Localization and Tracking in Energy-Constrained Networks with Dynamic Connectivity

Systems used for target localization, such as goods, individuals, or animals, commonly rely on operational means to meet the final application demands. However, what would happen if some means were powered up randomly by harvesting systems? And what if those devices not randomly powered had their duty cycles restricted? Under what conditions would such an operation be tolerable in localization services? What if the references provided by nodes in a tracking problem were distorted? Moreover, there is an underlying topic common to the previous questions regarding the transfer of conceptual models to reality in field tests: what challenges are faced upon deploying a localization network that integrates energy harvesting modules? The application scenario of the system studied is a traditional herding environment of semi domesticated reindeer (Rangifer tarandus tarandus) in northern Scandinavia. In these conditions, information on approximate locations of reindeer is as important as environmental preservation. Herders also need cost-effective devices capable of operating unattended in, sometimes, extreme weather conditions. The analyses developed are worthy not only for the specific application environment presented, but also because they may serve as an approach to performance of navigation systems in absence of reasonably accurate references like the ones of the Global Positioning System (GPS). A number of energy-harvesting solutions, like thermal and radio-frequency harvesting, do not commonly provide power beyond one milliwatt. When they do, battery buffers may be needed (as it happens with solar energy) which may raise costs and make systems more dependent on environmental temperatures. In general, given our problem, a harvesting system is needed that be capable of providing energy bursts of, at least, some milliwatts. Many works on localization problems assume that devices have certain capabilities to determine unknown locations based on range-based techniques or fingerprinting which cannot be assumed in the approach considered herein. The system presented is akin to range-free techniques, but goes to the extent of considering very low node densities: most range-free techniques are, therefore, not applicable. Animal localization, in particular, uses to be supported by accurate devices such as GPS collars which deplete batteries in, maximum, a few days. Such short-life solutions are not particularly desirable in the framework considered. In tracking, the challenge may times addressed aims at attaining high precision levels from complex reliable hardware and thorough processing techniques. One of the challenges in this Thesis is the use of equipment with just part of its facilities in permanent operation, which may yield high input noise levels in the form of distorted reference points. The solution presented integrates a kinetic harvesting module in some nodes which are expected to be a majority in the network. These modules are capable of providing power bursts of some milliwatts which suffice to meet node energy demands. The usage of harvesting modules in the aforementioned conditions makes the system less dependent on environmental temperatures as no batteries are used in nodes with harvesters--it may be also an advantage in economic terms. There is a second kind of nodes. They are battery powered (without kinetic energy harvesters), and are, therefore, dependent on temperature and battery replacements. In addition, their operation is constrained by duty cycles in order to extend node lifetime and, consequently, their autonomy. There is, in turn, a third type of nodes (hotspots) which can be static or mobile. They are also battery-powered, and are used to retrieve information from the network so that it is presented to users. The system operational chain starts at the kinetic-powered nodes broadcasting their own identifier. If an identifier is received at a battery-powered node, the latter stores it for its records. Later, as the recording node meets a hotspot, its full record of detections is transferred to the hotspot. Every detection registry comprises, at least, a node identifier and the position read from its GPS module by the battery-operated node previously to detection. The characteristics of the system presented make the aforementioned operation own certain particularities which are also studied. First, identifier transmissions are random as they depend on movements at kinetic modules--reindeer movements in our application. Not every movement suffices since it must overcome a certain energy threshold. Second, identifier transmissions may not be heard unless there is a battery-powered node in the surroundings. Third, battery-powered nodes do not poll continuously their GPS module, hence localization errors rise even more. Let's recall at this point that such behavior is tight to the aforementioned power saving policies to extend node lifetime. Last, some time is elapsed between the instant an identifier random transmission is detected and the moment the user is aware of such a detection: it takes some time to find a hotspot. Tracking is posed as a problem of a single kinetically-powered target and a population of battery-operated nodes with higher densities than before in localization. Since the latter provide their approximate positions as reference locations, the study is again focused on assessing the impact of such distorted references on performance. Unlike in localization, distance-estimation capabilities based on signal parameters are assumed in this problem. Three variants of the Kalman filter family are applied in this context: the regular Kalman filter, the alpha-beta filter, and the unscented Kalman filter. The study enclosed hereafter comprises both field tests and simulations. Field tests were used mainly to assess the challenges related to power supply and operation in extreme conditions as well as to model nodes and some aspects of their operation in the application scenario. These models are the basics of the simulations developed later. The overall system performance is analyzed according to three metrics: number of detections per kinetic node, accuracy, and latency. The links between these metrics and the operational conditions are also discussed and characterized statistically. Subsequently, such statistical characterization is used to forecast performance figures given specific operational parameters. In tracking, also studied via simulations, nonlinear relationships are found between accuracy and duty cycles and cluster sizes of battery-operated nodes. The solution presented may be more complex in terms of network structure than existing solutions based on GPS collars. However, its main gain lies on taking advantage of users' error tolerance to reduce costs and become more environmentally friendly by diminishing the potential amount of batteries that can be lost. Whether it is applicable or not depends ultimately on the conditions and requirements imposed by users' needs and operational environments, which is, as it has been explained, one of the topics of this Thesis.

