Modelling and Control of Stepper Motors for High Accuracy Positioning Systems Used in Radioactive Environments

Hybrid Stepper Motors are widely used in open-loop position applications. They are the choice of actuation for the collimators in the Large Hadron Collider, the largest particle accelerator at CERN. In this case the positioning requirements and the highly radioactive operating environment are unique. The latter forces both the use of long cables to connect the motors to the drives which act as transmission lines and also prevents the use of standard position sensors. However, reliable and precise operation of the collimators is critical for the machine, requiring the prevention of step loss in the motors and maintenance to be foreseen in case of mechanical degradation. In order to make the above possible, an approach is proposed for the application of an Extended Kalman Filter to a sensorless stepper motor drive, when the motor is separated from its drive by long cables. When the long cables and high frequency pulse width modulated control voltage signals are used together, the electrical signals difer greatly between the motor and drive-side of the cable. Since in the considered case only drive-side data is available, it is therefore necessary to estimate the motor-side signals. Modelling the entire cable and motor system in an Extended Kalman Filter is too computationally intensive for standard embedded real-time platforms. It is, in consequence, proposed to divide the problem into an Extended Kalman Filter, based only on the motor model, and separated motor-side signal estimators, the combination of which is less demanding computationally. The efectiveness of this approach is shown in simulation. Then its validity is experimentally demonstrated via implementation in a DSP based drive. A testbench to test its performance when driving an axis of a Large Hadron Collider collimator is presented along with the results achieved. It is shown that the proposed method is capable of achieving position and load torque estimates which allow step loss to be detected and mechanical degradation to be evaluated without the need for physical sensors. These estimation algorithms often require a precise model of the motor, but the standard electrical model used for hybrid stepper motors is limited when currents, which are high enough to produce saturation of the magnetic circuit, are present. New model extensions are proposed in order to have a more precise model of the motor independently of the current level, whilst maintaining a low computational cost. It is shown that a significant improvement in the model It is achieved with these extensions, and their computational performance is compared to study the cost of model improvement versus computation cost. The applicability of the proposed model extensions is demonstrated via their use in an Extended Kalman Filter running in real-time for closed-loop current control and mechanical state estimation. An additional problem arises from the use of stepper motors. The mechanics of the collimators can wear due to the abrupt motion and torque profiles that are applied by them when used in the standard way, i.e. stepping in open-loop. Closed-loop position control, more specifically Field Oriented Control, would allow smoother profiles, more respectful to the mechanics, to be applied but requires position feedback. As mentioned already, the use of sensors in radioactive environments is very limited for reliability reasons. Sensorless control is a known option but when the speed is very low or zero, as is the case most of the time for the motors used in the LHC collimator, the loss of observability prevents its use. In order to allow the use of position sensors without reducing the long term reliability of the whole system, the possibility to switch from closed to open loop is proposed and validated, allowing the use of closed-loop control when the position sensors function correctly and open-loop when there is a sensor failure. A different approach to deal with the switched drive working with long cables is also presented. Switched mode stepper motor drives tend to have poor performance or even fail completely when the motor is fed through a long cable due to the high oscillations in the drive-side current. The design of a stepper motor output fillter which solves this problem is thus proposed. A two stage filter, one devoted to dealing with the diferential mode and the other with the common mode, is designed and validated experimentally. With this ?lter the drive performance is greatly improved, achieving a positioning repeatability even better than with the drive working without a long cable, the radiated emissions are reduced and the overvoltages at the motor terminals are eliminated.

Self-reference Scrubber for TMR Systems Based on Xilinx Virtex FPGAs

SRAM-based FPGAs are sensitive to radiation effects. Soft errors can appear and accumulate, potentially defeating mitigation strategies deployed at the Application Layer. Therefore, Configuration Memory scrubbing is required to improve radiation tolerance of such FPGAs in space applications. Virtex FPGAs allow runtime scrubbing by means of dynamic partial reconfiguration. Even with scrubbing, intra-FPGA TMR systems are subjected to common-mode errors affecting more than one design domain. This is solved in inter-FPGA TMR systems at the expense of a higher cost, power and mass. In this context, a self-reference scrubber for device-level TMR system based on Xilinx Virtex FPGAs is presented. This scrubber allows for a fast SEU/MBU detection and correction by peer frame comparison without needing to access a golden configuration memory

Geochemistry and risk assessment of street dust in Luanda, Angola, a tropical urban environment

A total of 92 samples of street dust were collected in Luanda, Angola, were sieved below 100 μm, and analysed by ICP-MS for 35 elements after an aqua-regia digestion. The concentration and spatial heterogeneity of trace elements in the street dust of Luanda are generally lower than in most industrialized cities in the Northern hemisphere. These observations reveal a predominantly “natural” origin for the street dust in Luanda, which is also manifested in that some geochemical processes that occur in natural soils are preserved in street dust: the separation of uranium from thorium, and the retention of the former by carbonate materials, or the high correlation between arsenic and vanadium due to their common mode of adsorption on solid particles in the form of oxyanions. The only distinct anthropogenic fingerprint in the composition of Luanda's street dust is the association Pb–Cd–Sb–Cu (and to a lesser extent, Ba–Cr–Zn). The use of risk assessment strategies has proved helpful in identifying the routes of exposure to street dust and the trace elements therein of most concern in terms of potential adverse health effects. In Luanda the highest levels of risk seem to be associated (a) with the presence of As and Pb in the street dust and (b) with the route of ingestion of dust particles, for all the elements included in the study except Hg, for which inhalation of vapours presents a slightly higher risk than ingestion. However, given the large uncertainties associated with the estimates of toxicity values and exposure factors, and the absence of site-specific biometric factors, these results should be regarded as preliminary and further research should be undertaken before any definite conclusions regarding potential health effects are drawn.

Wide bandwidth envelope trackers with reduced switching frequency for RF power amplifier

