Influence of an upstream building on the wind-induced mean suction on the flat roof of a low-rise building

The effect of an upstream building on the suction forces on the flat roof of a low-rise building placed in the wake of the former is analyzed. The analysis has been performed by wind tunnel testing of a flat roof, low-rise building model equipped with pressure taps on the roof and different block-type buildings (only configurations where the upstream building is as high or higher than the downstream one are considered in this paper). The influence of the distance between both buildings on the wind loads on the downstream building roof is analyzed, as well as the height of the upstream one and the wind angle of incidence. Experimental results reveal that the wind load increases as the relative height of the upstream building increases, the wind load being highest for intermediate distances between buildings, when a passage between them is formed.

Urban wind energy: empirical optimization of high-rise building roof shape for the wind energy exploitation

El programa Europeo HORIZON2020 en Futuras Ciudades Inteligentes establece como objetivo que el 20% de la energía eléctrica sea generada a partir de fuentes renovables. Este objetivo implica la necesidad de potenciar la generación de energía eólica en todos los ámbitos. La energía eólica reduce drásticamente las emisiones de gases de efecto invernadero y evita los riesgos geo-políticos asociados al suministro e infraestructuras energéticas, así como la dependencia energética de otras regiones. Además, la generación de energía distribuida (generación en el punto de consumo) presenta significativas ventajas en términos de elevada eficiencia energética y estimulación de la economía. El sector de la edificación representa el 40% del consumo energético total de la Unión Europea. La reducción del consumo energético en este área es, por tanto, una prioridad de acuerdo con los objetivos "20-20-20" en eficiencia energética. La Directiva 2010/31/EU del Parlamento Europeo y del Consejo de 19 de mayo de 2010 sobre el comportamiento energético de edificaciones contempla la instalación de sistemas de suministro energético a partir de fuentes renovables en las edificaciones de nuevo diseño. Actualmente existe una escasez de conocimiento científico y tecnológico acerca de la geometría óptima de las edificaciones para la explotación de la energía eólica en entornos urbanos. El campo tecnológico de estudio de la presente Tesis Doctoral es la generación de energía eólica en entornos urbanos. Específicamente, la optimization de la geometría de las cubiertas de edificaciones desde el punto de vista de la explotación del recurso energético eólico. Debido a que el flujo del viento alrededor de las edificaciones es exhaustivamente investigado en esta Tesis empleando herramientas de simulación numérica, la mecánica de fluidos computacional (CFD en inglés) y la aerodinámica de edificaciones son los campos científicos de estudio. El objetivo central de esta Tesis Doctoral es obtener una geometría de altas prestaciones (u óptima) para la explotación de la energía eólica en cubiertas de edificaciones de gran altura. Este objetivo es alcanzado mediante un análisis exhaustivo de la influencia de la forma de la cubierta del edificio en el flujo del viento desde el punto de vista de la explotación energética del recurso eólico empleando herramientas de simulación numérica (CFD). Adicionalmente, la geometría de la edificación convencional (edificio prismático) es estudiada, y el posicionamiento adecuado para los diferentes tipos de aerogeneradores es propuesto. La compatibilidad entre el aprovechamiento de las energías solar fotovoltaica y eólica también es analizado en este tipo de edificaciones. La investigación prosigue con la optimización de la geometría de la cubierta. La metodología con la que se obtiene la geometría óptima consta de las siguientes etapas: - Verificación de los resultados de las geometrías previamente estudiadas en la literatura. Las geometrías básicas que se someten a examen son: cubierta plana, a dos aguas, inclinada, abovedada y esférica. - Análisis de la influencia de la forma de las aristas de la cubierta sobre el flujo del viento. Esta tarea se lleva a cabo mediante la comparación de los resultados obtenidos para la arista convencional (esquina sencilla) con un parapeto, un voladizo y una esquina curva. - Análisis del acoplamiento entre la cubierta y los cerramientos verticales (paredes) mediante la comparación entre diferentes variaciones de una cubierta esférica en una edificación de gran altura: cubierta esférica estudiada en la literatura, cubierta esférica integrada geométricamente con las paredes (planta cuadrada en el suelo) y una cubierta esférica acoplada a una pared cilindrica. El comportamiento del flujo sobre la cubierta es estudiado también considerando la posibilidad de la variación en la dirección del viento incidente. - Análisis del efecto de las proporciones geométricas del edificio sobre el flujo en la cubierta. - Análisis del efecto de la presencia de edificaciones circundantes sobre el flujo del viento en la cubierta del edificio objetivo. Las contribuciones de la presente Tesis Doctoral pueden resumirse en: - Se demuestra que los modelos de turbulencia RANS obtienen mejores resultados para la simulación del viento alrededor de edificaciones empleando los coeficientes propuestos por Crespo y los propuestos por Bechmann y Sórensen que empleando los coeficientes estándar. - Se demuestra que la estimación de la energía cinética turbulenta del flujo empleando modelos de turbulencia RANS puede ser validada manteniendo el enfoque en la cubierta de la edificación. - Se presenta una nueva modificación del modelo de turbulencia Durbin k — e que reproduce mejor la distancia de recirculación del flujo de acuerdo con los resultados experimentales. - Se demuestra una relación lineal entre la distancia de recirculación en una cubierta plana y el factor constante involucrado en el cálculo de la escala de tiempo de la velocidad turbulenta. Este resultado puede ser empleado por la comunidad científica para la mejora del modelado de la turbulencia en diversas herramientas computacionales (OpenFOAM, Fluent, CFX, etc.). - La compatibilidad entre las energías solar fotovoltaica y eólica en cubiertas de edificaciones es analizada. Se demuestra que la presencia de los módulos solares provoca un descenso en la intensidad de turbulencia. - Se demuestran conflictos en el cambio de escala entre simulaciones de edificaciones a escala real y simulaciones de modelos a escala reducida (túnel de viento). Se demuestra que para respetar las limitaciones de similitud (número de Reynolds) son necesarias mediciones en edificaciones a escala real o experimentos en túneles de viento empleando agua como fluido, especialmente cuando se trata con geometrías complejas, como es el caso de los módulos solares. - Se determina el posicionamiento más adecuado para los diferentes tipos de aerogeneradores tomando en consideración la velocidad e intensidad de turbulencia del flujo. El posicionamiento de