Evaluation of APD and SiPM Matrices as Sensors for Monolithic PET Detector Block

Gamma detectors based on monolithic scintillator blocks coupled to APDs matrices have proved to be a good alternative to pixelated ones for PET scanners. They provide comparable spatial resolution, improve the sensitivity and make easier the mechanical design of the system. In this study we evaluate by means of Geant4-based simulations the possibility of replacing the APDs by SiPMs. Several commercial matrices of light sensors coupled to LYSO:Ce monolithic blocks have been simulated and compared. Regarding the spatial resolution and linearity of the detector, SiPMs with high photo detection efficiency could become an advantageous replacement for the APDs

Evaluation of a PET Prototype Using LYSO:Ce Monolithic Detector Block

We have analyzed the performance of a PET demonstrator formed by two sectors of four monolithic detector blocks placed face-to-face. Both front-end and read-out electronics have been evaluated by means of coincidence measurements using a rotating 22Na source placed at the center of the sectors in order to emulate the behavior of a complete full ring. A continuous training method based on neural network (NN) algorithms has been carried out to determine the entrance points over the surface of the detectors. Reconstructed images from 1 MBq 22Na point source and 22Na Derenzo phantom have been obtained using both filtered back projection (FBP) analytic methods and the OSEM 3D iterative algorithm available in the STIR software package [1]. Preliminary data on image reconstruction from a 22Na point source with Ø = 0.25 mm show spatial resolutions from 1.7 to 2.1 mm FWHM in the transverse plane. The results confirm the viability of this design for the development of a full-ring brain PET scanner compatible with magnetic resonance imaging for human studies.

Characterization and Test of a Data Acquisition System for PET

A small Positron Emission Tomography demonstrator based on LYSO slabs and Silicon Photomultiplier matrices is under construction at the University and INFN of Pisa. In this paper we present the characterization results of the read-out electronics and of the detection system. Two SiPM matrices, composed by 8 × 8 SiPM pixels, 1.5 mm pitch, have been coupled one to one to a LYSO crystals array. Custom Front-End ASICs were used to read the 64 channels of each matrix. Data from each Front-End were multiplexed and sent to a DAQ board for the digital conversion; a motherboard collects the data and communicates with a host computer through a USB port. Specific tests were carried out on the system in order to assess its performance. Futhermore we have measured some of the most important parameters of the system for PET application.

Projector Model for Efficient List-Mode Reconstruction in PET Scanners with Parallel Planar Detectors

We have developed a new projector model specifically tailored for fast list-mode tomographic reconstructions in Positron emission tomography (PET) scanners with parallel planar detectors. The model provides an accurate estimation of the probability distribution of coincidence events defined by pairs of scintillating crystals. This distribution is parameterized with 2D elliptical Gaussian functions defined in planes perpendicular to the main axis of the tube of response (TOR). The parameters of these Gaussian functions have been obtained by fitting Monte Carlo simulations that include positron range, acolinearity of gamma rays, as well as detector attenuation and scatter effects. The proposed model has been applied efficiently to list-mode reconstruction algorithms. Evaluation with Monte Carlo simulations over a rotating high resolution PET scanner indicates that this model allows to obtain better recovery to noise ratio in OSEM (ordered-subsets, expectation-maximization) reconstruction, if compared to list-mode reconstruction with symmetric circular Gaussian TOR model, and histogram-based OSEM with precalculated system matrix using Monte Carlo simulated models and symmetries.

Silicon Photomultipliers (SiPM) as novel photodetectors for PET

Next generation PET scanners should fulfill very high requirements in terms of spatial, energy and timing resolution. Modern scanner performances are inherently limited by the use of standard photomultiplier tubes. The use of Silicon Photomultipliers (SiPMs) is proposed for the construction of a 4D-PET module of 4.8×4.8 cm2 aimed to replace the standard PMT based PET block detector. The module will be based on a LYSO continuous crystal read on two faces by Silicon Photomultipliers. A high granularity detection surface made by SiPM matrices of 1.5 mm pitch will be used for the x–y photon hit position determination with submillimetric accuracy, while a low granularity surface constituted by 16 mm2 SiPM pixels will provide the fast timing information (t) that will be used to implement the Time of Flight technique (TOF). The spatial information collected by the two detector layers will be combined in order to measure the Depth of Interaction (DOI) of each event (z). The use of large area multi-pixel Silicon Photomultiplier (SiPM) detectors requires the development of a multichannel Data Acquisition system (DAQ) as well as of a dedicated front-end in order not to degrade the intrinsic detector capabilities and to manage many channels. The paper describes the progress made on the development of the proof of principle module under construction at the University of Pisa.