El requerimiento de proveer alta frecuencia de datos en los modernos sistema de comunicación inalámbricos resulta en complejas señales moduladas de radio-frequencia (RF) con un gran ancho de banda y alto ratio pico-promedio (PAPR). Para garantizar la linealidad del comportamiento, los amplificadores lineales de potencia comunes funcionan típicamente entre 4 y 10 dB de back-o_ desde la máxima potencia de salida, ocasionando una baja eficiencia del sistema. La eliminación y restauración de la evolvente (EER) y el seguimiento de la evolvente (ET) son dos prometedoras técnicas para resolver el problema de la eficiencia. Tanto en EER como en ET, es complicado diseñar un amplificador de potencia que sea eficiente para señales de RF de alto ancho de banda y alto PAPR. Una propuesta común para los amplificadores de potencia es incluir un convertidor de potencia de muy alta eficiencia operando a frecuencias más altas que el ancho de banda de la señal RF. En este caso, la potencia perdida del convertidor ocasionado por la alta frecuencia desaconseja su práctica cuando el ancho de banda es muy alto. La solución a este problema es el enfoque de esta disertación que presenta dos arquitecturas de amplificador evolvente: convertidor híbrido-serie con una técnica de evolvente lenta y un convertidor multinivel basado en un convertidor reductor multifase con control de tiempo mínimo. En la primera arquitectura, una topología híbrida está compuesta de una convertidor reductor conmutado y un regulador lineal en serie que trabajan juntos para ajustar la tensión de salida para seguir a la evolvente con precisión. Un algoritmo de generación de una evolvente lenta crea una forma de onda con una pendiente limitada que es menor que la pendiente máxima de la evolvente original. La salida del convertidor reductor sigue esa forma de onda en vez de la evolvente original usando una menor frecuencia de conmutación, porque la forma de onda no sólo tiene una pendiente reducida sino también un menor ancho de banda. De esta forma, el regulador lineal se usa para filtrar la forma de onda tiene una pérdida de potencia adicional. Dependiendo de cuánto se puede reducir la pendiente de la evolvente para producir la forma de onda, existe un trade-off entre la pérdida de potencia del convertidor reductor relacionada con la frecuencia de conmutación y el regulador lineal. El punto óptimo referido a la menor pérdida de potencia total del amplificador de evolvente es capaz de identificarse con la ayuda de modelo preciso de pérdidas que es una combinación de modelos comportamentales y analíticos de pérdidas. Además, se analiza el efecto en la respuesta del filtro de salida del convertidor reductor. Un filtro de dampeo paralelo extra es necesario para eliminar la oscilación resonante del filtro de salida porque el convertidor reductor opera en lazo abierto. La segunda arquitectura es un amplificador de evolvente de seguimiento de tensión multinivel. Al contrario que los convertidores que usan multi-fuentes, un convertidor reductor multifase se emplea para generar la tensión multinivel. En régimen permanente, el convertidor reductor opera en puntos del ciclo de trabajo con cancelación completa del rizado. El número de niveles de tensión es igual al número de fases de acuerdo a las características del entrelazamiento del convertidor reductor. En la transición, un control de tiempo mínimo (MTC) para convertidores multifase es novedosamente propuesto y desarrollado para cambiar la tensión de salida del convertidor reductor entre diferentes niveles. A diferencia de controles convencionales de tiempo mínimo para convertidores multifase con inductancia equivalente, el propuesto MTC considera el rizado de corriente por cada fase basado en un desfase fijo que resulta en diferentes esquemas de control entre las fases. La ventaja de este control es que todas las corrientes vuelven a su fase en régimen permanente después de la transición para que la siguiente transición pueda empezar muy pronto, lo que es muy favorable para la aplicación de seguimiento de tensión multinivel. Además, el control es independiente de la carga y no es afectado por corrientes de fase desbalanceadas. Al igual que en la primera arquitectura, hay una etapa lineal con la misma función, conectada en serie con el convertidor reductor multifase. Dado que tanto el régimen permanente como el estado de transición del convertidor no están fuertemente relacionados con la frecuencia de conmutación, la frecuencia de conmutación puede ser reducida para el alto ancho de banda de la evolvente, la cual es la principal consideración de esta arquitectura. La optimización de la segunda arquitectura para más alto anchos de banda de la evolvente es presentada incluyendo el diseño del filtro de salida, la frecuencia de conmutación y el número de fases. El área de diseño del filtro está restringido por la transición rápida y el mínimo pulso del hardware. La rápida transición necesita un filtro pequeño pero la limitación del pulso mínimo del hardware lleva el diseño en el sentido contrario. La frecuencia de conmutación del convertidor afecta principalmente a la limitación del mínimo pulso y a las pérdidas de potencia. Con una menor frecuencia de conmutación, el ancho de pulso en la transición es más pequeño. El número de fases relativo a la aplicación específica puede ser optimizado en términos de la eficiencia global. Otro aspecto de la optimización es mejorar la estrategia de control. La transición permite seguir algunas partes de la evolvente que son más rápidas de lo que el hardware puede soportar al precio de complejidad. El nuevo método de sincronización de la transición incrementa la frecuencia de la transición, permitiendo que la tensión multinivel esté más cerca de la evolvente. Ambas estrategias permiten que el convertidor pueda seguir una evolvente con un ancho de banda más alto que la limitación de la etapa de potencia. El modelo de pérdidas del amplificador de evolvente se ha detallado y validado mediante medidas. El mecanismo de pérdidas de potencia del convertidor reductor tiene que incluir las transiciones en tiempo real, lo cual es diferente del clásico modelos de pérdidas de un convertidor reductor síncrono. Este modelo estima la eficiencia del sistema y juega un papel muy importante en el proceso de optimización. Finalmente, la segunda arquitectura del amplificador de evolvente se integra con el amplificador de clase F. La medida del sistema EER prueba el ahorro de energía con el amplificador de evolvente propuesto sin perjudicar la linealidad del sistema. ABSTRACT The requirement of delivering high data rates in modern wireless communication systems results in complex modulated RF signals with wide bandwidth and high peak-to-average ratio (PAPR). In order to guarantee the linearity performance, the conventional linear power amplifiers typically work at 4 to 10 dB back-off from the maximum output power, leading to low system efficiency. The envelope elimination and restoration (EER) and envelope tracking (ET) are two promising techniques to overcome the efficiency problem. In both EER and ET, it is challenging to design efficient envelope amplifier for wide bandwidth and high PAPR RF signals. An usual approach for envelope amplifier includes a high-efficiency switching power converter operating at a frequency higher than the RF signal's bandwidth. In this case, the power loss of converter caused by high switching operation becomes unbearable for system efficiency when signal bandwidth is very wide. The solution of this problem is the focus of this dissertation that presents two architectures of envelope amplifier: a hybrid series converter with slow-envelope technique and a multilevel converter based on a multiphase buck converter with the minimum time control. In the first architecture, a hybrid topology is composed of a switched buck converter and a linear regulator in series that work together to adjust the output voltage to track the envelope with accuracy. A slow envelope generation algorithm yields a waveform with limited slew rate that is lower than the maximum slew rate of the original envelope. The buck converter's output follows this waveform instead of the original envelope using lower switching frequency, because the waveform has not only reduced slew rate but also reduced bandwidth. In this way, the linear regulator used to filter the waveform has additional power loss. Depending on how much reduction of the slew rate of envelope in order to obtain that waveform, there is a trade-off between the power loss of buck converter related to the switching frequency and the power loss of linear regulator. The optimal point referring to the lowest total power loss of this envelope amplifier is identified with the help of a precise power loss model that is a combination of behavioral and analytic loss model. In addition, the output filter's effect on the response is analyzed. An extra parallel damping filter is needed to eliminate the resonant oscillation of output filter L and C, because the buck converter operates in open loop. The second architecture is a multilevel voltage tracking envelope amplifier. Unlike the converters using multi-sources, a multiphase buck converter is employed to generate the multilevel voltage. In the steady state, the buck converter operates at complete ripple cancellation points of duty cycle. The number of the voltage levels is equal to the number of phases according the characteristics of interleaved buck converter. In the transition, a minimum time control (MTC) for multiphase converter is originally proposed and developed for changing the output voltage of buck converter between different levels. As opposed to conventional minimum time control for multiphase converter with equivalent inductance, the proposed MTC considers the current ripple of each phase based on the fixed phase shift resulting in different control schemes among the phases. The advantage of this control is that all the phase current return to the steady state after the transition so that the next transition can be triggered very soon, which is very favorable for the application of multilevel voltage tracking. Besides, the control is independent on the load condition and not affected by the unbalance of phase current. Like the first architecture, there is also a linear stage with the same function, connected in series with the multiphase buck converter. Since both steady state and transition state of the converter are not strongly related to the switching frequency, it can be reduced for wide bandwidth envelope which is the main consideration of this architecture. The optimization of the second architecture for wider bandwidth envelope is presented including the output filter design, switching frequency and the number of phases. The filter design area is restrained by fast transition and the minimum pulse of hardware. The fast transition needs small filter but the minimum pulse of hardware limitation pushes the filter in opposite way. The converter switching frequency mainly affects the minimum pulse limitation and the power loss. With lower switching frequency, the pulse width in the transition is smaller. The number of phases related to specific application can be optimized in terms of overall efficiency. Another aspect of optimization is improving control strategy. Transition shift allows tracking some parts of envelope that are faster than the hardware can support at the price of complexity. The new transition synchronization method increases the frequency of transition, allowing the multilevel voltage to be closer to the envelope. Both control strategies push the converter to track wider bandwidth envelope than the limitation of power stage. The power loss model of envelope amplifier is detailed and validated by measurements. The power loss mechanism of buck converter has to include the transitions in real time operation, which is different from classical power loss model of synchronous buck converter. This model estimates the system efficiency and play a very important role in optimization process. Finally, the second envelope amplifier architecture is integrated with a Class F amplifier. EER system measurement proves the power saving with the proposed envelope amplifier without disrupting the linearity performance.

Evaluation of the PV cell operation temperature in the process of fast switching to open-circuit mode

A procedure for measuring the overheating temperature (ΔT ) of a p-n junction area in the structure of photovoltaic (PV) cells converting laser or solar radiations relative to the ambient temperature has been proposed for the conditions of connecting to an electric load. The basis of the procedure is the measurement of the open-circuit voltage (VO C ) during the initial time period after the fast disconnection of the external resistive load. The simultaneous temperature control on an external heated part of a PV module gives the means for determining the value of VO C at ambient temperature. Comparing it with that measured after switching OFF the load makes the calculation of ΔT possible. Calibration data on the VO C = f(T ) dependences for single-junction AlGaAs/GaAs and triple-junction InGaP/GaAs/Ge PV cells are presented. The temperature dynamics in the PV cells has been determined under flash illumination and during fast commutation of the load. Temperature measurements were taken in two cases: converting continuous laser power by single-junction cells and converting solar power by triple-junction cells operating in the concentrator modules.

Reduced order models for industrial thermo-fluid problems

A new method is presented to generate reduced order models (ROMs) in Fluid Dynamics problems of industrial interest. The method is based on the expansion of the flow variables in a Proper Orthogonal Decomposition (POD) basis, calculated from a limited number of snapshots, which are obtained via Computational Fluid Dynamics (CFD). Then, the POD-mode amplitudes are calculated as minimizers of a properly defined overall residual of the equations and boundary conditions. The method includes various ingredients that are new in this field. The residual can be calculated using only a limited number of points in the flow field, which can be scattered either all over the whole computational domain or over a smaller projection window. The resulting ROM is both computationally efficient(reconstructed flow fields require, in cases that do not present shock waves, less than 1 % of the time needed to compute a full CFD solution) and flexible(the projection window can avoid regions of large localized CFD errors).Also, for problems related with aerodynamics, POD modes are obtained from a set of snapshots calculated by a CFD method based on the compressible Navier Stokes equations and a turbulence model (which further more includes some unphysical stabilizing terms that are included for purely numerical reasons), but projection onto the POD manifold is made using the inviscid Euler equations, which makes the method independent of the CFD scheme. In addition, shock waves are treated specifically in the POD description, to avoid the need of using a too large number of snapshots. Various definitions of the residual are also discussed, along with the number and distribution of snapshots, the number of retained modes, and the effect of CFD errors. The method is checked and discussed on several test problems that describe (i) heat transfer in the recirculation region downstream of a backwards facing step, (ii) the flow past a two-dimensional airfoil in both the subsonic and transonic regimes, and (iii) the flow past a three-dimensional horizontal tail plane. The method is both efficient and numerically robust in the sense that the computational effort is quite small compared to CFD and results are both reasonably accurate and largely insensitive to the definition of the residual, to CFD errors, and to the CFD method itself, which may contain artificial stabilizing terms. Thus, the method is amenable for practical engineering applications. Resumen Se presenta un nuevo método para generar modelos de orden reducido (ROMs) aplicado a problemas fluidodinámicos de interés industrial. El nuevo método se basa en la expansión de las variables fluidas en una base POD, calculada a partir de un cierto número de snapshots, los cuales se han obtenido gracias a simulaciones numéricas (CFD). A continuación, las amplitudes de los modos POD se calculan minimizando un residual global adecuadamente definido que combina las ecuaciones y las condiciones de contorno. El método incluye varios ingredientes que son nuevos en este campo de estudio. El residual puede calcularse utilizando únicamente un número limitado de puntos del campo fluido. Estos puntos puede encontrarse dispersos a lo largo del dominio computacional completo o sobre una ventana de proyección. El modelo ROM obtenido es tanto computacionalmente eficiente (en aquellos casos que no presentan ondas de choque reconstruir los campos fluidos requiere menos del 1% del tiempo necesario para calcular una solución CFD) como flexible (la ventana de proyección puede escogerse de forma que evite contener regiones con errores en la solución CFD localizados y grandes). Además, en problemas aerodinámicos, los modos POD se obtienen de un conjunto de snapshots calculados utilizando un código CFD basado en la versión compresible de las ecuaciones de Navier Stokes y un modelo de turbulencia (el cual puede incluir algunos términos estabilizadores sin sentido físico que se añaden por razones puramente numéricas), aunque la proyección en la variedad POD se hace utilizando las ecuaciones de Euler, lo que hace al método independiente del esquema utilizado en el código CFD. Además, las ondas de choque se tratan específicamente en la descripción POD para evitar la necesidad de utilizar un número demasiado grande de snapshots. Varias definiciones del residual se discuten, así como el número y distribución de los snapshots,el número de modos retenidos y el efecto de los errores debidos al CFD. El método se comprueba y discute para varios problemas de evaluación que describen (i) la transferencia de calor en la región de recirculación aguas abajo de un escalón, (ii) el flujo alrededor de un perfil bidimensional en regímenes subsónico y transónico y (iii) el flujo alrededor de un estabilizador horizontal tridimensional. El método es tanto eficiente como numéricamente robusto en el sentido de que el esfuerzo computacional es muy pequeño comparado con el requerido por el CFD y los resultados son razonablemente precisos y muy insensibles a la definición del residual, los errores debidos al CFD y al método CFD en sí mismo, el cual puede contener términos estabilizadores artificiales. Por lo tanto, el método puede utilizarse en aplicaciones prácticas de ingeniería.