aerogeneradores es investigado en las geometrías de cubierta más habituales (plana, a dos aguas, inclinada, abovedada y esférica). - Las formas de aristas más habituales (esquina, parapeto, voladizo y curva) son analizadas, así como su efecto sobre el flujo del viento en la cubierta de un edificio de gran altura desde el punto de vista del aprovechamiento eólico. - Se propone una geometría óptima (o de altas prestaciones) para el aprovechamiento de la energía eólica urbana. Esta optimización incluye: verificación de las geometrías estudiadas en el estado del arte, análisis de la influencia de las aristas de la cubierta en el flujo del viento, estudio del acoplamiento entre la cubierta y las paredes, análisis de sensibilidad del grosor de la cubierta, exploración de la influencia de las proporciones geométricas de la cubierta y el edificio, e investigación del efecto de las edificaciones circundantes (considerando diferentes alturas de los alrededores) sobre el flujo del viento en la cubierta del edificio objetivo. Las investigaciones comprenden el análisis de la velocidad, la energía cinética turbulenta y la intensidad de turbulencia en todos los casos. ABSTRACT The HORIZON2020 European program in Future Smart Cities aims to have 20% of electricity produced by renewable sources. This goal implies the necessity to enhance the wind energy generation, both with large and small wind turbines. Wind energy drastically reduces carbon emissions and avoids geo-political risks associated with supply and infrastructure constraints, as well as energy dependence from other regions. Additionally, distributed energy generation (generation at the consumption site) offers significant benefits in terms of high energy efficiency and stimulation of the economy. The buildings sector represents 40% of the European Union total energy consumption. Reducing energy consumption in this area is therefore a priority under the "20-20-20" objectives on energy efficiency. The Directive 2010/31/EU of the European Parliament and of the Council of 19 May 2010 on the energy performance of buildings aims to consider the installation of renewable energy supply systems in new designed buildings. Nowadays, there is a lack of knowledge about the optimum building shape for urban wind energy exploitation. The technological field of study of the present Thesis is the wind energy generation in urban environments. Specifically, the improvement of the building-roof shape with a focus on the wind energy resource exploitation. Since the wind flow around buildings is exhaustively investigated in this Thesis using numerical simulation tools, both computational fluid dynamics (CFD) and building aerodynamics are the scientific fields of study. The main objective of this Thesis is to obtain an improved (or optimum) shape of a high-rise building for the wind energy exploitation on the roof. To achieve this objective, an analysis of the influence of the building shape on the behaviour of the wind flow on the roof from the point of view of the wind energy exploitation is carried out using numerical simulation tools (CFD). Additionally, the conventional building shape (prismatic) is analysed, and the adequate positions for different kinds of wind turbines are proposed. The compatibility of both photovoltaic-solar and wind energies is also analysed for this kind of buildings. The investigation continues with the buildingroof optimization. The methodology for obtaining the optimum high-rise building roof shape involves the following stages: - Verification of the results of previous building-roof shapes studied in the literature. The basic shapes that are compared are: flat, pitched, shed, vaulted and spheric. - Analysis of the influence of the roof-edge shape on the wind flow. This task is carried out by comparing the results obtained for the conventional edge shape (simple corner) with a railing, a cantilever and a curved edge. - Analysis of the roof-wall coupling by testing different variations of a spherical roof on a high-rise building: spherical roof studied in the litera ture, spherical roof geometrically integrated with the walls (squared-plant) and spherical roof with a cylindrical wall. The flow behaviour on the roof according to the variation of the incident wind direction is commented. - Analysis of the effect of the building aspect ratio on the flow. - Analysis of the surrounding buildings effect on the wind flow on the target building roof. The contributions of the present Thesis can be summarized as follows: - It is demonstrated that RANS turbulence models obtain better results for the wind flow around buildings using the coefficients proposed by Crespo and those proposed by Bechmann and S0rensen than by using the standard ones. - It is demonstrated that RANS turbulence models can be validated for turbulent kinetic energy focusing on building roofs. - A new modification of the Durbin k — e turbulence model is proposed in order to obtain a better agreement of the recirculation distance between CFD simulations and experimental results. - A linear relationship between the recirculation distance on a flat roof and the constant factor involved in the calculation of the turbulence velocity time scale is demonstrated. This discovery can be used by the research community in order to improve the turbulence modeling in different solvers (OpenFOAM, Fluent, CFX, etc.). - The compatibility of both photovoltaic-solar and wind energies on building roofs is demonstrated. A decrease of turbulence intensity due to the presence of the solar panels is demonstrated. - Scaling issues are demonstrated between full-scale buildings and windtunnel reduced-scale models. The necessity of respecting the similitude constraints is demonstrated. Either full-scale measurements or wind-tunnel experiments using water as a medium are needed in order to accurately reproduce the wind flow around buildings, specially when dealing with complex shapes (as solar panels, etc.). - The most adequate position (most adequate roof region) for the different kinds of wind turbines is highlighted attending to both velocity and turbulence intensity. The wind turbine positioning was investigated for the most habitual kind of building-roof shapes (flat, pitched, shed, vaulted and spherical). - The most habitual roof-edge shapes (simple edge, railing, cantilever and curved) were investigated, and their effect on the wind flow on a highrise building roof were analysed from the point of view of the wind energy exploitation. - An optimum building-roof shape is proposed for the urban wind energy exploitation. Such optimization includes: state-of-the-art roof shapes test, analysis of the influence of the roof-edge shape on the wind flow, study of the roof-wall coupling, sensitivity analysis of the roof width, exploration of the aspect ratio of the building-roof shape and investigation of the effect of the neighbouring buildings (considering different surrounding heights) on the wind now on the target building roof. The investigations comprise analysis of velocity, turbulent kinetic energy and turbulence intensity for all the cases.

