A Knowledge Model for Automatic Configuration of Traffic Messages

This paper describes a knowledge model for a configuration problem in the do-main of traffic control. The goal of this model is to help traffic engineers in the dynamic selection of a set of messages to be presented to drivers on variable message signals. This selection is done in a real-time context using data recorded by traffic detectors on motorways. The system follows an advanced knowledge-based solution that implements two abstract problem solving methods according to a model-based approach recently proposed in the knowledge engineering field. Finally, the paper presents a discussion about the advantages and drawbacks found for this problem as a consequence of the applied knowledge modeling ap-proach.

Selective ablation with UV lasers of a-Si:H thin film solar cells in direct scribing configuration

Monolithical series connection of silicon thin-film solar cells modules performed by laser scribing plays a very important role in the entire production of these devices. In the current laser process interconnection the two last steps are developed for a configuration of modules where the glass is essential as transparent substrate. In addition, the change of wavelength in the employed laser sources is sometimes enforced due to the nature of the different materials of the multilayer structure which make up the device. The aim of this work is to characterize the laser patterning involved in the monolithic interconnection process in a different configurations of processing than the usually performed with visible laser sources. To carry out this study, we use nanosecond and picosecond laser sources working at 355nm of wavelength in order to achieve the selective ablation of the material from the film side. To assess this selective removal of material has been used EDX (energy dispersive using X-ray) analysis

A method for Kinematic Calibration of a Parallel Robot by using one camera in hand and a spherical object

The main purpose of robot calibration is the correction of the possible errors in the robot parameters. This paper presents a method for a kinematic calibration of a parallel robot that is equipped with one camera in hand. In order to preserve the mechanical configuration of the robot, the camera is utilized to acquire incremental positions of the end effector from a spherical object that is fixed in the word reference frame. The positions of the end effector are related to incremental positions of resolvers of the motors of the robot, and a kinematic model of the robot is used to find a new group of parameters which minimizes errors in the kinematic equations. Additionally, properties of the spherical object and intrinsic camera parameters are utilized to model the projection of the object in the image and improving spatial measurements. Finally, the robotic system is designed to carry out tracking tasks and the calibration of the robot is validated by means of integrating the errors of the visual controller.

Implicaciones de la accesibilidad configuracional en la movilidad peatonal. El caso de Madrid = The implications of configurational accessibility in pedestrian mobility. The case of Madrid

