, at this stage, it is possible to find several publications developing this last method by using different software programs. In the present work, we used Excel for the Monte Carlo simulation for the calculus of the uncertainty associated to the different magnitudes derived from the field measurements following ISO 140-4, 140-5 and 140-7. We compare the results with the ones obtained by the uncertainty propagation method. Although both methods give similar values, some small differences have been observed. Some arguments to explain such differences are the asymmetry of the probability distributions associated to the entry magnitudes,the overestimation of the uncertainty following the GUM

Integración del descodificador OpenSVC en el DSP del OMAP3530

Hoy en día el uso de dispositivos portátiles multimedia es ya una realidad totalmente habitual. Además, estos dispositivos tienen una capacidad de cálculo y unos recursos gráficos y de memoria altos, tanto es así que por ejemplo en un móvil se pueden reproducir vídeos de muy alta calidad o tener capacidad para manejar entornos 3D. El precio del uso de estos recursos es un mayor consumo de batería que en ocasiones es demasiado alto y acortan en gran medida la vida de la carga útil de la batería. El Grupo de Diseño Electrónico y Microelectrónico de la Universidad Politécnica de Madrid ha abierto una línea de trabajo que busca la optimización del consumo de energía en este tipo de dispositivos, concretamente en el ámbito de la reproducción de vídeo. El enfoque para afrontar la solución del problema se basa en obtener un mayor rendimiento de la batería a costa de disminuir la experiencia multimedia del usuario. De esta manera, cuando la carga de la batería esté por debajo de un determinado umbral mientras el dispositivo esté reproduciendo un vídeo de alta calidad será el dispositivo quien se autoconfigure dinámicamente para consumir menos potencia en esta tarea, reduciendo la tasa de imágenes por segundo o la resolución del vídeo que se descodifica. Además de lo citado anteriormente se propone dividir la descodificación y la representación del vídeo en dos procesadores, uno de propósito general y otro para procesado digital de señal, con esto se consigue que tener la misma capacidad de cálculo que con un solo procesador pero a una frecuencia menor. Para materializar la propuesta se usará la tarjeta BeagleBoard basada en un procesador multinúcleo OMAP3530 de Texas Instrument que contiene dos núcleos: un ARM1 Cortex-A8 y un DSP2 de la familia C6000. Este procesador multinúcleo además permite modificar la frecuencia de reloj y la tensión de alimentación dinámicamente para conseguir reducir de este modo el consumo del terminal. Por otro lado, como reproductor de vídeos se utilizará una versión de MPlayer que integra un descodificador de vídeo escalable que permite elegir dinámicamente la resolución o las imágenes por segundo que se decodifican para posteriormente mostrarlas. Este reproductor se ejecutará en el núcleo ARM pero debido a la alta carga computacional de la descodificación de vídeos, y que el ARM no está optimizado para este tipo de procesado de datos, el reproductor debe encargar la tarea de la descodificación al DSP. El objetivo de este Proyecto Fin de Carrera consiste en que mientras el descodificador de vídeo está ejecutándose en el núcleo DSP y el Mplayer en el núcleo ARM del OMAP3530 se pueda elegir dinámicamente qué parte del vídeo se descodifica, es decir, seleccionar en tiempo real la calidad o capa del vídeo que se quiere mostrar. Haciendo esto, se podrá quitar carga computacional al núcleo ARM y asignársela al DSP el cuál puede procesarla a menor frecuencia para ahorrar batería. 1 ARM: Es una arquitectura de procesadores de propósito general basada en RISC (Reduced Instruction Set Computer). Es desarrollada por la empresa inglesa ARM holdings. 2 DSP: Procesador Digital de Señal (Digital Signal Processor). Es un sistema basado en procesador, el cual está orientado al cálculo matemático a altas velocidad. Generalmente poseen varias unidades aritmético-lógicas (ALUs) para conseguir realizar varias operaciones simultáneamente. SUMMARY. Nowadays, the use of multimedia devices is a well known reality. In addition, these devices have high graphics and calculus performance and a lot of memory as well. In instance, we can play high quality videos and 3D environments in a mobile phone. That kind of use may increase the device's power consumption and make shorter the battery duration. Electronic and Microelectronic Design Group of Technical University of Madrid has a research line which is looking for optimization of power consumption while these devices are playing videos. The solution of this trouble is based on taking more advantage of battery by decreasing multimedia user experience. On this way, when battery charge is under a threshold while device is playing a high quality video the device is going to configure itself dynamically in order to decrease its power consumption by decreasing frame per second rate, video resolution or increasing the noise in the decoded frame. It is proposed splitting decoding and representation tasks in two processors in order to have the same calculus capability with lower frecuency. The first one is specialized in digital signal processing and the other one is a general purpose processor. In order to materialize this proposal we will use a board called BeagleBoard which is based on a multicore processor called OMAP3530 from Texas Instrument. This processor includes two cores: ARM Cortex-A8 and a TMS320C64+ DSP core. Changing clock frequency and supply voltage is allowed by OMAP3530, we can decrease the power consumption on this way. On the other hand, MPlayer will be used as video player. It includes a scalable video decoder which let us changing dynamically the resolution or frames per second rate of the video in order to show it later. This player will be executed by ARM core but this is not optimized for this task, for that reason, DSP core will be used to decoding video. The target of this final career project is being able to choose which part of the video is decoded each moment while decoder is executed by DSP and Mplayer by ARM. It will be able to change in real time the video quality, resolution and frames per second that user want to show. On this way, reducing the computational charge within the processor will be possible.

