Hysteresis phenomena in transverse galloping of triangular cross-section bodies

Transverse galloping is a type of aeroelastic instability characterised by large amplitude, low frequency oscillation of a structure in the direction normal to the mean wind direction. It normally appears in bodies with small stiffness and structural damping, provided the incident flow velocity is high enough. In the simplest approach transverse galloping can be considered as a one-degree-of-freedom oscillator subjected to aerodynamic forces, which in turn can be described by using a quasi-steady description. In this frame it has been demonstrated that hysteresis phenomena in transverse galloping is related to the existence of inflection points in the curve giving the dependence with the angle of attack of the aerodynamic coefficient normal to the incident flow. Aiming at experimentally checking such a relationship between these inflection points and hysteresis, wind tunnel experiments have been conducted. Experiments have been restricted to isosceles triangular cross-section bodies, whose galloping behaviour is well documented. Experimental results show that, according to theoretical predictions, hysteresis takes place at the angles of attack where there are inflection points in the lift coefficient curve, provided that the body is prone to gallop at these angles of attack.

Global Stability Analysis of Turbulent Transonic Flows on Airfoil geometries

La aparición de inestabilidades en un flujo es un problema importante que puede afectar a algunas aplicaciones aerodinámicas. De hecho existen diferentes tipos de fenómenos no-estacionarios que actualmente son tema de investigación; casos como la separación a altos ángulos de ataque o el buffet transónico son dos ejemplos de cierta relevancia. El análisis de estabilidad global permite identificar la aparición de dichas condiciones inestables, proporcionando información importante sobre la región donde la inestabilidad es dominante y sobre la frecuencia del fenómeno inestable. La metodología empleada es capaz de calcular un flujo base promediado mediante una discretización con volúmenes finitos y posteriormente la solución de un problema de autovalores asociado a la linealización que aparece al perturbar el flujo base. El cálculo numérico se puede dividir en tres pasos: primero se calcula una solución estacionaria para las ecuaciones RANS, luego se extrae la matriz del Jacobiano que representa el problema linealizado y finalmente se deriva y se resuelve el problema de autovalores generalizado mediante el método iterativo de Arnoldi. Como primer caso de validación, la técnica descrita ha sido aplicada a un cilindro circular en condiciones laminares para detectar el principio de las oscilaciones de los vórtices de von Karman, y se han comparado los resultados con experimentos y cálculos anteriores. La parte más importante del estudio se centra en el análisis de flujos compresibles en régimen turbulento. La predicción de la aparición y la progresión de flujo separado a altos ángulos de ataque se han estudiado en el perfil NACA0012 en condiciones tanto subsónicas como supersónicas y en una sección del ala del A310 en condiciones de despegue. Para todas las geometrías analizadas, se ha podido observar que la separación gradual genera la aparición de un modo inestable específico para altos ángulos de ataque siempre mayores que el ángulo asociado al máximo coeficiente de sustentación. Además, se ha estudiado el problema adjunto para obtener información sobre la zona donde una fuerza externa provoca el máximo cambio en el campo fluido. El estudio se ha completado calculando el mapa de sensibilidad estructural y localizando el centro de la inestabilidad. En el presente trabajo de tesis se ha analizado otro importante fenómeno: el buffet transónico. En condiciones transónicas, la interacción entre la onda de choque y la capa límite genera una oscilación de la posición de la onda de choque y, por consiguiente, de las fuerzas aerodinámicas. El conocimiento de las condiciones críticas y su origen puede ayudar a evitar la oscilación causada por estas fuerzas. Las condiciones para las cuales comienza la inestabilidad han sido calculadas y comparadas con trabajos anteriores. Por otra parte, los resultados del correspondiente problema adjunto y el mapa de sensibilidad se han obtenido por primera vez para el buffet, indicando la región del dominio que sera necesario modificar para crear el mayor cambio en las propiedades del campo fluido. Dado el gran consumo de memoria requerido para los casos 3D, se ha realizado un estudio sobre la reducción del