- Resumen La hipótesis que anima esta tesis doctoral es que algunas de las características del entorno urbano, en particular las que describen la accesibilidad de su red de espacio público, podrían estar relacionadas con la proporción de viajes a pie o reparto modal, que tiene cada zona o barrio de Madrid. Uno de los puntos de partida de dicha hipótesis que el entorno urbano tiene una mayor influencia sobre los viaje a pie que en sobre otros modos de transporte, por ejemplo que en los viajes de bicicleta o en transporte público; y es que parece razonable suponer que estos últimos van a estar más condicionadas por ejemplo por la disponibilidad de vías ciclistas, en el primer caso, o por la existencia de un servicio fiable y de calidad, en el segundo. Otra de las motivaciones del trabajo es que la investigación en este campo de la accesibilidad del espacio público, en concreto la denominada “Space Syntax”, ha probado en repetidas ocasiones la influencia de la red de espacio público en cómo se distribuye la intensidad del tráfico peatonal por la trama urbana, pero no se han encontrado referencias de la influencia de dicho elemento sobre el reparto modal. De acuerdo con la hipótesis y con otros trabajos anteriores se propone una metodología basada en el análisis empírico y cuantitativo. Su objetivo es comprobar si la red de espacio público, independientemente de otras variables como los usos del suelo, incluso de las variables de ajenas entorno no construido, como las socioeconómicas, está o no relacionada estadísticamente con la proporción de peatones viajes en las zonas urbanas. Las técnicas estadísticas se utilizan para comprobar sistemáticamente la asociación de las variables del entorno urbano, denominadas variables independientes, con el porcentaje de viajes a pie, la variable dependiente. En términos generales, la metodología es similar a la usada en otros trabajos en este campo como los de CERVERÓ y KOCKLEMAN (1997), CERVERÓ y DUNCAN (2003), o para los que se utilizan principalmente en la revisión general de TRB (2005) o, más recientemente, en ZEGRAS (2006) o CHATMAN (2009). Otras opciones metodológicas, como los métodos de preferencias declaradas (ver LOUVIERE, HENSHER y SWAIT, 2000) o el análisis basado en agentes (PENN & TURNER, 2004) fueron descartados, debido a una serie de razones, demasiado extensas para ser descritas aquí. El caso de estudio utilizado es la zona metropolitana de Madrid, abarcándola hasta la M-50, es decir en su mayor parte, con un tamaño aproximado de 31x34 Km y una población de 4.132.820 habitantes (aproximadamente el 80% de la población de la región). Las principales fuentes de datos son la Encuesta Domiciliaria de Movilidad de 2004 (EDM04), del Consorcio Regional de Transportes de Madrid que es la última disponible (muestra: > 35.000 familias,> 95.000 personas), y un modelo espacial del área metropolitana, integrando el modelo para calcular los índices de Space Syntax y un Sistema de Información Geográfica (SIG). La unidad de análisis, en este caso las unidades espaciales, son las zonas de transporte (con una población media de 7.063 personas) y los barrios (con una población media de 26.466 personas). Las variables del entorno urbano son claramente el centro del estudio. Un total de 20 índices (de 21) se seleccionan de entre los más relevantes encontrados en la revisión de la producción científica en este campo siendo que, al mismo tiempo, fueran accesibles. Nueve de ellos se utilizan para describir las características de los usos del suelo, mientras que otros once se usan para describir la red de espacios públicos. Estos últimos incluyen las variables de accesibilidad configuracional, que son, como se desprende de su título, el centro del estudio propuesto. La accesibilidad configuracional es un tipo especial de accesibilidad que se basa en la configuración de la trama urbana, según esta fue definida por HILLIER (1996), el autor de referencia dentro de esta línea de investigación de Space Syntax. Además se incluyen otras variables de la red de espacio público más habituales en los estudios de movilidad, y que aquí se denominan características geométricas de los elementos de la red, tales como su longitud, tipo de intersección, conectividad, etc. Por último se incluye además una variable socioeconómica, es decir ajena al entorno urbano, para evaluar la influencia de los factores externos, pues son varios los que pueden tener un impacto en la decisión de caminar (edad, género, nivel de estudios, ingresos, tasa de motorización, etc.). La asociación entre las variables se han establecido usando análisis de correlación (bivariante) y modelos de análisis multivariante. Las primeras se calculan entre por pares entre cada una de las 21 variables independientes y la dependiente, el porcentaje de viajes a pie. En cuanto a los segundos, se han realizado tres tipos de estudios: modelo multivariante general lineal, modelo multivariante general curvilíneo y análisis discriminante. Todos ellos son capaces de generar modelos de asociación entre diversas variables, pudiéndose de esta manera evaluar con bastante precisión en qué medida cada modelo reproduce el comportamiento de la variable dependiente, y además, el peso o influencia de cada variable en el modelo respecto a las otras. Los resultados fundamentales del estudio se expresan en dos modelos finales alternativos, que demuestran tener una significativa asociación con el porcentaje de viajes a pie (R2 = 0,6789, p <0,0001), al explicar las dos terceras partes de su variabilidad. En ellos, y en general en todo el estudio realizado, se da una influencia constante de tres índices en particular, que quedan como los principales. Dos de ellos, de acuerdo con muchos de los estudios previos, corresponden a la densidad y la mezcla de usos del suelo. Pero lo más novedoso de los resultados obtenidos es que el tercero es una medida de la accesibilidad de la red de espacio público, algo de lo que no había referencias hasta ahora. Pero, ¿cuál es la definición precisa y el peso relativo de cada uno en el modelo, es decir, en la variable independiente? El de mayor peso en la mayor parte de los análisis realizados es el índice de densidad total (n º residentes + n º puestos de trabajo + n º alumnos / Ha). Es decir, una densidad no sólo de población, sino que incluye algunas de las actividades más importantes que pueden darse una zona para generar movilidad a pie. El segundo que mayor peso adquiere, llegando a ser el primero en alguno de los análisis estadísticos efecturados, es el índice de accesibuilidad configuracional denominado integración de radio 5. Se trata de una medida de la accesibilidad de la zona, de su centralidad, a la escala de, más un menor, un distrito o comarca. En cuanto al tercero, obtiene una importancia