Interactions between water and triacylglycerols may explain faster aging rates in stored germplasm at low temperatures

The purpose of this research is to explore the extent and significance of possible interacting factors on the viability of stored germplasm. Our work begins with characterizing the kinetics of TAG and water phase changes in peanut (Arachis hypogaea) and Papaya (Carica papaya) seeds equilibrated to different water contents and stored at temperatures between -5 and -80°C. Water and TAG phase was measured using a Perkin Elmer Differential Scanning Calorimeter. Cytoplasm ultra-structure was visualized without chemical fixatives using low temperature scanning electron microscopy (cryo-SEM) performed with a Zeiss DSN 960 scanning microscope equipped with a Cryotrans CT-1500 cold plate (Oxford, UK).

Estudios termodinámicos de los procesos de vitrificación en la crioconservación de germoplasma vegetal=Thermodynamic studies of vitrification processes in plant germplasm cryopreservation

En la actualidad, las técnicas de crioconservación poseen una importancia creciente para el almacenamiento a largo plazo de germoplasma vegetal. En las dos últimas décadas, estos métodos experimentaron un gran desarrollo y se han elaborado protocolos adecuados a diferentes sistemas vegetales, utilizando diversas estrategias como la vitrificación, la encapsulación-desecación con cuentas de alginato y el método de “droplet”-vitrificación. La presente tesis doctoral tiene como objetivo aumentar el conocimiento sobre los procesos implicados en los distintos pasos de un protocolo de crioconservación, en relación con el estado del agua presente en los tejidos y sus cambios, abordado mediante diversas técnicas biofísicas, principalmente calorimetría diferencial de barrido (DSC) y microscopía electrónica de barrido a baja temperatura (crio-SEM). En un primer estudio sobre estos métodos de crioconservación, se describen las fases de enfriamiento hasta la temperatura del nitrógeno líquido y de calentamiento hasta temperatura ambiente, al final del periodo de almacenamiento, que son críticas para la supervivencia del material crioconservado. Tanto enfriamiento como calentamiento deben ser realizados lo más rápidamente posible pues, aunque los bajos contenidos en agua logrados en etapas previas de los protocolos reducen significativamente las probabilidades de formación de hielo, éstas no son del todo nulas. En ese contexto, se analiza también la influencia de las velocidades de enfriamiento y calentamiento de las soluciones de crioconservación de plantas en sus parámetros termofísicos referente a la vitrificación, en relación su composición y concentración de compuestos. Estas soluciones son empleadas en la mayor parte de los protocolos actualmente utilizados para la crioconservación de material vegetal. Además, se estudia la influencia de otros factores que pueden determinar la estabilidad del material vitrificado, tales como en envejecimiento del vidrio. Se ha llevado a cabo una investigación experimental en el empleo del crio-SEM como una herramienta para visualizar el estado vítreo de las células y tejidos sometidos a los procesos de crioconservación. Se ha comparado con la más conocida técnica de calorimetría diferencial de barrido, obteniéndose resultados muy concordantes y complementarios. Se exploró también por estas técnicas el efecto sobre tejidos vegetales de la adaptación a bajas temperaturas y de la deshidratación inducida por los diferentes tratamientos utilizados en los protocolos. Este estudio permite observar la evolución biofísica de los sistemas en el proceso de crioconservación. Por último, se estudió la aplicación de películas de quitosano en las cuentas de alginato utilizadas en el protocolo de encapsulación. No se observaron cambios significativos en su comportamiento frente a la deshidratación, en sus parámetros calorimétricos y en la superficie de las cuentas. Su aplicación puede conferir propiedades adicionales prometedoras. ABSTRACT Currently, cryopreservation techniques have a growing importance for long term plant germplasm storage. These methods have undergone great progress during the last two decades, and adequate protocols for different plant systems have been developed, making use of diverse strategies, such as vitrification, encapsulation-dehydration with alginate beads and the dropletvitrification method. This PhD thesis has the goal of increasing the knowledge on the processes underlying the different steps of cryopreservation protocols, in relation with the state of water on tissues and its changes, approached through diverse biophysical techniques, especially differential scanning calorimetry (DSC) and low-temperature scanning electron microscopy (cryo-SEM). The processes of cooling to liquid nitrogen temperature and warming to room temperature, at the end of the storage period, critical for the survival of the cryopreserved material, are described in a first study on these cryopreservation methods. Both cooling and warming must be carried out as quickly as possible because, although the low water content achieved during previous protocol steps significantly reduces ice formation probability, it does not completely disappear. Within this context, the influence of plant vitrification solutions cooling and warming rate on their vitrification related thermophysical parameters is also analyzed, in relation to its composition and component concentration. These solutions are used in most of the currently employed plant material cryopreservation protocols. Additionally, the influence of other factors determining the stability of vitrified material is studied, such as glass aging. An experimental research work has been carried out on the use of cryo-SEM as a tool for visualizing the glassy state in cells and tissues, submitted to cryopreservation processes. It has been compared with the better known differential scanning calorimetry technique, and results in good agreement and complementary have been obtained. The effect on plant tissues of adaptation to low temperature and of the dehydration induced by the different treatments used in the protocols was explored also by these techniques. This study allows observation of the system biophysical evolution in the cryopreservation process. Lastly, the potential use of an additional chitosan film over the alginate beads used in encapsulation protocols was examined. No significant changes could be observed in its dehydration and calorimetric behavior, as well as in its surface aspect; its application for conferring additional properties to gel beads is promising.

