Optimization of the irrigation time and irrigation frequency by using Hydrus-2D and a capacitance FDR sensor

The evolution of water content on a sandy soil during the sprinkler irrigation campaign, in the summer of 2010, of a field of sugar beet crop located at Valladolid (Spain) is assessed by a capacitive FDR (Frequency Domain Reflectometry) EnviroScan. This field is one of the experimental sites of the Spanish research center for the sugar beet development (AIMCRA). The objective of the work focus on monitoring the soil water content evolution of consecutive irrigations during the second two weeks of July (from the 12th to the 28th). These measurements will be used to simulate water movement by means of Hydrus-2D. The water probe logged water content readings (m3/m3) at 10, 20, 40 and 60 cm depth every 30 minutes. The probe was placed between two rows in one of the typical 12 x 15 m sprinkler irrigation framework. Furthermore, a texture analysis at the soil profile was also conducted. The irrigation frequency in this farm was set by the own personal farmer 0 s criteria that aiming to minimizing electricity pumping costs, used to irrigate at night and during the weekend i.e. longer irrigation frequency than expected. However, the high evapotranspiration rates and the weekly sugar beet water consumption—up to 50mm/week—clearly determined the need for lower this frequency. Moreover, farmer used to irrigate for six or five hours whilst results from the EnviroScan probe showed the soil profile reaching saturation point after the first three hours. It must be noted that AIMCRA provides to his members with a SMS service regarding weekly sugar beet water requirement; from the use of different meteorological stations and evapotranspiration pans, farmers have an idea of the weekly irrigation needs. Nevertheless, it is the farmer 0 s decision to decide how to irrigate. Thus, in order to minimize water stress and pumping costs, a suitable irrigation time and irrigation frequency was modeled with Hydrus-2D. Results for the period above mentioned showed values of water content ranging from 35 and 30 (m3/m3) for the first 10 and 20cm profile depth (two hours after irrigation) to the minimum 14 and 13 (m3/m3) ( two hours before irrigation). For the 40 and 60 cm profile depth, water content moves steadily across the dates: The greater the root activity the greater the water content variation. According to the results in the EnviroScan probe and the modeling in Hydrus-2D, shorter frequencies and irrigation times are suggested.

Advances in the Simultaneous Multiple Surface optical design method for imaging and non-imaging applications