bastante menor que los anteriores, y es que representa la mezcla de usos. En concreto es una medida del equilibrio entre los comercios especializados de venta al por menor y el número de residentes (n º de tiendas especializadas en alimentación, bebidas y tabaco / n º de habitantes). Por lo tanto, estos resultados confirman buena parte de los de estudios anteriores, especialmente los relativas a los usos del suelo, pero al mismo tiempo, apuntan a que la red de espacio público podría tener una influir mayor de la comprobada hasta ahora en la proporción de peatones sobre el resto de modos de transportes. Las razones de por qué esto puede ser así, se discuten ampliamente en las conclusiones. Finalmente se puede precisar que dicha conclusión principal se refiere a viajes de una sola etapa (no multimodales) que se dan en los barrios y zonas del área metropolitana de Madrid. Por supuesto, esta conclusión tiene en la actualidad, una validez limitada, ya que es el resultado de un solo caso — Abstract The research hypothesis for this Ph.D. Thesis is that some characteristics of the built environment, particularly those describing the accessibility of the public space network, could be associated with the proportion of pedestrians in all trips (modal split), found in the different parts of a city. The underlying idea is that walking trips are more sensitive to built environment than those by other transport modes, such as for example those by bicycle or by public transport, which could be more conditioned by, e.g. infrastructure availability or service frequency and quality. On the other hand, it has to be noted that the previously research on this field, in particular within Space Syntax’s where this study can be referred, have tested similar hypothesis using pedestrian volumes as the dependent variable, but never against modal split. According to such hypothesis, research methodology is based primarily on empirical quantitative analysis, and it is meant to be able to assess whether public space network, no matter other built environment and non-built environment variables, could have a relationship with the proportion of pedestrian trips in urban areas. Statistical techniques are used to check the association of independent variables with the percentage of walking in all trips, the dependent one. Broadly speaking this methodology is similar to that of previous studies in the field such as CERVERO&KOCKLEMAN (1997), CERVERO & DUNCAN (2003), or to those used mainly in the general review of T.R.B. (2005) or, more recently in ZEGRAS (2006) or CHATMAN (2009). Other methodological options such as stated choice methods (see LOUVIERE, HENSHER & SWAIT, 2000) or agent based analysis (PENN & TURNER, 2004), were discarded, due to a number of reasons, too long to be described here. The case study is not the entire Madrid’s metropolitan area, but almost (4.132.820 inhabitants, about 80% of region´s population). Main data sources are the Regional Mobility Home Based Survey 2004 (EDM04), which is the last available (sample: >35.000 families, > 95.000 individuals), and a spatial model of the metropolitan area, developed using Space Syntax and G.I.S. techniques. The analysis unit, in this case spatial units, are both transport zones (mean population = 7.063) and neighborhoods (mean population = 26.466). The variables of the built environment are clearly the core of the study. A total of 20 (out of 21) are selected from among those found in the literature while, at the same time, being accessible. Nine out of them are used to describe land use characteristics while another eleven describe the network of public spaces. Latter ones include configurational accessibility or Space Syntax variables. This is a particular sort of accessibility related with the concept of configuration, by HILLIER (1996), one of the main authors of Space Syntax, But it also include more customary variables used in mobility research to describe the urban design or spatial structure (here public space network), which here are called geometric characteristics of the such as its length, type of intersection, conectivity, density, etc. Finally a single socioeconomic variable was included in order to assess the influence non built environment factors that also may have an impact on walking (age, income, motorization rate, etc.). The association among variables is worked out using bi-variate correlation analysis and multivariate-analysis. Correlations are calculated among the 21 independent variables and the dependent one, the percentage of walking trips. Then, three types of multi-variate studies are run: general linear, curvilinear and discriminant multi-variate analysis. The latter are fully capable of generating complex association models among several variables, assessing quite precisely to what extent each model reproduces the behavior of the dependent variable, and also the weight or influence of each variable in the model. This study’s results show a consistent influence of three particular indexes in the two final alternative models of the multi-variate study (best, R2=0,6789, p<0,0000). Not surprisingly, two of them correspond to density and mix of land uses. But perhaps more interesting is that the third one is a measure of the accessibility of the public space network, a variable less important in the literature up to now. Additional precisions about them and their relative weight could also be of some interest. The density index is not only about population but includes most important activities in an area (nº residents + nº jobs+ nº students/Ha). The configurational index (radius 5 integration) is a measure of the accessibility of the area, i.e. centrality, at the scale of, more a less, a district. Regarding the mix of land uses index, this one is a measure of the balance between retail, in fact local basic retail, and the number of residents (nº of convenience shops / nº of residents). Referring to their weights, configurational index (radius 5 integration) gets the higher standardized coefficient of the final equation. However, in the final equations, there are a higher number of indexes coming from the density or land use mix categories than from public space network enter. Therefore, these findings seem to support part of the field’s knowledge, especially those concerning land uses, but at the same time they seem to bring in the idea that the configuration of the urban grid could have an influence in the proportion of walkers (as a part of total trips on any transport mode) that do single journey trips in the neighborhoods of Madrid, Spain. Of course this conclusion has, at present, a limited validity since it’s the result of a single case. The reasons of why this can be so, are discussed in the last part of the thesis.