domino con la finalidad de reducirlo a la región donde está localizada la inestabilidad. La eficacia de dicha reducción de dominio ha sido evaluada investigando el cambio en la dimensión de la matriz del Jacobiano, no resultando muy eficiente en términos del consumo de memoria. Dado que el buffet es un problema en general tridimensional, el análisis TriGlobal de una geometría 3D podría considerarse el auténtico reto futuro. Como aproximación al problema, un primer estudio se ha realizado empleando una geometría tridimensional extruida del NACA00f2. El cálculo del flujo 3D y, por primera vez en casos tridimensionales compresibles y turbulentos, el análisis de estabilidad TriGlobal, se han llevado a cabo. La comparación de los resultados obtenidos con los resultados del anterior modelo 2D, ha permitido, primero, verificar la exactitud del cálculo 2D realizado anteriormente y también ha proporcionado una estimación del consumo de memoria requerido para el caso 3D. ABSTRACT Flow unsteadiness is an important problem in aerodynamic applications. In fact, there are several types of unsteady phenomena that are still at the cutting edge of research in the field; separation at high angles of attack and transonic buffet are two important examples. Global Stability Analysis can identify the unstable onset conditions, providing important information about the instability location in the domain and the frequency of the unstable phenomenon. The methodology computes a base flow averaged state based on a finite volume discretization and a solution for a generalized eigenvalue problem corresponding to the perturbed linearized equations. The numerical computation is then performed in three steps: first, a steady solution for the RANS equation is computed; second, the Jacobian matrix that represents the linearized problem is obtained; and finally, the generalized eigenvalue problem is derived and solved with an Arnoldi iterative method. As a first validation test, the technique has been applied on a laminar circular cylinder in order to detect the von Karman vortex shedding onset, comparing the results with experiments and with previous calculations. The main part of the study focusses on turbulent and compressible cases. The prediction of the origin and progression of separated flows at high angles of attack has been studied on the NACA0012 airfoil at subsonic and transonic conditions and for the A310 airfoil in take-off configuration. For all the analyzed geometries, it has been found that gradual separation generates the appearance of one specific unstable mode for angles of attack always greater than the ones related to the maximum lift coefficient. In addition, the adjoint problem has been studied to suggest the location of an external force that results in the largest change to the flow field. From the direct and the adjoint analysis the structural sensitivity map has been computed and the core of the instability has been located. The other important phenomenon analyzed in this work is the transonic buffet. In transonic conditions, the interaction between the shock wave and the boundary layer leads to an oscillation of the shock location and, consequently, of the aerodynamic forces. Knowing the critical operational conditions and its origin can be helpful in preventing such fluctuating forces. The instability onset has then been computed and compared with the literature. Moreover, results of the corresponding adjoint problem and a sensitivity map have been provided for the first time for the buffet problem, indicating the region that must be modified to create the biggest change in flow field properties. Because of the large memory consumption required when a 3D case is approached, a domain reduction study has been carried out with the aim of limiting the domain size to the region where the instability is located. The effectiveness of the domain reduction has been evaluated by investigating the change in the Jacobian matrix size, not being very efficient in terms of memory consumption. Since buffet is a three-dimensional problem, TriGlobal stability analysis can be seen as a future challenge. To approximate the problem, a first study has been carried out on an extruded three-dimensional geometry of the NACA0012 airfoil. The 3D flow computation and the TriGlobal stability analysis have been performed for the first time on a compressible and turbulent 3D case. The results have been compared with a 2D model, confirming that the buffet onset evaluated in the 2D case is well detected. Moreover, the computation has given an indication about the memory consumption for a 3D case.