Classical imaging optics has been developed over centuries in many areas, such as its paraxial imaging theory and practical design methods like multi-parametric optimization techniques. Although these imaging optical design methods can provide elegant solutions to many traditional optical problems, there are more and more new design problems, like solar concentrator, illumination system, ultra-compact camera, etc., that require maximum energy transfer efficiency, or ultra-compact optical structure. These problems do not have simple solutions from classical imaging design methods, because not only paraxial rays, but also non-paraxial rays should be well considered in the design process. Non-imaging optics is a newly developed optical discipline, which does not aim to form images, but to maximize energy transfer efficiency. One important concept developed from non-imaging optics is the “edge-ray principle”, which states that the energy flow contained in a bundle of rays will be transferred to the target, if all its edge rays are transferred to the target. Based on that concept, many CPC solar concentrators have been developed with efficiency close to the thermodynamic limit. When more than one bundle of edge-rays needs to be considered in the design, one way to obtain solutions is to use SMS method. SMS stands for Simultaneous Multiple Surface, which means several optical surfaces are constructed simultaneously. The SMS method was developed as a design method in Non-imaging optics during the 90s. The method can be considered as an extension to the Cartesian Oval calculation. In the traditional Cartesian Oval calculation, one optical surface is built to transform an input wave-front to an out-put wave-front. The SMS method however, is dedicated to solve more than 1 wave-fronts transformation problem. In the beginning, only 2 input wave-fronts and 2 output wave-fronts transformation problem was considered in the SMS design process for rotational optical systems or free-form optical systems. Usually “SMS 2D” method stands for the SMS procedure developed for rotational optical system, and “SMS 3D” method for the procedure for free-form optical system. Although the SMS method was originally employed in non-imaging optical system designs, it has been found during this thesis that with the improved capability to design more surfaces and control more input and output wave-fronts, the SMS method can also be applied to imaging system designs and possesses great advantage over traditional design methods. In this thesis, one of the main goals to achieve is to further develop the existing SMS-2D method to design with more surfaces and improve the stability of the SMS-2D and SMS-3D algorithms, so that further optimization process can be combined with SMS algorithms. The benefits of SMS plus optimization strategy over traditional optimization strategy will be explained in details for both rotational and free-form imaging optical system designs. Another main goal is to develop novel design concepts and methods suitable for challenging non-imaging applications, e.g. solar concentrator and solar tracker. This thesis comprises 9 chapters and can be grouped into two parts: the first part (chapter 2-5) contains research works in the imaging field, and the second part (chapter 6-8) contains works in the non-imaging field. In the first chapter, an introduction to basic imaging and non-imaging design concepts and theories is given. Chapter 2 presents a basic SMS-2D imaging design procedure using meridian rays. In this chapter, we will set the imaging design problem from the SMS point of view, and try to solve the problem numerically. The stability of this SMS-2D design procedure will also be discussed. The design concepts and procedures developed in this chapter lay the path for further improvement. Chapter 3 presents two improved SMS 3 surfaces’ design procedures using meridian rays (SMS-3M) and skew rays (SMS-1M2S) respectively. The major improvement has been made to the central segments selections, so that the whole SMS procedures become more stable compared to procedures described in Chapter 2. Since these two algorithms represent two types of phase space sampling, their image forming capabilities are compared in a simple objective design. Chapter 4 deals with an ultra-compact SWIR camera design with the SMS-3M method. The difficulties in this wide band camera design is how to maintain high image quality meanwhile reduce the overall system length. This interesting camera design provides a playground for the classical design method and SMS design methods. We will show designs and optical performance from both classical design method and the SMS design method. Tolerance study is also given as the end of the chapter. Chapter 5 develops a two-stage SMS-3D based optimization strategy for a 2 freeform mirrors imaging system. In the first optimization phase, the SMS-3D method is integrated into the optimization process to construct the two mirrors in an accurate way, drastically reducing the unknown parameters to only few system configuration parameters. In the second optimization phase, previous optimized mirrors are parameterized into Qbfs type polynomials and set up in code V. Code V optimization results demonstrates the effectiveness of this design strategy in this 2-mirror system design. Chapter 6 shows an etendue-squeezing condenser optics, which were prepared for the 2010 IODC illumination contest. This interesting design employs many non-imaging techniques such as the SMS method, etendue-squeezing tessellation, and groove surface design. This device has theoretical efficiency limit as high as 91.9%. Chapter 7 presents a freeform mirror-type solar concentrator with uniform irradiance on the solar cell. Traditional parabolic mirror concentrator has many drawbacks like hot-pot irradiance on the center of the cell, insufficient use of active cell area due to its rotational irradiance pattern and small acceptance angle. In order to conquer these limitations, a novel irradiance homogenization concept is developed, which lead to a free-form mirror design. Simulation results show that the free-form mirror reflector has rectangular irradiance pattern, uniform irradiance distribution and large acceptance angle, which confirm the viability of the design concept. Chapter 8 presents a novel beam-steering array optics design strategy. The goal of the design is to track large angle parallel rays by only moving optical arrays laterally, and convert it to small angle parallel output rays. The design concept is developed as an extended SMS method. Potential applications of this beam-steering device are: skylights to provide steerable natural illumination, building integrated CPV systems, and steerable LED illumination. Conclusion and future lines of work are given in Chapter 9. Resumen La óptica de formación de imagen clásica se ha ido desarrollando durante siglos, dando lugar tanto a la teoría de óptica paraxial y los métodos de diseño prácticos como a técnicas de optimización multiparamétricas. Aunque estos métodos de diseño óptico para formación de imagen puede aportar