Band gap control via tuning of inversion degree in CdIn2S4 spinel

Based on theoretical arguments, we propose a possible route for controlling the band-gap in the promising photovoltaic material CdIn2S4. Our ab initio calculations show that the experimental degree of inversion in this spinel (fraction of tetrahedral sites occupied by In) corresponds approximately to the equilibrium value given by the minimum of the theoretical inversion free energy at a typical synthesis temperature. Modification of this temperature, or of the cooling rate after synthesis, is then expected to change the inversion degree, which in turn sensitively tunes the electronic band-gap of the solid, as shown here by screened hybrid functional calculations.

Electronic properties of doped magnesium thioindate ternary spinel in the normal and in the inverse structure

We present a theoretical study of the structural and electronic properties of the M-doped MgIn2S4 ternary spinel semiconductor with M = V, Cr, and Mn. All substitutions, in the normal and in the inverse structure, are analyzed. Some of these possible substitutions present intermediate-band states in the band gap with a different occupation for a spin component. It increases the possibilities of inter-band transitions and could be interesting for applications in optoelectronic devices. The contribution to, and the electronic configuration of, these intermediate bands for the octahedral and tetrahedral sites is analyzed and discussed. The study of the substitutional energies indicates that these substitutions are favorable. Comparison between the pure and doped hosts absorption coefficients shows that this deeper band opens up more photon absorption channels and could therefore increase the solar-light absorption with respect to the host.

A novel topology control approach to maintain the node degree in dynamic wireless sensor networks

Topology control is an important technique to improve the connectivity and the reliability of Wireless Sensor Networks (WSNs) by means of adjusting the communication range of wireless sensor nodes. In this paper, a novel Fuzzy-logic Topology Control (FTC) is proposed to achieve any desired average node degree by adaptively changing communication range, thus improving the network connectivity, which is the main target of FTC. FTC is a fully localized control algorithm, and does not rely on location information of neighbors. Instead of designing membership functions and if-then rules for fuzzy-logic controller, FTC is constructed from the training data set to facilitate the design process. FTC is proved to be accurate, stable and has short settling time. In order to compare it with other representative localized algorithms (NONE, FLSS, k-Neighbor and LTRT), FTC is evaluated through extensive simulations. The simulation results show that: firstly, similar to k-Neighbor algorithm, FTC is the best to achieve the desired average node degree as node density varies; secondly, FTC is comparable to FLSS and k-Neighbor in terms of energy-efficiency, but is better than LTRT and NONE; thirdly, FTC has the lowest average maximum communication range than other algorithms, which indicates that the most energy-consuming node in the network consumes the lowest power.

Nonlinear normal modes in mechanical systems: concept and computation with numerical continuation

The purpose of this Project is, first and foremost, to disclose the topic of nonlinear vibrations and oscillations in mechanical systems and, namely, nonlinear normal modes NNMs to a greater audience of researchers and technicians. To do so, first of all, the dynamical behavior and properties of nonlinear mechanical systems is outlined from the analysis of a pair of exemplary models with the harmonic balanced method. The conclusions drawn are contrasted with the Linear Vibration Theory. Then, it is argued how the nonlinear normal modes could, in spite of their limitations, predict the frequency response of a mechanical system. After discussing those introductory concepts, I present a Matlab package called 'NNMcont' developed by a group of researchers from the University of Liege. This package allows the analysis of nonlinear normal modes of vibration in a range of mechanical systems as extensions of the linear modes. This package relies on numerical methods and a 'continuation algorithm' for the computation of the nonlinear normal modes of a conservative mechanical system. In order to prove its functionality, a two degrees of freedom mechanical system with elastic nonlinearities is analized. This model comprises a mass suspended on a foundation by means of a spring-viscous damper mechanism -analogous to a very simplified model of most suspended structures and machines- that has attached a mass damper as a passive vibration control system. The results of the computation are displayed on frequency energy plots showing the NNMs branches along with modal curves and time-series plots for each normal mode. Finally, a critical analysis of the results obtained is carried out with an eye on devising what they can tell the researcher about the dynamical properties of the system.