2+2+2 fa molto più di 6 = 2+2+2 is much more than just 6 = CUANDO 2+2+2 SON MUCHO MÁS QUE SOLO 6. Sobre el espacio diagonal concatenado

Nella sua "dichiarazione di poetica", Alberto Campo Baeza confessa che la cosa che più gli sta a cuore è la bellezza, che persegue con le armi della ragione e dell'immaginazione, confortato dalle parole di illustri predecessori, come Cervantes e Goya, Platone e Sant'Agostino, Vitruvio e Keats

Evolutionary computation of forests with Degree- and Role-Constrained Minimum Spanning Trees

Finding the degree-constrained minimum spanning tree (DCMST) of a graph is a widely studied NP-hard problem. One of its most important applications is network design. Here we deal with a new variant of the DCMST problem, which consists of finding not only the degree- but also the role-constrained minimum spanning tree (DRCMST), i.e., we add constraints to restrict the role of the nodes in the tree to root, intermediate or leaf node. Furthermore, we do not limit the number of root nodes to one, thereby, generally, building a forest of DRCMSTs. The modeling of network design problems can benefit from the possibility of generating more than one tree and determining the role of the nodes in the network. We propose a novel permutation-based representation to encode these forests. In this new representation, one permutation simultaneously encodes all the trees to be built. We simulate a wide variety of DRCMST problems which we optimize using eight different evolutionary computation algorithms encoding individuals of the population using the proposed representation. The algorithms we use are: estimation of distribution algorithm, generational genetic algorithm, steady-state genetic algorithm, covariance matrix adaptation evolution strategy, differential evolution, elitist evolution strategy, non-elitist evolution strategy and particle swarm optimization. The best results are for the estimation of distribution algorithms and both types of genetic algorithms, although the genetic algorithms are significantly faster.

A control theoretic approach to solve a constrained uplink power dynamic game

This paper addresses an uplink power control dynamic game where we assume that each user battery represents the system state that changes with time following a discrete-time version of a differential game. To overcome the complexity of the analysis of a dynamic game approach we focus on the concept of Dynamic Potential Games showing that the game can be solved as an equivalent Multivariate Optimum Control Problem. The solution of this problem is quite interesting because different users split the activity in time, avoiding higher interferences and providing a long term fairness.

Análisis, desarrollo y optimización de un sistema para el diseño de redes topográficas valorando el modelo digital del terreno