soluciones elegantes a muchos problemas convencionales, siguen apareciendo nuevos problemas de diseño óptico, concentradores solares, sistemas de iluminación, cámaras ultracompactas, etc. que requieren máxima transferencia de energía o dimensiones ultracompactas. Este tipo de problemas no se pueden resolver fácilmente con métodos clásicos de diseño porque durante el proceso de diseño no solamente se deben considerar los rayos paraxiales sino también los rayos no paraxiales. La óptica anidólica o no formadora de imagen es una disciplina que ha evolucionado en gran medida recientemente. Su objetivo no es formar imagen, es maximazar la eficiencia de transferencia de energía. Un concepto importante de la óptica anidólica son los “rayos marginales”, que se pueden utilizar para el diseño de sistemas ya que si todos los rayos marginales llegan a nuestra área del receptor, todos los rayos interiores también llegarán al receptor. Haciendo uso de este principio, se han diseñado muchos concentradores solares que funcionan cerca del límite teórico que marca la termodinámica. Cuando consideramos más de un haz de rayos marginales en nuestro diseño, una posible solución es usar el método SMS (Simultaneous Multiple Surface), el cuál diseña simultáneamente varias superficies ópticas. El SMS nació como un método de diseño para óptica anidólica durante los años 90. El método puede ser considerado como una extensión del cálculo del óvalo cartesiano. En el método del óvalo cartesiano convencional, se calcula una superficie para transformar un frente de onda entrante a otro frente de onda saliente. El método SMS permite transformar varios frentes de onda de entrada en frentes de onda de salida. Inicialmente, sólo era posible transformar dos frentes de onda con dos superficies con simetría de rotación y sin simetría de rotación, pero esta limitación ha sido superada recientemente. Nos referimos a “SMS 2D” como el método orientado a construir superficies con simetría de rotación y llamamos “SMS 3D” al método para construir superficies sin simetría de rotación o free-form. Aunque el método originalmente fue aplicado en el diseño de sistemas anidólicos, se ha observado que gracias a su capacidad para diseñar más superficies y controlar más frentes de onda de entrada y de salida, el SMS también es posible aplicarlo a sistemas de formación de imagen proporcionando una gran ventaja sobre los métodos de diseño tradicionales. Uno de los principales objetivos de la presente tesis es extender el método SMS-2D para permitir el diseño de sistemas con mayor número de superficies y mejorar la estabilidad de los algoritmos del SMS-2D y SMS-3D, haciendo posible combinar la optimización con los algoritmos. Los beneficios de combinar SMS y optimización comparado con el proceso de optimización tradicional se explican en detalle para sistemas con simetría de rotación y sin simetría de rotación. Otro objetivo importante de la tesis es el desarrollo de nuevos conceptos de diseño y nuevos métodos en el área de la concentración solar fotovoltaica. La tesis está estructurada en 9 capítulos que están agrupados en dos partes: la primera de ellas (capítulos 2-5) se centra en la óptica formadora de imagen mientras que en la segunda parte (capítulos 6-8) se presenta el trabajo del área de la óptica anidólica. El primer capítulo consta de una breve introducción de los conceptos básicos de la óptica anidólica y la óptica en formación de imagen. El capítulo 2 describe un proceso de diseño SMS-2D sencillo basado en los rayos meridianos. En este capítulo se presenta el problema de diseñar un sistema formador de imagen desde el punto de vista del SMS y se intenta obtener una solución de manera numérica. La estabilidad de este proceso se analiza con detalle. Los conceptos de diseño y los algoritmos desarrollados en este capítulo sientan la base sobre la cual se realizarán mejoras. El capítulo 3 presenta dos procedimientos para el diseño de un sistema con 3 superficies SMS, el primero basado en rayos meridianos (SMS-3M) y el segundo basado en rayos oblicuos (SMS-1M2S). La mejora más destacable recae en la selección de los segmentos centrales, que hacen más estable todo el proceso de diseño comparado con el presentado en el capítulo 2. Estos dos algoritmos representan dos tipos de muestreo del espacio de fases, su capacidad para formar imagen se compara diseñando un objetivo simple con cada uno de ellos. En el capítulo 4 se presenta un diseño ultra-compacto de una cámara SWIR diseñada usando el método SMS-3M. La dificultad del diseño de esta cámara de espectro ancho radica en mantener una alta calidad de imagen y al mismo tiempo reducir drásticamente sus dimensiones. Esta cámara es muy interesante para comparar el método de diseño clásico y el método de SMS. En este capítulo se presentan ambos diseños y se analizan sus características ópticas. En el capítulo 5 se describe la estrategia de optimización basada en el método SMS-3D. El método SMS-3D calcula las superficies ópticas de manera precisa, dejando sólo unos pocos parámetros libres para decidir la configuración del sistema. Modificando el valor de estos parámetros se genera cada vez mediante SMS-3D un sistema completo diferente. La optimización se lleva a cabo variando los mencionados parámetros y analizando el sistema generado. Los resultados muestran que esta estrategia de diseño es muy eficaz y eficiente para un sistema formado por dos espejos. En el capítulo 6 se describe un sistema de compresión de la Etendue, que fue presentado en el concurso de iluminación del IODC en 2010. Este interesante diseño hace uso de técnicas propias de la óptica anidólica, como el método SMS, el teselado de las lentes y el diseño mediante grooves. Este dispositivo tiene un límite teórica en la eficiencia del 91.9%. El capítulo 7 presenta un concentrador solar basado en un espejo free-form con irradiancia uniforme sobre la célula. Los concentradores parabólicos tienen numerosas desventajas como los puntos calientes en la zona central de la célula, uso no eficiente del área de la célula al ser ésta cuadrada y además tienen ángulos de aceptancia de reducido. Para poder superar estas limitaciones se propone un novedoso concepto de homogeneización de la irrandancia que se materializa en un diseño con espejo free-form. El análisis mediante simulación demuestra que la irradiancia es homogénea en una región rectangular y con mayor ángulo de aceptancia, lo que confirma la viabilidad del concepto de diseño. En el capítulo 8 se presenta un novedoso concepto para el diseño de sistemas afocales dinámicos. El objetivo del diseño es realizar un sistema cuyo haz de rayos de entrada pueda llegar con ángulos entre ±45º mientras que el haz de rayos a la salida sea siempre perpendicular al sistema, variando únicamente la posición de los elementos ópticos lateralmente. Las aplicaciones potenciales de este dispositivo son varias: tragaluces que proporcionan iluminación natural, sistemas de concentración fotovoltaica integrados en los edificios o iluminación direccionable con LEDs. Finalmente, el último capítulo contiene las conclusiones y las líneas de investigación futura.