Three-dimensional spatial distribution of synapses in the neocortex: A dual-beam electron microscopy study

In the cerebral cortex, most synapses are found in the neuropil, but relatively little is known about their 3-dimensional organization. Using an automated dual-beam electron microscope that combines focused ion beam milling and scanning electron microscopy, we have been able to obtain 10 three-dimensional samples with an average volume of 180 µm(3) from the neuropil of layer III of the young rat somatosensory cortex (hindlimb representation). We have used specific software tools to fully reconstruct 1695 synaptic junctions present in these samples and to accurately quantify the number of synapses per unit volume. These tools also allowed us to determine synapse position and to analyze their spatial distribution using spatial statistical methods. Our results indicate that the distribution of synaptic junctions in the neuropil is nearly random, only constrained by the fact that synapses cannot overlap in space. A theoretical model based on random sequential absorption, which closely reproduces the actual distribution of synapses, is also presented.

High-temperature mechanical properties of aluminium alloys reinforced with titanium diboride (TiB2) particles

The physical and mechanical properties of metal matrix composites were improved by the addition of reinforcements. The mechanical properties of particulate-reinforced metal-matrix composites based on aluminium alloys (6061 and 7015) at high temperatures were studied. Titanium diboride (TiB2) particles were used as the reinforcement. All the composites were produced by hot extrusion. The tensile properties and fracture characteristics of these materials were investigated at room temperature and at high temperatures to determine their ultimate strength and strain to failure. The fracture surface was analysed by scanning electron microscopy. TiB2 particles provide high stability of the aluminium alloys (6061 and 7015) in the fabrication process. An improvement in the mechanical behaviour was achieved by adding TiB2 particles as reinforcement in both the aluminium alloys. Adding TiB2 particles reduces the ductility of the aluminium alloys but does not change the microscopic mode of failure, and the fracture surface exhibits a ductile appearance with dimples formed by coalescence.

Enhanced iron gettering by short, optimized low-temperature annealing after phosphorus emitter diffusion for industrial silicon solar cell processing

The introduction of a low-temperature (LT) tail after P emitter diffusion was shown to lead to considerable improvements in electron lifetime and solar cell performance by different researchers. So far, the drawback of the investigated extended gettering treatments has been the lack of knowledge about optimum annealing times and temperatures and the important increase in processing time. In this manuscript, we calculate optimum annealing temperatures of Fe-contaminated Si wafers for different annealing durations. Subsequently, it is shown theoretically and experimentally that a relatively short LT tail of 15 min can lead to a significant reduction of interstitial Fe and an increase in electron lifetime. Finally, we calculate the potential improvement of solar cell efficiency when such a short-tail extended P diffusion gettering is included in an industrial fabrication process.

ESPINA: a tool for the automated segmentation and counting of synapses in large stacks of electron microscopy images

The synapses in the cerebral cortex can be classified into two main types, Gray’s type I and type II, which correspond to asymmetric (mostly glutamatergic excitatory) and symmetric (inhibitory GABAergic) synapses, respectively. Hence, the quantification and identification of their different types and the proportions in which they are found, is extraordinarily important in terms of brain function. The ideal approach to calculate the number of synapses per unit volume is to analyze 3D samples reconstructed from serial sections. However, obtaining serial sections by transmission electron microscopy is an extremely time consuming and technically demanding task. Using focused ion beam/scanning electron microscope microscopy, we recently showed that virtually all synapses can be accurately identified as asymmetric or symmetric synapses when they are visualized, reconstructed, and quantified from large 3D tissue samples obtained in an automated manner. Nevertheless, the analysis, segmentation, and quantification of synapses is still a labor intensive procedure. Thus, novel solutions are currently necessary to deal with the large volume of data that is being generated by automated 3D electron microscopy. Accordingly, we have developed ESPINA, a software tool that performs the automated segmentation and counting of synapses in a reconstructed 3D volume of the cerebral cortex, and that greatly facilitates and accelerates these processes.

Desarrollo y caracterización de un material celular de alta porosidad con base cementicia activada mediante agentes inorgánicos