El presente trabajo tiene como objetivo general el análisis de las técnicas de diseño y optimización de redes topográficas, observadas mediante topografía convencional (no satelital) el desarrollo e implementación de un sistema informático capaz de ayudar a la definición de la geometría más fiable y precisa, en función de la orografía del terreno donde se tenga que ubicar. En primer lugar se realizará un estudio de la metodología del ajuste mediante mínimos cuadrados y la propagación de varianzas, para posteriormente analizar su dependencia de la geometría que adopte la red. Será imprescindible determinar la independencia de la matriz de redundancia (R) de las observaciones y su total dependencia de la geometría, así como la influencia de su diagonal principal (rii), números de redundancia, para garantizar la máxima fiabilidad interna de la misma. También se analizará el comportamiento de los números de redundancia (rii) en el diseño de una red topográfica, la variación de dichos valores en función de la geometría, analizando su independencia respecto de las observaciones así como los diferentes niveles de diseño en función de los parámetros y datos conocidos. Ha de señalarse que la optimización de la red, con arreglo a los criterios expuestos, está sujeta a los condicionantes que impone la necesidad de que los vértices sean accesibles, y además sean visibles entre sí, aquellos relacionados por observaciones, situaciones que dependen esencialmente del relieve del terreno y de los obstáculos naturales o artificiales que puedan existir. Esto implica la necesidad de incluir en el análisis y en el diseño, cuando menos de un modelo digital del terreno (MDT), aunque lo más útil sería la inclusión en el estudio del modelo digital de superficie (MDS), pero esta opción no siempre será posible. Aunque el tratamiento del diseño esté basado en un sistema bidimensional se estudiará la posibilidad de incorporar un modelo digital de superficie (MDS); esto permitirá a la hora de diseñar el emplazamiento de los vértices de la red la viabilidad de las observaciones en función de la orografía y los elementos, tanto naturales como artificiales, que sobre ella estén ubicados. Este sistema proporcionaría, en un principio, un diseño óptimo de una red constreñida, atendiendo a la fiabilidad interna y a la precisión final de sus vértices, teniendo en cuenta la orografía, lo que equivaldría a resolver un planteamiento de diseño en dos dimensiones y media1; siempre y cuando se dispusiera de un modelo digital de superficie o del terreno. Dado que la disponibilidad de obtener de manera libre el MDS de las zonas de interés del proyecto, hoy en día es costoso2, se planteará la posibilidad de conjuntar, para el estudio del diseño de la red, de un modelo digital del terreno. Las actividades a desarrollar en el trabajo de esta tesis se describen en esta memoria y se enmarcan dentro de la investigación para la que se plantean los siguientes objetivos globales: 1. Establecer un modelo matemático del proceso de observación de una red topográfica, atendiendo a todos los factores que intervienen en el mismo y a su influencia sobre las estimaciones de las incógnitas que se obtienen como resultado del ajuste de las observaciones. 2. Desarrollar un sistema que permita optimizar una red topográfica en sus resultados, aplicando técnicas de diseño y simulación sobre el modelo anterior. 3. Presentar una formulación explícita y rigurosa de los parámetros que valoran la fiabilidad de una red topográfica y de sus relaciones con el diseño de la misma. El logro de este objetivo se basa, además de en la búsqueda y revisión de las fuentes, en una intensa labor de unificación de notaciones y de construcción de pasos intermedios en los desarrollos matemáticos. 4. Elaborar una visión conjunta de la influencia del diseño de una red, en los seis siguientes factores (precisiones a posteriori, fiabilidad de las observaciones, naturaleza y viabilidad de las mismas, instrumental y metodología de estacionamiento) como criterios de optimización, con la finalidad de enmarcar el tema concreto que aquí se aborda. 5. Elaborar y programar los algoritmos necesarios para poder desarrollar una aplicación que sea capaz de contemplar las variables planteadas en el apartado anterior en el problema del diseño y simulación de redes topográficas, contemplando el modelo digital de superficie. Podrían considerarse como objetivos secundarios, los siguientes apartados: Desarrollar los algoritmos necesarios para interrelacionar el modelo digital del terreno con los propios del diseño. Implementar en la aplicación informática la posibilidad de variación, por parte del usuario, de los criterios de cobertura de los parámetros (distribución normal o t de Student), así como los grados de fiabilidad de los mismos ABSTRACT The overall purpose of this work is the analysis of the techniques of design and optimization for geodetic networks, measured with conventional survey methods (not satellite), the development and implementation of a computational system capable to help on the definition of the most liable and accurate geometry, depending on the land orography where the network has to be located. First of all, a study of the methodology by least squares adjustment and propagation of variances will be held; then, subsequently, analyze its dependency of the geometry that the network will take. It will be essential to determine the independency of redundancy matrix (R) from the observations and its absolute dependency from the network geometry, as well as the influence of the diagonal terms of the R matrix (rii), redundancy numbers, in order to ensure maximum re liability of the network. It will also be analyzed first the behavior of redundancy numbers (rii) in surveying network design, then the variation of these values depending on the geometry with the analysis of its independency from the observations, and finally the different design levels depending on parameters and known data. It should be stated that network optimization, according to exposed criteria, is subject to the accessibility of the network points. In addition, common visibility among network points, which of them are connected with observations, has to be considered. All these situations depends essentially on the terrain relief and the natural or artificial obstacles that should exist. Therefore, it is necessary to include, at least, a digital terrain model (DTM), and better a digital surface model (DSM), not always available. Although design treatment is based on a bidimensional system, the possibility of incorporating a digital surface model (DSM) will be studied; this will allow evaluating the observations feasibility based on the terrain and the elements, both natural and artificial, which are located on it, when selecting network point locations. This system would provide, at first, an optimal design of a constrained network, considering both the internal reliability and the accuracy of its points (including the relief). This approach would amount to solving a “two and a half dimensional”3 design, if a digital surface model is available. As the availability of free DSM4 of the areas of interest of the project today is expensive, the possibility of combining a digital terrain model will arise. The activities to be developed on this PhD thesis are described in this document and are part of the research for which the following overall objectives are posed: 1. To establish a mathematical model for the process of observation of a survey network, considering all the factors involved and its influence on the estimates of the unknowns that are obtained as a result of the observations adjustment. 2. To develop a system to optimize a survey network results, applying design and simulation techniques on the previous model. 3. To present an explicit and rigorous formulation of parameters which assess the reliability of a survey network and its relations with the design. The achievement of this objective is based, besides on the search and review of sources, in an intense work of unification of notation and construction of intermediate steps in the mathematical developments. 4. To develop an overview of the influence on the network design of six major factors (posterior accuracy, observations reliability, viability of observations, instruments and station methodology) as optimization criteria, in order to define the subject approached on this document. 5. To elaborate and program the algorithms needed to develop an application software capable of considering the variables proposed in the previous section, on the problem of design and simulation of surveying networks, considering the digital surface model. It could be considered as secondary objectives, the following paragraphs: To develop the necessary algorithms to interrelate the digital terrain model with the design ones. To implement in the software application the possibility of variation of the coverage criteria parameters (normal distribution or Student t test) and therefore its degree of reliability.