Response threshold models, stochastic learning automata and ant colony optimization-based decentralized self-coordination algorithms for heterogeneous multi-tasks distribution in multi-robot systems

In recent decades, there has been an increasing interest in systems comprised of several autonomous mobile robots, and as a result, there has been a substantial amount of development in the eld of Articial Intelligence, especially in Robotics. There are several studies in the literature by some researchers from the scientic community that focus on the creation of intelligent machines and devices capable to imitate the functions and movements of living beings. Multi-Robot Systems (MRS) can often deal with tasks that are dicult, if not impossible, to be accomplished by a single robot. In the context of MRS, one of the main challenges is the need to control, coordinate and synchronize the operation of multiple robots to perform a specic task. This requires the development of new strategies and methods which allow us to obtain the desired system behavior in a formal and concise way. This PhD thesis aims to study the coordination of multi-robot systems, in particular, addresses the problem of the distribution of heterogeneous multi-tasks. The main interest in these systems is to understand how from simple rules inspired by the division of labor in social insects, a group of robots can perform tasks in an organized and coordinated way. We are mainly interested on truly distributed or decentralized solutions in which the robots themselves, autonomously and in an individual manner, select a particular task so that all tasks are optimally distributed. In general, to perform the multi-tasks distribution among a team of robots, they have to synchronize their actions and exchange information. Under this approach we can speak of multi-tasks selection instead of multi-tasks assignment, which means, that the agents or robots select the tasks instead of being assigned a task by a central controller. The key element in these algorithms is the estimation ix of the stimuli and the adaptive update of the thresholds. This means that each robot performs this estimate locally depending on the load or the number of pending tasks to be performed. In addition, it is very interesting the evaluation of the results in function in each approach, comparing the results obtained by the introducing noise in the number of pending loads, with the purpose of simulate the robot's error in estimating the real number of pending tasks. The main contribution of this thesis can be found in the approach based on self-organization and division of labor in social insects. An experimental scenario for the coordination problem among multiple robots, the robustness of the approaches and the generation of dynamic tasks have been presented and discussed. The particular issues studied are: Threshold models: It presents the experiments conducted to test the response threshold model with the objective to analyze the system performance index, for the problem of the distribution of heterogeneous multitasks in multi-robot systems; also has been introduced additive noise in the number of pending loads and has been generated dynamic tasks over time. Learning automata methods: It describes the experiments to test the learning automata-based probabilistic algorithms. The approach was tested to evaluate the system performance index with additive noise and with dynamic tasks generation for the same problem of the distribution of heterogeneous multi-tasks in multi-robot systems. Ant colony optimization: The goal of the experiments presented is to test the ant colony optimization-based deterministic algorithms, to achieve the distribution of heterogeneous multi-tasks in multi-robot systems. In the experiments performed, the system performance index is evaluated by introducing additive noise and dynamic tasks generation over time.

Regularized model learning in EDAs for continuous and multi-objective optimization

Probabilistic modeling is the de�ning characteristic of estimation of distribution algorithms (EDAs) which determines their behavior and performance in optimization. Regularization is a well-known statistical technique used for obtaining an improved model by reducing the generalization error of estimation, especially in high-dimensional problems. `1-regularization is a type of this technique with the appealing variable selection property which results in sparse model estimations. In this thesis, we study the use of regularization techniques for model learning in EDAs. Several methods for regularized model estimation in continuous domains based on a Gaussian distribution assumption are presented, and analyzed from di�erent aspects when used for optimization in a high-dimensional setting, where the population size of EDA has a logarithmic scale with respect to the number of variables. The optimization results obtained for a number of continuous problems with an increasing number of variables show that the proposed EDA based on regularized model estimation performs a more robust optimization, and is able to achieve signi�cantly better results for larger dimensions than other Gaussian-based EDAs. We also propose a method for learning a marginally factorized Gaussian Markov random �eld model using regularization techniques and a clustering algorithm. The experimental results show notable optimization performance on continuous additively decomposable problems when using this model estimation method. Our study also covers multi-objective optimization and we propose joint probabilistic modeling of variables and objectives in EDAs based on Bayesian networks, speci�cally models inspired from multi-dimensional Bayesian network classi�ers. It is shown that with this approach to modeling, two new types of relationships are encoded in the estimated models in addition to the variable relationships captured in other EDAs: objectivevariable and objective-objective relationships. An extensive experimental study shows the e�ectiveness of this approach for multi- and many-objective optimization. With the proposed joint variable-objective modeling, in addition to the Pareto set approximation, the algorithm is also able to obtain an estimation of the multi-objective problem structure. Finally, the study of multi-objective optimization based on joint probabilistic modeling is extended to noisy domains, where the noise in objective values is represented by intervals. A new version of the Pareto dominance relation for ordering the solutions in these problems, namely �-degree Pareto dominance, is introduced and its properties are analyzed. We show that the ranking methods based on this dominance relation can result in competitive performance of EDAs with respect to the quality of the approximated Pareto sets. This dominance relation is then used together with a method for joint probabilistic modeling based on `1-regularization for multi-objective feature subset selection in classi�cation, where six di�erent measures of accuracy are considered as objectives with interval values. The individual assessment of the proposed joint probabilistic modeling and solution ranking methods on datasets with small-medium dimensionality, when using two di�erent Bayesian classi�ers, shows that comparable or better Pareto sets of feature subsets are approximated in comparison to standard methods.

