Underground parking structure built with deep foundations and vault precast elements in Spain

In many cases the only places available for the construction of a new car park are the existing streets or roads. These streets may also have important or historic buildings very close to the structure, which means that they cannot be disturbed in any way during the construction of the parking structure. In many cases the only places available for the construction of a new car park are the existing streets or roads. These streets may also have important or historic buildings very close to the structure, which means that they cannot be disturbed in any way during the construction of the parking structure.

Adverse aerodynamics effects of a high speed train under the influence of cross winds, analysis and optimization of wind fence

The research work that here is summarized, it is classed on the area of dynamics and measures of railway safety, specifically in the study of the influence of the cross wind on the high-speed trains as well as the study of new mitigation measures like wind breaking structures or wind fences, with optimized shapes. The work has been developed in the Research Center in Rail Technology (CITEF), and supported by the Universidad Politécnica de Madrid, Spain.

Application of virtual certification techniques to vehicle design and track maintenance

Virtual certification partially substitutes by computer simulations the experimental techniques required for rail vehicle certification. In this paper, several works were these techniques were used in the vehicle design and track maintenance processes are presented. Dynamic simulation of multibody systems was used to virtually apply the EN14363 standard to certify the dynamic behaviour of vehicles. The works described are: assessment of a freight bogie design adapted to meter-gauge, assessment of a railway track layout for a subway network, freight bogie design with higher speed and axle load, and processing of the data acquired by a track recording vehicle for track maintenance.

Floating car data augmentation based on infrastructure sensors and neural networks

The development of new-generation intelligent vehicle technologies will lead to a better level of road safety and CO2 emission reductions. However, the weak point of all these systems is their need for comprehensive and reliable data. For traffic data acquisition, two sources are currently available: 1) infrastructure sensors and 2) floating vehicles. The former consists of a set of fixed point detectors installed in the roads, and the latter consists of the use of mobile probe vehicles as mobile sensors. However, both systems still have some deficiencies. The infrastructure sensors retrieve information fromstatic points of the road, which are spaced, in some cases, kilometers apart. This means that the picture of the actual traffic situation is not a real one. This deficiency is corrected by floating cars, which retrieve dynamic information on the traffic situation. Unfortunately, the number of floating data vehicles currently available is too small and insufficient to give a complete picture of the road traffic. In this paper, we present a floating car data (FCD) augmentation system that combines information fromfloating data vehicles and infrastructure sensors, and that, by using neural networks, is capable of incrementing the amount of FCD with virtual information. This system has been implemented and tested on actual roads, and the results show little difference between the data supplied by the floating vehicles and the virtual vehicles.

On the importance of shrub encroachment by sprouters, climate, species richness and anthropic factors for ecosystem multifunctionality in semi-arid Mediterranean ecosystems

One of the most important changes taking place in drylands worldwide is the increase of the cover and dominance of shrubs in areas formerly devoid of them (shrub encroachment). A large body of research has evaluated the causes and consequences of shrub encroachment for both ecosystem structure and functioning. However, there are virtually no studies evaluating how shrub encroachment affects the ability of ecosystems to maintain multiple functions and services simultaneously (multifunctionality). We aimed to do so by gathering data from ten ecosystem functions linked to the maintenance of primary production and nutrient cycling and storage (organic C, activity of β-glucosidase, pentoses, hexoses, total N, total available N, amino acids, proteins, available inorganic P, and phosphatase activity), and summarizing them in a multifunctionality index (M). We assessed how climate, species richness, anthropic factors (distance to the nearest town, sandy and asphalted road, and human population in the nearest town at several historical periods) and encroachment by sprouting shrubs impacted both the functions in isolation and M along a regional (ca. 350 km) gradient in Mediterranean grasslands and shrublands dominated by a non-sprouting shrub. Values of M were higher in those grasslands and shrublands containing sprouting shrubs (43 and 62%, respectively). A similar response was found when analyzing the different functions in isolation, as encroachment by sprouting shrubs increased functions by 2–80% compared to unencroached areas. Encroachment was the main driver of changes in M along the regional gradient evaluated, followed by anthropic factors and species richness. Climate had little effects on M in comparison to the other factors studied. Similar responses were observed when evaluating the functions in isolation. Overall, our results showed that M was higher at sites with higher sprouting shrub cover, longer distance to roads and higher perennial plant species richness. Our study is the first documenting that ecosystem multifunctionality in shrublands is enhanced by encroaching shrubs differing in size and leaf attributes. Our findings reinforce the idea that encroachment effects on ecosystem functioning cannot be generalized, and that are largely dependent on the traits of the encroaching shrub relative to those of the species being replaced.