Numerical analysis of mixe-mode fracture of brickwork masonry with embedded discontinuity elements

One of the common pathologies of brickwork masonry structural elements and walls is the cracking associated with the differential settlements and/or excessive deflections of the slabs along the life of the structure. The scarce capacity of the masonry in order to accompany the structural elements that surround it, such as floors, beams or foundations, in their movements makes the brickwork masonry to be an element that frequently presents this kind of problem. This problem is a fracture problem, where the wall is cracked under mixed mode fracture: tensile and shear stresses combination, under static loading. Consequently, it is necessary to advance in the simulation and prediction of brickwork masonry mechanical behaviour under tensile and shear loading. The quasi-brittle behaviour of the brickwork masonry can be studied using the cohesive crack model whose application to other quasibrittle materials like concrete has traditionally provided very satisfactory results.

A common mechanism of defective channel trafficking underlying DFNA2 hearing loss result in different cell surface expression levels of KCNQ4 mutants

KCNQ4 mutations underlie DFNA2, a subtype of autosomal dominant hearing loss. We had previously identified the pore-region p.G296S mutation that impaired channel activity in two manners: it greatly reduced surface expression and abolished channel function. Moreover, G296S mutant exerted a strong dominant-negative effect on potassium currents by reducing the channel expression at the cell surface representing the first study to identify a trafficking-dependent dominant mechanism for the loss of KCNQ4 channel function in DFNA2. Here, we have investigated the pathogenic mechanism associated with all the described KCNQ4 mutations (F182L, W242X, E260K, D262V, L274H, W276S, L281S, G285C, G285S and G321S) that are located in different domains of the channel protein. F182L mutant showed a wild type-like cell-surface distribution in transiently transfected NIH3T3 fibroblasts and the recorded currents in Xenopus oocytes resembled those of the wild-type. The remaining KCNQ4 mutants abolished potassium currents, but displayed distinct levels of defective cell-surface expression in NIH3T3 as quantified by flow citometry. Co-localization studies revealed these mutants were retained in the ER, unless W242X, which showed a clear co-localization with Golgi apparatus. Interestingly, this mutation results in a truncated KCNQ4 protein at the S5 transmembrane domain, before the pore region, that escapes the protein quality control in the ER but does not reach the cell surface at normal levels. Currently we are investigating the trafficking behaviour and electrophysiological properties of several KCNQ4 truncated proteins artificially generated in order to identify specific motifs involved in channel retention/exportation. Altogether, our results indicate that a defect in KCNQ4 trafficking is the common mechanism underlying DFNA2

Novel Inductor‐less Conversion Strategy Based on Multiphase Transformer‐Coupled Converters: Analysis, Design and Applications

There are many the requirements that modern power converters should fulfill. Most of the applications where these converters are used, demand smaller converters with high efficiency, improved power density and a fast dynamic response. For instance, loads like microprocessors demand aggressive current steps with very high slew rates (100A/mus and higher); besides, during these load steps, the supply voltage of the microprocessor should be kept within tight limits in order to ensure its correct performance. The accomplishment of these requirements is not an easy task; complex solutions like advanced topologies - such as multiphase converters- as well as advanced control strategies are often needed. Besides, it is also necessary to operate the converter at high switching frequencies and to use capacitors with high capacitance and low ESR. Improving the dynamic response of power converters does not rely only on the control strategy but also the power topology should be suited to enable a fast dynamic response. Moreover, in later years, a fast dynamic response does not only mean accomplishing fast load steps but output voltage steps are gaining importance as well. At least, two applications that require fast voltage changes can be named: Low power microprocessors. In these devices, the voltage supply is changed according to the workload and the operating frequency of the microprocessor is changed at the same time. An important reduction in voltage dependent losses can be achieved with such changes. This technique is known as Dynamic Voltage Scaling (DVS). Another application where important energy savings can be achieved by means of changing the supply voltage are Radio Frequency Power Amplifiers. For example, RF architectures based on ‘Envelope Tracking’ and ‘Envelope Elimination and Restoration’ techniques can take advantage of voltage supply modulation and accomplish important energy savings in the power amplifier. However, in order to achieve these efficiency improvements, a power converter with high efficiency and high enough bandwidth (hundreds of kHz or even tens of MHz) is necessary in order to ensure an adequate supply voltage. The main objective of this Thesis is to improve the dynamic response of DC-DC converters from the point of view of the power topology. And the term dynamic response refers both to the load steps and the voltage steps; it is also interesting to modulate the output voltage of the converter with a specific bandwidth. In order to accomplish this, the question of what is it that limits the dynamic response of power converters should be answered. Analyzing this question leads to the conclusion that the dynamic response is limited by the power topology and specifically, by the filter inductance of the converter which is found in series between the input and the output of the converter. The series inductance is the one that determines the gain of the converter and provides the regulation capability. Although the energy stored in the filter inductance enables the regulation and the capability of filtering the output voltage, it imposes a limitation which is the concern of this Thesis. The series inductance stores energy and prevents the current from changing in a fast way, limiting the slew rate of the current through this inductor. Different solutions are proposed in the literature in order to reduce the limit imposed by the filter inductor. Many publications proposing new topologies and improvements to known topologies can be found in the literature. Also, complex control strategies are proposed with the objective of improving the dynamic response in power converters. In the proposed topologies, the energy stored in the series inductor is reduced; examples of these topologies are Multiphase converters, Buck converter operating at very high frequency or adding a low impedance path in parallel with the series inductance. Control techniques proposed in the literature, focus on adjusting the output voltage as fast as allowed by the power stage; examples of these control techniques are: hysteresis control, V 2 control, and minimum time control. In some of the proposed topologies, a reduction in the value of the series inductance is achieved and with this, the energy stored in this magnetic element is reduced; less stored energy means a faster dynamic response. However, in some cases (as in the high frequency Buck converter), the dynamic response is improved at the cost of worsening the efficiency. In this Thesis, a drastic solution is proposed: to completely eliminate the series inductance of the converter. This is a more radical solution when compared to those proposed in the literature. If the series inductance is eliminated, the regulation capability of the converter is limited which can make it difficult to use the topology in one-converter solutions; however, this topology is suitable for power architectures where the energy conversion is done by more than one converter. When the series inductor is eliminated from the converter, the current slew rate is no longer limited and it can be said that the dynamic response of the converter is independent from the switching frequency. This is the main advantage of eliminating the series inductor. The main objective, is to propose an energy conversion strategy that is done without series inductance. Without series inductance, no energy is stored between the input and the output of the converter and the dynamic response would be instantaneous if all the devices were ideal. If the energy transfer from the input to the output of the converter is done instantaneously when a load step occurs, conceptually it would not be necessary to store energy at the output of the converter (no output capacitor COUT would be needed) and if the input source is ideal, the input capacitor CIN would not be necessary. This last feature (no CIN with ideal VIN) is common to all power converters. However, when the concept is actually implemented, parasitic inductances such as leakage inductance of the transformer and the parasitic inductance of the PCB, cannot be avoided because they are inherent to the implementation of the converter. These parasitic elements do not affect significantly to the proposed concept. In this Thesis, it is proposed to operate the converter without series inductance in order to improve the dynamic response of the converter; however, on the other side, the continuous regulation capability of the converter is lost. It is said continuous because, as it will be explained throughout the Thesis, it is indeed possible to achieve discrete regulation; a converter without filter inductance and without energy stored in the magnetic element, is capable to achieve a limited number of output voltages. The changes between these output voltage levels are achieved in a fast way. The proposed energy conversion strategy is implemented by means of a multiphase converter where the coupling of the phases is done by discrete two-winding transformers instead of coupledinductors since transformers are, ideally, no energy storing elements. This idea is the main contribution of this Thesis. The feasibility of this energy conversion strategy is first analyzed and then verified by simulation and by the implementation of experimental prototypes. Once the strategy is proved valid, different options to implement the magnetic structure are analyzed. Three different discrete transformer arrangements are studied and implemented. A converter based on this energy conversion strategy would be designed with a different approach than the one used to design classic converters since an additional design degree of freedom is available. The switching frequency can be chosen according to the design specifications without penalizing the dynamic response or the efficiency. Low operating frequencies can be chosen in order to favor the efficiency; on the other hand, high operating frequencies (MHz) can be chosen in order to favor the size of the converter. For this reason, a particular design procedure is proposed for the ‘inductorless’ conversion strategy. Finally, applications where the features of the proposed conversion strategy (high efficiency with fast dynamic response) are advantageus, are proposed. For example, in two-stage power architectures where a high efficiency converter is needed as the first stage and there is a second stage that provides the fine regulation. Another example are RF power amplifiers where the voltage is modulated following an envelope reference in order to save power; in this application, a high efficiency converter, capable of achieving fast voltage steps is required. The main contributions of this Thesis are the following: The proposal of a conversion strategy that is done, ideally, without storing energy in the magnetic element. The validation and the implementation of the proposed energy conversion strategy. The study of different magnetic structures based on discrete transformers for the implementation of the proposed energy conversion strategy. To elaborate and validate a design procedure. To identify and validate applications for the proposed energy conversion strategy. It is important to remark that this work is done in collaboration with Intel. The particular features of the proposed conversion strategy enable the possibility of solving the problems related to microprocessor powering in a different way. For example, the high efficiency achieved with the proposed conversion strategy enables it as a good candidate to be used for power conditioning, as a first stage in a two-stage power architecture for powering microprocessors.