A parametric, experimental analysis of conical vortices on curved roofs of low-rise buildings

Different methods to reduce the high suction caused by conical vortices have been reported in the literature: vertical parapets, either solid or porous, placed at the roof edges being the most analysed configuration. Another method for alleviating the high suction peaks due to conical vortices is the use of some non-standard parapet configuration like cantilever parapets. In this paper the influence of roof curvature on the conical vortex pattern appearing on a curved roof (Fig. 1) when subject to oblique winds is experimentally analysed by testing the mean pressure distribution on the curved roofs of low-rise building models in a wind tunnel. Also, the efficiency of cantilever parapets to reduce mean suction loads on curved roofs is experimentally checked. Very high suction loads have been measured on curved roofs, the magnitude of these high suction loads being significantly decreased when cantilever parapets are used. Thus, the suitability of these parapets to reduce wind pressure loads on curved roofs is demonstrated.

Wind tunnel analysis on the influence of cantilever parapets on the wind loads on curved roofs

Different methods to reduce the high suction caused by conical vortices have been reported in the literature: vertical parapets, either solids or porous, placed at the roof edges being the most analysed configuration. Another method for alleviating the high suction peaks due to conical vortices is to round the roof edges. Very recently, the use of some non-standard parapet configurations, like cantilever parapets, has been suggested. In this paper, its efficiency to reduce suction loads on curved roofs is experimentally checked by testing the pressure distribution on the curved roof of a low-rise building model in a wind tunnel. Very high suction loads have been measured on this model, the magnitude of these high suction loads being significantly decreased when cantilever...

Lo público en lo privado : la calle elevada como catalizador del encuentro colectivo

En la actualidad, el individualismo social originado por las nuevas sociedades de la información, la crisis económica, y, aún más acusado por aquella arquitectura que busca la máxima rentabilidad, ha provocado una creciente incomunicación entre las personas que comparten los mismos espacios residenciales. La presente tesis doctoral aborda el estudio del espacio común dentro del proyecto de vivienda colectiva, desde la noción de espacio intermedio, entendido como frontera espacial –entre el espacio público de la ciudad y la atmosfera íntima de la vivienda– donde tienen lugar los encuentros sociales entre residentes. El principal objetivo de la investigación es rescatar y poner en valor principios básicos del diseño arquitectónico –muchos de ellos en desuso– que mejoran la calidad del espacio colectivo y favorecen la aparición de una atmósfera agradable para el encuentro interpersonal, así como un intento de codificación de estos aspectos, atendiendo a criterios conceptuales que definen el espacio público contemporáneo. La hipótesis de partida se basa en la consideración del proyecto de viviendas como modelo análogo al proyecto urbano de la ciudad –con el que guarda sugerentes similitudes–, y los espacios intermedios como espacio de referencia que pone en valor aquello que liga – integrado en el propio proyecto–. Este supuesto básico ha permitido a diferentes autores poner en relación fecunda el diseño de la casa, el edificio y la ciudad, con el individuo, la comunidad y la sociedad; y ha posibilitado plantear la trasposición de conceptos arquitectónicos fructíferos, en relación con el espacio público –usando como representante la idea de calle elevada–, que ahora pueden enriquecer el entorno privado del edificio. Sirviéndose de instrumentos específicos de la disciplina arquitectónica, la tesis trata de explicar la devaluación a nivel social de los espacios colectivos, derivada de la construcción en altura y del uso excesivo de la estandarización en el proyecto de viviendas a partir del período de postguerra, e intensificada en el postmodernismo por la revolución de las comunicaciones. Se puede así reorientar el diseño de los proyectos de vivienda colectiva no como una simple agrupación de viviendas que favorecen la incomunicación, sino tratando de impulsar unas edificaciones que potencien la comunicación interpersonal. La reunión y reagrupación de un vocabulario arquitectónico específico, acorde con la complejidad social intrínseca en los espacios colectivos, amplia el alcance de los conceptos tratados. Dicha terminología se basa principalmente en mecanismos de cualificación espacial y permite evaluar la dimensión colectiva de la esfera semipública en el edificio de viviendas. ABSTRACT Currently, the social individualism caused by the new societies of information, the economic crisis and even more by architecture, which looks for maximum profitability, has led to a rising lack of communication between people that share the same living space. This doctoral thesis deals with the study of common space, which is based on the notion of in-between space, within the collective housing project. It is considered as a spatial frontier –between the public space of the city and the intimate atmosphere of the housing– where social contact between residents takes place. The main purpose of this research is to collect basic principles of architectural design –many of them no longer in use– that improve the quality of collective space. Following conceptual criteria that define the contemporary public space, they encourage the emergence of a pleasant atmosphere for interpersonal meeting as well as an attempt to codify these aspects. The initial hypothesis is based on the consideration of the housing project as a model analogous to the urban project of the city, with which it bears some similarities. Furthermore, it is based on the in-between spaces as space of reference that valuates what binds – integrated in the project-. That basic supposition has served various authors to connect the design of the house, the building and the city with the individual, the community and the society. In addition –regarding public space and using the idea of the street in the sky as representative–, it has enabled to bring up the transposition of productive architectural concepts, which can now enrich the private environment of the building. Using specific architectural instruments, this thesis deals with explaining the social devaluation of collective spaces. It has resulted from the high rise building construction as well as from the excessive standardization in the housing project since the postwar period and is intensified by the communications revolution in postmodernism. Thus, it is possible to change the design of collective housing projects not as a mere cluster of dwellings that enhance isolation, but by trying to promote buildings that improve interpersonal communication. The collection and regrouping of a specific architectural vocabulary, in accordance with the social complexity inherent in collective spaces, expands the scope of the discussed concepts. Such terminology is mainly based on qualifying spatial strategies and allows to assess the collective dimension of the semi-public sphere in dwelling.