In-situ optical reflectance characterization of ion beam irradiation damage on crystalline (quartz) and amorphous (silica) SiO2

Outline: • Motivation, aim • Complement waveguide data on silica • Optical data in quartz • Detailed analysis, i.e. both fluence kinetics and resolution • Efficiency of irradiation and analysis, samples, time... • Experimental set-up description • Reflectance procedure • Options: light source (lasers, white light..), detectors, configurations • Results and discussion • Comparative of amorphous and crystalline phases

Two-photon photocurrent and voltage up-conversion in a quantum dot intermediate band solar cell

It has been proposed that the use of self-assembled quantum dot (QD) arrays can break the Shockley-Queisser efficiency limit by extending the absorption of solar cells into the low-energy photon range while preserving their output voltage. This would be possible if the infrared photons are absorbed in the two sub-bandgap QD transitions simultaneously and the energy of two photons is added up to produce one single electron-hole pair, as described by the intermediate band model. Here, we present an InAs/Al 0.25Ga 0.75As QD solar cell that exhibits such electrical up-conversion of low-energy photons. When the device is monochromatically illuminated with 1.32 eV photons, open-circuit voltages as high as 1.58 V are measured (for a total gap of 1.8 eV). Moreover, the photocurrent produced by illumination with photons exciting the valence band to intermediate band (VB-IB) and the intermediate band to conduction band (IB-CB) transitions can be both spectrally resolved. The first corresponds to the QD inter-band transition and is observable for photons of energy mayor que 1 eV, and the later corresponds to the QD intra-band transition and peaks around 0.5 eV. The voltage up-conversion process reported here for the first time is the key to the use of the low-energy end of the solar spectrum to increase the conversion efficiency, and not only the photocurrent, of single-junction photovoltaic devices. In spite of the low absorption threshold measured in our devices - 0.25 eV - we report open-circuit voltages at room temperature as high as 1.12 V under concentrated broadband illumination.

Time and space partition platform for safe and secure flight software.

There are a number of research and development activities that are exploring Time and Space Partition (TSP) to implement safe and secure flight software. This approach allows to execute different real-time applications with different levels of criticality in the same computer board. In order to do that, flight applications must be isolated from each other in the temporal and spatial domains. This paper presents the first results of a partitioning platform based on the Open Ravenscar Kernel (ORK+) and the XtratuM hypervisor. ORK+ is a small, reliable real-time kernel supporting the Ada Ravenscar Computational model that is central to the ASSERT development process. XtratuM supports multiple virtual machines, i.e. partitions, on a single computer and is being used in the Integrated Modular Avionics for Space study. ORK+ executes in an XtratuM partition enabling Ada applications to share the computer board with other applications.

Adaptación de un reproductor de contenidos multimedia para la recepción de vídeo escalable sobre un protocolo de tiempo real

En los últimos años, debido al notable desarrollo de los terminales portátiles, que han pasado de ser “simples” teléfonos o reproductores a puros ordenadores, ha crecido el número de servicios que ofrecen cada vez mayor cantidad de contenido multimedia a través de internet. Además, la distinta evolución de estos terminales hace que nos encontremos en el mercado con una amplísima gama de productos de diferentes tamaños y capacidades de procesamiento, lo que hace necesario encontrar una fórmula que permita satisfacer la demanda de dichos servicios sea cual sea la naturaleza de nuestro dispositivo. Para poder ofrecer una solución adecuada se ha optado por la integración de un protocolo como RTP y un estándar de video como SVC. RTP (Real-time Transport Protocol), en contraposición a los protocolos de propósito general fue diseñado para aplicaciones de tiempo real por lo que es ideal para el streaming de contenido multimedia. Por su parte, SVC es un estándar de video escalable que permite transmitir en un mismo stream una capa base y múltiples capas de mejora, por lo que podremos adaptar la calidad y tamaño del contenido a la capacidad y tamaño de nuestro dispositivo. El objetivo de este proyecto consiste en integrar y modificar tanto el reproductor MPlayer como la librería RTP live555 de tal forma que sean capaces de soportar el formato SVC sobre el protocolo RTP y montar un sistema servidorcliente para comprobar su funcionamiento. Aunque este proceso esté orientado a llevarse a cabo en un dispositivo móvil, para este proyecto se ha optado por realizarlo en el escenario más sencillo posible, para lo cual, se emitirán secuencias a una máquina virtual alojada en el mismo ordenador que el servidor. ABSTRACT In recent years, due to the remarkable development of mobile devices, which have evolved from "simple" phones or players to computers, the amount of services that offer multimedia content over the internet have shot up. Furthermore, the different evolution of these terminals causes that we can find in the market a wide range of different sizes and processing capabilities, making necessary to find a formula that will satisfy the demand for such services regardless of the nature of our device. In order to provide a suitable solution we have chosen to integrate a protocol as RTP and a video standard as SVC. RTP (Real-time Transport Protocol), in opposition to general purpose protocols was designed for real-time applications making it ideal for media streaming. Meanwhile, SVC is a scalable video standard which can transmit a single stream in a base layer and multiple enhancement layers, so that we can adapt the quality and size of the content to the capacity and size of our device. The objective of this project is to integrate and modify both MPlayer and RTP library live555 so that they support the SVC format over RTP protocol and set up a client-server system to check its behavior. Although this process has been designed to be done on a mobile device, for this project we have chosen to do it in the simplest possible scenario so we will stream to a virtual machine hosted on the same computer where we have the server.