Reduced order modeling of three dimensional external aerodynamic flows

A method is presented to construct computationally efficient reduced-order models (ROMs) of three-dimensional aerodynamic flows around commercial aircraft components. The method is based on the proper orthogonal decomposition (POD) of a set of steady snapshots, which are calculated using an industrial solver based on some Reynolds averaged Navier-Stokes (RANS) equations. The POD-mode amplitudes are calculated by minimizing a residual defined from the Euler equations, even though the snapshots themselves are calculated from viscous equations. This makes the ROM independent of the peculiarities of the solver used to calculate the snapshots. Also, both the POD modes and the residual are calculated using points in the computational mesh that are concentrated in a close vicinity of the aircraft, which constitute a much smaller number than the total number of mesh points. Despite these simplifications, the method provides quite good approximations of the flow variables distributions in the whole computational domain, including the boundary layer attached to the aircraft surface and the wake. Thus, the method is both robust and computationally efficient, which is checked considering the aerodynamic flow around a horizontal tail plane, in the transonic range 0.4?Mach number?0.8, ?3°?angle of attack?3°.

Pulse shortening of gain switched single mode semiconductor lasers using a variable delay interferometer

We propose a pulse shaping and shortening technique for pulses generated from gain switched single mode semiconductor lasers, based on a Mach Zehnder interferometer with variable delay. The spectral and temporal characteristics of the pulses obtained with the proposed technique are investigated with numerical simulations. Experiments are performed with a Distributed Feedback laser and a Vertical Cavity Surface Emitting Laser, emitting at 1.5 µm, obtaining pulse duration reduction of 25-30%. The main asset of the proposed technique is that it can be applied to different devices and pulses, taking advantage of the flexibility of the gain switching technique.

IBPOWER Project, Intermediate band materials and solar cells for photovoltaics with high efficiency and reduced cost

IBPOWER is a Project awarded under the 7th European Framework Programme that aims to advance research on intermediate band solar cells (IBSCs). These are solar cells conceived to absorb below bandgap energy photons by means of an electronic energy band that is located within the semiconductor bandgap, whilst producing photocurrent with output voltage still limited by the total semiconductor bandgap. IBPOWER employs two basic strategies for implementing the IBSC concept. The first is based on the use of quantum dots, the IB arising from the confined energy levels of the electrons in the dots. Quantum dots have led to devices that demonstrate the physical operation principles of the IB concept and have allowed identification of the problems to be solved to achieve actual high efficiencies. The second approach is based on the creation of bulk intermediate band materials by the insertion of an appropriate impurity into a bulk semiconductor. Under this approach it is expected that, when inserted at high densities, these impurities will find it difficult to capture electrons by producing a breathing mode and will cease behaving as non-radiative recombination centres. Towards this end the following systems are being investigated: a) Mn: In1-xGax N; b) transition metals in GaAs and c) thin films.

Comparison of V2IC control with voltage mode and current mode controls for high frequency (MHz) and very fast response applications

High switching frequencies (several MHz) allow the integration of low power DC/DC converters. Although, in theory, a high switching frequency would make possible to implement a conventional Voltage Mode control (VMC) or Peak Current Mode control (PCMC) with very high bandwidth, in practice, parasitic effects and robustness limits the applicability of these control techniques. This paper compares VMC and CMC techniques with the V2IC control. This control is based on two loops. The fast internal loop has information of the output capacitor current and the error voltage, providing fast dynamic response under load and voltage reference steps, while the slow external voltage loop provides accurate steady state regulation. This paper shows the fast dynamic response of the V2IC control under load and output voltage reference steps and its robustness operating with additional output capacitors added by the customer.

Multiple Input-Output Bidirectional Solid State Transformer Based on a Series Resonant Converter

Las fuentes de alimentación de modo conmutado (SMPS en sus siglas en inglés) se utilizan ampliamente en una gran variedad de aplicaciones. La tarea más difícil para los diseñadores de SMPS consiste en lograr simultáneamente la operación del convertidor con alto rendimiento y alta densidad de energía. El tamaño y el peso de un convertidor de potencia está dominado por los componentes pasivos, ya que estos elementos son normalmente más grandes y más pesados que otros elementos en el circuito. Para una potencia de salida dada, la cantidad de energía almacenada en el convertidor que ha de ser entregada a la carga en cada ciclo de conmutación, es inversamente proporcional a la frecuencia de conmutación del convertidor. Por lo tanto, el aumento de la frecuencia de conmutación se considera un medio para lograr soluciones más compactas con los niveles de densidad de potencia más altos. La importancia de investigar en el rango de alta frecuencia de conmutación radica en todos los beneficios que se pueden lograr: además de la reducción en el tamaño de los componentes pasivos, el aumento de la frecuencia de conmutación puede mejorar significativamente prestaciones dinámicas de convertidores de potencia. Almacenamiento de energía pequeña y el período de conmutación corto conducen a una respuesta transitoria del convertidor más rápida en presencia de las variaciones de la tensión de entrada o de la carga. Las limitaciones más importantes del incremento de la frecuencia de conmutación se relacionan con mayores pérdidas del núcleo magnético convencional, así como las pérdidas de los devanados debido a los efectos pelicular y proximidad. También, un problema potencial es el aumento de los efectos de los elementos parásitos de los componentes magnéticos - inductancia de dispersión y la capacidad entre los devanados - que causan pérdidas adicionales debido a las corrientes no deseadas. Otro factor limitante supone el incremento de las pérdidas de conmutación y el aumento de la influencia de los elementos parásitos (pistas de circuitos impresos, interconexiones y empaquetado) en el comportamiento del circuito. El uso de topologías resonantes puede abordar estos problemas mediante el uso de las técnicas de conmutaciones suaves para reducir las pérdidas de conmutación incorporando los parásitos en los elementos del circuito. Sin embargo, las mejoras de rendimiento se reducen significativamente debido a las corrientes circulantes cuando el convertidor opera fuera de las condiciones de funcionamiento nominales. A medida que la tensión de entrada o la carga cambian las corrientes circulantes incrementan en comparación con aquellos en condiciones de funcionamiento nominales. Se pueden obtener muchos beneficios potenciales de la operación de convertidores resonantes a más alta frecuencia si se emplean en aplicaciones con condiciones de tensión de entrada favorables como las que se encuentran en las arquitecturas de potencia distribuidas. La regulación de la carga y en particular la regulación de la tensión de entrada reducen tanto la densidad de potencia del convertidor como el rendimiento. Debido a la relativamente constante tensión de bus que se encuentra en arquitecturas de potencia distribuidas los convertidores resonantes son adecuados para el uso en convertidores de tipo bus (transformadores cc/cc de estado sólido). En el mercado ya están disponibles productos comerciales de transformadores cc/cc de dos puertos que tienen muy alta densidad de potencia y alto rendimiento se basan en convertidor resonante serie que opera justo en la frecuencia de resonancia y en el orden de los megahercios. Sin embargo, las mejoras futuras en el rendimiento de las arquitecturas de potencia se esperan que vengan del uso de dos o más buses de distribución de baja tensión en vez de una sola. Teniendo eso en cuenta, el objetivo principal de esta tesis es aplicar el concepto del convertidor resonante serie que funciona en su punto óptimo en un nuevo transformador cc/cc bidireccional de puertos múltiples para atender las necesidades futuras de las arquitecturas de potencia. El nuevo transformador cc/cc bidireccional de puertos múltiples se basa en la topología de convertidor resonante serie y reduce a sólo uno el número de componentes magnéticos. Conmutaciones suaves de los interruptores hacen que sea posible la operación en las altas frecuencias de conmutación para alcanzar altas densidades de potencia. Los problemas posibles con respecto a inductancias parásitas se eliminan, ya que se absorben en los Resumen elementos del circuito. El convertidor se caracteriza con una muy buena regulación de la carga propia y cruzada debido a sus pequeñas impedancias de salida intrínsecas. El transformador cc/cc de puertos múltiples opera a una frecuencia de conmutación fija y sin regulación de la tensión de entrada. En esta tesis se analiza de forma teórica y en profundidad el funcionamiento y el diseño de la topología y del transformador, modelándolos en detalle para poder optimizar su diseño. Los resultados experimentales obtenidos se corresponden con gran exactitud a aquellos proporcionados por los modelos. El efecto de los elementos parásitos son críticos y afectan a diferentes aspectos del convertidor, regulación de la tensión de salida, pérdidas de conducción, regulación cruzada, etc. También se obtienen los criterios de diseño para seleccionar los valores de los condensadores de resonancia para lograr diferentes objetivos de diseño, tales como pérdidas de conducción mínimas, la eliminación de la regulación cruzada o conmutación en apagado con corriente cero en plena carga de todos los puentes secundarios. Las conmutaciones en encendido con tensión cero en todos los interruptores se consiguen ajustando el entrehierro para obtener una inductancia magnetizante finita en el transformador. Se propone, además, un cambio en los señales de disparo para conseguir que la operación con conmutaciones en apagado con corriente cero de todos los puentes secundarios sea independiente de la variación de la carga y de las tolerancias de los condensadores resonantes. La viabilidad de la topología propuesta se verifica a través una extensa tarea de simulación y el trabajo experimental. La optimización del diseño del transformador de alta frecuencia también se aborda en este trabajo, ya que es el componente más voluminoso en el convertidor. El impacto de de la duración del tiempo muerto y el tamaño del entrehierro en el rendimiento del convertidor se analizan en un ejemplo de diseño de transformador cc/cc de tres puertos y cientos de vatios de potencia. En la parte final de esta investigación se considera la implementación y el análisis de las prestaciones de un transformador cc/cc de cuatro puertos para una aplicación de muy baja tensión y de decenas de vatios de potencia, y sin requisitos de aislamiento. Abstract Recently, switch mode power supplies (SMPS) have been used in a great variety of applications. The most challenging issue for designers of SMPS is to achieve simultaneously high efficiency operation at high power density. The size and weight of a power converter is dominated by the passive components since these elements are normally larger and heavier than other elements in the circuit. If the output power is constant, the stored amount of energy in the converter which is to be delivered to the load in each switching cycle is inversely proportional to the converter’s switching frequency. Therefore, increasing the switching frequency is considered a mean to achieve more compact solutions at higher power density levels. The importance of investigation in high switching frequency range comes from all the benefits that can be achieved. Besides the reduction in size of passive components, increasing switching frequency can significantly improve dynamic performances of power converters. Small energy storage and short switching period lead to faster transient response of the converter against the input voltage and load variations. The most important limitations for pushing up the switching frequency are related to increased conventional magnetic core loss as well as the winding loss due to the skin and proximity effect. A potential problem is also increased magnetic parasitics – leakage inductance and capacitance between the windings – that cause additional loss due to unwanted currents. Higher switching loss and the increased influence of printed circuit boards, interconnections and packaging on circuit behavior is another limiting factor. Resonant power conversion can address these problems by using soft switching techniques to reduce switching loss incorporating the parasitics into the circuit elements. However the performance gains are significantly reduced due to the circulating currents when the converter operates out of the nominal operating conditions. As the input voltage or the load change the circulating currents become higher comparing to those ones at nominal operating conditions. Multiple Input-Output Many potential gains from operating resonant converters at higher switching frequency can be obtained if they are employed in applications with favorable input voltage conditions such as those found in distributed power architectures. Load and particularly input voltage regulation reduce a converter’s power density and efficiency. Due to a relatively constant bus voltage in distributed power architectures the resonant converters are suitable for bus voltage conversion (dc/dc or solid state transformation). Unregulated two port dc/dc transformer products achieving very high power density and efficiency figures are based on series resonant converter operating just at the resonant frequency and operating in the megahertz range are already available in the market. However, further efficiency improvements of power architectures are expected to come from using two or more separate low voltage distribution buses instead of a single one. The principal objective of this dissertation is to implement the concept of the series resonant converter operating at its optimum point into a novel bidirectional multiple port dc/dc transformer to address the future needs of power architectures. The new multiple port dc/dc transformer is based on a series resonant converter topology and reduces to only one the number of magnetic components. Soft switching commutations make possible high switching frequencies to be adopted and high power densities to be achieved. Possible problems regarding stray inductances are eliminated since they are absorbed into the circuit elements. The converter features very good inherent load and cross regulation due to the small output impedances. The proposed multiple port dc/dc transformer operates at fixed switching frequency without line regulation. Extensive theoretical analysis of the topology and modeling in details are provided in order to compare with the experimental results. The relationships that show how the output voltage regulation and conduction losses are affected by the circuit parasitics are derived. The methods to select the resonant capacitor values to achieve different design goals such as minimum conduction losses, elimination of cross regulation or ZCS operation at full load of all the secondary side bridges are discussed. ZVS turn-on of all the switches is achieved by relying on the finite magnetizing inductance of the Abstract transformer. A change of the driving pattern is proposed to achieve ZCS operation of all the secondary side bridges independent on load variations or resonant capacitor tolerances. The feasibility of the proposed topology is verified through extensive simulation and experimental work. The optimization of the high frequency transformer design is also addressed in this work since it is the most bulky component in the converter. The impact of dead time interval and the gap size on the overall converter efficiency is analyzed on the design example of the three port dc/dc transformer of several hundreds of watts of the output power for high voltage applications. The final part of this research considers the implementation and performance analysis of the four port dc/dc transformer in a low voltage application of tens of watts of the output power and without isolation requirements.