Estudio y validación experimental del efecto de aire interno en un perfil aerodinámico hueco

La presente investigación se llevó a cabo en la Universidad Politécnica de Madrid (España) conjuntamente con la Universidad Nacional Experimental del Táchira (Venezuela). El estudio consistió en diseñar una cavidad interna dentro del perfil aerodinámico 2415-3s, el cual fue desarrollado en la Universidad Técnica Checa (Praga, República Checa). Se realizó un estudio computacional, mediante la técnica del CFD, de diferentes modelos de cavidades internas en este perfil, para seleccionar el diseño más adecuado, fabricando un prototipo en 3D; logrando de esta manera validar la simulación computacional con los datos experimentales obtenidos con los ensayos en el túnel de viento AF6109 de la Universidad Nacional Experimental del Táchira. También se aplicaron técnicas de visualización en el túnel de viento, como líneas de corriente de humo y películas de aceite sobre el perfil aerodinámico. Dicho procedimiento permitió corroborar la validación de la simulación computacional. El perfil aerodinámico seleccionado se denominó 2415-3s-TC, cuya característica principal consiste en tres canales independientes entre sí, alojados dentro de la cavidad interna, permitiendo que el flujo de aire forzado a través de la cavidad, cambiara de dirección, para desembocar lo más tangencialmente, así como, lo más perpendicularmente posible al escalón del perfil aerodinámico 2415-3s. Esta configuración de diseñó permitió elevar el coeficiente de sustentación para ángulos de ataque mayores a 8º, así como para ángulos cercanos al ángulo crítico. ABSTRACT This research was conducted at the Polytechnic University of Madrid (Spain) together with the National Experimental University of Táchira (Venezuela). The study was to design an internal cavity within the airfoil 2415-3s, which was developed in the Czech Technical University (Prague, Czech Republic). A computational study was performed using CFD technique, different models of internal cavities in the profile to select the most appropriate design, manufacturing a prototype 3D; thus achieving validate the computer simulation with experimental data obtained from the tests in the wind tunnel AF6109 of the National Experimental University of Táchira. Visualization techniques were also applied in the wind tunnel, as streamlines smoke and oil films on the airfoil. This procedure corroborated validation of computational simulation. The airfoil selected denominated 2415-3s-TC, whose main characteristic consists of three independent channels each other, housed within the inner cavity, allowing the forced air flow through the cavity, change direction, to lead as more tangentially and, as perpendicular as possible to the step 2415-3s aerofoil. This configuration designed allowed increasing the lift coefficient for higher angles of attack to 8º, and for angles near the critical angle.

Generating Scale-free Networks with Adjustable Clustering Coefficient Via Random Walks

This paper presents an algorithm for generating scale-free networks with adjustable clustering coefficient. The algorithm is based on a random walk procedure combined with a triangle generation scheme which takes into account genetic factors; this way, preferential attachment and clustering control are implemented using only local information. Simulations are presented which support the validity of the scheme, characterizing its tuning capabilities.