Development of a fuzzy control based self-adaptive system for energy saving in constrained networks for the Internet of Things

Las redes del futuro, incluyendo las redes de próxima generación, tienen entre sus objetivos de diseño el control sobre el consumo de energía y la conectividad de la red. Estos objetivos cobran especial relevancia cuando hablamos de redes con capacidades limitadas, como es el caso de las redes de sensores inalámbricos (WSN por sus siglas en inglés). Estas redes se caracterizan por estar formadas por dispositivos de baja o muy baja capacidad de proceso y por depender de baterías para su alimentación. Por tanto la optimización de la energía consumida se hace muy importante. Son muchas las propuestas que se han realizado para optimizar el consumo de energía en este tipo de redes. Quizás las más conocidas son las que se basan en la planificación coordinada de periodos de actividad e inactividad, siendo una de las formas más eficaces para extender el tiempo de vida de las baterías. La propuesta que se presenta en este trabajo se basa en el control de la conectividad mediante una aproximación probabilística. La idea subyacente es que se puede esperar que una red mantenga la conectividad si todos sus nodos tienen al menos un número determinado de vecinos. Empleando algún mecanismo que mantenga ese número, se espera que se pueda mantener la conectividad con un consumo energético menor que si se empleara una potencia de transmisión fija que garantizara una conectividad similar. Para que el mecanismo sea eficiente debe tener la menor huella posible en los dispositivos donde se vaya a emplear. Por eso se propone el uso de un sistema auto-adaptativo basado en control mediante lógica borrosa. En este trabajo se ha diseñado e implementado el sistema descrito, y se ha probado en un despliegue real confirmando que efectivamente existen configuraciones posibles que permiten mantener la conectividad ahorrando energía con respecto al uso de una potencia de transmisión fija. ABSTRACT. Among the design goals for future networks, including next generation networks, we can find the energy consumption and the connectivity. These two goals are of special relevance when dealing with constrained networks. That is the case of Wireless Sensors Networks (WSN). These networks consist of devices with low or very low processing capabilities. They also depend on batteries for their operation. Thus energy optimization becomes a very important issue. Several proposals have been made for optimizing the energy consumption in this kind of networks. Perhaps the best known are those based on the coordinated planning of active and sleep intervals. They are indeed one of the most effective ways to extend the lifetime of the batteries. The proposal presented in this work uses a probabilistic approach to control the connectivity of a network. The underlying idea is that it is highly probable that the network will have a good connectivity if all the nodes have a minimum number of neighbors. By using some mechanism to reach that number, we hope that we can preserve the connectivity with a lower energy consumption compared to the required one if a fixed transmission power is used to achieve a similar connectivity. The mechanism must have the smallest footprint possible on the devices being used in order to be efficient. Therefore a fuzzy control based self-adaptive system is proposed. This work includes the design and implementation of the described system. It also has been validated in a real scenario deployment. We have obtained results supporting that there exist configurations where it is possible to get a good connectivity saving energy when compared to the use of a fixed transmission power for a similar connectivity.