Sobre la Arquitectura en la definición del Paisaje

Comúnmente la Arquitectura se manifiesta en los edificios como un hecho de la realidad que tiene siempre carácter contemporáneo y ése debe ser el valor supremo de un arte que no distingue entre antiguo y moderno, por afectar al presente y ser contemporáneo como experiencia. Los objetos se insertan irremediablemente en su medio e incluso llegan a definirlo en ocasiones: así, arquitectura y paisaje, aparecerán a veces confundidos con diferencias difíciles de determinar. El término “paisaje” es relativamente moderno y se deriva de ciertas representaciones gráficas o pictóricas producidas en Occidente en época algo posterior al Renacimiento. No obstante, el hecho de que una palabra se pueda escribir o se cite no quiere decir que la realidad a la que responde no pueda existir, pues lo escrito es solamente un medio de expresión, y es obvio que existen otros quizá más antiguos y de idéntica importancia, pues la propia escritura no es más que el reflejo de un fenómeno que ya se ha producido con anterioridad. Parece así que el testimonio de la realidad viene dado por distintos contextos en lo que suele llamarse “cultura” de modo que las culturas pueden tener aspectos de gran interés mediante diferentes sistemas de expresión variados sin que eso tenga que pasar forzosamente por el filtro de un alfabeto y una escritura. A tenor de los primeros descubrimientos, parece que la cuestión de escribir tuvo originalmente un carácter de constatación de apunte contable y tampoco se puede establecer con certeza si algunos utilizaron la escritura como el so-porte adecuado para referir mitos o historias, pues la Arqueología no ha proporcionado sino testimonios fragmentarios; de lo que si está repleta sin duda la historia es de apuntes contables. Otra cuestión que suscita dudas es la propia definición de escritura, pues parece que los más antiguos modos de expresión escrita se reducen a pictogramas que resultan aún indescifrables. Lenguas y toponimia son también herramientas muy útiles para bucear en el pasado, pero aún así persisten dudas en las escrituras que pro-vienen de las representaciones primordiales: la propia escritura en sus orígenes parece alimentarse de las propias intuiciones inmediatas de la representación, algo que evolucionaría representando esa realidad urgente e inmediata del control o el abastecimiento que luego se convertirían en los fragmentos de texto que han podido conservarse. Es notorio, sin embargo, que ese conjunto enorme de convenios gráficos estaba sujeto a la palabra y la desaparición de las culturas determinó también la desaparición consecuente de sus lenguas, y esos signos - fueran o no escritura - han pasado definitivamente a las zonas oscuras del conocimiento. Escribir supone también disponer de capacidad de abstracción gráfica que diferencie la palabra y la cosa, y es posible que la razón que llevara a ese descubrimiento fuera simplemente el de una economía de signos, pues escritura y lenguaje son limitados por definición, mientras que las cosas del mundo son innumerables: ningún idioma contiene todas las palabras para describir todo lo que puede aparecer. Aparentemente, ese el motivo por el cual existe un localismo – un término específico que refiere algo que existe en un lugar y no en otros - en lo que se refiere a dar el nombre a la cosa y también fuente de paradigma entre los pueblos que se consideran primitivos y los que se consideran civilizados. Debe tenerse en cuenta también que esa transposición se da en ambos sentidos, de modo que las culturas más aisladas también incorporan conceptos que carecen de una explicación racional consistente. Las mitologías son así eternas, pues sirven para explicar realidades que carecen de un entendimiento alcanzable y está también bastante claro que los lenguajes resultan ser un enigma, como realidad autónoma que queda en-cerrada y se explica en sí misma. Parece también que los primeros en escribir las consonantes aisladas fueron los pueblos semíticos occidentales de las orillas del Mediterráneo, pueblos que crearon un alfabeto silábico que llegó a ser utilizado incluso por los tartesios en el sur de la península ibérica como el primer alfabeto de toda Europa occidental. Resulta patente que el término “paisaje” se ha nutrido siempre de representaciones, bien escritas o artísticas, pero queda también claro que esas representaciones se suponen derivadas de la creencia en una idea de paisaje como algo que se ve representado en sí mismo, es decir, como la imagen de una realidad externa situada fuera del individuo. Eso es un hecho trascendente, pues el paisaje requiere lejanía de la cosa, de modo que el actor – aún sabiéndose inserto en su paisaje – es incapaz de percibirlo desde dentro. En el paisaje ocurre igual que en un teatro o en una representación: los actores son conscientes de su papel y su posible cometido, pero no son los que realmente pueden disfrutar de la eficacia o de la propia presencia de la obra, pues forman parte de ella. La idea de paisaje proviene de una lectura externa a la de los propios protagonistas del drama, de modo que si quieren ser un crítico del paisaje se debe abandonar la representación para mirar el espectáculo desde una distancia adecuada, al fin y a cabo externa. De ese modo, aparece la primera constatación del hecho del paisaje como una realidad construida por objetos y personajes, pero, sobre todo, es una realidad construida por miradas. Llama también la atención otorgada en las lecturas de los especialistas hacia esa referencia externa - artística si se quiere - sobre el término “paisaje”, de modo que la bibliografía no especializada sobre el particular siempre acaba en tratados de pintura o poesía. Parece sin embargo que el hombre y sus paisajes son realidades indisolubles desde la propia aparición de la especie, de modo que llevar la cuestión hacia términos exclusivamente esteticistas parece una posición parcial. Hombre y medio han formado siempre una sola unidad, aunque esa unidad se haya convertido en determinados casos en sinónimo de depredación y destrozo. Sin embargo, esa destrucción crea igualmente un paisaje como desolación que es resultado del propio quehacer del hombre: elementos que también poseen un contenido sustancial de memoria en los paisajes industriales como un momento de la Historia previo a la automatización y a la globalización de la vida actuales. Quizá el concepto más interesante desde el punto de vista teórico sea precisamente el de esa cualidad del paisaje como mirada, algo externo producido por el contemplador en un momento ajeno a la pertenencia, una mirada que no es tan sólo estética sino comprensiva, gozosa, activa o analítica - pues existen tantas maneras de mirar como sujetos - sin que pueda definirse con precisión esa contemplación más que en términos que alcanzan la propia individualidad. En términos poéticos, también podría establecerse como ese conjunto de miradas individuales crean también una estructura que hace que ese paisaje se valore y se comprenda, de modo que desde ese punto de vista ese paisaje supone una creación colectiva. Con respeto o como depredador, el hombre se ha instalado en su medio, y al hacerlo, ha dejado huellas dentro del propio paisaje que hacen que tome una determinada significación. Naturalmente, existe una teoría que distingue entre “país” y “paisaje”, asumiendo para el primero la noción exclusiva de territorio en la cual el hombre no tiene papel estético alguno. He intentado muchas veces comprender esa posición, sin acabar de entender el planteamiento que la sustenta: parece que la visión de la cosa estará siempre humanizada, aún en las zonas “vírgenes” o intactas, pues la propia visión hace que el objeto se modifique en su propia unidad perceptiva, creando una curiosa indeterminación que lleva a los conocidos equívocos entre imagen real y representación. Efectivamente, la visión de la cosa requiere de una cultura y unos medios que la informan, de modo que un texto, una pintura, una descripción o una fotografía quedarán ya humanizadas por el propio hecho de ser informadas, pues ello otorga una forma a priori. De ese modo, el paisaje figura inscrito en una función que establece tanto aspectos de un paisaje posible como aspectos del paisaje descrito y solamente podrá hablarse sobre la potencialidad del estado final de ese paisaje y nada del propio paisaje en sí, mientras ese paisaje no quede humanizado por el propio observador. Esta cuestión obliga a elegir una definición de paisaje alejada de presupuestos esteticistas para acercarla a los puramente culturales, de modo que no existe otra vía para la investigación que contemplar esa realidad física en función de las coordenadas del hombre que la habita, dotada del contenido correspondiente a esa revelación. Lejos de las posiciones de la geomorfología, el término “paisaje” implicará así unas condiciones determinadas de contemplación por parte de un sujeto por el cual el espectáculo queda humanizado en dicho acto.Cabe pensar también si no es cierto que todos los paisajes requieren de esa condición humanizada, pues aunque no estén habitados están siempre ocupados por esa mirada que los habita, al igual que un escenario sin público que carece de vigencia. A partir de ahí se sitúan las coordenadas en donde este trabajo configura la presencia de la arquitectura en la definición del paisaje, una premisa que parece ya venir otorgada desde el principio, pues esa misma mirada del espectador ya está dotando de un sentido de orden y jerarquía a la contemplación, unas cualidades que están en la base de toda actividad arquitectónica, De hecho la propia definición de “monumento natural” - en si misma una contradicción – expresa ese conflicto, dotado de un fenómeno de admiración y solape entre cultura y naturaleza, como conceptos enfrentados desde su origen. La conclusión sobre el dilema propuesta en la tesis no ha sido otra que suponer que esas dos realidades que son la cultura y el paisaje se han solapado desde el principio de los tiempos del hombre formando un binomio indeslindable. Se ha dicho antes que el proceso de invasión del territorio por el hombre es significativo, y esa significación es la que origina una creación autónoma que se aísla como un concepto abstracto de los entes naturales, tomándolos como material de trabajo, y estableciendo una oposición conceptual en la realidad perforada e interpretada por el hombre que viene a oponerse a lo que supone la caja cerrada e ignota del enigma del mundo. La cuestión de la significación del hombre sobre el territorio se subsume en la creación de unos productos que permanecen y que son testimonio de la propia cultura, de forma que la cantidad de rastro que el hombre deja sobre el territorio contribuye en mayor medida a la cualificación del paisaje como concepto. Eso lleva a establecer que cualquier paisaje - por el mero hecho de serlo y ser definido así – es ya cultural, puesto que está configurado por los productos de la cultura. Las palabras que puedan quedar encerradas en las piedras de los monumentos o de las ciudades son las de los hombres que trabajaron allí, y también las de los que las habitaron: más aún, el propio sentido del paisaje y su conservación vienen determinados por la presencia del hombre como único interprete de conceptos como ecología o conservación, algo que se pone de