Estabilidad de un buque ultra heavy lift carrier

Se plantea la posible demanda en un futuro del transporte de grandes plataformas petrolíferas semisumergibles de más de 70.000 t de peso, para perforaciones a más de 10.000 pies de profundidad. Estudia la estabilidad de buques Heavy Lift Carrier con mangas atípicas, capaces de transportar estas cargas, y en algunos casos sobresaliendo por sus amuras. Para esto se: 1. Estudia y genera posibles carenas, su compartimentación y lastre para la inmersión o emersión de la cubierta de intemperie, a más de 10 m de profundidad para tomar o dejar la carga, optimizando el proceso. 2. Analiza la estabilidad del buque tanto en inmersión/emersión y navegación, con máximas cargas y con altos centros de gravedad, y establece ábacos de estabilidad límite en función de los parámetros del buque. 3. Plantea la corrección de estabilidad excesiva del buque en condiciones de navegación para evitar las excesivas aceleraciones. Los resultados obtenidos aportan ábacos que permiten, en función de los parámetros carga a transportar (Zg max) - Peso Carga), elegir el buque más adecuado, capaz de efectuar la inmersión, emersión, y navegación, y plantea acciones futuras de investigación. ABSTRACT This work raises the potential demand in the future, to transport large semisubmersible oil rigs over 70,000 tonnes of weight for drilling to 10,000 feet deep. Study vessel stability Heavy Lift Carrier with atypical breadths capable of carrying these burdens, and in some cases standing out for their bows. 1. Examines possible hulls, their partitioning and ballast for immersion or emersion of the weather deck, more than 10 m deep to take –loading (lifting) - or leave (off- loading). 2. Analyzes the stability of the vessel both immersion / emersion and navigation, with maximum loads with high centers of gravity and stability limit states abacus according to the parameters of the ship. 3. Correction raises the stability of the ship over navigation to prevent excessive accelerations. The results allow, in terms of cargo transport parameters (Zg max) - Weight Load), choosing the most suitable vessel capable of carrying out the immersion, emersion, and navigation, and suggests future research activities.

Face Lift Surgery for Reconstructed Virtual Humans

We introduce an innovative, semi-automatic method to transform low resolution facial meshes into high definition ones, based on the tailoring of a generic, neutral human head model, designed by an artist, to fit the facial features of a specific person. To determine these facial features we need to select a set of "control points" (corners of eyes, lips, etc.) in at least two photographs of the subject's face. The neutral head mesh is then automatically reshaped according to the relation between the control points in the original subject's mesh through a set of transformation pyramids. The last step consists in merging both meshes and filling the gaps that appear in the previous process. This algorithm avoids the use of expensive and complicated technologies to obtain depth maps, which also need to be meshed later.

Lift devices in the flight of Archaeopteryx

Archaeopteryx has played a central role in the debates on the origins of avian (and dinosaurian) flight, even though as a flier it probably represents a relatively late stage in the beginnings of fl ight. We report on aerodynamic tests using a life-sized model of Archaeopteryx performing in a low turbulence wind tunnel. Our results indicate that tail deflection significantly decreased take-off velocity and power consumption, and that the first manual digit could have functioned as the structural precursor of the alula. Such results demonstrate that Archaeopteryx had already evolved high-lift devices, which are functional analogues of those present in today's birds.

Absorption coefficient for the intraband transitions in quantum dot materials

In this paper, we present calculations of the absorption coefficient for transitions between the bound states of quantum dots grown within a semiconductor and the extended states of the conduction band. For completeness, transitions among bound states are also presented. In the separation of variables, single band k·p model is used in which most elements may be expressed analytically. The analytical formulae are collected in the appendix of this paper. It is concluded that the transitions are strong enough to provide a quick path to the conduction band for electrons pumped from the valence to the intermediate band

Combining a Similar Coefficient Identification Algorithm with the Boundary Element Method

The boundary element method (BEM) has been applied successfully to many engineering problems during the last decades. Compared with domain type methods like the finite element method (FEM) or the finite difference method (FDM) the BEM can handle problems where the medium extends to infinity much easier than domain type methods as there is no need to develop special boundary conditions (quiet or absorbing boundaries) or infinite elements at the boundaries introduced to limit the domain studied. The determination of the dynamic stiffness of arbitrarily shaped footings is just one of these fields where the BEM has been the method of choice, especially in the 1980s. With the continuous development of computer technology and the available hardware equipment the size of the problems under study grew and, as the flop count for solving the resulting linear system of equations grows with the third power of the number of equations, there was a need for the development of iterative methods with better performance. In [1] the GMRES algorithm was presented which is now widely used for implementations of the collocation BEM. While the FEM results in sparsely populated coefficient matrices, the BEM leads, in general, to fully or densely populated ones, depending on the number of subregions, posing a serious memory problem even for todays computers. If the geometry of the problem permits the surface of the domain to be meshed with equally shaped elements a lot of the resulting coefficients will be calculated and stored repeatedly. The present paper shows how these unnecessary operations can be avoided reducing the calculation time as well as the storage requirement. To this end a similar coefficient identification algorithm (SCIA), has been developed and implemented in a program written in Fortran 90. The vertical dynamic stiffness of a single pile in layered soil has been chosen to test the performance of the implementation. The results obtained with the 3-d model may be compared with those obtained with an axisymmetric formulation which are considered to be the reference values as the mesh quality is much better. The entire 3D model comprises more than 35000 dofs being a soil region with 21168 dofs the biggest single region. Note that the memory necessary to store all coefficients of this single region is about 6.8 GB, an amount which is usually not available with personal computers. In the problem under study the interface zone between the two adjacent soil regions as well as the surface of the top layer may be meshed with equally sized elements. In this case the application of the SCIA leads to an important reduction in memory requirements. The maximum memory used during the calculation has been reduced to 1.2 GB. The application of the SCIA thus permits problems to be solved on personal computers which otherwise would require much more powerful hardware.