A Web Implementation of A Generalized NEP

The Networks of Evolutionary Processors (NEPs) are computing mechanisms directly inspired from the behavior of cell populations more specifically the point mutations in DNA strands. These mechanisms are been used for solving NP-complete problems by means of a parallel computation postulation. This paper describes an implementation of the basic model of NEP using Web technologies and includes the possibility of designing some of the most common variants of it by means the use of the web page design which eases the configuration of a given problem. It is a system intended to be used in a multicore processor in order to benefit from the multi thread use.

Numerical simulation of tangling in jet engine turbines

The numerical analysis of certain safety related problems presents serious difficulties, since the large number of components present leads to huge finite elementmodels that can only be solved by using large and expensive computers or by making rough approaches to the problem. Tangling, or clashing, in the turbine of a jet engine airplane is an example of such problems. This is caused by the crash and friction between rotor and stator blades in the turbine after an eventual shaft failure. When facing the study of an event through numerical modelling, the accurate simulation of this problem would require the engineer to model all the rotor and stator blades existing in the turbine stage, using a small element size in all pieces. Given that the number of stator and rotor blades is usually around 200, such simulations would require millions of elements. This work presents a new numerical methodology, specifically developed for the accurate modelling of the tangling problem that, depending on the turbine configuration, is able to reduce the number of nodes up to an order of magnitude without losing accuracy. The methodology, which benefits from the cyclic configuration of turbines, is successfully applied to the numerical analysis of a hypothetical tangling event in a turbine, providing valuable data such as the rotating velocity decrease of the turbine, the braking torque and the damage suffered by the blades. The methodology is somewhat general and can be applied to any problem in which damage caused by the interaction between a rotating and static piece is to be analysed.

Study of the Electrical Behavior in Intermediate Band-Si Junctions

In this study we analyze the electrical behavior of a junction formed by an ultraheavily Ti implanted Si layer processed by a Pulsed Laser Melting (PLM) and the non implanted Si substrate. This electrical behavior exhibits an electrical decoupling effect in this bilayer that we have associated to an Intermediate Band (IB) formation in the Ti supersaturated Si layer. Time-of-flight secondary ion mass spectrometry (ToFSIMS) measurements show a Ti depth profile with concentrations well above the theoretical limit required to the IB formation. Sheet resistance and Hall mobility measurements in the van der Pauw configuration of these bilayers exhibit a clear dependence with the different measurement currents introduced (1menor queA-1mA). We find that the electrical transport properties measured present an electrical decoupling effect in the bilayer as function of the temperature. The dependence of this effect with the injected current could be explained in terms of an additional current flow in the junction from the substrate to the IB layer and in terms of the voltage dependence in the junction with the measurement current.