Efficient methodologies for system matrix modelling in iterative image reconstruction for rotating high-resolution PET

A fully 3D iterative image reconstruction algorithm has been developed for high-resolution PET cameras composed of pixelated scintillator crystal arrays and rotating planar detectors, based on the ordered subsets approach. The associated system matrix is precalculated with Monte Carlo methods that incorporate physical effects not included in analytical models, such as positron range effects and interaction of the incident gammas with the scintillator material. Custom Monte Carlo methodologies have been developed and optimized for modelling of system matrices for fast iterative image reconstruction adapted to specific scanner geometries, without redundant calculations. According to the methodology proposed here, only one-eighth of the voxels within two central transaxial slices need to be modelled in detail. The rest of the system matrix elements can be obtained with the aid of axial symmetries and redundancies, as well as in-plane symmetries within transaxial slices. Sparse matrix techniques for the non-zero system matrix elements are employed, allowing for fast execution of the image reconstruction process. This 3D image reconstruction scheme has been compared in terms of image quality to a 2D fast implementation of the OSEM algorithm combined with Fourier rebinning approaches. This work confirms the superiority of fully 3D OSEM in terms of spatial resolution, contrast recovery and noise reduction as compared to conventional 2D approaches based on rebinning schemes. At the same time it demonstrates that fully 3D methodologies can be efficiently applied to the image reconstruction problem for high-resolution rotational PET cameras by applying accurate pre-calculated system models and taking advantage of the system's symmetries.

Limiting properties in the characterisation of mixed recycled aggregates for use in the manufacture of concrete

El objetivo principal de este trabajo de investigación es estudiar las propiedades del árido reciclado mixto para la fabricación de hormigón reciclado en aplicaciones no estructurales. Se ha realizado la caracterización completa de 35 muestras de áridos reciclados mixtos gruesos de distinta calidad, procedentes de 13 plantas de tratamiento diferentes de la geografía española. Se han estudiado las correlaciones que existen entre las diferentes propiedades, en particular, con la absorción de agua, el contenido de sulfatos y la composición. Se propone una clasificación de los áridos reciclados y se limita de forma indicativa el contenido de yeso para que una muestra de árido reciclado mixto cumpla con la limitación del 0,8% de los sulfatos solubles en ácido de la Instrucción EHE-08. Recycling of construction and demolition waste (CDW) has become a widespread concern in Spain for the last years, as a way to preserve natural resources and achieve a better control of waste disposal sites.Specific applications which make use of mixed recycled aggregates are of great importance, as this types of aggregates constitute the majority of the total production. Structural and non-structural concrete is one of the possible applications, being this the main goal of our study. This paper presents a study on the physical and chemical characteristics of mixed recycled aggregates which have been obtained from different CDW treatment plants of Spain. Correlations between the different properties were investigated in order to find criterions of acceptance for recycled aggregates to be used in concrete. The comparison between the properties offers the possibility of pre-selecting a great quantity of mixed recycled aggregates, these being suitable for either structural and non-structural concrete. The determination of water absorption and the gypsum content are good indicators in order to evaluate the quality of the mixed recycled aggregates for its application in the production of concrete.

Timing performances of a data acquisition system for time of flight PET

We are investigating the performances of a data acquisition system for Time of Flight PET, based on LYSO crystal slabs and 64 channels Silicon Photomultipliers matrices (1.2 cm2 of active area each). Measurements have been performed to test the timing capability of the detection system (SiPM matices coupled to a LYSO slab and the read-out electronics) with both test signal and radioactive source.