manifiesto también en la espantosa devastación que producen los fenómenos propios de la naturaleza. La historia natural, al igual que la vida, están conformadas por éxito y devastación, sin que uno y otra tengan especial preferencia, pues la preferencia se alimenta de otra clase de conceptos. La cuestión de atribuir valores morales al mundo natural es algo muy antiguo, y quizá sea la fuente o el manantial de las primeras religiones, una cuestión que se une a la indefectible noción de mortalidad que define la existencia del hombre frente a la inmanencia de la naturaleza. Esa propia naturaleza está dotada intuitivamente de un carácter “inocente” suponiendo que la inocencia es lo opuesto a la sabiduría. La cuestión es bien otra, ya que la naturaleza no posee ni siquiera algo que pueda definirse como “carácter”, en el sentido personal del término. La cuestión no cae, evidentemente, del lado de las definiciones o de las cualidades, sino del propio análisis de la realidad que el hombre va construyendo, destruyendo, embelleciendo o perjudicando para definir el territorio que habita, interponiendo a su manera recursos, instalaciones y en definitiva todos los testimonios posibles como principal manifestación de su esencia. Entre los artefactos que el hombre produce, uno de los más persistentes y más conspicuamente descritos es el de la arquitectura - entendida aquí en un sentido amplio - es decir, como el conjunto de modificaciones del espacio y del territorio. El espacio se puede modificar de muchos modos, pero en cualquiera de los casos constituye una de las huellas más características que el hombre establece como manifestación física de su propio ser discursivo. También la arquitectura ha demostrado ser una de los fenómenos más persistentes, incluso más que la propia lengua que la origina en su discurso primero antes que pueda ac-cederse a una idea sobre la conformación del material. Es paradigmático que el episodio descrito sobre la Torre de Babel en la Biblia la cuestión de la ambición de los hombres frente a Dios, representada precisamente en una arquitectura, se asimile a la discusión sobre el lenguaje primordial. La cuestión no es baladí, pues el fenómeno de la creación es algo que se concede exclusivamente a los dioses, que por esa razón habitan los territorios a los que los hombres no pueden llegar; territorios de albergue en los que las mitologías sitúan a dioses y demonios, con amplios espacios intermedios donde situar a las divinidades menores, héroes o seres híbridos en los que la coyunda de los dioses con los humanos produce sujetos que alivian el sentido de la mortalidad. El comentario del Génesis también concede un valor a la técnica, al mito de Prometeo y al fuego como creador de excelencia. Frente al progreso prometeico, se postula el valor divino, y la única forma posible de paliar ese progreso es la confusión del lenguaje, pues eso será lo que produzca la dispersión y la falta de acuerdo. La cuestión también puede explicar esa afición tan común por lo canónico en arquitectura que se mantiene a lo largo de grandes períodos, al igual que una gran máquina de inercia. Parece que los conceptos primordiales de la arquitectura basados en elementos simples como el hito, el dintel, lo recto y lo curvo, la rampa o la escalera, y el uso distinto o cualificado que se otorga a la piedra, el ladrillo, la madera o el metal como componentes primordiales del material arquitectónico se haya mantenido a lo largo de muchos milenios sin apenas cambios, al igual que ocurre con las costumbres alimenticias que siguen una progresión ascendente a través de lo crudo, lo asado y lo cocido, hasta obtener distintos grados de refina-miento, pero que siempre se sustentan en la sensación primigenia. El descubrimiento de la arquitectura proviene de un cierto manejo de las dimensiones, y consiguientemente de la geometría. Pero la geometría es cosa abstracta al igual que el lenguaje, de modo que para poder realizar arquitectura se hace necesaria esa capacidad de abstracción primera que luego permite la realización de un dispositivo. La realidad y su número exhiben un divorcio, al igual que las cosas y sus nombres exhiben el suyo, y el análisis numérico es solamente una forma de ver la realidad, una forma rigurosa y exacta – aunque parcial - que solamente representa el modelo ideal al cual la realidad se aproxima en mayor o menor medida: esa aproximación matemática hace que el universo pueda condensarse parcialmente en números, al igual que la realidad puede condensarse en nombres, pero ni el nombre ni el número reflejarán el mundo en toda su complejidad. El número es quizá solamente un medio de describir las cosas, como lo serían las formas puras que responden a una configuración matemática que pueda producirse en teoría en cualquier parte del Universo. Sin embargo, para el ejercicio de la arquitectura es preciso acudir a esa simplificación que exige la visión abstracta del plano como una sección cierta realidad como un corte abstracto del elemento considerado. Con su traza o sin ella, con la propia expresión matemática que lo describa o sin precisarla, esa intuición del plano como elemento generador del espacio es anterior a aquella expresión, al igual que el habla fue anterior a la escritura, pues solamente se produjo a través de ella y como refuerzo y sustituto de la memoria. Existen así abstracciones de la memoria que aparecen derivadas de los signos de la naturaleza aparecidos solamente de forma eventual y fragmentaría: así ocurre con la línea, el cuadrado y el círculo, formas iniciales y abstractas sonsacadas en cierta medida de la observación que dan origen a los primeros signos de la arquitectura primordial, de modo que cuadrados y círculos, elevados a prismas y superficies esféricas o esferoides aparecen en tumbas y edificios elementales de los primeros tiempos mediante una geometría primordial que se superpone al paisaje en el que se inserta. Es cierto también que esas formas se encuentran ya aproximadas en objetos que se encuentran en el medio físico, líneas en extremidades, ramas y miembros; ángulos rectos en algunos cristales que se observan mediante corte o formas circulares en astros y cráteres, pero esa realidad solamente presenta su forma aproximada y no su abstracción pura, de igual modo que el jeroglífico propondrá al ave rapaz para representar la idea de vigilancia y la buena vista, o incluso que la imagen del propio ojo sustituya la idea del Dios que todo lo ve en las culturas anti-guas. La elección fue resuelta, después de muchos intentos y aproximaciones, con la adopción del ángulo recto como un artificio fácil para el replanteo a través del triángulo sagrado 3:4:5 que ya se utilizó para construir las pirámides de Egipto, y que dio origen también a la mayor parte del urbanismo antiguo, coexistiendo con la forma circular primordial en el tipo denominado “tholo”. Aquella trama cuadrangular era uno de los patrones de relleno del espacio más comunes y compactos, y esa fue probablemente la razón por la que en tiempos muy posteriores fuera adoptada como una forma eficaz permanente de organización frente al desorden topológico que procura el conjunto de asociación de plantas circulares. Otra cuestión paradigmática es que esos conceptos primordiales e ignotos - que convergen en el mismo origen de las civilizaciones - se conviertan luego en algo canónico, a través del uso. El canon en sí mismo es algo ideal, como una norma aplicable a objetos de una realidad que ha sido creada solamente como indicio del ca-non, algo abstracto que tiene proporciones estrictas que son siempre las mismas y no obedece a criterios racionales: será absurdo sin embargo buscar el canon griego entre los templos de época como algunos lo hicieron, pues los edificios solamente se aproximan a los ejemplos canónicos y por esa razón se habla del “dórico del Partenón” que es diferente del de Egina o del de Paestum, siendo todos ellos evidentemente dóricos. Sin embargo, esa idea resulta útil al tratadista, al teórico de la arquitectura y al historiador, aun-que solamente refleje una vaga idea de lo que sucede más allá del tratado. Otra cuestión es la sutileza de los ejemplos de arquitectura, y del mismo modo que los cuerpos de los seres vivos jamás son simétricos, aunque respondan a un diseño simétrico general derivado de las condiciones de la división celular, los edificios supuestamente canónicos en los que los especialistas se inspiraron para definir los órdenes clásicos no disponen de esa simetría modular exacta, sino que adaptan un modelo general al lugar siempre cambiante del emplazamiento, es decir, se adaptan con habilidad a la vez que configuran el paisaje en el que se insertan. La luz de los distintos intercolumnios del Partenón es ligeramente distinta, aunque guarde un evidente sentido de simetría axial, de manera que aquellos “órdenes” que formaron la Teoría de la Arquitectura no son más que una bella interpretación sectorial de la arquitectura antigua elaborada por los tratadistas del Renacimiento y, posteriormente, por los neoclásicos. Parece, sin embargo, que ese ansia por el canon como claridad de lenguaje es algo consustancial al desarrollo de la arquitectura, una lingua franca que tiende a evitar la dispersión producida entre los mortales por los dioses antiguos, de modo que si no era posible llegar al cielo de los dioses se procuró que el lenguaje de la Tierra fuera al menos inteligible para poder entenderse entre los hombres. Parece que la estructura del poder siempre requirió de un determinado nivel de organización, y también que las instrucciones se entendieran con claridad: parece que en nuestros tiempos esos antiguos cánones se han sustituido por la obediencia a normas abstractas, dictadas por instituciones también algo abstractas y que tienen nombres divertidos compuestos por siglas, aunque no se conozca bien su virtud. El canon actual está constituido por “normas” que dejan tranquilos a algunos, aunque parece quizá que todo ese entramado formal que sirve como anestesia para el cuerpo social procura también la destrucción de los bosques en formas de montañas ingentes de papel burocrático. Durante muchos siglos las normas fueron otras, en la forma de un canon del cual nadie podía escapar: aún así, mediante la utilización de cánones o sin ellos, la arquitectura prosperó en la civilización desde los primeros refugios cavernarios o los abrigos primigenios y de ese modo fue configurando la realidad, es decir, el paisaje. Como antes se dijo, ese es un viaje de ida y vuelta en el cual ambos se confundían y subsumían: el manejo de las formas y lenguajes de la arquitectura posibilitaría con el tiempo la distinción entre el campo en donde reina el caos y la ciudad, en donde reina teóricamente el orden, creando un divorcio que duraría milenios y que aún persiste. Esa oposición generaría también una forma de paisaje y una serie de usos simbólicos y sagrados de los elementos de la arquitectura - como son puertas y murallas - que se han mantenido conceptualmente aunque hoy las ciudades ya no posean murallas físicas, ni puertas que se cierran con la llegada de la noche. En ese sentido, la arquitectura ha podido definir el paisaje, entendiendo la arquitectura no solamente como los edificios en sí, sino como el hecho de la manifestación del hombre sobre el territorio, de modo que no podrá hablarse de paisaje