Planning and Management of Mobility in Natural Protected Areas

The paper describes some relevant results of an on-going research aiming to elaborate a methodology to help the mobility management in natural parks, compatible with their protection missions: it has been developed a procedure to reproduce the mobility-environment relationships in various operational conditions. The final purpose is the identification of: a) the effects of various choices in transport planning, both at long term and strategic level; b) the most effective policies of mobility management. The work is articulated in the following steps: 1) definition of protected area on the basis of ecological and socio-economic criteria and legislative constraints; 2) analysis of mobility needs in the protected areas; 3) reconstruction of the state of the art of mobility management in natural parks at European level; 4) analysis of used traffic flows measurement methods; 5) analysis of environmental impacts due to transport systems modelling (air pollution and noise only); 6) identification of mitigation measures to be potentially applied. The whole methodology has been tested and validated on Italian case studies: i) the concerned area has been zoned according to the land-use peculiarities; ii) the local situations of transport infrastructure (roads and parking), services (public transport systems) and rules (traffic regulations) have been mapped with references to physical and functional attributes; iii) the mobility, both systematic and touristic, has been represented in an origin-destination matrix. By means of an assignment model the flows have been distributed and the corresponding average speeds to quantify gaseous and noise emissions was calculated, the criticalities in the reference scenario have been highlighted, as well as some alternative scenarios, including both operational and infrastructural measures have been identified. The comparison between projects and reference scenario allowed the quantification of effects (variation of emissions) for each scenario and a selection of the most effective management actions to be taken.

Planning and management of mobility in natural protected areas

The final purpose is the identification of: a) the effects of various choices in transport planning, both at long term and strategic level; b) the most effective policies of mobility management. The preliminary work was articulated in the following steps: 1) definition of protected area on the basis of ecological and socio-economic criteria and legislative constraints; 2) analysis of mobility needs in the protected areas; 3) reconstruction of the state of the art of mobility management in natural parks at European level; 4) analysis of used traffic flows measurement methods; 5) analysis of environmental impacts due to transport systems modelling (limited to air pollution and noise); 6) identification of mitigation measures to the potentially applied. The whole methodology has been firstly tested on the case study of the National Park of ?Gran Sasso and Monti della Laga? and further validated on the National Park of ?Gargano?, both located Italy: i) the concerned area has been zoned according to the land-use peculiarities; ii) the local situations of transport infrastructure (roads and parking), services (public transport systems) and rules (traffic regulations) have been mapped with references to physical and functional attributes; iii) the mobility, both systematic and touristic, has been synthetically represented in an origin-destination matrix. By means of an assignment model it has been determined the distribution of flows and the corresponding average speeds to quantify gaseous and noise emissions. On this basis the environmental criticalities in the reference scenario have been highlighted, as well as some alternative scenarios including both operational and infrastructural measures have been identified. The comparison between the projects and the reference scenario allowed the quantification of the effects (variation of emissions) for each scenario and a selection of the most effective management actions to be taken.

Evaluating the spatial and social equity effects of road pricing in the European urban context: the Madrid Metropolitan Area.

The paper explores the spatial and social impacts arising from implementation of a road-pricing scheme in the Madrid Metropolitan Area (MMA). Our analytical focus is on understanding the effects of the scheme on the transport accessibility of different social groups within the MMA. We define an evaluation framework to appraise the accessibility of different districts within the MMA in terms of the actual and perceived cost of using the road infrastructure "before" and "after" the implementation of the scheme. The framework was developed using quantitative survey data and qualitative data from focus group discussions with residents. We then simulated user behaviors (mode and route choice) based on the empirical evidence from a travel demand model for the MMA. The results from our simulation model demonstrated that implementation of the toll on the orbital metropolitan motorways (M40, M30, for example) decreases accessibility, mostly in the districts where there are no viable public transport alternatives. Our key finding is that the economic burden of the road-pricing scheme particularly affects unskilled and lower income individuals living in the south of the MMA. Consequently lower income people reduce their use of tolled roads and have to find new arrangements for these trips: i.e. switch to the public transport, spend double the time for their commuter trips or stay at home. The results of our research could be applicable more widely for anyone wishing to better understand the important relationship between increased transport cost and social equity, especially where there is an intention to introduce similar road-pricing schemes within the urban context.