Time and space partitioning the EagleEye reference mission

We discuss experiences gained by porting a Software Validation Facility (SVF) and a satellite Central Software (CSW) to a platform with support for Time and Space Partitioning (TSP). The SVF and CSW are part of the EagleEye Reference mission of the European Space Agency (ESA). As a reference mission, EagleEye is a perfect candidate to evaluate practical aspects of developing satellite CSW for and on TSP platforms. The specific TSP platform we used consists of a simulate D LEON3 CPU controlled by the XtratuM separation micro-kernel. On top of this, we run five separate partitions. Each partition ru n s its own real-time operating system or Ada run-time kernel, which in turn are running the application software of the CSW. We describe issues related to partitioning; inter-partition communication; scheduling; I/O; and fault-detection, isolation, and recovery (FDIR)

Characterization of tomato Cycling Dof Factors reveals conserved and new functions in the control of flowering time and abiotic stress responses.

DNA binding with One Finger (DOF) transcription factors are involved in multiple aspects of plant growth and development but their precise roles in abiotic stress tolerance are largely unknown. Here we report a group of five tomato DOF genes, homologous to Arabidopsis Cycling DOF Factors (CDFs), that function as transcriptional regulators involved in responses to drought and salt stress and flowering-time control in a gene-specific manner. SlCDF1?5 are nuclear proteins that display specific binding with different affinities to canonical DNA target sequences and present diverse transcriptional activation capacities in vivo. SlCDF1?5 genes exhibited distinct diurnal expression patterns and were differentially induced in response to osmotic, salt, heat, and low-temperature stresses. Arabidopsis plants overexpressing SlCDF1 or SlCDF3 showed increased drought and salt tolerance. In addition, the expression of various stress-responsive genes, such as COR15, RD29A, and RD10, were differentially activated in the overexpressing lines. Interestingly, overexpression in Arabidopsis of SlCDF3 but not SlCDF1 promotes late flowering through modulation of the expression of flowering control genes such as CO and FT. Overall, our data connect SlCDFs to undescribed functions related to abiotic stress tolerance and flowering time through the regulation of specific target genes and an increase in particular metabolites

Identifying Potential Risks and Benefits of Using Cloud in Distributed Software Development.

Cloud-based infrastructure has been increasingly adopted by the industry in distributed software development (DSD) environments. Its proponents claim that its several benefits include reduced cost, increased speed and greater productivity in software development. Empirical evaluations, however, are in the nascent stage of examining both the benefits and the risks of cloud-based infrastructure. The objective of this paper is to identify potential benefits and risks of using cloud in a DSD project conducted by teams based in Helsinki and Madrid. A cross-case qualitative analysis is performed based on focus groups conducted at the Helsinki and Madrid sites. Participants observations are used to supplement the analysis. The results of the analysis indicated that the main benefits of using cloud are rapid development, continuous integration, cost savings, code sharing, and faster ramp-up. The key risks determined by the project are dependencies, unavailability of access to the cloud, code commitment and integration, technical debt, and additional support costs. The results revealed that if such environments are not planned and set up carefully, the benefits of using cloud in DSD projects might be overshadowed by the risks associated with it.

Association of breakfast consumption with objectively measured and self-reported physical activity, sedentary time and physical fitness in European adolescents: the HELENA (Healthy Lifestyle in Europe by Nutrition in Adolescence) Study

Objective: To examine the association of breakfast consumption with objectively measured and self-reported physical activity, sedentary time and physical fitness. Design: The HELENA (Healthy Lifestyle in Europe by Nutrition in Adolescence) Cross-Sectional Study. Breakfast consumption was assessed by two non-consecutive 24 h recalls and by a ‘Food Choices and Preferences’ questionnaire. Physical activity, sedentary time and physical fitness components (cardiorespiratory fitness, muscular fitness and speed/agility) were measured and self-reported. Socio-economic status was assessed by questionnaire. Setting: Ten European cities. Subjects: Adolescents (n 2148; aged 12?5–17?5 years). Results: Breakfast consumption was not associated with measured or self-reported physical activity. However, 24 h recall breakfast consumption was related to measured sedentary time in males and females; although results were not confirmed when using other methods to assess breakfast patterns or sedentary time. Breakfast consumption was not related to muscular fitness and speed/agility in males and females. However, male breakfast consumers had higher cardiorespiratory fitness compared with occasional breakfast consumers and breakfast skippers, while no differences were observed in females. Overall, results were consistent using different methods to assess breakfast consumption or cardiorespiratory fitness (all P#0?005). In addition, both male and female breakfast skippers (assessed by 24 h recall) were less likely to have high measured cardiorespiratory fitness compared with breakfast consumers (OR50?33; 95% CI 0?18, 0?59 and OR50?56; 95 %CI 0?32, 0?98,respectively). Results persisted across methods. Conclusions: Skipping breakfast does not seem to be related to physical activity,sedentary time or muscular fitness and speed/agility as physical fitness components in European adolescents; yet it is associated with both measured and self-reported cardiorespiratory fitness, which extends previous findings.