Construction elements made with recycled plastics

Ponencia sobre elementos constructivos elaborados con materiales reciclados

Crack width control in RC elements with recycled steel fibres and applications to integral structures : theoretical and experimental study

El presente trabajo trata de elementos reforzados con barras de armadura y Fibras Metálicas Recicladas (FMR). El objetivo principal es mejorar el comportamiento a fisuración de elementos sometidos a flexión pura y a flexión compuesta, aumentando en consecuencia las prestaciones en servicio de aquellas estructuras con requerimientos estrictos con respecto al control de fisuración. Entre éstas últimas se encuentran las estructuras integrales, es decir aquellas estructuras sin juntas (puentes o edificios), sometidas a cargas gravitatorias y deformaciones impuestas en los elementos horizontales debidas a retracción, fluencia y temperatura. Las FMR son obtenidas a partir de los neumáticos fuera de uso, y puesto que el procedimiento de reciclado se centra en el caucho en vez que en el acero, su forma es aleatoria y con longitud variable. A pesar de que la eficacia del fibrorefuerzo mediante FMR ha sido demostrada en investigaciones anteriores, la innovación que representa este trabajo consiste en proponer la acción combinada de barras convencionales y FMR en la mejora del comportamiento a fisuración. El objetivo es por tanto mejorar la sostenibilidad del proyecto de la estructura en HA al utilizar materiales reciclados por un lado, y aumentando por el otro la durabilidad. En primer lugar, se presenta el estado del arte con respecto a la fisuración en elementos de HA, que sucesivamente se amplía a elementos reforzados con barras y fibras. Asimismo, se resume el método simplificado para el análisis de columnas de estructuras sin juntas ya propuesto por Pérez et al., con particular énfasis en aquellos aspectos que son incompatibles con la acción de las fibras a nivel seccional. A continuación, se presenta un modelo para describir la deformabilidad seccional y la fisuración en elementos en HA, que luego se amplía a aquellos elementos reforzados con barras y fibras, teniendo en cuenta también los efectos debidos a la retracción (tension stiffening negativo). El modelo es luego empleado para ampliar el método simplificado para el análisis de columnas. La aportación consiste por tanto en contar con una metodología amplia de análisis para este tipo de elementos. Seguidamente, se presenta la campaña experimental preliminar que ha involucrado vigas a escala reducida sometidas a flexión simple, con el objetivo de validar la eficiencia y la usabilidad en el hormigón de las FMR de dos diferentes tipos, y su comportamiento con respecto a fibras de acero comerciales. Se describe a continuación la campaña principal, consistente en ensayos sobre ocho vigas en flexión simple a escala 1:1 (variando contenido en FRM, Ø/s,eff y recubrimiento) y doce columnas a flexión compuesta (variando contenido en FMR, Ø/s,eff y nivel de fuerza axil). Los resultados obtenidos en la campaña principal son presentados y comentados, resaltando las mejoras obtenidas en el comportamiento a fisuración de las vigas y columnas, y la rigidez estructural de las columnas. Estos resultados se comparan con las predicciones del modelo propuesto. Los principales parámetros estudiados para describir la fisuración y el comportamiento seccional de las vigas son: la separación entre fisuras, el alargamiento medio de las armaduras y la abertura de fisura, mientras que en los ensayos de las columnas se ha contrastado las leyes momento/curvatura, la tensión en las barras de armadura y la abertura de fisura en el empotramiento en la base. La comparación muestra un buen acuerdo entre las predicciones y los resultados experimentales. Asimismo, se nota la mejora en el comportamiento a fisuración debido a la incorporación de FMR en aquellos elementos con cuantías de armadura bajas en flexión simple, en elementos con axiles bajos y para el control de la fisuración en elementos con grandes recubrimientos, siendo por tanto resultados de inmediato impacto en la práctica ingenieril (diseño de losas, tanques, estructuras integrales, etc.). VIIIComo punto final, se presentan aplicaciones de las FMR en estructuras reales. Se discuten dos casos de elementos sometidos a flexión pura, en particular una viga simplemente apoyada y un tanque para el tratamiento de agua. En ambos casos la adicción de FMR al hormigón lleva a mejoras en el comportamiento a fisuración. Luego, utilizando el método simplificado para el análisis en servicio de columnas de estructuras sin juntas, se calcula la máxima longitud admisible en casos típicos de puentes y edificación. En particular, se demuestra que las limitaciones de la práctica ingenieril actual (sobre todo en edificación) pueden ser aumentadas considerando el comportamiento real de las columnas en HA. Finalmente, los mismos casos son modificados para considerar el uso de MFR, y se presentan las mejoras tanto en la máxima longitud admisible como en la abertura de fisura para una longitud y deformación impuesta. This work deals with elements reinforced with both rebars and Recycled Steel Fibres (RSFs). Its main objective is to improve cracking behaviour of elements subjected to pure bending and bending and axial force, resulting in better serviceability conditions for these structures demanding keen crack width control. Among these structures a particularly interesting type are the so-called integral structures, i.e. long jointless structures (bridges and buildings) subjected to gravitational loads and imposed deformations due to shrinkage, creep and temperature. RSFs are obtained from End of Life Tyres, and due to the recycling process that is focused on the rubber rather than on the steel they come out crooked and with variable length. Although the effectiveness of RSFs had already been proven by previous research, the innovation of this work consists in the proposing the combined action of conventional rebars and RSFs to improve cracking behaviour. Therefore, the objective is to improve the sustainability of RC structures by, on the one hand, using recycled materials, and on the other improving their durability. A state of the art on cracking in RC elements is firstly drawn. It is then expanded to elements reinforced with both rebars and fibres (R/FRC elements). Finally, the simplified method for analysis of columns of long jointless structures already proposed by Pérez et al. is resumed, with a special focus on the points that conflict when taking into account the action of fibres. Afterwards, a model to describe sectional deformability and cracking of R/FRC elements is presented, taking also into account the effect of shrinkage (negative tension stiffening). The model is then used to implement the simplified method for columns. The novelty represented by this is that a comprehensive methodology to analyse this type of elements is presented. A preliminary experimental campaign consisting in small beams subjected to pure bending is described, with the objective of validating the effectiveness and usability in concrete of RSFs of two different types, and their behaviour when compared with commercial steel fibres. With the results and lessons learnt from this campaign in mind, the main experimental campaign is then described, consisting in cracking tests of eight unscaled beams in pure bending (varying RSF content, Ø/s,eff and concrete cover) and twelve columns subjected to imposed displacement and axial force (varying RSF content, Ø/s,eff and squashing load ratio). The results obtained from the main campaign are presented and discussed, with particular focus on the improvement in cracking behaviour for the beams and columns, and structural stiffness for the columns. They are then compared with the proposed model. The main parameters studied to describe cracking and sectional behaviours of the beam tests are crack spacing, mean steel strain and crack width, while for the column tests these were moment/curvature, stress in rebars and crack with at column embedment. The comparison showed satisfactory agreement between experimental results and model predictions. Moreover, it is pointed out the improvement in cracking behaviour due to the addition of RSF for elements with low reinforcement ratios, elements with low squashing load ratios and for crack width control of elements with large concrete covers, thus representing results with a immediate impact in engineering practice (slab design, tanks, integral structures, etc.). Applications of RSF to actual structures are finally presented. Two cases of elements in pure bending are presented, namely a simple supported beam and a water treatment tank. In both cases the addition of RSF to concrete leads to improvements in cracking behaviour. Then, using the simplified model for the serviceability analysis of columns of jointless structures, the maximum achievable jointless length of typical cases of a bridge and building is obtained. In XIIparticular, it is shown how the limitations of current engineering practice (this is especially the case of buildings) can be increased by considering the actual behaviour of RC supports. Then, the same cases are modified considering the use of RSF, and the improvements both in maximum achievable length and in crack width for a given length and imposed strain at the deck/first floor are shown.