A new way of teaching different subjects in a foreign language in the Building Engineering Degree at the Universidad Politécnica.

The European Union has been promoting linguistic diversity for many years as one of its main educational goals. This is an element that facilitates student mobility and student exchanges between different universities and countries and enriches the education of young undergraduates. In particular, a higher degree of competence in the English language is becoming essential for engineers, architects and researchers in general, as English has become the lingua franca that opens up horizons to internationalisation and the transfer of knowledge in today’s world. Many experts point to the Integrated Approach to Contents and Foreign Languages System as being an option that has certain benefits over the traditional method of teaching a second language that is exclusively based on specific subjects. This system advocates teaching the different subjects in the syllabus in a language other than one’s mother tongue, without prioritising knowledge of the language over the subject. This was the idea that in the 2009/10 academic year gave rise to the Second Language Integration Programme (SLI Programme) at the Escuela Arquitectura Técnica in the Universidad Politécnica Madrid (EUATM-UPM), just at the beginning of the tuition of the new Building Engineering Degree, which had been adapted to the European Higher Education Area (EHEA) model. This programme is an interdisciplinary initiative for the set of subjects taught during the semester and is coordinated through the Assistant Director Office for Educational Innovation. The SLI Programme has a dual goal; to familiarise students with the specific English terminology of the subject being taught, and at the same time improve their communication skills in English. A total of thirty lecturers are taking part in the teaching of eleven first year subjects and twelve in the second year, with around 120 students who have voluntarily enrolled in a special group in each semester. During the 2010/2011 academic year the degree of acceptance and the results of the SLI Programme have been monitored. Tools have been designed to aid interdisciplinary coordination and to analyse satisfaction, such as coordination records and surveys. The results currently available refer to the first and second year and are divided into specific aspects of the different subjects involved and into general aspects of the ongoing experience.

Los agentes de la edificación desde el punto de vista de la Gestión Integral de Proyectos: diferencias y semejanzas entre la Legislación Española y los Estándares Internacionales = Expert agents in the Global Development of a building project: differences and similarities between Spanish and International contexts.

Desde los años 60, crece en Europa y Estados Unidos la preocupación y la necesidad de mejorar los procesos de gerencia de los proyectos de construcción al volverse estos más complejos. Esto ha llevado a la continua aparición de nuevos profesionales desde la fecha citada hasta nuestros días. De ahí la complejidad de conocer las cualidades de cada uno de ellos, así como las funciones a realizar o la formación que deben tener para poder desarrollar el puesto de trabajo según el papel que desempeñan para cada actividad. Muchos agentes son los que pueden intervenir en la edificación, muchas son las funciones que llevan a cabo estos agentes, muchas son las habilidades que se necesitan para realizar estas misiones, y una buena gestión de la edificación es la que hay que desarrollar para lograr el gran éxito. El presente trabajo fin de máster, dirigido a arquitectos, arquitectos técnicos, ingenieros, abogados, economistas y todos los profesionales del sector inmobiliario y de la construcción, trata de resolver todas aquellas dudas sobre los diferentes sujetos que estarán presentes desde la definición del proyecto en la fase inicial hasta el final de la obra, pasando por las fases de pre-construcción, construcción y post-construcción. (ENGLISH VERSION) Since the 1960s, most construction projects have become more and more complex, and new concerns and necessities related to the management of a project have been on the rise in Europe and in the United States. Thence, the need for more specialized professionals in the field has become a common fact, as well as the inclusion of new curricular subjects in most building engineering studies. There are different agents that play a relevant role in a building project; some of them are expected to perform a highly specialized set of functions that require specific management skills for the work to be successful. This research work—aimed mainly at engineers, quantity surveyors, lawyers, economists, real estate and construction professionals—shows the major implications of the building construction process including both pre-tender/construction and post-tender/construction stages as far as the main expert agents are involved.

La arquitectura residencial en El Real Sitio de El Pardo (1885 - 1965): Orígenes, tipos y configuración del trazado urbano