Validation of a CFD wake model based on the actuator disk technique and the thrust coefficient. Preliminary results

A simplified CFD wake model based on the actuator-disk concept is used to simulate the wind turbine, represented by an actuator disk upon which a distribution of forces, defined as axial momentum sources, are applied on the incoming flow. The rotor is supposed to be uniformly loaded, with the exerted forces as a function of the incident wind speed, the thrust coefficient and the rotor diameter. The model is validated through experimental measurements downwind of a wind turbine in terms of wind speed deficit. Validation on turbulence intensity will also be made in the near future.

A 2D computational parametric analysis of the sheltering effect of fences on a railway vehicle standing on a bridge and experiencing crosswinds

In a crosswind scenario, the risk of high-speed trains overturning increases when they run on viaducts since the aerodynamic loads are higher than on the ground. In order to increase safety, vehicles are sheltered by fences that are installed on the viaduct to reduce the loads experienced by the train. Windbreaks can be designed to have different heights, and with or without eaves on the top. In this paper, a parametric study with a total of 12 fence designs was carried out using a two-dimensional model of a train standing on a viaduct. To asses the relative effectiveness of sheltering devices, tests were done in a wind tunnel with a scaled model at a Reynolds number of 1 × 105, and the train’s aerodynamic coefficients were measured. Experimental results were compared with those predicted by Unsteady Reynolds-averaged Navier-Stokes (URANS) simulations of flow, showing that a computational model is able to satisfactorily predict the trend of the aerodynamic coefficients. In a second set of tests, the Reynolds number was increased to 12 × 106 (at a free flow air velocity of 30 m/s) in order to simulate strong wind conditions. The aerodynamic coefficients showed a similar trend for both Reynolds numbers; however, their numerical value changed enough to indicate that simulations at the lower Reynolds number do not provide all required information. Furthermore, the variation of coefficients in the simulations allowed an explanation of how fences modified the flow around the vehicle to be proposed. This made it clear why increasing fence height reduced all the coefficients but adding an eave had an effect mainly on the lift force coefficient. Finally, by analysing the time signals it was possible to clarify the influence of the Reynolds number on the peak-to-peak amplitude, the time period and the Strouhal number.

Gini coefficient, dissimilarity index and Lorenz curve for the spanish port system by type of goods

This paper shows the Gini Coefficient, the dissimilarity Index and the Lorenz Curve for the Spanish Port System by type of goods from 1960 to the year 2010 for business units: Total traffic, Liquid bulk cargo, Solid bulk cargo, General Merchandise and Container (TEUs) with the aim of carcaterizar the Spanish port systems in these periods and propose future strategies.