Proof of concept of an imaging system demonstrator for PET applications with SiPM

A PET imaging system demonstrator based on LYSO crystal arrays coupled to SiPM matrices is under construction at the University and INFN of Pisa. Two SiPM matrices, composed of 8×8 SiPM pixels, and 1,5 mm pitch, have been coupled one to one to a LYSO crystals array and read out by a custom electronics system. front-end ASICs were used to read 8 channels of each matrix. Data from each front-end were multiplexed and sent to a DAQ board for the digital conversion; a motherboard collects the data and communicates with a host computer through a USB port for the storage and off-line data processing. In this paper we show the first preliminary tomographic image of a point-like radioactive source acquired with part of the two detection heads in time coincidence.

A new PET prototype for proton therapy: comparison of data and Monte Carlo simulations

Ion beam therapy is a valuable method for the treatment of deep-seated and radio-resistant tumors thanks to the favorable depth-dose distribution characterized by the Bragg peak. Hadrontherapy facilities take advantage of the specific ion range, resulting in a highly conformal dose in the target volume, while the dose in critical organs is reduced as compared to photon therapy. The necessity to monitor the delivery precision, i.e. the ion range, is unquestionable, thus different approaches have been investigated, such as the detection of prompt photons or annihilation photons of positron emitter nuclei created during the therapeutic treatment. Based on the measurement of the induced β+ activity, our group has developed various in-beam PET prototypes: the one under test is composed by two planar detector heads, each one consisting of four modules with a total active area of 10 × 10 cm2. A single detector module is made of a LYSO crystal matrix coupled to a position sensitive photomultiplier and is read-out by dedicated frontend electronics. A preliminary data taking was performed at the Italian National Centre for Oncological Hadron Therapy (CNAO, Pavia), using proton beams in the energy range of 93–112 MeV impinging on a plastic phantom. The measured activity profiles are presented and compared with the simulated ones based on the Monte Carlo FLUKA package.