sin su arquitectura, del mismo modo que no puede hablarse de paisaje sin hombres. Por esta razón, la Tesis habla sobre Arquitectura y Paisaje, pero más particularmente sobre el hecho de la arquitectura en la definición del paisaje, es decir, de como los hechos arquitectónicos van a determinar o no la cualidad y la calificación de un paisaje. Deberá partirse en primer lugar de una definición de lo que se entiende y se ha entendido comúnmente por paisaje: igualmente, y habida cuenta del contexto en el que sitúa el propio trabajo de tesis, la cuestión solamente se circunscribirá a lo que se entiende como cultura occidental, pues el desarrollo de la civilización presenta siempre un color local que hace que el análisis de un fenómeno de esta envergadura tenga distintas connotaciones en las distintas áreas de civilización. De igual modo, y habida cuenta también que el paisaje se construye a través de todas las manifestaciones culturales, se hará a veces necesario indagar en otras disciplinas no arquitectónicas para comprender el alcance de algunos casos en los cuales los restos arquitectónicos han desaparecido, o en los que subsisten escasas trazas. Una definición tan amplia de la Arquitectura llevaría a escribir un relato sobre toda la cultura occidental y por ese motivo solamente se han esbozado ideas sobre la aparición de esos signos sobre el paisaje basados en elementos antiguos y primigenios que se repiten con insistencia y van dando lugar al variado repertorio de la arquitectura occidental cómo conformación de ideas sobre el me-dio y sobre el mundo que se percibe y se habita. ABSTRACT About Architecture in defining Landscape. Abstract Architecture is commonly manifested in buildings as a fact of reality that has always a contemporary character and that should be the highest value of an art that does not distinguish between ancient and modern, to affect the present and be contemporary as experience. Objects are inserted irremediably in their midst and even sometimes come to define it: thus, architecture and landscape, appear sometimes confused with differences difficult to determine. However, the term "landscape" is relatively modern and is derived from certain graphical or pictorial representations produced in the West in some subsequent period to the Renaissance. The fact that a word can be written or quoting does not mean that the reality that can not be answered, because the writing is only a mean of expression, and it is obvious that there are other and perhaps older equally important, because the writing itself is nothing more than the reflection of a phenomenon that has occurred before. It thus appears that the testimony of reality is given by different contexts in what is called "culture", so that cultures can have aspects of great interest by many different expression systems without this necessarily have to pass through the filter of alphabet and writing. Under the initial findings, it appears that the question of writing originally had a character and finding accounting entries, and it can not be established with certainty whether some used writing as the support appropriate to refer myths or stories, because archaeology has provided only fragmentary evidence. Another issue that raises questions is what can properly be defined as writing, it seems that the oldest modes are reduced to writing pictograms are still indecipherable. Languages and place names are also very useful tools for diving in the past, but still questions remain in the scriptures that come from the primordial representations: either it is very well defined what the own writing in its origins: the beginnings seem to feed on immediate intuitions of representation, which would evolve representing reality that urgent and immediate control or supply which is then inherited into fragments. It is noteworthy, however, that this huge set of graphics agreements was subject to the word and the disappearance of cultures determined also the consequent disappearance of their languages, and those signs - whether or not they write - have passed definitively to dark areas of knowledge. Writings supposed also the capacity of abstraction graph differentiates the word and the thing, and it is possible that the reason to carry this discovery was simply that of an economy of signs, for writing and language are limited by definition, while the things of the world are innumerable: no language contains all words to describe all that may appear. Apparently, that's why there is a localism - a specific term that refers to something that exists in one place and not in others - in regards to name the thing and also the source of paradigm among peoples are considered primitive and civilized. It should be noted also that transposition occurs in both directions, so that the most isolated cultures also incorporate concepts that lack a consistent rational explanation. Mythologies are eternal and therefore serve to explain realities that lack an understanding achievable and also pretty clear that languages happen to be an enigma, as an autonomous reality that is enclosed and explains itself. It also seems that the first to write consonants were isolated western Semitic peoples from the shores of the Mediterranean, peoples who created a syllabic alphabet came to be used even by tartesios in southern Iberia as the first alphabet in Western Europe. It is clear that the term "landscape" has always nurtured representations, either written or artis-tic, but it is also clear that these representations are assumed arising from belief in an idea of landscape as something that is represented in itself, as the image of a reality external located outside the individual. That is an important fact because the landscape requires remoteness of the thing, so that the actor - even knowing insert in landscape - is unable to perceive from within. The landscape is just as in a theatre or a performance: the actors are aware of their role and their possible role, but they are not the ones who can really enjoy the efficiency or the presence of the work itself, as part of it. The idea comes from an external landscape reading the principles of players in the drama, so if you want to be a critic of the landscape should leave the actual representation to watch the spectacle from a safe distance, finally external. Thus, the first finding of fact of the landscape appears as a reality constructed by objects and characters, but above all, a reality constructed by looks. Also noteworthy given the readings of specialists to the external reference - art if it could be - on the term "landscape", so no specialized literature on the subject always ends in treatises on painting or poetry. It seems however that the man and his landscapes are inseparable realities from the very onset of the species, so bring the issue into terms exclusively aesthetics seems a partial position. Man and environment have always been a single unit, but that unit has become synonymous with certain cases predation and destruction. Nevertheless, this destruction also creates a landscape as desolation that results from proper task of man elements that also have substantial contents of memory in industrial landscapes as a time of pre-automation history and globalization of current life. Perhaps the most interesting from a theoretical point of view is precisely that quality of landscape as something external produced by the viewer in a strange time of membership, a look that is not only aesthetic but sympathetic, joyful, active concept or analytical - because there are so many ways to look as subjects - it may not be precisely defined that contemplation rather than in terms that reach one's individuality. In poetic terms, it could also be set as the set of individual gazes also create a structure that makes this landscape is valued and understood, so from that point of view that landscape is a collective creation. With respect or as a predator, man has settled in his environment and in doing so has left traces in the landscape itself that make take a certain significance. Naturally, there is a theory that distinguishes what is "home" and what is "nature" providing for the first notion of the exclusive territory in which man has no aesthetic role. I tried many times to understand this position, without understanding the approach that supports: it seems that the vision of the thing is always humane, even in the "virgin" or untouched areas, as the vision itself makes the object modified in its own perceptual unit, creating a curious indeterminacy leading to the known misunderstandings between real image and representation. Indeed, the vision of the thing requires a culture and means that the report, so that a text, a picture, a description or photograph will be humanized by the very fact of being informed, as this provides a way a priori. Thus, the landscape provides a function that sets both aspects of a potential landscape as described aspects of the landscape and can only talk about the potential of the final state of the landscape, while the landscape remains humanized by the observer himself. This question forces to choose a definition of remote landscape budgets purely cultural, so there is another way for research to contemplate that physical reality in terms of the coordinates of the man who inhabits gifted content corresponding to that revelation. Far from the positions of the geomorphology, the term "landscape" and involve a certain condition by contemplation of a subject for which the show is humanized in the act. It should also consider, in the light of the above, if it is not true that all landscapes require that humanized condition, because although they are not inhabited they are always occupied by the look that dwells, like a stage without audience produces no consistent effect. From there the coordinates where this work sets the presence of architecture in defining landscape, a premise which seems to come from the beginning given lie, because that same look is already giving the viewer a sense of order and hierarchy to contemplation, qualities that are at the basis of all architectural activity, in fact the very definition of "natural monument" - in itself a contradiction - expresses this conflict, which has a phenomenon of admiration and overlap between culture and nature as concepts faced since its inception. The conclusion on the dilemma proposed in the thesis has not been another to assume that these two realities are the culture and landscape have overlapped since the beginning of man time forming a pair. It has been said before that the process of invasion of the territory by man is significant, and that meaning is the originating autonomous creation that is isolated as an abstract concept of nature, taking them as working material, and establishing a conceptual opposition in reality and punched by the man who comes to oppose representing the closed and unknown to the enigma of the world interpreted. The question of the significance of the man on the land is subsumed in the creation of products that remain and are testimony of their own culture, so that the trace amount that the man leaves the territory contributes most to the qualification landscape as a concept. That brought into any landscape - by the mere fact of being and being well defined - is already cultural, as it is