Esta tesis ha estudiado los morteros celulares, centrándose en la experimentación con pastas de cemento aireadas (PCA) con polvo de aluminio como agente expansor. El objetivo es el desarrollo de un material cementicio con una baja conductividad térmica que sirva como aislamiento térmico. La naturaleza inorgánica del material lo hace incombustible, en contraste con las espumas poliméricas existentes en el mercado, cuya aplicación en cámaras ventiladas ha sido prohibida por normativas de construcción tanto a nivel nacional como internacional. Las posibles aplicaciones son con proyección neumática o en paneles prefabricados. Se han ensayado dos series de pastas de cemento con polvo de aluminio: - Serie WPC/CAC/CH. Mezcla de referencia con cemento blanco (WPC), cemento de aluminato cálcico (CAC) y cal aérea (CH) en proporción 5:1:4. - Serie OPC/CH. Mezcla de referencia con cemento portland con cenizas volantes (OPC) y cal aérea (CH) en proporción OPC/CH de 4:1 A las mezclas de referencia se le han añadido adiciones de metacaolín (MK) (10 y 20%) o sepiolita (SP) (1 y 2%) para observar el efecto que producen tanto en el mortero fresco como en el mortero endurecido. Se ha estudiado la reología de las pastas en estado fresco, analizando el proceso de expansión de las pastas, registrando los valores de tensión de fluencia, aire ocluido y temperatura durante la expansión. Con los valores obtenidos se ha discutido la influencia de las adiciones utilizadas en la cinética de corrosión del polvo de aluminio que genera la expansión, concluyendo que las adiciones puzolánicas (CV y MK) y la SP reducen mucho el periodo de inducción, lo que provoca poros más grandes y mayor cantidad de aire ocluido. Asimismo se ha analizado la relación entre la tensión de fluencia y el contenido de aire ocluido, deduciendo que a mayor tensión de fluencia en el momento de iniciarse la expansión, menor tamaño de poros y contenido de aire ocluido. Finalmente, se han obtenido las densidades y capacidades de retención de agua de los morteros frescos. Para caracterizar la red porosa de las pastas aireadas endurecidas, se obtuvieron tanto las densidades reales, netas, aparentes y relativas como las porosidades abiertas, cerradas y totales con ensayos hídricos. Finalmente se obtuvieron imágenes de los poros con tomografía axial computerizada para obtener las porosimetrías de las muestras. La caracterización de la red porosa ha servido para terminar de analizar lo observado en la evolución de la expansión del mortero fresco. Se ha analizado la influencia de la red porosa en la conductividad térmica, obtenida con caja caliente, comparándola con la existente en la literatura existente tanto de morteros celulares como de espumas poliméricas. Se concluye que los valores de conductividad térmica conseguida están en el mínimo posible para un material celular de base cementicia. La microestructura se ha estudiado con microscopía electrónica de barrido, difracción de rayos X y ensayos térmicos TG/ATD, observando que los productos de hidratación encontrados coinciden con los que se producen en morteros sin airear. Las imágenes SEM y los resultados de ultrasonidos han servido para analizar la presencia de microfisuras de retracción en las pastas aireadas, observando que en las muestras con adiciones de MK y SP, se reduce la presencia de microfisuras. ABSTRACT This thesis has studied cellular mortars, focusing in testing aerated cement pastes with aluminum powder as expansive agent. The purpose is the development of a cementitious material with low thermal conductivity that can be used as thermal isolation. Inorganic nature of this material makes it non-combustible, in contrast with polymeric foams in market, whose application in ventilated double skin façade systems has been banned by building standards, both domestically and internationally. Possible uses for this material are pneumatically sprayed applications and precast panels. Two series of batches with aluminum powder have been tested: - WPC/CAC/CH series. Reference paste with white portland cement (WPC), calcium aluminate cement (CAC) and lime (CH) with 5:1:4 ratio. - OPC/CH series. Reference paste with portland cement with fly ash (OPC) and lime (CH) with 4:1 ratio. Metakaolin (MK) (10 and 20%) or sepiolite (SP) (1 and 2%) additions were used in reference pastes to characterize the effect in fresh and hardened mortar. Rheology in fresh pastes was studied, expansion process of pastes was analyzed, recording yield stress, entrained air and temperature values during expansion. Recorded values were used to discuss influence of additions on reaction kinetics of aluminum powder corrosion, that produces expansion.. Conclusion is that pozzolanic additions (FA and MK) and SP greatly reduce induction period, producing bigger pores and more entrained air. Relation between yield stress and entrained air has been also analyzed, observing that the bigger yield stress at beginning of expansion, the smaller pores size and the lower entrained air values. Finally density and water retention of fresh mortars were obtained. Pore network in hardened aerated cement pastes was characterized by imbibition methods providing true, bulk and relative density, and providing also open, closed and total porosity. Finally, pore system imaging were obtained with computerized axial tomography to study porosimetry of specimens. Pore network characterization was useful to complete facts analysis observed in expansion of fresh mortars. Influence of pore network in thermal conductivity, checked in hot box, was analyzed comparing with those existing values in cellular mortar and polymeric foams researches. It was concluded that thermal conductivity values achieved are close to minimum possible in a cementitious cellular material. Microstructure was studied with Scanning Electron Microscopy, X-Ray Diffractometry and TG-DTA analysis, observing that hydration phases found, are those produced in non aerated mortar. SEM imaging and ultrasound results were useful to analyze shrinkage microcracks in aerated cement pastes, concluding that microcrack presence in specimens with MK and SP additions were reduced.

Mechanical behavior of tungsten-vanadium-lanthana alloys as function of temperature

The mechanical behavior of three tungsten (W) alloys with vanadium (V) and lanthana (La2O3) additions (W–4%V, W–1%La2O3, W–4%V–1%La2O3) processed by hot isostatic pressing (HIP) have been compared with pure-W to analyze the influence of the dopants. Mechanical characterization was performed by three point bending (TPB) tests in an oxidizing air atmosphere and temperature range between 77 (immersion tests in liquid nitrogen) and 1273 K, through which the fracture toughness, flexural strength, and yield strength as function of temperature were obtained. Results show that the V and La2O3 additions improve the mechanical properties and oxidation behavior, respectively. Furthermore, a synergistic effect of both dopants results in an extraordinary increase of the flexure strength, fracture toughness and resistance to oxidation compared to pure-W, especially at higher temperatures. In addition, a new experimental method was developed to obtain a very small notch tip radius (around 5–7 μm) and much more similar to a crack through the use of a new machined notch. The fracture toughness results were lower than those obtained with traditional machining of the notch, which can be explained with electron microscopy, observations of deformation in the rear part of the notch tip. Finally, scanning electron microscopy (SEM) examination of the microstructure and fracture surfaces was used to determine and analyze the relationship between the macroscopic mechanical properties and the micromechanisms of failure involved, depending on the temperature and the dispersion of the alloy.