Total switching of unpolarized light with an electrooptic liquid-crystal device

This paper reports a new family of multimode fiber-optic switching devices based on nematic liquid crystal devices reported by us previously. These devices have a wedged structure as the main characteristic. Several modes of behavior cart arise depending on the internal configuration of the molecules. As we show, fhey have the possibility of total switching of unpolarized light with a very simple structure, low insertion losses, and very low operating voltages These new devices should find a wide range of applications in fiber-optic communication systems.

Trade-off aproaches for the vibroacoustic analysis of trains

Passengers’ comfort in terms of acoustic noise levels is a key design driver for train design. The problem is especially relevant for high speed trains, where the aerodynamic induced noise is dominant, but it is also important for medium speed trains where the mechanical sources of noise may have more influence. The numerical interior noise prediction inside the train is a very comp lex problem, involving many different parameters: complex geometries and materials, different noise sources, com- plex interactions among those sources, broad range of frequencies where the phenomenon is important, etc. In this paper, the main findings of this work developed at IDR/UPM (Instituto de Microgravedad “Ignacio Da Riva”, Universidad Politécnica de Madrid) are presented, concentrat ing on the different modelling methodologies used for the different frequency ranges of interest, from FEM-BEM models, hybrid FEM-SEA to pure SEA models. The advantages and disadvantages of the different approaches are summarized. Different modelling techniques have also been evaluated and compared, taking into account the various and specific geometrical configurations typical in this type of structures, and the material properties used in the models. The critical configuration of the train inside a tunnel is studied in order to evaluate the external loads due to noise sources of the train. In this work, a SEA-model composed by periodic characteristic sections of a high spee d train is analysed inside a tunnel.

Electronic properties of doped magnesium thioindate ternary spinel in the normal and in the inverse structure

We present a theoretical study of the structural and electronic properties of the M-doped MgIn2S4 ternary spinel semiconductor with M = V, Cr, and Mn. All substitutions, in the normal and in the inverse structure, are analyzed. Some of these possible substitutions present intermediate-band states in the band gap with a different occupation for a spin component. It increases the possibilities of inter-band transitions and could be interesting for applications in optoelectronic devices. The contribution to, and the electronic configuration of, these intermediate bands for the octahedral and tetrahedral sites is analyzed and discussed. The study of the substitutional energies indicates that these substitutions are favorable. Comparison between the pure and doped hosts absorption coefficients shows that this deeper band opens up more photon absorption channels and could therefore increase the solar-light absorption with respect to the host.

Fast ignition driven by quasi-monoenergetic ions: Optimal ion type and reduction of ignition energies with an ion beam array

Fast ignition of inertial fusion targets driven by quasi-monoenergetic ion beams is investigated by means of numerical simulations. Light and intermediate ions such as lithium, carbon, aluminum and vanadium have been considered. Simulations show that the minimum ignition energies of an ideal configuration of compressed Deuterium-Tritium are almost independent on the ion atomic number. However, they are obtained for increasing ion energies, which scale, approximately, as Z2, where Z is the ion atomic number. Assuming that the ion beam can be focused into 10 ?m spots, a new irradiation scheme is proposed to reduce the ignition energies. The combination of intermediate Z ions, such as 5.5 GeV vanadium, and the new irradiation scheme allows a reduction of the number of ions required for ignition by, roughly, three orders of magnitude when compared with the standard proton fast ignition scheme.

Tailoring the magnetic anisotropy and domain patterns of sputtered TbFeGa alloys

We report the magnetic anisotropy and domain configuration of cosputtered TbFeGa alloys. The layers were deposited from two targets with compositions TbFe2 and Fe3Ga, respectively. The structural and magnetic properties do not only depend on the composition but also on the growth conditions. Alloys with the same composition but deposited using a DC or a pulsed power source in the TbFe2 target exhibit a different magnetic anisotropy. The perpendicular magnetic anisotropy, the size and topology of domain patterns can be tailored by changing the evaporation parameters of TbFe2. The width of the stripe domain increases from 235 to 835 nm when using the DC source in the TbFe2. We correlate this effect with Tb enrichment of the TbxFe1−x phases present in the samples.