On ergodic least-squares estimators of the generalized diffusion coefficient for fractional Brownian motion

We analyse a class of estimators of the generalized diffusion coefficient for fractional Brownian motion Bt of known Hurst index H, based on weighted functionals of the single time square displacement. We show that for a certain choice of the weight function these functionals possess an ergodic property and thus provide the true, ensemble-averaged, generalized diffusion coefficient to any necessary precision from a single trajectory data, but at expense of a progressively higher experimental resolution. Convergence is fastest around H ? 0.30, a value in the subdiffusive regime.

Análisis de la influencia del borde de salida abierto en perfiles aerodinámicos a bajos números de Reynolds

El objetivo del presente trabajo es analizar la influencia que tiene sobre el comportamiento aerodinámico del perfil el hecho de que este presente un borde de salida más grueso que el perfil original del que se partía. Este estudio se ha centrado fundamentalmente en la influencia sobre su sustentación aerodinámica, resistencia aerodinámica y, especialmente, sobre la eficiencia aerodinámica del perfil, es decir sobre la relación entre la sustentación y la resistencia aerodinámica. También se ha analizado su influencia en otros aspectos aerodinámicos de los perfiles, como la entrada en pérdida, el ángulo de ataque de sustentación máxima, el ángulo de ataque de eficiencia máxima, el coeficiente de momento aerodinámico y la posición del centro aerodinámico. Estas imperfecciones en el borde de salida pueden aparecer en algunos procesos de fabricación de determinados elementos aerodinámicos, como alas de aviones no tripulados o palas de aeroturbina. Este fenómeno no ha sido analizado en profundidad en la literatura científica, aunque si que se ha analizado por varios autores la influencia sobre el perfil con el borde de salida truncado, o perfiles con la parte final regruesada, utilizados en otras aplicaciones. Para la realización de este estudio se han analizado perfiles de distinto tipo, laminares y no laminares, perfiles simétricos y con curvatura, así como perfiles con distinto espesor, a fin de comparar el grado de influencia del fenómeno estudiado sobre cada tipo de perfil para comparar su grado de sensibilidad a dicha anomalía geométrica. El estudio se ha realizado experimentalmente utilizando una cámara de ensayos diseñada específicamente a tal efecto, así como una balanza electrónica para medir las fuerzas y los momentos sobre el perfil, y un escáner de presiones para medir la distribución de presiones en determinados casos. También se ha abordado el estudio del comportamiento de perfiles con borde de salida más grueso que el nominal pero redondeado en vez de romo, con el objeto de analizar la eficacia de redondear el borde de salida, que es uno de los métodos que se puede utilizar para mitigar este efecto. Por otro lado, como el comportamiento de los perfiles aerodinámicos tiene una fuerte dependencia del número de Reynolds, el estudio se ha centrado en el análisis del comportamiento a bajos números de Reynolds debido a su uso reciente en una amplia gama de aplicaciones, desde vehículos aéreos no tripulados (UAV) hasta palas de aeroturbinas de baja potencia, e incluso debido a su uso potencial en aeronaves diseñadas para volar en atmósferas de baja densidad como la que existe en Marte. El interés de este estudio está orientado al establecimiento de criterios para cuantificar la influencia que tiene el hecho de que el borde de salida sea más grueso que el nominal en la degradación de su eficiencia aerodinámica máxima, con el objeto de poder establecer los límites de aceptación o rechazo de estas piezas una