Mechanical characterisation of tungsten-1wt.% yttrium oxide as a function of temperature and atmosphere

This study evaluates the mechanical behaviour of an Y2O3-dispersed tungsten (W) alloy and compares it to a pure W reference material. Both materials were processed via mechanical alloying (MA) and subsequent hot isostatic pressing (HIP). We performed non-standard three-point bending (TPB) tests in both an oxidising atmosphere and vacuum across a temperature range from 77 K, obtained via immersion in liquid nitrogen, to 1473 K to determine the mechanical strength, yield strength and fracture toughness. This research aims to evaluate how the mechanical behaviour of the alloy is affected by oxides formed within the material at high temperatures, primarily from 873 K, when the materials undergo a massive thermal degradation. The results indicate that the alloy is brittle to a high temperature (1473 K) under both atmospheres and that the mechanical properties degrade significantly above 873 K. We also used Vickers microhardness tests and the dynamic modulus by impulse excitation technique (IET) to determine the elastic modulus at room temperature. Moreover, we performed nanoindentation tests to determine the effect of size on the hardness and elastic modulus; however, no significant differences were found. Additionally, we calculated the relative density of the samples to assess the porosity of the alloy. Finally, we analysed the microstructure and fracture surfaces of the tested materials via field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). In this way, the relationship between the macroscopic mechanical properties and micromechanisms of failure could be determined based on the temperature and oxides formed

Self assembled and ordered group III nitride nanocolumnar structures for light emitting applications