Design and Multi-Objective Optimization of EMI Input Filters

An EMI filter design procedure for power converters is proposed. Based on a given noise spectrum, information about the converter noise source impedance and design constraints, the design space of the input filter is defined. The design is based on component databases and detailed models of the filter components, including high frequency parasitics, losses, weight, volume, etc.. The design space is mapped onto a performance space in which different filter implementations are evaluated and compared. A multi-objective optimization approach is used to obtain optimal designs w.r.t. a given performance function.

Escuela en Hunstanton de A+P Smithson: el Nuevo Brutalismo en Inglaterra

La tesis estudia en detalle la Hunstanton Secondary School y su trascendencia. Así, se trata de analizar el conjunto de procesos que hace que esta obra sea entendida como el manifiesto construido del Nuevo Brutalismo en Inglaterra. La Escuela en Hunstanton fue la primera obra proyectada y construida por los Smithson y, si se considera que el legado que dejaron Alison y Peter fue más de carácter teórico que constructivo, ésta se ha convertido en un edificio relevante dentro de su trayectoria profesional. Además, el rigor con el que fue realizado el proyecto y la ratificación de las ideas que subyacían tras él, a pesar del extenso intervalo temporal que caracterizó su proceso constructivo, hacen que esta obra se convierta en una síntesis de la filosofía arquitectónica gestada en Inglaterra tras la guerra. Por otro lado, hay que contemplar que la sencillez del lenguaje constructivo empleado, viene dada por la compleja reiteración de los sistemas proyectuales tipo que formulan para este proyecto y el establecimiento de una gramática casi matemática. La sistematización de su vocabulario hace que, tras el análisis de su arquitectura, se encuentren nuevos parámetros capaces de documentar este momento de la historia de la arquitectura en Inglaterra. La envolvente del edificio constituye al tiempo fachada y estructura. Esta característica ha pasado inadvertida cuando, en numerosas ocasiones y durante seis décadas, se han venido publicando las fotografías de la obra terminada y los dibujos que los Smithson habían realizado en la fase de proyecto. Como consecuencia, ha proliferado el conocimiento de la arquitectura de la escuela a un nivel más superficial, mostrando el resultado formal de la misma y con ello, simplemente se ha dejado intuir la gran influencia que Mies Van der Rohe provocó en los Smithson en los primeros años de desarrollo de su labor como arquitectos. El objetivo principal de esta tesis es, por tanto, facilitar el entendimiento del espacio que propusieron los Smithson a partir del análisis pormenorizado de los distintos sistemas constructivos empleados y del equipo personal que se vio implicado en su construcción. Para ello, es necesario abordar el estudio de los materiales y mecanismos proyectuales que hicieron posible que este conjunto de espacios –interiores y exteriores- resultase definido a través de la relación entre dos variables: una evidente austeridad en la utilización de los materiales y la combinación de los distintos sistemas intervinientes a partir del recurso de la repetición. La Escuela de Hunstanton, a pesar de las inoportunas intervenciones realizadas para adaptar el centro a unas necesidades derivadas de su número de alumnos actual (el doble que en su inicio), continúa proclamando su integridad espacial. Partiendo de la hipótesis de que la arquitectura de la Secondary School en Hunstanton, representa el manifiesto construido del Nuevo Brutalismo en Inglaterra, se concluye que el resultado de su construcción fue consecuencia de numerosas influencias que, en relación con los Smithson, estuvieron presentes durante los años en que se gestó. Algo que va más allá de la conclusión de aquellos debates arquitectónicos que se habían emprendido, por escrito, en las distintas revistas locales de arquitectura. Los mecanismos compositivos empleados, también habían tenido mucho que ver con lo que los historiadores del arte habían venido aportando a la historia de la arquitectura hasta ese momento. Desde los años 40, éstos últimos habían emprendido una nueva manera de contar la historia en la que quedaba fuertemente involucrada su capacidad crítica, provocando interferencias en la mentalidad de los arquitectos de nueva generación y otorgándoles un bagaje cultural subliminalmente determinado y subjetivo. Por supuesto, en el resultado arquitectónico final, también tuvieron mucho que ver los recursos materiales de que se disponía en aquel momento. Así como la optimización de los mismos a través de la adopción de nuevas metodologías de trabajo como puede ser la organización multidisciplinar. La inclusión del ingeniero Ronald Jenkins en el equipo de trabajo de los Smithson supuso una gran oportunidad. Este ingeniero, propuso poner en práctica la entonces innovadora Teoría Plástica en la metodología de cálculo estructural y, con ello consiguió enriquecer el resultado espacial, posibilitando la percepción de una arquitectura ligera –a pesar de sus grandes dimensiones- y vinculada al paisaje donde se inserta. Pero todos estos condicionantes fueron pasados a su vez por el filtro del deseo de una regeneración social, que buscaba el modelo de la sociedad americana. El Buen Vivir que propugnaban los americanos, viajaba a Europa de la mano de la publicidad. Y, al igual que la componente publicitaria tuvo algo que ver en el proceso creativo de la arquitectura de la escuela, también lo tuvo el conocimiento del arte pop y sus recursos compositivos. ABSTRACT The thesis examines in detail the project of Hunstanton Secondary School and the architectural language’s significance used in it. Thus, it is reinterpreting the set of processes that makes this work to be understood as the “built manifesto” of the English New Brutalism. Hunstanton School’s project was the first work designed and built by the Smithsons and, considering their legacy -more theoretical than constructed-, make of this building an important work within their career. In addition, the rigor with which it was carried out the project and the ratification of the ideas lying behind him, make this work becomes a synthesis of the architectural philosophy gestated in England after the war, despite the extensive time interval that characterized its construction process. On the other hand, it must be considered the simplicity of the constructive language used in this project. It is given by the complex projective repetition of the type systems and by the establishment of a quasi-mathematical grammar. The systematization of its vocabulary makes, after a deep analysis of its architecture, to recognize new parameters able to document this moment in the history of English architecture. The building envelope is, at the same time, facade and structure. This feature has been overlooked when many photographs of the finished work and its drawings -made by the Smithsons during the design phase- has been exposed over six decades. As a result, it has proliferated the knowledge of Hunstanton Secondary Modern School’s architecture as a more superficial level, just by showing the formal outcome of its project and thus simply been left the sensation of the great influence that Mies Van der Rohe provocated in the Smithson thinking during their first years of developing his work as architects. Therefore, the main objective of this thesis is to facilitate an understanding of the Smithsons’ proposed space. This is made possible through the detailed analysis of the different systems used in it and, by understanding the knowledge of the team involved in its construction. To prove this, it is necessary to pay attention to the study of the materials and to different project mechanisms that make possible to this group of spaces -inner and outer- be defined through the game played by two variables: an apparent austerity in the use of materials and the combination of the various participant systems through the resource of repetition. Despite the untimely interventions made in order to adapt the center to the new needs (the large increase in the number of students), Hunstanton School’s building continues proclaiming its spatial integrity. Assuming that Hunstanton Secondary School’s architecture represents the manifesto of New Brutalism in England, it is concluded that the result of its construction was the result of numerous influences that, in connection with the Smithsons, were present during the years in which its project was conceived. This meaning goes beyond the conclusions made from the architectural debate that was published in many of local architectural magazines. The compositional mechanisms employed, are also linked to what art historians had contributed to the history of architecture until then. Since the 40s, historians had undertaken a new way to tell History. This new mode strongly implied its critical capacity. All this, was causing interferences in the mentality of the architects of the new generation and, giving them a subliminally determined and very subjective cultural background. Of course, the final architectural result had much to do with the material resources available at that time and, with its optimization through the adoption of new working methods as the multidisciplinary organization. The inclusion of engineer Ronald Jenkins in the team of the Smithsons was a great opportunity. He proposed to implement the new Plastic Theory in the structural calculation and thereby he got enrich the spatial results achieved, by enabling the perception of a lightweight construction, despite its large size and, linked to the landscape where it is inserted. But all these conditions were passed through the filter of social regeneration’s desire, following the American society’s model. This American model travelled to Europe in the hands of advertising. And, in the same way that publicity had something to do with the creative process of this architecture, also had a lot to do the knowledge of pop art and its compositional resources.