Tras la denominación de Real Sitio a mediados del siglo XVIII, bajo el reinado de Fernando VI, su sucesor Carlos III procedió a la incorporación a su Patrimonio de todos los Montes y Bosques de El Pardo. Comenzó entonces el proceso de planeamiento urbano y de construcción arquitectónica que finalizó en torno al año 1800. En lo sucesivo, no sólo se mantiene el curso de la conservación y consolidación de los edificios principales, sino que se realiza obra nueva de índole civil. Algunos edificios cambiaron de propiedad y de uso hasta que tras la Guerra Civil se procedió a la mayor transformación vivida por el Real Sitio. El intervalo que aquí se trata (1885 a 1965), no ha suscitado, en los estudios sobre El Pardo, atención suficiente al no acontecer obra nueva de carácter patrimonial ni ha sido objeto de análisis el trazado y la fisonomía del centro urbano residencial del pueblo que Carlos III configuró. Sin embargo se estima relevante analizar los cambios en la actividad residencial; en primer lugar porque coexiste con la arquitectura oficial y, por tanto, se entiende necesario un análisis global del conjunto y en segundo lugar porque facilita la comprensión sobre la imagen original de carácter histórico del conjunto de finales del siglo XVIII. Este marco temporal determina tres partes principales de estudio que estructuran la presente tesis, cuyas fechas establecen los intervalos históricos clave: Actuaciones sobre el núcleo urbano consolidado (1885-1931). Cese de la actividad constructiva (1931-1939). Propuestas regeneradoras y crecimiento acelerado (1939-1965). Dentro de ellos se establecen, a su vez, dos subcapítulos diferenciados con la finalidad de explicar los sucesos que pautaron los cambios trascendentales en la historia de El Pardo. En el estudio del estado de la cuestión se observa que en El Pardo, al igual que sucede en otros Reales Sitios, se investigan los edificios destacados como el Palacio, la Casita del Príncipe, la Casa de Oficios y la Casa de Infantes desde el punto de vista de su historia pero no desde la arquitectura ni de cómo esta afecta al desarrollo del trazado y por tanto al contexto urbano. Se manifiestan determinadas carencias de tratamiento gráfico que facilitarían la comprensión histórica mediante el análisis de la forma y cómo esta ha ido variando sustancialmente. El concepto de escala y orientación reordena el estudio, no sólo de estos edificios protagonistas sino de los que se entretejen a su alrededor y componen el conjunto histórico, lo cual aporta nuevas conclusiones al estado de la cuestión que aquí compete. El principal objetivo de la tesis es, por tanto, contribuir a la dimensión patrimonial mediante el estudio de la arquitectura residencial del pueblo de El Pardo y en cómo esta ha ido conformando y consolidando el entramado urbano original en torno a edificios de la realeza y corte. Analizar aquellos edificios que perduran, los que fueron reconstruidos, rehabilitados, y apuntar acontecimientos históricos que formularon la actual fisonomía. Sistematizar y reordenar sobre la traza actual los edificios que desaparecieron, nos da las pistas sobre las modificaciones en concepto de escala arquitectónica y urbana. El estudio de las fuentes y establecer una metodología de conexión de estas, ayuda a detectar dónde no se han dirigido aún los focos de interés así como las lagunas que han quedado por explorar con el fin de responder a nuevas hipótesis, conceder conclusiones y abrir otras líneas de investigación. Como conclusiones generales, la tesis aporta documentación nueva sobre el objeto de estudio, no solicitada, digitalizada o publicada con anterioridad. En ella se analizan los procesos de configuración, consolidación y transformación en el Real Sitio mediante la sistematización de estados comparativos. Con respecto al estudio de los diferentes contextos natural y urbano la tesis analiza cómo los accidentes naturales, el desarrollo de infraestructuras y el impulso de la agronomía afectaron a El Pardo a partir del siglo XIX, y estudia los procesos de configuración, consolidación y transformación en el Real Sitio mediante la sistematización de la documentación encontrada de manera gráfica y escrita. En relación al marco patrimonial arquitectónico, la tesis analiza los procesos edificatorios históricos. Se estudian, a su vez, cambios de ocupación o uso que derivaron en reformas, ampliaciones, obras de nueva planta e incluso en derribos, así como los proyectos no materializados o que se llevaron a cabo de manera parcial. Con respecto al análisis del momento histórico, la tesis analiza las posibles afectaciones, políticas, sociales y económicas en las etapas de Monarquía, Segunda República, Guerra Civil y Posguerra. Por último, la tesis abre cuatro vías de investigación (que ya se han tratado y avanzado en parte pero que escapan a los límites de este trabajo) que pueden plantear nuevas hipótesis, reportando así respuestas sobre objetos de estudio complementarios y paralelos al presente. Estas refieren a análisis más concretos sobre El Palacio Real de El Pardo y la Casa de Oficios, el Camino Real de Madrid a El Pardo desde la Puerta de Hierro, los cuarteles, puertas y portilleras del Monte de El Pardo y los proyectos desarrollados por el arquitecto Diego Méndez en los Reales Sitios para el Patrimonio Nacional. ABSTRACT Following the Royal Site denomination being granted in the mid-18th Century, during the reign of Ferdinand VI, his successor Charles III proceeded to include all the Forests and Woodlands of El Pardo in his heritage. That then gave rise to the process of town planning and architectural construction that was completed around 1800. Thereafter, not only the process of conservation and consolidation of the main buildings has been maintained, but new civil engineering works have also been carried out. Some buildings changed ownership and use until, after the Civil War, the greatest transformation experienced by the Royal Site was undertaken. The time frame this paper concerns (1885 to 1965), has not attracted sufficient attention in studies of El Pardo due to there having been no new works with heritage status, nor has there been an analysis of the layout and external appearance of the residential centre in the town once conceived by Charles III. However, it is considered relevant to analyse the changes in residential activity, firstly, because it coexists with the official architecture and, thus, it is considered necessary to perform a global analysis of the complex and, secondly, because it facilitates a historical understanding of the original appearance of the complex at the end of the 18th Century. This time framework defines three main parts of the study that provide the structure of this thesis, the dates of which establish the key historical time frames: Actions in the consolidated town centre (1885-1931). Cessation of construction works (1931-1939). Proposals of regeneration and accelerated growth (1939-1965). Two distinct sub-chapters are also established within these, in order to explain the events that marked the transcendental changes in the history of El Pardo. When studying the subject matter, it is noted that in El Pardo, as is the case in other Royal Sites, outstanding buildings such as the Palace, the Prince's Cottage, the Trades House and the Infantes House are usually researched strictly from the point of view of their history, but not from an architectural perspective, nor analysing how that affects the development of the site layout and thus the urban area. Specific shortcomings are evident in the graphic treatment that would have otherwise facilitated a historical understanding through the analysis of the shape and the way it has gradually undergone substantial variation. The concept of scale and orientation reorganises the study, not only of these key buildings, but also of those that are woven around them and make up the historic complex, allowing entirely new conclusions concerning the subject matter analysed herein. Therefore, the main purpose of this thesis is to outline our heritage through the study of the residential architecture of the town of El Pardo and the analysis of the way the original town has been built up and consolidated around the buildings erected by royalty and the court; to analyse the buildings that still remain, those that were rebuilt, refurbished, and to note historic events that shaped its current appearance. To this end, a systematic classification and reorganisation on the current urban layout of the buildings that have disappeared will give us the key to understand changes in the concept of architectural and urban scale. Studying the sources and establishing a methodology to connect them will help us detect those areas where the focus of interest has not concentrated yet, and will also reveal the gaps that remain unexplored, in order to respond to new hypotheses, reach new conclusions and open up new lines of research. As general conclusions, this thesis provides new documentation on the subject matter that had not been requested, digitized or published before. There we find an analysis of the processes of configuration, consolidation and transformation of the Royal Site through a systematic classification of comparative states. With regard to the study of the multiple natural and urban environments, this thesis analyses the way natural features, development of infrastructures and agricultural driving forces affected El Pardo as of the 19th Century, and it studies the processes of configuration, consolidation and transformation of the Royal Site by systematically classifying the documentation found in graphic and written documents. In relation to the architectural heritage framework, this thesis analyses historical building processes. Likewise, a study is also performed on the changes in land occupation or use that led to reforms, extensions, new buildings and even to demolitions, as well as on unrealized projects, or even on those that were partially implemented. As for the analysis of the historical time period, this thesis assesses the potential political, social and economic effects of the Monarchy, Second Republic, Civil War and Post-War Periods. Finally, this thesis opens up four lines of investigation (that have already been discussed and partially advanced, but which fall beyond the scope of this work) that could pose new hypotheses, thus giving answer to other subject matters parallel and complementary to the one assessed herein. These refer to more specific analyses of El Palacio Real de El Pardo (Royal Palace of El Pardo) and the Casa de Oficios (Trades House), the Royal Highway from Madrid to El Pardo from Puerta de Hierro, the barracks, gates and entrances to estates in the Woodlands of El Pardo and the projects developed on the Royal Sites by the architect Diego Méndez for the National Heritage.