Influence of crude protein content, ingredient complexity, feed form, and duration of feeding of the phase I diets on productive performance and nutrient digestibility of Iberian pigs.

The influence of CP content and ingredient complexity, feed form, and duration of feeding of the Phase I diets on growth performance and total tract apparent digestibility -TTAD- of energy and nutrients was studied in Iberian pigs weaned at 28 d of age. There were 12 dietary treatments with 2 type of feeds -high-quality, HQ; and low-quality, LQ-, 2 feed forms -pellets vs. mash-, and 3 durations -7, 14, and 21 d- of supply of the Phase I diets.

Influence of duration of storage on protein quality traits of soybean meals

Two experiments were conducted to determine the influence of duration of storage of soybean meal (SBM) on variables that define the quality of the protein fraction. Urease activity, protein dispersibility index (PDI), KOH protein solubility (KOHsol), and trypsin inhibitor activity were determined. In experiment 1, 8 samples of SBM, ranging in CP content from 55.4 to 56.5% DM, were collected from a US crushing plant at weekly intervals and analyzed at arrival to the laboratory and after 30, 60, 90, and 120 d of storage. In experiment 2, 7 samples of SBM, ranging in CP content from 49.0 to 55.0% DM, were collected from different Argentinean crushers and analyzed at arrival and after 24, 48, 80, and 136 wk of storage. In both experiments, samples were stored in hermetic glass containers in a laboratory room at 12 ± 2°C and a relative humidity of 70 ± 3%. Duration of storage did not affect urease activity or trypsin inhibitor activity values in either of the 2 experiments. However, PDI values decreased linearly with time of storage in both experiments (P menor que 0.001). Also, KOHsol decreased linearly (P menor que 0.05) with duration of storage in experiment 2 (long-term storage) but not in experiment 1(shorter term storage). Therefore, PDI values might not be adequate to compare protein quality of commercial SBM samples that have been stored for different periods of time. The KOHsol values are less affected by length of storage of the meals under current commercial practices.

A toolbox with DERIVE: calculus on several variables, Applications of Computer Algebra

A toolbox is a set of procedures taking advantage of the computing power and graphical capacities of a CAS. With these procedures the students can solve math problems, apply mathematics to engineering or simply reinforce the learning of certain mathematical concepts. From the point of view of their construction, we can consider two types of toolboxes: (i) the closed box, built by the teacher, in which the utility files are provided to the students together with the respective tutorials and several worksheets with proposed exercises and problems,