Montecarlo method applied to comparison of tenders in construction projects.

La comparación de las diferentes ofertas presentadas en la licitación de un proyecto,con el sistema de contratación tradicional de medición abierta y precio unitario cerrado, requiere herramientas de análisis que sean capaces de discriminar propuestas que teniendo un importe global parecido pueden presentar un impacto económico muy diferente durante la ejecución. Una de las situaciones que no se detecta fácilmente con los métodos tradicionales es el comportamiento del coste real frente a las variaciones de las cantidades realmente ejecutadas en obra respecto de las estimadas en el proyecto. Este texto propone abordar esta situación mediante un sistema de análisis cuantitativo del riesgo como el método de Montecarlo. Este procedimiento, como es sabido, consiste en permitir que los datos de entrada que definen el problema varíen unas funciones de probabilidad definidas, generar un gran número de casos de prueba y tratar los resultados estadísticamente para obtener los valores finales más probables,con los parámetros necesarios para medir la fiabilidad de la estimación. Se presenta un modelo para la comparación de ofertas, desarrollado de manera que puede aplicarse en casos reales aplicando a los datos conocidos unas condiciones de variación que sean fáciles de establecer por los profesionales que realizan estas tareas. ABSTRACT: The comparison of the different bids in the tender for a project, with the traditional contract system based on unit rates open to and re-measurement, requires analysis tools that are able to discriminate proposals having a similar overall economic impact, but that might show a very different behaviour during the execution of the works. One situation not easily detected by traditional methods is the reaction of the actual cost to the changes in the exact quantity of works finally executed respect of the work estimated in the project. This paper intends to address this situation through the Monte Carlo method, a system of quantitative risk analysis. This procedure, as is known, is allows the input data defining the problem to vary some within well defined probability functions, generating a large number of test cases, the results being statistically treated to obtain the most probable final values, with the rest of the parameters needed to measure the reliability of the estimate. We present a model for the comparison of bids, designed in a way that it can be applied in real cases, based on data and assumptions that are easy to understand and set up by professionals who wish to perform these tasks.