Wind tunnel study on the influence of different parapets on the roof pressure distribution of low-rise buildings

High suction loads appear on roofs of low-height buildings. The use of parapets with appropriate height at the roof edges alleviates these loads. The performance of six parapet configurations to decrease the suction loads induced on roofs by oblique winds has been studied in a low speed wind tunnel. The studied parapet configurations include vertical wall parapets, either solid or porous, and cantilevered parapets formed by a small horizontal roof close to the building roof. Low-height parapets with a medium porosity and cantilevered parapets are more efficient than solid parapets to reduce the wind suctions generated on the roofs by conical vortices.

Integrated approach to foreign language in the building engineering degree at the Universidad Politécnica Madrid

The European Union has been promoting linguistic diversity for many years as one of its main educational goals. This is an element that facilitates student mobility and student exchanges between different universities and countries and enriches the education of young undergraduates. In particular,a higher degree of competence in the English language is becoming essential for engineers, architects and researchers in general, as English has become the lingua franca that opens up horizons to internationalisation and the transfer of knowledge in today’s world. Many experts point to the Integrated Approach to Contents and Foreign Languages System as being an option that has certain benefits over the traditional method of teaching a second language that is exclusively based on specific subjects. This system advocates teaching the different subjects in the syllabus in a language other than one’s mother tongue, without prioritising knowledge of the language over the subject. This was the idea that in the 2009/10 academic year gave rise to the Second Language Integration Programme (SLI Programme) at the Escuela Arquitectura Tecnica in the Universidad Politecnica Madrid (EUATM-UPM), just at the beginning of the tuition of the new Building Engineering Degree, which had been adapted to the European Higher Education Area (EHEA) model. This programme is an interdisciplinary initiative for the set of subjects taught during the semester and is coordinated through the Assistant Director Office for Educational Innovation. The SLI Programme has a dual goal; to familiarise students with the specific English terminology of the subject being taught, and at the same time improve their communication skills in English. A total of thirty lecturers are taking part in the teaching of eleven first year subjects and twelve in the second year, with around 120 students who have voluntarily enrolled in a special group in each semester. During the 2010/2011 academic year the degree of acceptance and the results of the SLI Programme are being monitored. Tools have been designed to aid interdisciplinary coordination and to analyse satisfaction, such as coordination records and surveys. The results currently available refer to the first semester of the year and are divided into specific aspects of the different subjects involved and into general aspects of the ongoing experience.