Pantograph wear assesment in overhead conductor rail systems

Wear is the phenomenon that determines the lifetime of the collector strips. Since wear is an inevitable effect on pantograph-catenary systems, it is necessary to determine optimal operating conditions that can mitigate its effects. In this study we have performed a simulation model of the pantograph-overhead conductor rail system which allows the evaluation of the dynamic conditions of the system through the contact force. With these results we have made an evaluation of the quality of current collection, a calculation of the pantograph wear and a definition of the optimal operation conditions of the pantograph-overhead conductor rail system.

Simulation techniques for design of overhead conductor rail lines for speeds over 140 km/h

In overhead conductor rail lines, aluminium beams are usually mounted with support spacing between 8 and 12 meters, to limit the maximum vertical deflection in the center of the span. This small support spacing limits the use of overhead conductor rail to tunnels, therefore it has been used almost exclusively in metropolitan networks, with operation speeds below 110 km/h. Nevertheless, due to the lower cost of maintenance required for this electrification system, some railway administrations are beginning to install it in some tunnels on long-distance lines, requesting higher operation speeds [1]. Some examples are the Barcelona and Madrid suburban networks (Spain), and recent lines in Turkey and Malaysia. In order to adapt the design of the overhead conductor for higher speeds (V > 160 km/h), particular attention must be paid to the geometry of the conductor rail in critical zones as overlaps, crossings and, especially, transitions between conductor rail and conventional catenary, since the use of overhead conductor rail is limited to tunnels, as already mentioned. This paper describes simulation techniques developed in order to take into account these critical zones. Furthermore, some specific simulations results are presented that have been used to analyze and optimizes the geometry of this special zones to get a better current collection quality, in a real suburban network. This paper presents the work undertaken by the Railways Technology Research Centre (CITEF), having over 10 years of experience in railways research [1-4].

Air Mines. Urban Space Station

Air Mines The sky over the city's port was the color of a faulty screen, only partly lit up. As the silhouette of nearby buildings became darker, but more clearly visible against the fading blur-filter of a background, the realization came about how persistent a change had been taking place. Slowly, old wooden water reservoirs and rattling HVAC systems stopped being the only inhabitants of roofs. Slightly trembling, milkish jellyfish-translucent air volumes had joined the show in multiples. A few years ago artists and architects seized upon the death of buildings as their life-saving media. Equipped with constructive atlases and instruments they started disemboweling their subjects, poking about their systems, dumping out on the street the battered ugliness of their embarrassing bits and pieces, so rightly hidden by facades and height from everyday view. But, would you believe it? Even ?old ladies?, investment bankers or small children failed to get upset. Of course, old ladies are not what they used to be. It was old ladies themselves that made it happen after years of fights with the town hall, imaginative proposals and factual arguments. An industry with little financial gains but lots of welcome externalities was not, in fact, the ground for investment bankers. But they too had to admit that having otherwise stately buildings make fine particulate pencils with their facades was not the worse that could happen. Yes, making soot pencils had been found an interesting and visible end product of the endeavor, a sort of mining the air for vintage writing tools one can actually touch. The new view from the street did not seem as solid or dignified as that of old, and they hated that the market for Fine Particulates Extraction (FPE, read efpee) had to be applied on a matrix of blocks and streets that prevented undue concentration of the best or worse solutions. It had to be an evenly distributed city policy in order for the city to apply for cleaning casino money. Once the first prototypes had been deployed in buildings siding Garden Avenue or Bulwark Street even fast movers appreciated the sidekick of flower and plant smell dripping down the Urban Space Stations (USS, read use; USSs, read uses) as air and walls cooled off for a few hours after sunset. Enough. It was all nice to remember, but it was now time to go up and start the lightweight afternoon maintenance of their USS. Coop discussions had taken place all through the planning and continued through the construction phase as to how maintenance was going to be organized. Fasters had voted for a pro, pay a small amount and let them use it for rent and produce. In the end some neighbors decided they were slow enough to take care and it was now the turn. Regret came periodically, sometimes a week before, and lasted until work actually started. But lately it had been replaced by anxiety when it needed to be passed over to the next caretaker. It did not look their shift was good enough and couldn?t wait to fix it. Today small preparations needed to be made for a class visit next day from a nearby cook school. They were frequenters. It had not been easy, but it shouldn?t have been that hard. In the end, even the easiest things are hard if they involve a city, buildings and neighbors. On the face of the data, the technicalities and the way final designs had been worked out for adaptation to the different settings, the decision of where to go was self evident, but organization issues and the ever-growing politics of taste in a city of already-gentrified-rodents almost put the project in the frozen orbit of timeless beautiful future possibilities. This is how it was. A series of designs by XClinic and OSS had made it possible to adapt to different building structures, leave in most cases the roof untouched and adapted a new technology of flexing fiberglass tubes that dissipated wind pressure in smooth bending.......