El objetivo de este trabajo es un estudio profundo del crecimiento selectivo de nanoestructuras de InGaN por epitaxia de haces moleculares asistido por plasma, concentrandose en el potencial de estas estructuras como bloques constituyentes en LEDs de nueva generación. Varias aproximaciones al problema son discutidas; desde estructuras axiales InGaN/GaN, a estructuras core-shell, o nanoestructuras crecidas en sustratos con orientaciones menos convencionales (semi polar y no polar). La primera sección revisa los aspectos básicos del crecimiento auto-ensamblado de nanocolumnas de GaN en sustratos de Si(111). Su morfología y propiedades ópticas son comparadas con las de capas compactas de GaN sobre Si(111). En el caso de las columnas auto-ensambladas de InGaN sobre Si(111), se presentan resultados sobre el efecto de la temperatura de crecimiento en la incorporación de In. Por último, se discute la inclusión de nanodiscos de InGaN en las nanocolumnas de GaN. La segunda sección revisa los mecanismos básicos del crecimiento ordenado de nanoestructuras basadas en GaN, sobre templates de GaN/zafiro. Aumentando la relación III/V localmente, se observan cambios morfológicos; desde islas piramidales, a nanocolumnas de GaN terminadas en planos semipolares, y finalmente, a nanocolumnas finalizadas en planos c polares. Al crecer nanodiscos de InGaN insertados en las nanocolumnas de GaN, las diferentes morfologias mencionadas dan lugar a diferentes propiedades ópticas de los nanodiscos, debido al diferente carácter (semi polar o polar) de los planos cristalinos involucrados. La tercera sección recoge experimentos acerca de los efectos que la temperatura de crecimiento y la razón In/Ga tienen en la morfología y emisión de nanocolumnas ordenadas de InGaN crecidas sobre templates GaN/zafiro. En el rango de temperaturas entre 650 y 750 C, la incorporacion de In puede modificarse bien por la temperatura de crecimiento, o por la razón In/Ga. Controlar estos factores permite la optimización de la longitud de onda de emisión de las nanocolumnas de InGaN. En el caso particular de la generación de luz blanca, se han seguidos dos aproximaciones. En la primera, se obtiene emisión amarilla-blanca a temperatura ambiente de nanoestructuras donde la región de InGaN consiste en un gradiente de composiciones de In, que se ha obtenido a partir de un gradiente de temperatura durante el crecimiento. En la segunda, el apilamiento de segmentos emitiendo en azul, verde y rojo, consiguiendo la integración monolítica de estas estructuras en cada una de las nanocolumnas individuales, da lugar a emisores ordenados con un amplio espectro de emisión. En esta última aproximación, la forma espectral puede controlarse con la longitud (duración del crecimiento) de cada uno de los segmentos de InGaN. Más adelante, se presenta el crecimiento ordenado, por epitaxia de haces moleculares, de arrays de nanocolumnas que son diodos InGaN/GaN cada una de ellas, emitiendo en azul (441 nm), verde (502 nm) y amarillo (568 nm). La zona activa del dispositivo consiste en una sección de InGaN, de composición constante nominalmente y longitud entre 250 y 500 nm, y libre de defectos extendidos en contraste con capas compactas de InGaN de similares composiciones y espesores. Los espectros de electroluminiscencia muestran un muy pequeño desplazamiento al azul al aumentar la corriente inyectada (desplazamiento casi inexistente en el caso del dispositivo amarillo), y emisiones ligeramente más anchas que en el caso del estado del arte en pozos cuánticos de InGaN. A continuación, se presenta y discute el crecimiento ordenado de nanocolumnas de In(Ga)N/GaN en sustratos de Si(111). Nanocolumnas ordenadas emitiendo desde el ultravioleta (3.2 eV) al infrarrojo (0.78 eV) se crecieron sobre sustratos de Si(111) utilizando una capa compacta (“buffer”) de GaN. La morfología y eficiencia de emisión de las nanocolumnas emitiendo en el rango espectral verde pueden ser mejoradas ajustando las relaciones In/Ga y III/N, y una eficiencia cuántica interna del 30% se deriva de las medidas de fotoluminiscencia en nanocolumnas optimizadas. En la siguiente sección de este trabajo se presenta en detalle el mecanismo tras el crecimiento ordenado de nanocolumnas de InGaN/GaN emitiendo en el verde, y sus propiedades ópticas. Nanocolumnas de InGaN/GaN con secciones largas de InGaN (330-830 nm) se crecieron tanto en sustratos GaN/zafiro como GaN/Si(111). Se encuentra que la morfología y la distribución espacial del In dentro de las nanocolumnas dependen de las relaciones III/N e In/Ga locales en el frente de crecimiento de las nanocolumnas. La dispersión en el contenido de In entre diferentes nanocolumnas dentro de la misma muestra es despreciable, como indica las casi identicas formas espectrales de la catodoluminiscencia de una sola nanocolumna y del conjunto de ellas. Para las nanocolumnas de InGaN/GaN crecidas sobre GaN/Si(111) y emitiendo en el rango espectral verde, la eficiencia cuántica interna aumenta hasta el 30% al disminuir la temperatura de crecimiento y aumentar el nitrógeno activo. Este comportamiento se debe probablemente a la formación de estados altamente localizados, como indica la particular evolución de la energía de fotoluminiscencia con la temperatura (ausencia de “s-shape”) en muestras con una alta eficiencia cuántica interna. Por otro lado, no se ha encontrado la misma dependencia entre condiciones de crecimiento y efiencia cuántica interna en las nanoestructuras InGaN/GaN crecidas en GaN/zafiro, donde la máxima eficiencia encontrada ha sido de 3.7%. Como alternativa a las nanoestructuras axiales de InGaN/GaN, la sección 4 presenta resultados sobre el crecimiento y caracterización de estructuras core-shell de InGaN/GaN, re-crecidas sobre arrays de micropilares de GaN fabricados por ataque de un template GaN/zafiro (aproximación top-down). El crecimiento de InGaN/GaN es conformal, con componentes axiales y radiales en el crecimiento, que dan lugar a la estructuras core-shell con claras facetas hexagonales. El crecimiento radial (shell) se ve confirmado por medidas de catodoluminiscencia con resolución espacial efectuadas en un microscopio electrónico de barrido, asi como por medidas de microscopía de transmisión de electrones. Más adelante, el crecimiento de micro-pilares core-shell de InGaN se realizó en pilares GaN (cores) crecidos selectivamente por epitaxia de metal-orgánicos en fase vapor. Con el crecimiento de InGaN se forman estructuras core-shell con emisión alrededor de 3 eV. Medidas de catodoluminiscencia resuelta espacialmente indican un aumento en el contenido de indio del shell en dirección a la parte superior del pilar, que se manifiesta en un desplazamiento de la emisión de 3.2 eV en la parte inferior, a 3.0 eV en la parte superior del shell. Este desplazamiento está relacionado con variaciones locales de la razón III/V en las facetas laterales. Finalmente, se demuestra la fabricación de una estructura pin basada en estos pilares core-shell. Medidas de electroluminiscencia resuelta espacialmente, realizadas en pilares individuales, confirman que la electroluminiscencia proveniente del shell de InGaN (diodo lateral) está alrededor de 3.0 eV, mientras que la emisión desde la parte superior del pilar (diodo axial) está alrededor de 2.3 eV. Para finalizar, se presentan resultados sobre el crecimiento ordenado de GaN, con y sin inserciones