El vidrio y sus máscaras : el sueño de la arquitectura de cristal

Según Heidegger, la esencia de la arquitectura, de la construcción, descansa en un no espacio: en la materia con que se construyen las fronteras que otorgan espacios, irradiando sobre ellos aquello que los caracteriza. Si hay alguna materia, de las utilizadas por la arquitectura a lo largo de su historia para construir fronteras, que haya mantenido una especial relación con la luz y la visión, dando un carácter inconfundible a los espacios aviados por ellas, esta es el vidrio; algunas de las etimologías de su nombre: zakû (ser claro), hyalos (diáfano) o vitrum (ver), así lo evidencian. Posiblemente, sea la pregnancia de este modo fascinante de relacionarse con la luz, la que ha hecho del vidrio, a lo largo del tiempo que lleva siendo usado en arquitectura, y aún antes, el material que ha provocado en el imaginario humano la ilusión de ser aquel en que, en último término, podrían llegar a sublimarse todos los demás, dando lugar con ello a lo que en la tesis hemos denominado el sueño de la arquitectura de cristal. Siendo la luz, siempre, energía, consideraremos en la tesis luz-energía, a aquella que ilumina y calienta; es una luz científica y mesurable. Cuando la luz se “hace visible”, desvelando un mensaje “contenido” en el vidrio, hablaremos de luz-información. Esta luz, no puede medirse científicamente. La luz-energía y la luz-información, se manifiestan al conjuro de la arquitectura de vidrio. Es la segunda la que ha conformado las fronteras de vidrio enmascarado, y la que se estudia con más detenimiento en la tesis. Los distintos modos de usar en arquitectura la infinita combinatoria de las propiedades de absortancia, reflectancia, transmitancia y translucencia del vidrio, ha condicionado al hombre en su manera de “ver” el mundo. Unas veces, “inmerso” en él, puesto que solo lo separa del mismo, una frontera transparente, y “deseadamente” invisible: ese modo de usar el vidrio, ha sido el sueño imposible de una parte importante de la arquitectura del siglo XX. Otras veces, para “aislarse” de él, el hombre ha manipulado la luz y el vidrio para construir mundos diferentes. Las fronteras de vidrio enmascarado de color, mosaicos, vidrieras, pantallas y lo que hemos llamado vidrios complejos (con un cometido similar al que Schiller atribuía al coro en la tragedia griega, aislar a esta del “mundo real”, para mantener su libertad poética), son las fronteras que han construido el sueño posible de la arquitectura de cristal. Ambas actitudes, en distintos momentos de la historia de la arquitectura, han sido dos formas de querer materializar un mismo sueño. La capacidad del vidrio para adaptarse a tantos modos de presentarse ante nosotros, y a poder ser interpretado de tantas formas diferentes, es la que ha servido para dar título a la tesis, pues hasta en su faceta más transparente, el vidrio, de una forma o de otra, se ha mostrado siempre como un material enmascarado en el más amplio sentido de la palabra: se enmascara, incluso cuando apela a la transparencia o se convierte en espejo, para hacernos caer en la ilusión de que no está presente. Cuando el hombre construyó fronteras de vidrio e incluso antes, cuando soñó que con él podría llegar a construirlas, condensó en ellas toda la mítica, la mística y la epistemología en torno a la luz y la visión, dando lugar a una serie de arquetipos arquitectónicos. En la iglesia bizantina, la luz sobre, o la luz desde, los mosaicos, construyó una frontera titilante; y en la catedral gótica, la luz a través de las vidrieras construyó una frontera radiante; en ambos casos con el fin de alcanzar anagógicamente lo Inteligible. En el siglo XIX, con el descubrimiento de la electricidad y su incorporación a la arquitectura, las fronteras se vuelven fulgurantes, aviando, en este caso, el espacio urbano. Poco antes, en este mismo siglo, el espíritu del gótico tiene un efímero resurgir del que se nutrirá, a comienzos del siglo XX, el expresionismo cristalino, en el que la luz anagógica se hace laica. El espacio urbano fulgurante prefigurado por este movimiento y presente en las ciudades desde principios del siglo XX, fue potenciado a mediados de ese siglo con la aparición de las pantallas, extendiéndose desde entonces, imparable, por todo el planeta. La reciente emergencia de los vidrios complejos, ha abierto la posibilidad de construir fronteras a la carta (de vidrios de propiedades múltiples, seleccionadas de forma voluntaria y variable en cada momento). En principio, se pensó que, el uso de estos vidrios como cerramiento, podría llegar a constituirse como la panacea de los problemas del material relacionados con la luz-energía, sin necesidad de recurrir a “prótesis”, y manteniendo por tanto la seductora tersura de la fachada; aunque parece que, por ahora, esa posibilidad es, cuando menos, lejana. Sin embargo, en el campo de las megapantallas urbanas (y ,en general, en el de las pantallas de información), ubicuas actualmente en nuestras vidas, los vidrios complejos ayudan a construir los espesos velos de ilusión, que según Lefebvre sirven para mantener el capitalismo, siendo el último estadio de un desarrollo tecnológico, impuesto por el principio de economía del hombre, que como un metrónomo inexorable, y a modo de contrapunto, ha acompañado siempre (de nuevo en palabras de Lefebvre), a la necesidad del gasto, del juego, de la lucha, del arte, de la fiesta. La tecnología y el arte forman parte de la cultura producida por la sociedad y como señala Lévi-Strauss, esa cultura imprime orden; por el contrario, la sociedad, entendida como el conjunto de relaciones que los hombres mantienen entre sí, produce desorden. Del equilibrio entre esos extremos, surge el progreso, incluido el de la arquitectura. Las fronteras de vidrio que analizamos en la tesis –que avían espacios para la espiritualidad, el fasto y el espectáculo o, desde otro punto de vista, para las distintas manifestaciones del poder: la iglesia, la monarquía, el estado o el mercado– también han surgido de esa concomitancia entre el desorden y el orden; y forma parte de ese desorden, la aventura que ha impulsado al genio individual de místicos, alquimistas, geómetras, abades, reyes, inventores, poetas y arquitectos, a explorar, como escribe Apollinaire, vastos y extraños territorios donde el misterio en flor, se ofrece a quien quiera cogerlo, hogueras nuevas de colores nunca vistos, mil fantasmas imponderables a los que dar cuerpo. ABSTRACT According to Heidegger, the essence of architecture, building, lies in a non-space: the material that creates the boundaries from which something begins its presencing, radiating onto them that which characterizes them. If there is any single material amongst all those used throughout the history of architecture to build boundaries which has maintained a special relationship with light and vision, which has bestowed a distinctive character on spaces avid for them, it is glass. This is evidenced in some of its etymologies: zakû (to be clear), hyalos (transparent), vitrum (see). The rich potential of this fascinating way of relating to light in the history of the architectural use of glass, and even before, is possibly what has triggered the illusion in human imagination of being something that can ultimately sublimate all others, giving rise to what in this thesis we call The Dream of Crystal Architecture. Given that light is always energy, in this thesis we consider energy-light to be that which illuminates and warms. This is scientific, measurable light. When light "becomes visible" and reveals a message “contained” in glass, we speak of information-light. This light cannot be measured scientifically. Energy-light and information-light are manifested under the spell of glass architecture. The latter is what has shaped the boundaries of coloured glass, which is studied in this thesis. Architecture's different ways of using the infinite combinations of the absorptance, reflectance, transmittance and translucency of glass has affected the way we humans "see" the world. Sometimes we are "immersed" in it, since only an invisible, transparent boundary separates us from it: this use of glass has characterized a considerable part of 20th century architecture. In other cases, in order to "isolate" us from it, we have manipulated light and glass to build different worlds: the boundaries of glass "masked" by colour, mosaics, stained glass, screens and what we have called complex glazing, which plays a similar role to what Schiller attributed to the chorus in Greek tragedy, isolating it from the "real world" in order to maintain its poetic license. These are the boundaries that have built the viable dream of crystal architecture. These two approaches have been different ways of making same dream come true at different times in the history of architecture. The ability of glass to adapt to so many forms of manifestation, and interpretation, is what has given rise to the title of the thesis. Even in its most transparent facet, glass has one way or another always been a masking material in the broadest sense of the word: it is masked even when it invites transparency or becomes a mirror, triggering the illusion that it is not present. When man began to build glass boundaries, and even before, when he dreamed that he could build them, he condensed in them all the mythology, mysticism and epistemology concerning light and vision, which gave rise to a series of architectural archetypes. In the Byzantine church, light on or from mosaics created tenuous boundaries. In Gothic cathedrals, the light through the stained glass windows constructed radiant boundaries. In both cases the aim was to achieve, in an anagogical way, the Intelligible. In the 19th, the discovery of electricity and its use in architecture led to the production of dazzling boundaries, in this case employed in urban spaces. Earlier in the same century, the Gothic spirit had a short-lived revival, which in the early 20th century drew from crystalline expressionism in which anagogic light became secular. The dazzling urban space prefigured by this movement, present in cities since the early 20th century, was intensified in the mid-century with the emergence of screens, and since then it has spread unstoppably across the world. The recent emergence of complex glasses has made it possible to build boundaries on demand in glass with multiple properties, chosen at will and at whim at any time. Initially it was thought that the use of this glass as a wall could eventually become the panacea for the material problems related to energy-light, without needing to resort to "prosthesis" and thereby maintain the seductive smoothness of the facade. For now, that possibility seems remote, to say the least. In the realm of urban megascreens and information screens in general, now ubiquitous in our lives, complex glasses help to build the thick veils of illusion which, according to Lefebvre, serve to maintain capitalism. Like an inexorable metronome, in counterpoint, this ultimate state of technological development imposed by man's principle of economy has in fact always accompanied (again in the words of Lefebvre), the need to spend, play, fight, art, and party. Technology and art are part of the culture produced by society. As Levi-Strauss says, this culture imposes order. On the contrary, society, understood as a set of relationships amongst people, produces disorder. Progress, including that of architecture, arises from the balance between these two extremes. The glass boundaries analyzed in this thesis, which propitiate spaces for spirituality, pomp and spectacle or, from a different perspective, for the various manifestations of power: the church, the monarchy, the state and the market, have also emerged from the concomitance of order and disorder. One aspect of this disorder is the adventure that has inspired the individual genius of mystics, alchemists, surveyors, abbots, kings, inventors, poets and architects to explore, as Apollinaire says, vast, strange domains where flowering mystery offers itself to whoever wishes to pluck it, new fires, colours you have never seen before, a thousand intangible phantasms still awaiting reality.