vez fabricadas, según el tipo de perfil aerodinámico utilizado. Del resultado del análisis de los casos estudiados se puede concluir que según aumenta el espesor del borde de salida, dentro del intervalo de estudio, la sustentación aerodinámica aumenta, así como la sustentación máxima, pero aumenta en mayor proporción la resistencia aerodinámica, por lo que se produce una reducción de la eficiencia aerodinámica, en particular de su valor máximo. Por otro lado, el hecho de redondear el borde de salida del perfil ayuda ligeramente a reducir este efecto. ABSTRACT The aim of this thesis is to analyze the effects of airfoil trailing edges thickness when this is thicker than the airfoil nominal. Several factors may lead to an airfoil trailing edge being thicker than the nominal airfoil, and this may affect various aerodynamic parameters. This study has focus on its influence on the airfoil’s aerodynamic lift, drag and, particularly on the aerodynamic efficiency of the airfoil, that is, the relationship between the aerodynamic lift and drag. It has also been studied how this fact may alter some other aerodynamic aspects of airfoils, such as stall, angle of attack of maximum lift, angle of maximum efficiency, aerodynamic moment coefficient and aerodynamic center position. These imperfections in the trailing edge may appear in some manufacturing processes of certain aerodynamic elements, such as unmanned aircraft wings or wind turbine blades. This phenomenon has not been deeply analyzed in the literature, although several authors have discussed its influence on airfoil with truncated trailing edge, or airfoils with thickened end, used in other applications. Various types of airfoils have been analyzed, laminar and non-laminar, symmetric and curved airfoils, and airfoils with different thickness, in order to compare the degree of influence of the phenomenon studied on each airfoil type and thus, to estimate the degree of sensitivity to the anomaly geometry. The study was carried out experimentally using a test chamber designed specifically for this purpose, as well as an electronic balance to measure the forces and moments on the airfoil, and a pressure scanner to measure distribution of pressures in certain cases. It has also been investigated the behavior of airfoils with trailing edge thicker than the nominal, but rounded instead of blunt, in order to analyze the effectiveness of the trailing edge rounding, which is one of the methods that can be used to mitigate this phenomenon. Moreover, as the behavior of the airfoil is highly dependent on the Reynolds number, the study has been focused on the analysis of the behavior at low Reynolds numbers due to recent use of low Reynolds numbers airfoils in a wide range of applications, from unmanned aerial vehicles (UAV) to low power wind turbine blades, or even due to their potential use in aircraft designed to fly in low density atmospheres as the one existing in Mars. The main purpose of this research is to establish a set of criteria for quantifying the influence that a thicker-than–nominal-trailing edge has in the degradation of maximum aerodynamic efficiency, aiming at establishing the acceptance limits for these pieces when they are manufactured, according to the type of airfoil used. Based on the results obtained from the analysis of the cases under study it can be concluded that increasing the thickness of the trailing edge, within the range of study, increases aerodynamic lift, as well as maximum lift, but the aerodynamic drag increases in a higher proportion, and consequently there is a reduction of aerodynamic efficiency, particularly, of its maximum value. On the other hand, rounding the trailing edge of the airfoil slightly helps to reduce this effect.