de InGaN, en templates semi polares (GaN(11-22)/zafiro) y no polares (GaN(11-20)/zafiro). Tras el crecimiento ordenado, gran parte de los defectos presentes en los templates originales se ven reducidos, manifestándose en una gran mejora de las propiedades ópticas. En el caso de crecimiento selectivo sobre templates con orientación GaN(11-22), no polar, la formación de nanoestructuras con una particular morfología (baja relación entre crecimiento perpedicular frente a paralelo al plano) permite, a partir de la coalescencia de estas nanoestructuras, la fabricación de pseudo-templates no polares de GaN de alta calidad. ABSTRACT The aim of this work is to gain insight into the selective area growth of InGaN nanostructures by plasma assisted molecular beam epitaxy, focusing on their potential as building blocks for next generation LEDs. Several nanocolumn-based approaches such as standard axial InGaN/GaN structures, InGaN/GaN core-shell structures, or InGaN/GaN nanostructures grown on semi- and non-polar substrates are discussed. The first section reviews the basics of the self-assembled growth of GaN nanocolumns on Si(111). Morphology differences and optical properties are compared to those of GaN layer grown directly on Si(111). The effects of the growth temperature on the In incorporation in self-assembled InGaN nanocolumns grown on Si(111) is described. The second section reviews the basic growth mechanisms of selectively grown GaNbased nanostructures on c-plane GaN/sapphire templates. By increasing the local III/V ratio morphological changes from pyramidal islands, to GaN nanocolumns with top semi-polar planes, and further to GaN nanocolumns with top polar c-planes are observed. When growing InGaN nano-disks embedded into the GaN nanocolumns, the different morphologies mentioned lead to different optical properties, due to the semipolar and polar nature of the crystal planes involved. The third section reports on the effect of the growth temperature and In/Ga ratio on the morphology and light emission characteristics of ordered InGaN nanocolumns grown on c-plane GaN/sapphire templates. Within the growth temperature range of 650 to 750oC the In incorporation can be modified either by the growth temperature, or the In/Ga ratio. Control of these factors allows the optimization of the InGaN nanocolumns light emission wavelength. In order to achieve white light emission two approaches are used. First yellow-white light emission can be obtained at room temperature from nanostructures where the InGaN region is composition-graded by using temperature gradients during growth. In a second approach the stacking of red, green and blue emitting segments was used to achieve the monolithic integration of these structures in one single InGaN nanocolumn leading to ordered broad spectrum emitters. With this approach, the spectral shape can be controlled by changing the thickness of the respective InGaN segments. Furthermore the growth of ordered arrays of InGaN/GaN nanocolumnar light emitting diodes by molecular beam epitaxy, emitting in the blue (441 nm), green (502 nm), and yellow (568 nm) spectral range is reported. The device active region, consisting of a nanocolumnar InGaN section of nominally constant composition and 250 to 500 nm length, is free of extended defects, which is in strong contrast to InGaN layers (planar) of similar composition and thickness. Electroluminescence spectra show a very small blue shift with increasing current, (almost negligible in the yellow device) and line widths slightly broader than those of state-of-the-art InGaN quantum wells. Next the selective area growth of In(Ga)N/GaN nanocolumns on Si(111) substrates is discussed. Ordered In(Ga)N/GaN nanocolumns emitting from ultraviolet (3.2 eV) to infrared (0.78 eV) were then grown on top of GaN-buffered Si substrates. The morphology and the emission efficiency of the In(Ga)N/GaN nanocolumns emitting in the green could be substantially improved by tuning the In/Ga and total III/N ratios, where an estimated internal quantum efficiency of 30 % was derived from photoluminescence data. In the next section, this work presents a study on the selective area growth mechanisms of green-emitting InGaN/GaN nanocolumns and their optical properties. InGaN/GaN nanocolumns with long InGaN sections (330-830nm) were grown on GaN/sapphire and GaN-buffered Si(111). The nanocolumn’s morphology and spatial indium distribution is found to depend on the local group (III)/N and In/Ga ratios at the nanocolumn’s top. A negligible spread of the average indium incorporation among different nanostructures is found as indicated by similar shapes of the cathodoluminescence spectra taken from single nanocolumns and ensembles of nanocolumns. For InGaN/GaN nanocolumns grown on GaN-buffered Si(111), all emitting in the green spectral range, the internal quantum efficiency increases up to 30% when decreasing growth temperature and increasing active nitrogen. This behavior is likely due to the formation of highly localized states, as indicated by the absence of a complete s-shape behavior of the PL peak position with temperature (up to room temperature) in samples with high internal quantum efficiency. On the other hand, no dependence of the internal quantum efficiency on the growth conditions is found for InGaN/GaN nanostructures grown on GaN/sapphire, where the maximum achieved efficiency is 3.7%. As alternative to axial InGaN/GaN nanostructures, section 4 reports on the growth and characterization of InGaN/GaN core-shell structures on an ordered array of top-down patterned GaN microrods etched from a GaN/sapphire template. Growth of InGaN/GaN is conformal, with axial and radial growth components leading to core-shell structures with clear hexagonal facets. The radial InGaN growth (shell) is confirmed by spatially resolved cathodoluminescence performed in a scanning electron microscopy as well as in scanning transmission electron microscopy. Furthermore the growth of InGaN core-shell micro pillars using an ordered array of GaN cores grown by metal organic vapor phase epitaxy as a template is demonstrated. Upon InGaN overgrowth core-shell structures with emission at around 3.0 eV are formed. With spatially resolved cathodoluminescence, an increasing In content towards the pillar top is found to be present in the InGaN shell, as indicated by a shift of CL peak position from 3.2 eV at the shell bottom to 3.0 eV at the shell top. This shift is related to variations of the local III/V ratio at the side facets. Further, the successful fabrication of a core-shell pin diode structure is demonstrated. Spatially resolved electroluminescence measurements performed on individual micro LEDs, confirm emission from the InGaN shell (lateral diode) at around 3.0 eV, as well as from the pillar top facet (axial diode) at around 2.3 eV. Finally, this work reports on the selective area growth of GaN, with and without InGaN insertion, on semi-polar (11-22) and non-polar (11-20) templates. Upon SAG the high defect density present in the GaN templates is strongly reduced as indicated by TEM and a dramatic improvement of the optical properties. In case of SAG on non-polar (11-22) templates the formation of nanostructures with a low aspect ratio took place allowing for the fabrication of high-quality, non-polar GaN pseudo-templates by coalescence of the nanostructures.