Evaluating the equity effects of road-pricing in the European urban context - The Madrid Metropolitan Area

The paper identifies the potential spatial and social impacts of a proposed road-pricing scheme for different social groups in the Madrid Metropolitan Area (MMA). We appraise the accessibility of different districts within the MMA in terms of the actual and perceived cost of using the road infrastructure ‘before’ and ‘after’ implementation of the scheme. The appraisal framework was developed using quantitative survey data and qualitative focus group discussions with residents. We then simulated user behaviours (mode and route choice) based on the empirical evidence from a travel demand model for the MMA. The results from our simulation model demonstrated that implementation of the toll on the orbital metropolitan motorways (M40, M30, for example) decreases accessibility mostly in the districts where there are no viable public transport alternatives. Our specific study finding is that the economic burden of the road-pricing scheme particularly affects unskilled and lower income individuals living in the south of the MMA. The focus groups confirmed that low income drivers in the south part of the MMA would reduce their use of tolled roads and have to find new arrangements for these trips: i.e. switch to public transport, spend double the time travelling or stay at home. More generally, our research finds that European transport planners are still a long way from recognising the social equity implications of their policy decisions and that more thorough social appraisals are needed to avoid the social exclusion of low income populations when road tolling is proposed.

Desarrollo de conglomerados con la incorporación de cenizas volantes procedentes de la incineración de residuos sólidos urbanos