Estimate of the total volume of Svalbard glaciers, and their potential contribution to sea-level rise, using new regionally based scaling relationships

We present a set of new volume scaling relationships specific to Svalbard glaciers, derived from a sample of 60 volume–area pairs. Glacier volumes are computed from ground-penetrating radar (GPR)-retrieved ice thickness measurements, which have been compiled from different sources for this study. The most precise scaling models, in terms of lowest cross-validation errors, are obtained using a multivariate approach where, in addition to glacier area, glacier length and elevation range are also used as predictors. Using this multivariate scaling approach, together with the Randolph Glacier Inventory V3.2 for Svalbard and Jan Mayen, we obtain a regional volume estimate of 6700 ± 835 km3, or 17 ± 2 mm of sea-level equivalent (SLE). This result lies in the mid- to low range of recently published estimates, which show values as varied as 13 and 24 mm SLE. We assess the sensitivity of the scaling exponents to glacier characteristics such as size, aspect ratio and average slope, and find that the volume of steep-slope and cirque-type glaciers is not very sensitive to changes in glacier area.

On roof geometry for urban wind energy exploitation in high-rise buildings

The European program HORIZON2020 aims to have 20% of electricity produced by renewable sources. The building sector represents 40% of the European Union energy consumption. Reducing energy consumption in buildings is therefore a priority for energy efficiency. The present investigation explores the most adequate roof shapes compatible with the placement of different types of small wind energy generators on high-rise buildings for urban wind energy exploitation. The wind flow around traditional state-of-the-art roof shapes is considered. In addition, the influence of the roof edge on the wind flow on high-rise buildings is analyzed. These geometries are investigated, both qualitatively and quantitatively, and the turbulence intensity threshold for horizontal axis wind turbines is considered. The most adequate shapes for wind energy exploitation are identified, studying vertical profiles of velocity, turbulent kinetic energy and turbulence intensity. Curved shapes are the most interesting building roof shapes from the wind energy exploitation point of view, leading to the highest speed-up and the lowest turbulence intensity.