Labor risk prevention culture encouragement among students from building degree in the Technical University of Madrid

The influence of training in labor risk prevention and the development of the resulting pre-emptive culture are analyzed within this paper. In order to achieve this, a quantitative analysis of the students of Building Degree in the Technic University of Madrid has been developed. This study has been made in all grades, valuating the previous knowledge acquired during compulsory education. It must be kept in mind that the students in 3rd and 4th grade have received general and specific compulsory training in prevention and safety in the building sector.

Evaluation of the In desorption during the capped process in diluted nitride In(Ga)As quantum dots

Diluted nitride self-assembled In(Ga)AsN quantum dots (QDs) grown on GaAs substrates are potential candidates to emit in the windows of maximum transmittance for optical fibres (1.3-1.55 μm). In this paper, we analyse the effect of nitrogen addition on the indium desorption occurring during the capping process of InxGa1−xAs QDs (x = l and 0.7). The samples have been grown by molecular beam epitaxy and studied through transmission electron microscopy (TEM) and photoluminescence techniques. The composition distribution inside the dots was determined by statistical moiré analysis and measured by energy dispersive X-ray spectroscopy. First, the addition of nitrogen in In(Ga)As QDs gave rise to a strong redshift in the emission peak, together with a large loss of intensity and monochromaticity. Moreover, these samples showed changes in the QDs morphology as well as an increase in the density of defects. The statistical compositional analysis displayed a normal distribution in InAs QDs with an average In content of 0.7. Nevertheless, the addition of Ga and/or N leads to a bimodal distribution of the Indium content with two separated QD populations. We suggest that the nitrogen incorporation enhances the indium fixation inside the QDs where the indium/gallium ratio plays an important role in this process. The strong redshift observed in the PL should be explained not only by the N incorporation but also by the higher In content inside the QDs

Considerations on the success rate in aeronautical engineering studies in Spain

The relationship between different learning evaluation methods and the academic success in an aeronautical engineering degree in Spain is analysed. The study is based on data about the evolution of academic achievement obtained along the last ten year, along which the evaluation and learning’s methods have suffered huge changes.

Absorción acústica a incidencia normal de espumas de aluminio

En este artículo se presentan los primeros resultados de absorción acústica a incidencia normal de espumas de aluminio fabricadas mediante una técnica pulvimetalúrgica. El interés de estas espumas radica en que en ellas se combinan interesantes propiedades acústicas y mecánicas. Se estudian espumas de aluminio de distinta morfología superficial conseguida variando el tipo de precursor y usando materiales de relleno durante el proceso de espumación. Se muestra un estudio comparativo de las espumas fabricadas mediante esta técnica con las espumas comerciales ALPORAS. Las espumas de menor densidad presentan una absorción acústica comparable a la de las comerciales ALPORAS. ABSTRACT. In this paper, the first experimental data of acoustic absorption at normal incidence in aluminum foams generated by a metallurgic technique are presented. The interest of this kind of structures is due to the combination of mechanical and acoustic properties. By changing the precursor type or using filling materials during the foaming process, we have obtained aluminum foams with different surface morphologies. A comparative study between foams fabricated using this technique and ALPORAS commercial aluminum foams is shown. The foams which present the lower density show an acoustic absorption comparable to the ALPORAS commercial ones.

Active learning and generic competences in an operating systems course

The Bologna Declaration and the implementation of the European Higher Education Area are promoting the use of active learning methodologies. The aim of this study is to evaluate the effects obtained after applying active learning methodologies to the achievement of generic competences as well as to the academic performance. This study has been carried out at the Universidad Politécnica de Madrid, where these methodologies have been applied to the Operating Systems I subject of the degree in Technical Engineering in Computer Systems. The fundamental hypothesis tested was whether the implementation of active learning methodologies (cooperative learning and problem based learning) favours the achievement of certain generic competences (‘teamwork’ and ‘planning and time management’) and also whether this fact improved the academic performance of our students. The original approach of this work consists in using psychometric tests to measure the degree of acquired student’s generic competences instead of using opinion surveys, as usual. Results indicated that active learning methodologies improve the academic performance when compared to the traditional lecture/discussion method, according to the success rate obtained. These methods seem to have as well an effect on the teamwork competence (the perception of the behaviour of the other members in the group) but not on the perception of each students’ behaviour. Active learning does not produce any significant change in the generic competence ‘planning and time management'.