Esta tesis presenta los resultados de la investigación realizada sobre la inertización de cenizas volantes procedentes de residuos sólidos urbanos y su posterior encapsulación en distintas matrices de mortero. Durante el proceso de inertización, se ha logrado la inertización de éste residuo tóxico y peligroso (RTP) y también su valorización como subproducto. De esta forma se dispone de nueva “materia prima” a bajo coste y la eliminación de un residuo tóxico y peligroso con la consiguiente conservación de recursos naturales alternativos. La caracterización química de las cenizas analizadas refleja que éstas presentan altas concentraciones de cloruros, Zn y Pb. Durante la investigación se ha desarrollado un proceso de inertización de las cenizas volantes con bicarbonato sódico (NaHCO3) que reduce en un 99% el contenido en cloruros y mantiene el pH en valores óptimos para que la concentración de los metales pesados en el lixiviado sea mínima debido a su estabilización en forma de carbonatos insolubles. Se han elaborado morteros con cuatro tipos distintos de cementos (CEM-I, CEM-II, CAC y CSA) incorporando cenizas volantes inertizadas en una proporción igual a un 10% en peso del árido utilizado. Los morteros ensayados abarcan distintas dosificaciones tanto en la utilización de áridos con distintos diámetros (0/2 y 0/4), como en la relación cemento/árido (1/1 y 1/3). Se han obtenido las propiedades físicas y mecánicas de estos morteros mediante ensayos de Trabajabilidad, Estabilidad Dimensional, Carbonatación, Porosidad y Resistencias Mecánicas. De igual forma, se presentan resultados de ensayos de lixiviación de Zn, Pb, Cu y Cd, sobre probetas monolíticas de los morteros con los mejores comportamientos físico/mecánicos, donde se ha analizado el contenido en iones de dichos metales pesados lixiviados mediante determinación voltamperométrica de redisolución anódica Se concluye que todos los morteros ensayados son técnicamente aceptables, siendo los más favorables los elaborados con Cemento de Sulfoaluminato de Calcio (CSA) y con Cemento de Aluminato de Calcio (CAC). En este último caso, se mejoran las resistencias a compresión de los morteros de referencia en más de un 48%, y las resistencias a flexión en más de un 67%. De igual forma, los ensayos de lixiviado revelan la completa encapsulación de los iones de Zn y la mitigación en el lixiviado de los iones de Pb. Ambos morteros podrían ser perfectamente validos en actuaciones en las que se necesitase un producto de fraguado rápido, altas resistencias iniciales y compensación de las retracciones con una elevada estabilidad dimensional. En base a esto, el material podría ser utilizado como mortero de reparación en viales y pavimentos que requiriesen altas prestaciones, tales como: soleras industriales, pistas de aterrizaje, aparcamientos, etc. O bien, para la confección de elementos prefabricados sin armaduras estructurales, dada su elevada resistencia a flexión. ABSTRACT This dissertation presents the results of a research on inerting fly ash from urban solid waste and its subsequent encapsulation in mortar matrixes. The inerting of this hazardous toxic waste, as well as its valorization as a by-product has been achieved. In this way, a new "raw material" is available through a simple process and the toxic and hazardous waste is eliminated, and consequently, conservation of alternative natural resources is strengthened. Chemical analysis of the ashes analyzed shows high concentrations of soluble chlorides, Zn and Pb. An inerting process of fly ash with sodium bicarbonate (NaHCO3) has been developed which reduces 99% the content of chlorides and maintains pH at optimal values, so that the concentration of heavy metals in the leachate is minimum, due to its stabilization in the form of insoluble carbonates. Mortars with four different types of cements (CEM-I, CEM-II, CAC and CSA) have been developed by the addition of inertized fly ash in the form of carbonates, in the proportion of 10% in weight of the aggregates used. The samples tested include different proportions in the use of aggregates with different sizes (0/2 and 0/4), and in the cement/aggregate ratio (1/1 and 1/3). Physical/mechanical properties of these mortars have been studied through workability, dimensional stability, carbonation, porosity and mechanic strength tests. Leaching tests of Zn, Pb, Cu and Cd ions are also being performed on monolithic samples of the best behavioral mortars. The content in leachated heavy metal ions is being analyzed through stripping voltammetry determination. Conclusions drawn are that the tested CAC and CSA cement mortars present much better behavior than those of CEM-I and CEM-II cement. The results are especially remarkable for the CAC cement mortars, improving reference mortars compression strengths in more than 48%, and also bending strengths in more than 67%. Leaching tests confirm that the encapsulation of Zn and Pb is achieved and leachate of both ions is mitigated within the mortar matrixes. For the above stated reasons, it might be concluded that mortars made with calcium aluminate cements or calcium sulfoaluminate with the incorporation of treated fly ash, may be perfectly valid for uses in which a fast-curing product, with high initial strength and drying shrinkage compensation with a high dimensional stability is required. Based on this, the material could be used as repair mortar for structures, roads and industrial pavements requiring high performance, such as: industrial floorings, landing tracks, parking lots, etc. Alternatively, it could also be used in the manufacture of prefabricated elements without structural reinforcement, given its high bending strength.

Modelo para la integración del trazado de infraestructuras lineales en el paisaje y el medio ambiente basado en SIG