Feasibility assessment of the interactive use of a Monte Carlo algorithm in treatment planning for intraoperative electron radiation therapy

This work analysed the feasibility of using a fast, customized Monte Carlo (MC) method to perform accurate computation of dose distributions during pre- and intraplanning of intraoperative electron radiation therapy (IOERT) procedures. The MC method that was implemented, which has been integrated into a specific innovative simulation and planning tool, is able to simulate the fate of thousands of particles per second, and it was the aim of this work to determine the level of interactivity that could be achieved. The planning workflow enabled calibration of the imaging and treatment equipment, as well as manipulation of the surgical frame and insertion of the protection shields around the organs at risk and other beam modifiers. In this way, the multidisciplinary team involved in IOERT has all the tools necessary to perform complex MC dosage simulations adapted to their equipment in an efficient and transparent way. To assess the accuracy and reliability of this MC technique, dose distributions for a monoenergetic source were compared with those obtained using a general-purpose software package used widely in medical physics applications. Once accuracy of the underlying simulator was confirmed, a clinical accelerator was modelled and experimental measurements in water were conducted. A comparison was made with the output from the simulator to identify the conditions under which accurate dose estimations could be obtained in less than 3 min, which is the threshold imposed to allow for interactive use of the tool in treatment planning. Finally, a clinically relevant scenario, namely early-stage breast cancer treatment, was simulated with pre- and intraoperative volumes to verify that it was feasible to use the MC tool intraoperatively and to adjust dose delivery based on the simulation output, without compromising accuracy. The workflow provided a satisfactory model of the treatment head and the imaging system, enabling proper configuration of the treatment planning system and providing good accuracy in the dosage simulation.

Atomistic modeling of Ge damage accumulation, amorphization and solid phase epitaxial regrowth