Thermal and mechanical properties of recycled poly(Lactic acid)

Biodegradable polymers have experienced increased attention in recent years because of their wide range of applications in biomedical, packaging and agriculture fields. PLA, poly(lactic acid), is a linear aliphatic biodegradable thermoplastic polyester, with good mechanical properties, thermal stability, processability and low environmental impact, widely used as an alternative to conventional polymers. PLA products can be recycled after use either by remelting and reprocessing the material, or by hydrolysis to basic lactic acid [1]. The object of this communication is the study of the possible variation in physical properties induced by sub sequent reprocessing cycles of PLA.

Estrategias de desarrollo sostenible de la arquitectura del oasis de M’hamid, desierto del Sahara

Esta investigación se plantea con la hipótesis radical de cómo habitar el desierto de forma sostenible, desde una actitud pragmática y experimental basada en el progreso. La justificación se basa en primer lugar en los 2.000 millones de personas en el mundo que viven en entornos desérticos, el 80% de ellas, en países en desarrollo, porque el 40% de la superficie terrestre está bajo amenaza de desertificación afectando al 37% de la población mundial, con 12 millones de hectáreas al año perdidas por esa causa, y por último, porque se considera el desierto como un entorno de gran atractivo y potencial. El contenido de la investigación se estructura en tres movimientos: posicionamiento, mirada y acción: Desde el posicionamiento se define en primer lugar la sostenibilidad, aportando un nuevo diagrama donde se incorpora el ámbito arquitectónico como uno de los pilares principales, y, posteriormente, se establecen los criterios de evaluación de la sostenibilidad, aportando un sistema de indicadores donde se incorporan parámetros adecuados a las circunstancias del oasis. Del mismo modo, se estudian y analizan metodologías de actuación y proyectos de desarrollo sostenible existentes que enmarcan el estado del arte, constatando la dificultad de adaptación de los mismos a las condiciones de los oasis, por lo que se elabora una metodología propia donde se modifica la dinámica estratégica, de forma que el impulso se plantea desde la acción social, a través de hipótesis de estrategias basadas en sistemas low-cost, autoconstruidas, asumibles económicamente y de implantación factible. El caso de estudio específico radica en la situación extrema de las condiciones en el oasis de M’hamid, donde se evidencia un proceso de desintegración y abandono. Esto es debido a una acumulación de circunstancias externas e internas, de múltiples factores: naturales y antrópicos que afectan al oasis, llevando al extremo las condiciones climáticas y la escasez de recursos, naturales y artificiales. Factores como el cambio climático, la sequía, los cambios en las políticas del agua, la amenaza de desertificación, los conflictos sociales, el desequilibrio ecológico, la escasez económica, la crisis energética, la obsolescencia arquitectónica, el patrimonio construido prácticamente destruido, y la malentendida nueva arquitectura. Es importante constatar la escasa documentación gráfica existente sobre la zona de actuación lo que ha conllevado un amplio trabajo de documentación, tanto cartográfica como de observación directa, aportada a la tesis como investigación de elaboración propia. La mirada analítica al caso de estudio permite conocer los recursos disponibles y las potencialidades latentes del oasis de M’hamid, que permitirán actuar para subvertir la dinámica involutiva imperante, de forma que los dibujos iniciales de apropiación contextual y análisis críticos derivan en mapas de acción diagramados conformados por un sistema de objetos y la definición de estrategias transversales, deconstruyendo el pasado y reconstruyendo el futuro, incorporando sistemas alternativos que se definen en 7 líneas estratégicas de acción formuladas desde los 3 ámbitos relacionados con el ecosistema: ecológico, socio- económico y arquitectónico. Así, la tesis defiende la acción arquitectónica como impulsora del desarrollo sostenible, apoyada en 3 elementos: - la creación de objetos “tecnoartesanos”, para el aprovechamiento de los recursos energéticos - las transformaciones arquitectónicas, para reformular el hábitat desde la eficiencia energética y el progreso - y el impulso de acciones cotidianas, que redefinan las relaciones sociales, creando entornos cooperativos y colaborativos. En el ámbito ecológico se proponen actuaciones anti desertificación mediante incubadoras de árboles; sistemas alternativos de gestión del agua, como la lluvia sólida; estrategias de potenciación de la producción agrícola; la construcción de mecanismos de obtención de energía a partir de residuos, como los paneles solares con botellas PET. En el ámbito