configured by culture products. The words that can be locked in the stones of the monuments or cities are those of the men who worked there, and also of those who inhabited: even more, the sense of the landscape itself and its conservation are determined by the presence of man as the sole interpreter of concepts such as ecology or conservation, something which becomes manifest also in the awful devastation that produce the phenomena of nature. The natural history, like life, are shaped by success and devastation without special preference, the preference is used for feeding on other kinds of concepts. The question of moral values attributed to the natural world is very ancient, and may be the source or the source of the first religions, an issue that joins the unfailing notion of mortality that defines the existence of man against immanence of nature. That nature is endowed intuitively an "innocent" character assuming that innocence is the opposite of wisdom. The other issue is well, since nature does not even have what is defined as "character" because that is something that serves to qualify beings, but not objects. The question does not fall clearly on the side of the definitions or qualities, but from the analysis of the reality that man is building, destroying or damaging to define the territory, interposing his way resources facilities and possible witness as the main manifestation of its essence. Among the artifacts that man produces one of the most persistent and most conspicuously disclosed is architecture as a way of modification of space and territory. The space can be modified in many ways, but in either case is one of the most characteristic traces that man establishes as a physical manifestation of his own discourse being. Architecture has also proven to be one of the most persistent phenomena, even more than their own language that originates in his speech first. The paradigm wrote in the episode described on the Tower of Babel in the Bible shows the question of ambition of men before God - represented precisely in architecture - is assimilated to the discussion about the primary language. The issue is not trivial, since the phenomenon of creation is something that is granted exclusively to the gods, for that reason inhabit the territories to which men can not reach; territories where the hostel located mythologies gods and demons, with large gaps where to place the minor deities, heroes or hybrid beings where the yoke of the gods with human subjects produces relieving sense of mortality. The commentary on Genesis also gives a value to the art, the myth of Prometheus and fire as creator of excellence. In front of promethean progress, divine value is postulated, and the only possible way to alleviate this progress is the confusion of language, because that is what will produce the dispersion and lack of agreement. The issue may also explain such a common passion for the canonical architecture maintained throughout long periods, like a great machine inertia. It seems that the main concepts of architecture based on simple elements like milestone, lintels, straight and curved stairs or ramps, or other qualified and used are granted to the stone, brick, wood or metal as the primary components of the architectural material maintained throughout many millennia are almost unchanged, as is the case with the eating habits that follow a progression through the raw, the cooked and roasted or fried until obtain different degrees of refinement, but always are based on the primal feeling. The discovery of the architecture comes from a management dimensions, and consequently the geometry. But the geometry is abstract thing like the language so that to make architecture that first absorption capacity which then allows the realization of a device is necessary. Reality and its number exhibit a divorce, like things and their names displayed his; numerical analysis is just one way of seeing reality, rigorous and accurate - though partial - only represents the ideal model to which reality is coming to a greater or lesser extent: the mathematical approach makes the universe can condense on numbers, like reality may condense on names, but neither the name nor the number will reflect in all its complexity. The number is only a means of describing things, such as the pure forms that match setup a mathematical theory that occurs anywhere in the universe. However, for the practice of architecture is necessary to go to the simplification that requires abstract view of a section plane of reality, as an abstract element considered cutting. With its trace or not, with the mathematical expression that describes what or without clarify, this intuition of the plane as a generator of space predates his own expression, like speech preceded the writing, which only occurred through it and as reinforcement and replacement of memory. There are abstractions of memory displayed on the signs of nature only on casual and fragmentary, such as line, square and circle: those initials and abstract forms located in abstraction give rise to the first signs of primordial architecture, so that squares and circles, lifting two prisms and spheroids or spherical surfaces appear in tombs and elementary buildings the first few times, and that primordial geometry overlaps the landscape in which it is inserted. It is also true that these forms are approximate objects found in the physical environment, limb lines, branches and limbs; straight in some crystals angles observed by cutting or circular in stars and craters forms, but only the approximate shape and not its abstraction, just as the hieroglyphic of a falcon to represent the idea of surveillance presents the good view, or even the image of the eye itself replace the idea of the all-seeing God. The election was resolved, after many attempts and approaches, with the adoption of the right angle as an easy trick for stake through the sacred triangle 3:4:5 already used to build the pyramids of Egypt, and also gave rise to most of the old urbanism tend coexist with the primary circular form type called "Tholo". That frame homer was one of the fill patterns of common and compact space, and that was probably the reason why in much later times was adopted as a permanent effective form of organization against the topological disorder that seeks the set of association circular plants. Another issue is that these paradigmatic and unknown primary concepts - that converge at the origin of civilizations - then become something canon, through use. The canon itself is something ideal, as a rule for objects of a reality that has been created only as an indication of the ca-non, something abstract that has strict proportions are always the same and not due to rational criteria: be absurd however seek the Greek canon among the temples of time as some did, because the buildings only approximate the canonical examples and for that reason we speak of "doric from Parthenon" which is different from Aegina or Paestum, being all clearly doric. However, this idea is useful to scholar, the architectural theorist and historian, although it reflects only a vague idea of what happens beyond the book. Another issue is the subtlety of the examples of architecture, just as the bodies of living beings are never symmetrical, even if they involve a general symmetrical design derived from the conditions of cell division, the supposedly canonical buildings where specialists were inspired to define the classical orders do not have that exact modular symmetry, but a general model adapted to the ever changing location of the site shaping the landscape in which they are inserted. The light of the various bays of the Parthenon is slightly different, but keep a clear sense of axial symmetry, so that those "orders" that formed the theory of architecture are just a beautiful sectoral interpretation of ancient architecture developed by writers of the Renaissance and later by neoclassical. It seems, however, that craving for clarity of language canon as is inherent to the development of architecture, a lingua franca that tends to avoid scattering among mortals by the ancient gods, so if it was not possible the heaven of the gods sought the language of the Earth was at least intelligible to be understood. Power structure has always required a certain level of organization, and the instructions are clearly understood: it seems that in our times these ancient canons were replaced by obedience to abstract rules, issued by institutions also somewhat abstract and have funny names made up acronym, although not well known virtue. The current canon consists of "rules" that leave some quiet, although it seems that maybe all that interweaves-do formally serving as anaesthesia for the social body also seeks the destruction of forests in forms of huge mountains of bureaucratic paper. For many centuries were other rules, in the form of a canon which no one could escape: still using royalties or without them, civilization flourished in architecture from the earliest cave shelters or shelters and the primordial reality was setting mode in landscape. As noted above, this is a return trip in which both confused and subsumed: the management of forms and languages of architecture over time would allow the distinction between the field where chaos reigns and city, where order reigns theoretically creating a divorce that lasted millennia and still persists. This opposition also generate a form of landscape and a series of symbolic and sacred uses of architectural elements - such as doors and walls - which have remained conceptually although today the cities no longer having physical walls or doors close during the night. In this sense, the architecture could define the landscape, architecture is not only understood as the buildings themselves, but the fact of the manifestation of the man on the premises, so you can not speak without his landscape architecture, the same so we can not speak of landscape without men. For this reason, the thesis discusses architecture and landscape, but more particularly to the fact of architecture in defining landscape, as the facts of architectural or not will determine the quality and qualification of a landscape. One should begin first a definition of what is understood and has been commonly understood by landscape: equally, and given the context in which it places the own thesis work, the issue only be limited to what is understood as western culture, for the development of civilization always has a local colour that makes the analysis of a phenomenon of this magnitude have different connotations in different areas of civilization. Similarly, and given also that the landscape is constructed through all cultural manifestations, will sometimes necessary to investigate other non-architectural disciplines to understand the scope of some cases in which the architectural remains have disappeared, or the remaining few traces. Such a broad definition of architecture take to write a story about all of Western culture and for this reason only been sketched ideas about the appearance of these signs on the landscape based on ancient and primitive elements are repeated insistently and leading the varied repertoire of Western architecture shaping ideas about how the media and the world is perceived and inhabited.