El análisis de las diferentes alternativas en la planificación y diseño de corredores y trazados de carreteras debe basarse en la correcta definición de variables territoriales que sirvan como criterios para la toma de decisión y esto requiere un análisis ambiental preliminar de esas variables de calidad. En España, los estudios de viabilidad de nuevas carreteras y autovías están asociados a una fase del proceso de decisión que se corresponde con el denominado Estudio Informativo, el cual establece condicionantes físicos, ambientales, de uso del suelo y culturales que deben ser considerados en las primeras fases de la definición del trazado de un corredor de carretera. Así, la metodología más frecuente es establecer diferentes niveles de capacidad de acogida del territorio en el área de estudio con el fin de resumir las variables territoriales en mapas temáticos y facilitar el proceso de trazado de las alternativas de corredores de carretera. El paisaje es un factor limitante a tener en cuenta en la planificación y diseño de carreteras y, por tanto, deben buscarse trazados más sostenibles en relación con criterios estéticos y ecológicos del mismo. Pero este factor no es frecuentemente analizado en los Estudios Informativos e incluso, si es considerado, los estudios específicos de la calidad del paisaje (estético y ecológico) y de las formas del terreno no incorporan las recomendaciones de las guías de trazado para evitar o reducir los impactos en el paisaje. Además, los mapas de paisaje que se generan en este tipo de estudios no se corresponden con la escala de desarrollo del Estudio Informativo (1:5.000). Otro déficit común en planificación de corredores y trazados de carreteras es que no se tiene en cuenta la conectividad del paisaje durante el proceso de diseño de la carretera para prevenir la afección a los corredores de fauna existentes en el paisaje. Este déficit puede originar un posterior efecto barrera en los movimientos dispersivos de la fauna y la fragmentación de sus hábitats debido a la ocupación parcial o total de las teselas de hábitats con importancia biológica para la fauna (o hábitats focales) y a la interrupción de los corredores de fauna que concentran esos movimientos dispersivos de la fauna entre teselas. El objetivo principal de esta tesis es mejorar el estudio del paisaje para prevenir su afección durante el proceso de trazado de carreteras, facilitar la conservación de los corredores de fauna (o pasillos verdes) y la localización de medidas preventivas y correctoras en términos de selección y cuantificación de factores de idoneidad a fin de reducir los impactos visuales y ecológicos en el paisaje a escala local. Concretamente, la incorporación de valores cuantitativos y bien justificados en el proceso de decisión permite incrementar la transparencia en el proceso de diseño de corredores y trazados de carreteras. Con este fin, se han planteado cuatro preguntas específicas en esta investigación (1) ¿Cómo se seleccionan y evalúan los factores territoriales limitantes para localizar una nueva carretera por los profesionales españoles de planificación del territorio en relación con el paisaje? (2) ¿Cómo pueden ser definidos los corredores de fauna a partir de factores del paisaje que influyen en los movimientos dispersivos de la fauna? (3) ¿Cómo pueden delimitarse y evaluarse los corredores de fauna incluyendo el comportamiento parcialmente errático en los movimientos dispersivos de la fauna y el efecto barrera de los elementos antrópicos a una escala local? (4) ¿Qué y cómo las recomendaciones de diseño de carreteras relacionadas con el paisaje y las formas del terreno pueden ser incluidas en un modelo de Sistemas de Información Geográfica (SIG) para ayudar a los ingenieros civiles durante el proceso de diseño de un trazado de carreteras bajo el punto de vista de la sostenibilidad?. Esta tesis doctoral propone nuevas metodologías que mejoran el análisis visual y ecológico del paisaje utilizando indicadores y modelos SIG para obtener alternativas de trazado que produzcan un menor impacto en el paisaje. Estas metodologías fueron probadas en un paisaje heterogéneo con una alta tasa de densidad de corzo (Capreolus capreolus L.), uno de los grandes mamíferos más atropellados en la red de carreteras españolas, y donde está planificada la construcción de una nueva autovía que atravesará la mitad del área de distribución del corzo. Inicialmente, se han analizado las variables utilizadas en 22 estudios de proyectos de planificación de corredores de carreteras promovidos por el Ministerio de Fomento entre 2006 y 2008. Estas variables se agruparon según condicionantes físicos, ambientales, de usos del suelo y culturales con el fin de comparar los valores asignados de capacidad de acogida del territorio a cada variable en los diferentes estudios revisados. Posteriormente, y como etapa previa de un análisis de conectividad, se construyó un mapa de resistencia de los movimientos dispersivos del corzo en base a la literatura y al juicio de expertos. Usando esta investigación como base, se le asignó un valor de resistencia a cada factor seleccionado para construir la matriz de resistencia, ponderándolo y combinándolo con el resto de factores usando el proceso analítico jerárquico y los operadores de lógica difusa como métodos de análisis multicriterio. Posteriormente, se diseñó una metodología SIG para delimitar claramente la extensión física de los corredores de fauna de acuerdo a un valor umbral de ancho geométrico mínimo, así como la existencia de múltiples potenciales conexiones entre cada par de teselas de hábitats presentes en el paisaje estudiado. Finalmente, se realizó un procesado de datos Light Detection and Ranging (LiDAR) y un modelo SIG para calcular la calidad del paisaje (estético y ecológico), las formas del terreno que presentan características similares para trazar una carretera y la acumulación de vistas de potenciales conductores y observadores de los alrededores de la nueva vía. Las principales contribuciones de esta investigación al conocimiento científico existente en el campo de la evaluación del impacto ambiental en relación al diseño de corredores y trazados de carreteras son cuatro. Primero, el análisis realizado de 22 Estudios Informativos de planificación de carreteras reveló que los métodos aplicados por los profesionales para la evaluación de la capacidad de acogida del territorio no fue suficientemente estandarizada, ya que había una falta de uniformidad en el uso de fuentes cartográficas y en las metodologías de evaluación de la capacidad de acogida del territorio, especialmente en el análisis de la calidad del paisaje estético y ecológico. Segundo, el análisis realizado en esta tesis destaca la importancia de los métodos multicriterio para estructurar, combinar y validar factores que limitan los movimientos dispersivos de la fauna en el análisis de conectividad. Tercero, los modelos SIG desarrollados Generador de alternativas de corredores o Generator of Alternative Corridors (GAC) y Eliminador de Corredores Estrechos o Narrow Corridor Eraser (NCE) pueden ser aplicados sistemáticamente y sobre una base científica en análisis de conectividad como una mejora de las herramientas existentes para la comprensión el paisaje como una red compuesta por nodos y enlaces interconectados. Así, ejecutando los modelos GAC y NCE de forma iterativa, pueden obtenerse corredores alternativos con similar probabilidad de ser utilizados por la fauna y sin que éstos presenten cuellos de botella. Cuarto, el caso de estudio llevado a cabo de prediseño de corredores y trazado de una nueva autovía ha sido