Aplicación de la celulosa bacteriana a la restauración del patrimonio bibliográfico y documental en papel

La preservación del patrimonio bibliográfico y documental en papel es uno de los mayores retos a los que se enfrentan bibliotecas y archivos de todo el mundo. La búsqueda de soluciones al problema del papel degradado ha sido abordada históricamente desde dos líneas de trabajo predominantes: la conservación de estos documentos mediante la neutralización de los ácidos presentes en ellos con agentes alcalinos, y su restauración mediante el método de laminación fundamentalmente con papel de origen vegetal. Sin embargo, no se ha explorado con éxito la posibilidad de reforzar la celulosa dañada, y el problema sigue sin encontrar una solución satisfactoria. Hasta el día de hoy, el desarrollo de tratamientos basados en biotecnología en la conservación del patrimonio documental ha sido muy escaso, aunque la capacidad de ciertas bacterias de producir celulosa lleva a plantear su uso en el campo de la conservación y restauración del papel. La celulosa bacteriana (CB) es químicamente idéntica a la celulosa vegetal, pero su organización macroscópica es diferente. Sus propiedades únicas (alto grado de cristalinidad, durabilidad, resistencia y biocompatibilidad) han hecho de este material un excelente recurso en diferentes campos. En el desarrollo de esta tesis se ha estudiado el uso de la celulosa bacteriana, de alta calidad, generada por Gluconacetobacter sucrofermentans CECT 7291, para restaurar documentos deteriorados y consolidar los que puedan estar en peligro de degradación, evitando así su destrucción y proporcionando al papel que se restaura unas buenas propiedades mecánicas, ópticas y estructurales. Se desarrollan asimismo protocolos de trabajo que permitan la aplicación de dicha celulosa. En primer lugar se seleccionó el medio de cultivo que proporcionó una celulosa adecuada para su uso en restauración. Para ello se evaluó el efecto que tienen sobre la celulosa generada las fuentes de carbono y nitrógeno del medio de cultivo, manteniendo como parámetros fijos la temperatura y el pH inicial del medio, y efectuando los ensayos en condiciones estáticas. Se evaluó, también, el efecto que tiene en la CB la adición de un 1% de etanol al medio de cultivo. Las capas de celulosa se recolectaron a cuatro tiempos distintos, caracterizando en cada uno de ellos el medio de cultivo (pH y consumo de fuente de carbono), y las capas de CB (pH, peso seco y propiedades ópticas y mecánicas). La mejor combinación de fuentes de carbono y nitrógeno resultó ser fructosa más extracto de levadura y extracto de maíz, con o sin etanol, que proporcionaban una buena relación entre la producción de celulosa y el consumo de fuente de carbono, y que generaban una capa de celulosa resistente y homogénea. La adición de etanol al medio de cultivo, si bien aumentaba la productividad, causaba un descenso apreciable de pH. Las capas de CB obtenidas con los medios de cultivo optimizados se caracterizaron en términos de sus índices de desgarro y estallido, propiedades ópticas, microscopía electrónica de barrido (SEM), difracción de rayos-X, espectroscopía infrarroja con transformada de Fourier (FTIR), grado de polimerización, ángulos de contacto estáticos y dinámicos, y porosimetría de intrusión de mercurio. Por otro lado hay que tener en cuenta que el material restaurado debe ser estable con el tiempo. Por ello esta misma caracterización se efectuó tras someter a las capas de CB a un proceso de envejecimiento acelerado. Los resultados mostraron que la CB resultante tiene un elevado índice de cristalinidad, baja porosidad interna, buenas propiedades mecánicas, y alta estabilidad en el tiempo. Para desarrollar los protocolos de trabajo que permitan la restauración con esta celulosa optimizada, se comienzó con un proceso de selección de los papeles que van a ser restaurados. Se eligieron tres tipos de papeles modelo, hechos con pasta mecánica, química y filtro (antes y después de ser sometidos a un proceso de envejecimiento acelerado), y tres libros viejos adquiridos en el mercado de segunda mano. Estos ejemplares a restaurar se caracterizaron también en términos de sus propiedades mecánicas y fisicoquímicas. El primer protocolo de restauración con CB que se evaluó fue el denominado laminación. Consiste en aplicar un material de refuerzo al documento mediante el uso de un adhesivo. Se seleccionó para ello la CB producida en el medio de cultivo optimizado con un 1% de etanol. Se aplicó un método de purificación alcalino (1 hora a 90 °C en NaOH al 1%) y como adhesivo se seleccionó almidón de trigo. El proceso de laminación se efectuó también con papel japonés (PJ), un material habitualmente utilizado en conservación, para comparar ambos materiales. Se concluyó que no hay diferencias significativas en las características estudiadas entre los dos tipos de materiales de refuerzo. Se caracterizó el material reforzado y, también, después de sufrir un proceso de envejecimiento acelerado. Los papeles laminados con CB mostraban diferencias más marcadas en las propiedades ópticas que los restaurados con PJ, con respecto a los originales. Sin embargo, el texto era más legible cuando el material de restauración era la CB. La mojabilidad disminuía con ambos tipos de refuerzo, aunque en los papeles laminados con CB de manera más marcada e independiente del material a restaurar. Esto se debe a la estructura cerrada de la CB, que también conduce a una disminución en la permeabilidad al aire. Este estudio sugiere que la CB mejora la calidad del papel deteriorado, sin alterar la información que contiene, y que esta mejora se mantiene a lo largo del tiempo. Por tanto, la CB puede ser utilizada como material de refuerzo para laminar, pudiendo ser más adecuada que el PJ para ciertos tipos de papeles. El otro método de restauración que se estudió fue la generación in situ de la CB sobre el papel a restaurar. Para ello se seleccionó el medio de cultivo sin etanol, ya que el descenso de pH que causaba su presencia podría dañar el documento a restaurar. El método de purificación elegido fue un tratamiento térmico (24 horas a 65 °C), menos agresivo para el material a restaurar que el tratamiento alcalino. Se seleccionó la aplicación del medio de cultivo con la bacteria mediante pincel sobre el material a restaurar. Una vez caracterizado el material restaurado, y éste mismo tras sufrir un proceso de envejecimiento acelerado, se concluyó que no hay modificación apreciable en ninguna característica, salvo en la permeabilidad al aire, que disminuye de manera muy evidente con la generación de CB, dando lugar a un material prácticamente impermeable al aire. En general se puede concluir que ha quedado demostrada la capacidad que tiene la celulosa generada por la bacteria Gluconacetobacter sucrofermentans CECT 7291 para ser utilizada como material de refuerzo en la restauración del patrimonio documental en papel. Asimismo se han desarrollado dos métodos de aplicación, uno ex situ y otro in situ, para efectuar esta tarea de restauración. ABSTRACT The preservation of bibliographic and documentary heritage is one of the biggest challenges that libraries and archives around the world have to face. The search for solutions to the problem of degraded paper has historically been focused from two predominants lines of work: the conservation of these