socioeconómico se plantean nuevas formas de acción social y de reactivación económica. Por último, en el ámbito urbano-arquitectónico, se incorporan modificaciones morfológicas a la arquitectura existente y una relectura contemporánea de la tierra, como material que permite nuevas geometrías, obteniendo arena petrificada por procesos microbiológicos, y potenciando la tierra como recurso artístico. Esta tesis es un punto de partida, recoge sistemas, estrategias y experiencias, para funcionar como un estímulo o impulso dinamizador del futuro desarrollo sostenible del oasis, abriendo vías de investigación y experimentación. ABSTRACT This research puts forth the radical hypothesis of how to inhabit the desert in a sustainable way, using a pragmatic and experimental approach based on progress. The justification for this resides in the fact that there are 2,000 million people in the world living in desert environments, 80% of them in developing countries. Forty percent of the earth’s surface is under threat of desertification, affecting 37% of the world population and with 12 million hectares being lost each year. And finally, the desert is considered as an attractive environment and therefore, with great potential. The content of the research is structured in three main sections: positioning, observation and action: As a point of departure, sustainability is defined, proposing a new framework where architecture is incorporated as one of the main pillars. Then, the criteria for evaluating sustainability are established. These provide a system of indicators, which incorporate parameters based on the specific circumstances of the oasis. Methodologies and existing sustainable development projects that represent the state-of-the-art are analyzed, discussing the difficulty of adapting them to conditions of oases. A methodology that modifies strategic concepts is developed, whereby the catalyst is social action, and strategies are developed based on low-cost, self-built, and feasible implementation systems. The specific case study lies in the extreme conditions in the oasis of M'hamid, where a process of decay and neglect is evident. This deterioration is due to an accumulation of external and internal circumstances, and of natural and anthropogenic factors that affect the oasis, leading to extreme weather conditions and a shortage of both natural and artificial resources. Factors include; climate change, drought, changes in water policies, the threat of desertification, social conflicts, ecological imbalance, economic shortage, the energy crisis, architectural obsolescence, destruction of built heritage, and misunderstood new architecture. It is important to note the extremely limited graphic information about the area has led me to produce an extensive archive of maps and drawings, many developed by direct observation, that contribute to the research. The case study analysis of the oasis of M'hamid examines the resources available and the latent potential to slow the prevailing trend towards deterioration. The initial drawings of contextual appropriation and critical analysis result in maps and diagrams of action, which are formed by a system of objects and the definition of strategies. These can be thought of as understanding or “deconstructing” the past to reconstruct the future. Alternative approaches defined in seven strategies for action are based on three fields related to the ecosystem: ecological, socioeconomic and architectural. Thus, the thesis defends architectural action to promote sustainable development, based on three elements: - The creation of "techno-artisans", to make use of energy resources - Architectural changes, to reformulate habitat in terms of energy efficiency and progress - And the promotion of everyday actions, to redefine social relations, creating cooperative and collaborative environments. In the ecological field, I propose anti-desertification actions such as; tree incubators, alternative water management systems(such as solid rain),; strategies to empower the agricultural production, energy from low-cost systems made out from recycled materials(such as solar panels from PET bottles or wind turbine from bicycle wheels). In the socioeconomic sphere, I propose to implement new forms of social action and economic regeneration. Finally, within the urban and architectural field, I propose morphological changes to the existing architecture and a contemporary reinterpretation of the earth as a material that allows new geometries, creating petrified sand by microbiological processes or enhancing nature as an artistic and energy resource. This thesis is a starting point. It collects systems, strategies and experiences to serve as a stimulus or dynamic momentum for future sustainable development of the oasis, opening new avenues of research and experimentation. RÉSUMÉ Cette recherche part d'une hypothèse