novedoso incluyendo una clasificación semisupervisada de las formas del terreno, filtrando una nube de puntos LiDAR e incluyendo la nueva geometría 3D de la carretera en el Modelo Digital de Superficie (MDS). El uso combinado del procesamiento de datos LiDAR y de índices y clasificaciones geomorfológicas puede ayudar a los responsables encargados en la toma de decisiones a evaluar qué alternativas de trazado causan el menor impacto en el paisaje, proporciona una visión global de los juicios de valor más aplicados y, en conclusión, define qué medidas de integración paisajística correctoras deben aplicarse y dónde. ABSTRACT The assessment of different alternatives in road-corridor planning and layout design must be based on a number of well-defined territorial variables that serve as decision-making criteria, and this requires a high-quality preliminary environmental analysis of those quality variables. In Spain, feasibility studies for new roads and motorways are associated to a phase of the decision procedure which corresponds with the one known as the Informative Study, which establishes the physical, environmental, land-use and cultural constraints to be considered in the early stages of defining road corridor layouts. The most common methodology is to establish different levels of Territorial Carrying Capacity (TCC) in the study area in order to summarize the territorial variables on thematic maps and facilitate the tracing process of road-corridor layout alternatives. Landscape is a constraint factor that must be considered in road planning and design, and the most sustainable layouts should be sought based on aesthetic and ecological criteria. However this factor is not often analyzed in Informative Studies and even if it is, baseline studies on landscape quality (aesthetic and ecological) and landforms do not usually include the recommendations of road tracing guides designed to avoid or reduce impacts on the landscape. The resolution of the landscape maps produced in this type of studies does not comply with the recommended road design scale (1:5,000) in the regulations for the Informative Study procedure. Another common shortcoming in road planning is that landscape ecological connectivity is not considered during road design in order to avoid affecting wildlife corridors in the landscape. In the prior road planning stage, this issue could lead to a major barrier effect for fauna dispersal movements and to the fragmentation of their habitat due to the partial or total occupation of habitat patches of biological importance for the fauna (or focal habitats), and the interruption of wildlife corridors that concentrate fauna dispersal movements between patches. The main goal of this dissertation is to improve the study of the landscape and prevent negative effects during the road tracing process, and facilitate the preservation of wildlife corridors (or green ways) and the location of preventive and corrective measures by selecting and quantifying suitability factors to reduce visual and ecological landscape impacts at a local scale. Specifically the incorporation of quantitative and well-supported values in the decision-making process provides increased transparency in the road corridors and layouts design process. Four specific questions were raised in this research: (1) How are territorial constraints selected and evaluated in terms of landscape by Spanish land-planning practitioners before locating a new road? (2) How can wildlife corridors be defined based on the landscape factors influencing the dispersal movements of fauna? (3) How can wildlife corridors be delimited and assessed to include the partially erratic movements of fauna and the barrier effect of the anthropic elements at a local scale? (4) How recommendations of road design related to landscape and landforms can be included in a Geographic Information System (GIS) model to aid civil engineers during the road layout design process and support sustainable development? This doctoral thesis proposes new methodologies that improve the assessment of the visual and ecological landscape character using indicators and GIS models to obtain road layout alternatives with a lower impact on the landscape. These methodologies were tested on a case study of a heterogeneous landscape with a high density of roe deer (Capreolus capreolus L.) –one of the large mammals most commonly hit by vehicles on the Spanish road network– and where a new motorway is planned to pass through the middle of their distribution area. We explored the variables used in 22 road-corridor planning projects sponsored by the Ministry of Public Works between 2006 and 2008. These variables were grouped into physical, environmental, land-use and cultural constraints for the purpose of comparing the TCC values assigned to each variable in the various studies reviewed. As a prior stage in a connectivity analysis, a map of resistance to roe deer dispersal movements was created based on the literature and experts judgment. Using this research as a base, each factor selected to build the matrix was assigned a resistance value and weighted and combined with the rest of the factors using the analytic hierarchy process (AHP) and fuzzy logic operators as multicriteria assessment (MCA) methods. A GIS methodology was designed to clearly delimit the physical area of wildlife corridors according to a geometric threshold width value, and the multiple potential connections between each pair of habitat patches in the landscape. A Digital Surface Model Light Detection and Ranging (LiDAR) dataset processing and a GIS model was performed to determine landscape quality (aesthetic and ecological) and landforms with similar characteristics for the road layout, and the cumulative viewshed of potential drivers and observers in the area surrounding the new motorway. The main contributions of this research to current scientific knowledge in the field of environmental impact assessment for road corridors and layouts design are four. First, the analysis of 22 Informative Studies on road planning revealed that the methods applied by practitioners for assessing the TCC were not sufficiently standardized due to the lack of uniformity in the cartographic information sources and the TCC valuation methodologies, especially in the analysis of the aesthetic and ecological quality of the landscape. Second, the analysis in this dissertation highlights the importance of multicriteria methods to structure, combine and validate factors that constrain wildlife dispersal movements in the connectivity analysis. Third, the “Generator of Alternative Corridors (GAC)” and “Narrow Corridor Eraser (NCE)” GIS models developed can be applied systematically and on a scientific basis in connectivity analyses to improve existing tools and understand landscape as a network composed of interconnected nodes and links. Thus, alternative corridors with similar probability of use by fauna and without bottlenecks can be obtained by iteratively running GAC and NCE models. Fourth, our case study of new motorway corridors and layouts design innovatively included semi-supervised classification of landforms, filtering of LiDAR point clouds and new 3D road geometry on the Digital Surface Model (DSM). The combined used of LiDAR data processing and geomorphological indices and classifications can help decision-makers assess which road layouts produce lower impacts on the landscape, provide an overall insight into the most commonly applied value judgments, and in conclusion, define which corrective measures should be applied in terms of landscaping, and where.