documents by the neutralization of acids in them with alkaline agents, and their restoration by lining them with, basically, cellulose from vegetal sources. However, the possibility of strengthening the damaged cellulose has not been successfully explored, and the problem still persists. Until today, the development of biotechnology-based treatments in documentary heritage conservation has been scarce, although the ability of certain bacteria to produce cellulose takes to propose its use in the field of conservation and restoration of paper. The bacterial cellulose (BC) is chemically identical to the plant cellulose, but its macroscopic organization is different. Its unique properties (high degree of crystallinity, durability, strength and biocompatibility), makes it an excellent resource in different fields. The use of high-quality BC generated by Gluconacetobacter sucrofermentans CECT 7291 to restore damaged documents and to consolidate those that may be at risk of degradation, has been studied in this thesis, trying to prevent the document destruction, and to get reinforced papers with good mechanical, optical and structural properties. Protocols that allow the implementation of the BC as a reinforcing material were also developed. First of all, in order to select the culture medium that provides a cellulose suitable for its use in restoration, it has been evaluated the effect that the carbon and nitrogen sources from the culture medium have on the generated BC, keeping the temperature and the initial pH of the medium as fixed parameters, and performing the culture without shaking. The effect of the addition of 1% ethanol to the culture medium on BC properties was also evaluated. The cellulose layers were collected at four different times, characterizing in all of them the culture medium (pH and carbon source consumption), and the BC sheets (pH, dry weight and optical and mechanical properties). The best combination of carbon and nitrogen sources proved to be fructose plus yeast extract and corn steep liquor, with or without ethanol, which provided a good balance between the cellulose production and the consumption of carbon source, and generating BC sheets homogeneous and resistant. The addition of ethanol to the culture medium increased productivity but caused a noticeable decrement in pH. The BC layers generated with these optimized culture media, have been characterized in terms of tear and burst index, optical properties, scanning electron microscopy (SEM), X-ray diffraction, infrared Fourier transform spectroscopy (FTIR), polymerization degree, static and dynamic contact angles, and mercury intrusion porosimetry. Moreover it must be kept in mind that the restored materials should be stable over time. Therefore, the same characterization was performed after subjecting the layers of BC to an accelerated aging process. The results showed that the BC sheets obtained have a high crystallinity index, low internal porosity, good mechanical properties, and high stability over time. To develop working protocols to use this optimized BC in paper restoration, the first step was to select the samples to restore. Three types of model papers, made from mechanical pulp, chemical pulp and filter paper (before and after an accelerated aging process), and three old books purchased in the second hand market, were chosen. These specimens to be restored were also characterized in terms of its mechanical and physicochemical properties. The first protocol of restoration with BC to be evaluated is called linning. It consists on applying a reinforcing material to the document using an adhesive. The BC produced in the optimized culture medium with 1% ethanol was selected. An alkali purification method (1 hour at 90 °C in 1% NaOH) was applied, and wheat starch was selected as adhesive. The linning process was also carried out with Japanese paper (JP), a material commonly used in conservation, in order to compare both materials. It was concluded that there are no significant differences in the characteristics studied of the two types of reinforcing materials. The reinforced materials were characterized before and after undergoing to an accelerated aging. Papers lined with BC showed more marked differences in the optical properties that papers restored with JP. However, the text was more readable when BC was the reinforcing material. Wettability decreased with both types of reinforcement, although in the papers linned with BC it happened more marked and independently of the sample to restore. This is due to the closed structure of BC, which also leads to a decrement in air permeance. This study suggests that BC improves the deteriorated paper quality, without altering the information on it, and that this improvement is maintained over time. Therefore, the BC may be used as reinforcing material for linning, being more suitable than the JP to restore certain types of papers. The other restoration method to be evaluated was the in situ generation of BC over the paper to restore. For this purpose the culture medium without ethanol was selected, as the pH decrement caused by his presence would damage the document to restore. As purification method a heat treatment (24 hours at 65 °C) was chosen, less aggressive to the material to restore than the alkaline treatment. It was decided to apply the culture medium with the bacteria onto the material to restore with a brush. The reinforced material was characterized before and after an accelerated aging process. It was concluded that there was no substantial change in any characteristic, except for air permeance, which decreases very sharply after the generation of BC, getting a substantially air impermeable material. In general, it can be concluded that the ability of BC produced by Gluconacetobacter sucrofermentans CECT 7291 for its use as a reinforcing material in the restoration of paper documentary heritage, has been demonstrated. Also, two restoration methods, one ex situ and another in situ have been developed.

The effects of tantalum addition on the microtexture and mechanical behaviour of tungsten for ITER applications

Tungsten (W) and its alloys are very promising materials for producing plasma-facing components (PFCs) in the fusion power reactors of the near future, even as a structural part in them. However, whereas the properties of pure tungsten are suitable for a PFC, its structural applications are still limited due to its low toughness, ductile to brittle transition temperature and recrystallization behaviour. Therefore, many efforts have been made to improve its performance by alloying tungsten with other elements. Hence, in this investigation, the thermo-mechanical performance of two new tungsten-tantalum materials has been evaluated. Materials with We5wt.%Ta and We15wt.%Ta were processed by mechanical alloying (MA) and later consolidation by hot isostatic pressing (HIP), with distinct settings for each composition. Thus, it was possible to determine the relationship between the microstructure and the addition of Ta with the macroscopic mechanical properties. These were measured by means of hardness, flexural strength and fracture toughness, in the temperature range of 300e1473 K. The microstructure and the fracture surfaces features of the tested materials were analysed by Field Emission Scanning Electron Microscopy (FESEM).