A Coordinated Plan for Teaching Software Engineering in the University Rey Juan Carlos.

Un plan para organizar las enseñanzas de la ingeniería del software en las titulaciones de informática de la URJC. Nowadays both industry and academic environments are showing a lot of interest in the Software Engineering discipline. Therefore, it is a challenge for universities to provide students with appropriate training in this area, preparing them for their future professional practice. There are many difficulties to provide that training. The outstanding ones are: the Software Engineering area is too broad and class hours are scarce; the discipline requires a high level of abstraction; it is difficult to reproduce real world situations in the classroom to provide a practical learning environment; the number of students per professor is very high (at least in Spain); companies develop software with a maturity level rarely over level 2 of the CMM for Software (again, at least in Spain) as opposed to what is taught at the University. Besides, there are different levels and study plans, making more difficult to structure the contents to teach in each term and degree. In this paper we present a plan for teaching Software Engineering trying to overcome some of the difficulties above.

Fiabilidad de minimodulos de silicio

El objetivo de este Proyecto Final de Carrera es la realización de un ensayo de fiabilidad de componentes electrónicos, más concretamente de Minimódulos de Silicio, con el fin de estudiar su comportamiento a lo largo del tiempo de vida. Debido a la larga duración de los Minimódulos de Silicio , un ensayo de este tipo podría durar años, por lo que es necesario realizar un ensayo acelerado que acorte significativamente el tiempo del experimento, para ello, han de someterse a esfuerzos mayores que en condiciones normales de funcionamiento. A día de hoy, los Minimódulos de silicio, que conocemos como placas solares fotovoltaicas, se usan en infinidad de dispositivos debido a las múltiples ventajas que conllevan. La principal ventaja es poder llevar electricidad a cualquier parte del planeta sin necesidad de tener que hacer unas elevadas inversiones. Esta electricidad proviene de una fuente de energía inagotable y nada contaminante, con lo que ayudamos a mantener el equilibrio del planeta. La mayoría de las veces estas placas solares fotovoltaicas se usan en el exterior, soportando cambios de temperatura y de humedad elevados, de ahí, la importancia de realizar ensayos de fiabilidad, que muestren sus posibles causas de fallo, los efectos que producen estos fallos y los aspectos de diseño, fabricación y mantenimiento que puedan afectarles. Los Minimódulos de silicio utilizados en este proyecto son el modelo MC-SP0.8-NF-GCS de la empresa fabricante Multicomp. Para realizar el Proyecto hubiéramos necesitado una cámara climática que simulara unas condiciones ambientales determinadas, pero debido a la dificultad de iluminar el módulo dentro de la cámara climática hemos desarrollado un nuevo sistema de ensayos acelerados en temperatura. El nuevo sistema de ensayos acelerados consiste en: •Colocar los módulos fotovoltaicos en el laboratorio con un foco de 500W que irradia lo equivalente al sol. •Los tres módulos trabajarán a tres temperaturas diferentes para simular condiciones ambientales distintas, concretamente a 60°C, 72°C y 84°C. •Mediante un sistema automático de medida diseñado en LabVIEW, de manera simultánea tomará medidas de tensión en las tres placas y estudiaremos el grado degradación en cada placa. Se analizaran los resultados obtenido de cada una de las medidas y se realizará un estudio de fiabilidad y del proceso de degradación sufrido por los Minimódulos de silicio. Este PFC se puede dividir en las siguientes fases de trabajo siendo el ensayo la parte más larga en el tiempo: •Búsqueda de bibliografía documentación y normas aplicables. •Familiarización con los equipos y software, estudiando el manejo del software que viene con el Multímetro Keithley 2601 y el programa LabVIEW. •Desarrollo del hardware y sistemas necesarios para la realización del ensayo. •Montaje del ensayo •Realización del ensayo. •Análisis de resultados. ABSTRACT. The objective of this Final Project is conducting a test reliability of electronic components, more specifically Silicon minimodules, in order to study their behavior throughout the life span. Due to the long duration of Silicon minimodules a test like this could take years, so it is necessary to perform an accelerated significantly shorten the time of the experiment, testing for it, should be subjected to greater efforts than in normal operating. Today, the mini-modules, silicon is known as photovoltaic solar panels are used in a multitude of devices due to the many advantages they bring. The main advantage is to bring electricity to anywhere in the world without having to make high investments. This electricity comes from an inexhaustible source of energy and no pollution, thus helping to maintain the balance of the planet. Most of the time these solar photovoltaic panels are used on the outside, enduring changes in temperature and high humidity, hence, the importance of reliability testing, showing the possible causes of failure, the effects produced by these faults and aspects of design, manufacturing and maintenance that may affect them. The silicon mini-modules used in this project are the MC-SP0.8-NF-GCS model Multicomp manufacturing company. To realize the project we would have needed a climatic chamber to simulate specific environmental conditions, but due to the difficulty of illuminating the module in the climate chamber we have developed a new system of accelerated tests in temperature. The new system is accelerated tests: •Place the PV modules in the laboratory with a focus on the equivalent 500W radiating sun. •The three modules work at three different temperatures to simulate different environmental conditions, namely at 60 °C, 72 °C and 84 °C. •Automatic measurement system designed in LabVIEW, simultaneous voltage measurements taken at the three plates and study the degradation degree in each plate. The results obtained from each of the measurements and a feasibility study and degradation suffered by the silicon is performed minimodules were analyzed. This PFC can be divided into the following phases of the test work the longest part being overtime: •Literature search and documentation standards. •Familiarization with equipment and software, studying management software that comes with the Keithley 2601 multimeter and the LabVIEW program. •Development of hardware and systems necessary for the conduct of the trial. •Experiment setup •Carrying out the experiment. •Analysis of results.