En los últimos años, el Ge ha ganado de nuevo atención con la finalidad de ser integrado en el seno de las existentes tecnologías de microelectrónica. Aunque no se le considera como un canddato capaz de reemplazar completamente al Si en el futuro próximo, probalemente servirá como un excelente complemento para aumentar las propiedades eléctricas en dispositivos futuros, especialmente debido a su alta movilidad de portadores. Esta integración requiere de un avance significativo del estado del arte en los procesos de fabricado. Técnicas de simulación, como los algoritmos de Monte Carlo cinético (KMC), proporcionan un ambiente atractivo para llevar a cabo investigación y desarrollo en este campo, especialmente en términos de costes en tiempo y financiación. En este estudio se han usado, por primera vez, técnicas de KMC con el fin entender el procesado “front-end” de Ge en su fabricación, específicamente la acumulación de dañado y amorfización producidas por implantación iónica y el crecimiento epitaxial en fase sólida (SPER) de las capas amorfizadas. Primero, simulaciones de aproximación de clisiones binarias (BCA) son usadas para calcular el dañado causado por cada ión. La evolución de este dañado en el tiempo se simula usando KMC sin red, o de objetos (OKMC) en el que sólamente se consideran los defectos. El SPER se simula a través de una aproximación KMC de red (LKMC), siendo capaz de seguir la evolución de los átomos de la red que forman la intercara amorfo/cristalina. Con el modelo de amorfización desarrollado a lo largo de este trabajo, implementado en un simulador multi-material, se pueden simular todos estos procesos. Ha sido posible entender la acumulación de dañado, desde la generación de defectos puntuales hasta la formación completa de capas amorfas. Esta acumulación ocurre en tres regímenes bien diferenciados, empezando con un ritmo lento de formación de regiones de dañado, seguido por una rápida relajación local de ciertas áreas en la fase amorfa donde ambas fases, amorfa y cristalina, coexisten, para terminar en la amorfización completa de capas extensas, donde satura el ritmo de acumulación. Dicha transición ocurre cuando la concentración de dañado supera cierto valor límite, el cual es independiente de las condiciones de implantación. Cuando se implantan los iones a temperaturas relativamente altas, el recocido dinámico cura el dañado previamente introducido y se establece una competición entre la generación de dañado y su disolución. Estos efectos se vuelven especialmente importantes para iones ligeros, como el B, el cual crea dañado más diluido, pequeño y distribuido de manera diferente que el causado por la implantación de iones más pesados, como el Ge. Esta descripción reproduce satisfactoriamente la cantidad de dañado y la extensión de las capas amorfas causadas por implantación iónica reportadas en la bibliografía. La velocidad de recristalización de la muestra previamente amorfizada depende fuertemente de la orientación del sustrato. El modelo LKMC presentado ha sido capaz de explicar estas diferencias entre orientaciones a través de un simple modelo, dominado por una única energía de activación y diferentes prefactores en las frecuencias de SPER dependiendo de las configuraciones de vecinos de los átomos que recristalizan. La formación de maclas aparece como una consecuencia de esta descripción, y es predominante en sustratos crecidos en la orientación (111)Ge. Este modelo es capaz de reproducir resultados experimentales para diferentes orientaciones, temperaturas y tiempos de evolución de la intercara amorfo/cristalina reportados por diferentes autores. Las parametrizaciones preliminares realizadas de los tensores de activación de tensiones son también capaces de proveer una buena correlación entre las simulaciones y los resultados experimentales de velocidad de SPER a diferentes temperaturas bajo una presión hidrostática aplicada. Los estudios presentados en esta tesis han ayudado a alcanzar un mejor entendimiento de los mecanismos de producción de dañado, su evolución, amorfización y SPER para Ge, además de servir como una útil herramienta para continuar el trabajo en este campo. In the recent years, Ge has regained attention to be integrated into existing microelectronic technologies. Even though it is not thought to be a feasible full replacement to Si in the near future, it will likely serve as an excellent complement to enhance electrical properties in future devices, specially due to its high carrier mobilities. This integration requires a significant upgrade of the state-of-the-art of regular manufacturing processes. Simulation techniques, such as kinetic Monte Carlo (KMC) algorithms, provide an appealing environment to research and innovation in the field, specially in terms of time and funding costs. In the present study, KMC techniques are used, for the first time, to understand Ge front-end processing, specifically damage accumulation and amorphization produced by ion implantation and Solid Phase Epitaxial Regrowth (SPER) of the amorphized layers. First, Binary Collision Approximation (BCA) simulations are used to calculate the damage caused by every ion. The evolution of this damage over time is simulated using non-lattice, or Object, KMC (OKMC) in which only defects are considered. SPER is simulated through a Lattice KMC (LKMC) approach, being able to follow the evolution of the lattice atoms forming the amorphous/crystalline interface. With the amorphization model developed in this work, implemented into a multi-material process simulator, all these processes can be simulated. It has been possible to understand damage accumulation, from point defect generation up to full amorphous layers formation. This accumulation occurs in three differentiated regimes, starting at a slow formation rate of the damage regions, followed by a fast local relaxation of areas into the amorphous phase where both crystalline and amorphous phases coexist, ending in full amorphization of extended layers, where the accumulation rate saturates. This transition occurs when the damage concentration overcomes a certain threshold value, which is independent of the implantation conditions. When implanting ions at relatively high temperatures, dynamic annealing takes place, healing the previously induced damage and establishing a competition between damage generation and its dissolution. These effects become specially important for light ions, as B, for which the created damage is more diluted, smaller and differently distributed than that caused by implanting heavier ions, as Ge. This description successfully reproduces damage quantity and extension of amorphous layers caused by means of ion implantation reported in the literature. Recrystallization velocity of the previously amorphized sample strongly depends on the substrate orientation. The presented LKMC model has been able to explain these differences between orientations through a simple model, dominated by one only activation energy and different prefactors for the SPER rates depending on the neighboring configuration of the recrystallizing atoms. Twin defects formation appears as a consequence of this description, and are predominant for (111)Ge oriented grown substrates. This model is able to reproduce experimental results for different orientations, temperatures and times of evolution of the amorphous/crystalline interface reported by different authors. Preliminary parameterizations for the activation strain tensors are able to also provide a good match between simulations and reported experimental results for SPER velocities at different temperatures under the appliance of hydrostatic pressure. The studies presented in this thesis have helped to achieve a greater understanding of damage generation, evolution, amorphization and SPER mechanisms in Ge, and also provide a useful tool to continue research in this field.