Modelos de asociación público-privada en la provisión de infraestructura: la experiencia internacional y el desarrollo de las autopistas en México

Análisis de los modelos de asociación público-privado utilizados en la construcción de autopistas en México en los últimos 25 años. Existen estudios que respaldan la opinión de que los niveles de competitividad están estrechamente relacionados con el desarrollo de la infraestructura de los países. La baja competitividad de México debido a la mala calidad de su infraestructura, pone en evidencia la necesidad del mejoramiento y provisión de la misma en un marco de escasez de recursos fiscales. Esta argumentación, sustenta la intervención del sector privado para apoyar el financiamiento de infraestructura mediante nuevos mecanismos de asociación público privada (APP). En el artículo se describen: el desarrollo de la infraestructura carretera de México, la forma en que ésta fue financiada en el pasado con modelos de concesión para la construcción de carreteras de alta calidad y los modelos de APP que el país está utilizando para atraer la inversión privada en el actual programa mexicano de autopistas. Se muestran los beneficios del empleo de estos esquemas de financiamiento y se ofrece una serie de recomendaciones para transparentar el uso de estos modelos. There are studies that support the view that the competitiveness levels are closely related to the development of the country’s infrastructure. The low competitiveness of Mexico due to the poor quality of its infrastructure, underscores the need for improvement and provision of the same in a context of scarce fiscal resources. This argument supports the intervention of the private sector to finance infrastructure through new mechanisms for public private partnership (PPP). The article describes the development of the Mexico road infrastructure, the way in which it was funded in the past by models of concession for the construction of high-quality roads and models of app that the country is using to attract private investment in the current Mexican highways program. The benefits of these funding schemes are displayed and recommendations are offered for transparent use of these models