Expression of B-nerve growth factor in rabbit male tract and seminal plasma

Nerve growth factor (NGF) has been recently identified as an ovulation inductor factor (OIF) in the seminal plasma (SP) (Ratto et al. PNAS 2012; 109:15042-7). The presence of OIF in rabbit has been suggested but this protein has not yet been identified. Our aim was to study the mRNA expression in the rabbit male reproductive tract and to identify the protein β-NGF in the SP.

Induction of ovulation in rabbit does using purified nerve growth factor and camel seminal plasma

The presence of an ovulation-inducing factor (OIF) in the seminal plasma (SP) of several species with spontaneous and induced ovulation, including the rabbit, has been documented. Recent studies have demonstrated that the OIF in the SP of camels (SPCAM) is a nerve growth factor (β-NGF). The aim of this study was to determine if purified β-NGF from mouse submandibular glands or SPCAM could provoke ovulation induction in the rabbit doe. A total of 35 females were synchronized with 25 IU of equine chorionic gonadotropin (Serigan, Laboratorios Ovejero, Spain) and allocated into 4 groups. Forty-eight hours later (Day 0), does were given a single dose (IM) of 1 mL of saline solution (SS; n = 8); 1 mL of gonadorelin (GnRH; Inducel, Laboratorios Ovejero, Spain; n = 9); 24 µg of β-NGF (2.5S-NGF; Promega, USA; n = 10); or 1 mL of centrifuged raw camel SP (SPCAM; 127 pg mL–1 NGF; n = 8). After treatment, an empty catheter was introduced through the vagina to simulate the nervous/mechanical stimulus of coitus (4 animals per group). Plasma LH concentrations were determined in blood samples taken 30 min before treatment and at 0, 30, 60, 90, and 120 min after injection. Progesterone concentrations were assessed at 0 and 120 min and every 2 days until Day 6 after treatment. Concentrations of β-NGF in camel SP and hormone determinations were made by enzyme immunoassay. Ovulation rate (OR) was determined after euthanasia on Day 7.