A proposal for a model-based approach for adapting software configuration to runtime environments

Las metodologías de desarrollo ágiles han sufrido un gran auge en entornos industriales durante los últimos años debido a la rapidez y fiabilidad de los procesos de desarrollo que proponen. La filosofía DevOps y específicamente las metodologías derivadas de ella como Continuous Delivery o Continuous Deployment promueven la gestión completamente automatizada del ciclo de vida de las aplicaciones, desde el código fuente a las aplicaciones ejecutándose en entornos de producción. La automatización se ve como un medio para producir procesos repetibles, fiables y rápidos. Sin embargo, no todas las partes de las metodologías Continuous están completamente automatizadas. En particular, la gestión de la configuración de los parámetros de ejecución es un problema que ha sido acrecentado por la elasticidad y escalabilidad que proporcionan las tecnologías de computación en la nube. La mayoría de las herramientas de despliegue actuales pueden automatizar el despliegue de la configuración de parámetros de ejecución, pero no ofrecen soporte a la hora de fijar esos parámetros o de validar los ficheros que despliegan, principalmente debido al gran abanico de opciones de configuración y el hecho de que el valor de muchos de esos parámetros es fijado en base a preferencias expresadas por el usuario. Esto hecho hace que pueda parecer que cualquier solución al problema debe estar ajustada a una aplicación específica en lugar de ofrecer una solución general. Con el objetivo de solucionar este problema, propongo un modelo de configuración que puede ser inferido a partir de instancias de configuración existentes y que puede reflejar las preferencias de los usuarios para ser usado para facilitar los procesos de configuración. El modelo de configuración puede ser usado como la base de un proceso de configuración interactivo capaz de guiar a un operador humano a través de la configuración de una aplicación para su despliegue en un entorno determinado o para detectar cambios de configuración automáticamente y producir una configuración válida que se ajuste a esos cambios. Además, el modelo de configuración debería ser gestionado como si se tratase de cualquier otro artefacto software y debería ser incorporado a las prácticas de gestión habituales. Por eso también propongo un modelo de gestión de servicios que incluya información relativa a la configuración de parámetros de ejecución y que además es capaz de describir y gestionar propuestas arquitectónicas actuales tales como los arquitecturas de microservicios. ABSTRACT Agile development methodologies have risen in popularity within the industry in recent years due to the speed and reliability of the processes they propose. The DevOps philosophy and specifically the methodologies derived from it such as Continuous Delivery and Continuous Deployment push for a totally automated management of the application lifecycle, from the source code to the software running in production environment. Automation in this regard is used as a means to produce repeatable, reliable and fast processes. However, not all parts of the Continuous methodologies are completely automatized. In particular, management of runtime parameter configuration is a problem that has increased its impact in deployment process due to the scalability and elasticity provided by cloud technologies. Most deployment tools nowadays can automate the deployment of runtime parameter configuration, but they offer no support for parameter setting o configuration validation, as the range of different configuration options and the fact that the value of many of those parameters is based on user preference seems to imply that any solution to the problem will have to be tailored to a specific application. With the aim to solve this problem I propose a configuration model that can be inferred from existing configurations and reflect user preferences in order to ease the configuration process. The configuration model can be used as the base of an interactive configuration process capable of guiding a human operator through the configuration of an application for its deployment in a specific environment or to automatically detect configuration changes and produce valid runtime parameter configurations that take into account those changes. Additionally, the configuration model should be managed as any other software artefact and should be incorporated into current management practices. I also propose a service management model that includes the configuration information and that is able to describe and manage current architectural practices such as the microservices architecture.