Análisis de la influencia de imperfecciones en el borde de ataque en perfiles aerodinámicos a bajos números de Reynolds

En esta tesis se ha analizado la influencia que tienen ciertas imperfecciones en el borde de ataque de un perfil aerodinámico sobre el comportamiento aerodinámico general del mismo, centrándose fundamentalmente en la influencia sobre el coeficiente de sustentación máxima, coeficiente de resistencia y sobre la eficiencia aerodinámica del perfil, es decir sobre la relación entre la sustentación y la resistencia aerodinámicas. También se ha analizado su influencia en otros aspectos, como la entrada en pérdida, ángulo de ataque de sustentación máxima, ángulo de ataque de eficiencia máxima, coeficiente de momento aerodinámico y posición del centro aerodinámico. Estos defectos de forma en el borde de ataque pueden aparecer en algunos procesos de fabricación de determinados elementos aerodinámicos, como pueden ser las alas de pequeños aviones no tripulados o las palas de aeroturbina. Los perfiles se ha estudiado a bajos números de Reynolds debido a su uso reciente en una amplia gama de aplicaciones, desde vehículos aéreos no tripulados (UAV) hasta palas de aeroturbina de baja potencia, e incluso debido a su potencial utilización en aeronaves diseñadas para volar en atmósferas de baja densidad. El objeto de estudio de esta tesis no ha sido analizado en profundidad en la literatura científica, aunque sí que se ha estudiado por varios autores el comportamiento de perfiles a bajos números de Reynolds, con ciertas protuberancias sobre su superficie o también con formación de hielo en el borde de ataque. Para la realización de este estudio se han analizado perfiles de distinto tipo, perfiles simétricos y con curvatura, perfiles laminares, y todos ellos con igual o distinto espesor, con el objeto de obtener y comparar la influencia del fenómeno estudiado sobre cada tipo de perfil y así analizar su grado de sensibilidad a estas imperfecciones en la geometría del borde de ataque. Este trabajo ha sido realizado experimentalmente utilizando una túnel aerodinámico diseñado específicamente a tal efecto, así como una balanza electrónica para medir las fuerzas y los momentos sobre el perfil, y un escáner de presiones para medir la distribución de presiones sobre la superficie de los perfiles en determinados casos de interés. La finalidad de este estudio está orientada al establecimiento de criterios para cuantificar la influencia en la aerodinámica del perfil que tiene el hecho de que el borde de ataque presente una discontinuidad geométrica, con el objeto de poder establecer los límites de aceptación o rechazo de estas piezas en el momento de ser fabricadas. Del análisis de los casos estudiados se puede concluir que según aumenta el tamaño de la imperfección del borde de ataque, la sustentación aerodinámica máxima en general disminuye, al igual que la eficiencia aerodinámica máxima, pues la resistencia aerodinámica aumenta. Sin embargo, en algunos casos, para pequeños defectos se produce un efecto contrario. La sustentación máxima aumenta apreciablemente sin apenas pérdida de eficiencia aerodinámica máxima. ABSTRACT The aim of this thesis is to analyze the effects of leading edge imperfections on the aerodynamic characteristics of airfoils at low Reynolds numbers. The leading edge imperfection here considered being a slight displacement of half airfoil with respect to the other. This study has focus on its influence on the airfoil’s aerodynamic lift, drag and on the aerodynamic efficiency of the airfoil, that is, the relationship between the aerodynamic lift and drag. It has also been studied how this fact may alter some other aerodynamic aspects of airfoils, such as stall, angle of attack of maximum lift, angle of maximum efficiency, aerodynamic moment coefficient and aerodynamic center position. These imperfections in the leading edge may appear in some manufacturing processes of certain aerodynamic elements, such as unmanned aircraft wings or wind turbine blades. The study has focused on the analysis of the behavior at low Reynolds numbers due to recent use of low Reynolds numbers airfoils in a wide range of applications, from unmanned aerial vehicles (UAV) to low power wind turbine blades, or even due to their potential use in aircraft designed to fly in low density atmospheres as the one existing in Mars. This phenomenon has not been deeply analyzed in the literature, although several authors have discussed on airfoils at low Reynolds number, with leading edge protuberances or airfoils with ice accretions. Various types of airfoils have been analyzed, laminar and non-laminar, symmetric and curved airfoils, and airfoils with different thickness, in order to compare the degree of influence of the phenomenon studied on each airfoil type and thus, to estimate the degree of sensitivity to the anomaly geometry. The study was carried out experimentally using a test chamber designed specifically for this purpose, as well as an electronic balance to measure the forces and moments on the airfoil, and a pressure scanner to measure distribution of pressures in certain cases. The main purpose of this research is to establish a criteria for quantifying the influence that a slight displacement of half aerofoil with respect to the other has in the degradation of aerodynamics characteristics, aiming at establishing the acceptance limits for these pieces when they are manufactured, according to the type of airfoil used. Based on the results obtained from the analysis of the cases under study it can be concluded that displacements, within the range of study, decreases maximum aerodynamic lift, but the aerodynamic drag increases, and consequently there is a reduction of aerodynamic efficiency. However, in some cases, for small defects opposite effect occurs. The maximum lift increases significantly with little loss of maximum aerodynamic efficiency.