radicale : comment habiter le désert de façon durable, et ce à partir d'une approche pragmatique et expérimentale basée sur le progrès. Cette hypothèse se justifie en raison des 2 milliards de personnes qui dans le monde habitent des environnements désertiques, 80% d'entre eux dans des pays en voie de développement, mais aussi parce que 40% de la surface de la planète est sous menace de désertification, un phénomène affectant 37% de la population mondiale et qui cause la perte de 12 millions d'hectares par an; et enfin parce que le désert est considéré comme un environnement très attrayant et fort d’un grand potentiel. Le contenu de la recherche se divise en trois mouvements: le positionnement, le regard et l'action : Du point de vue du positionnement on définit tout d'abord la durabilité, présentant un nouveau schéma où le domaine de l'architecture devient un des principaux piliers, et, par la suite, des critères d'évaluation de la durabilité sont établis, en fournissant un système d’indicateurs qui intègre les paramètres appropriés aux circonstances de l'oasis. De même, des méthodologies et des projets de développement durable existants sont étudiés et analysés, ce qui encadre l'état de l'art, remarquant la difficulté de les adapter aux conditions des oasis. De cette difficulté découle l'élaboration d'une méthodologie qui modifie la dynamique stratégique, de sorte que l'impulsion provient de l'action sociale, à travers des hypothèses de stratégie basées sur des systèmes low-cost, auto-construits, et de mise en oeuvre économiquement viable. Le cas d'étude spécifique réside en la situation extrême des conditions de l'oasis de M’hamid, où un processus de décadence et de négligence est évident. Cela est dû à une accumulation de circonstances externes et internes, de multiples facteurs: les facteurs naturels et anthropiques qui affectent l'oasis, menant à l'extrême les conditions météorologiques et la pénurie de ressources, autant naturelles qu'artificielles. Des facteurs tels que le changement climatique, la sécheresse, les changements dans les politiques de l'eau, la menace de la désertification, les conflits sociaux, le déséquilibre écologique, la pénurie économique, la crise de l'énergie, l'obsolescence architecturale, le patrimoine bâti pratiquement détruit et une mauvais compréhensif de la nouvelle architecture. Il est important de de faire remarquer le peu d'informations graphiques du domaine d'action, ce qui a conduit à un vaste travail de documentation, autant cartographique que relative à l'observation directe. Cette documentation s'ajoute à la thèse en tant que recherche propre. Le regard analytique sur le cas d'étude permet de connaître les ressources disponibles et le potentiel latent de l'oasis de M’hamid, qui agiront pour renverser la dynamique d'involution en vigueur. Ainsi, les premiers dessins d'appropriation contextuelle et analyse critique deviennent des cartes d'action schématisées formées par un système d'objets et la définition de stratégies transversales, qui déconstruisent le passé et reconstruisent l'avenir, en incorporant des systèmes alternatifs qui se définissent sur 7 lignes stratégiques d'action formulées à partir des 3 domaines en relation avec l’écosystème: l’écologique, le socio-économique et l'architectural. Ainsi, la thèse défend l'action architecturale en tant que promotrice du développement durable, et ce basé sur 3 éléments: - la création d'objets "technoartisans" pour l'exploitation des ressources énergétiques - les modifications architecturales, pour reformuler l'habitat du point de vue de l'efficacité énergétique et le progrès - et la promotion des actions quotidiennes, pour redéfinir les relations sociales, et la création d'environnements de coopération et collaboration. Dans le domaine de l'écologie des actions de lutte contre la désertification sont proposées à travers des pépinières d'arbres, des systèmes alternatifs de gestion de l'eau comme par exemple la pluie solide, des stratégies de mise en valeur de la production agricole, la construction de mécanismes de production d'énergie à partir de résidus, tels que les panneaux solaires ou les bouteilles en PET. Dans le domaine socio-économique, l'on propose de nouvelles formes d'action sociale et de reprise économique. Enfin, dans le domaine de l'urbain et de l'architectural, on incorpore des changements morphologiques à l'architecture existante et une relecture contemporaine de la terre, comme matériau qui permet de nouvelles géométries, en obtenant du sable pétrifié par des procédés microbiologiques et en mettant en valeur la terre comme une ressource artistique. Cette thèse n'est qu'un point de départ. Elle recueille des systèmes, des stratégies et des expériences pour servir de stimulus ou d'impulsion dynamisatrice du futur développement durable de l'oasis, en ouvrant des voies de recherche et d'expérimentation.