Bioavailability and extraction of heavy metals from contaminated soil by Atriplex halimus

Pot experiments were performed to evaluate the phytoremediation capacity of plants of Atriplex halimus grown in contaminated mine soils and to investigate the effects of organic amendments on the metal bioavailability and uptake of these metals by plants. Soil samples collected from abandoned mine sites north of Madrid (Spain) were mixed with 0, 30 and 60 Mg ha?1 of two organic amendments, with different pH and nutrients content: pine-bark compost and horse- and sheep-manure compost. The increasing soil organic matter content and pH by the application of manure amendment reduced metal bioavailability in soil stabilising them. The proportion of Cu in the most bioavailable fractions (sum of the water-soluble, exchangeable, acid-soluble and Fe?Mn oxides fractions) decreased with the addition of 60 Mg ha?1 of manure from 62% to 52% in one of the soils studied and from 50% to 30% in the other. This amendment also reduced Zn proportion in water-soluble and exchangeable fractions from 17% to 13% in one of the soils. Manure decreased metal concentrations in shoots of A. halimus, from 97 to 35 mg kg?1 of Cu, from 211 to 98 mg kg?1 of Zn and from 1.4 to 0.6 mg kg?1 of Cd. In these treatments there was a higher plant growth due to the lower metal toxicity and the improvement of nutrients content in soil. This higher growth resulted in a higher total metal accumulation in plant biomass and therefore in a greater amount of metals removed from soil, so manure could be useful for phytoextraction purposes. This amendment increased metal accumulation in shoots from 37 to 138 mg pot?1 of Cu, from 299 to 445 mg pot?1 of Zn and from 1.8 to 3.7 mg pot?1 of Cd. Pine bark amendment did not significantly alter metal availability and its uptake by plants. Plants of A. halimus managed to reduce total Zn concentration in one of the soils from 146 to 130 mg kg?1, but its phytoextraction capacity was insufficient to remediate contaminated soils in the short-to-medium term. However, A. halimus could be, in combination with manure amendment, appropriate for the phytostabilization of metals in mine soils.

Phytoextraction of heavy metals from mine soils using hyperaccumulator plants.

Phytoextraction is an environmental-friendly and cost-effective technology that uses metal hyperaccumulator plants to remove heavy metals from soils. The metals are absorbed by the roots, transported and accumulated in the aerial parts of the plants, which can be harvested and eliminated. The aim of this work was to study some hyperaccumulator species that could be useful to decontaminate mine soils and also to investigate the bioavailability and uptake of these metals by plants with the addition of organic amendments. Pot experiments were performed with soil samples collected from two mining areas in the north of Madrid, where there was an intense mining activity more than 50 years ago. Three species (Thlaspi arvense, Brassica juncea and Atriplex halimus) were grown under controlled conditions in pots filled with contaminated soils mixed with 0 Mg, 30 Mg and 60 Mg per hectare of two different organic amendments: a commercial compost made of pine bark, peat and wood fiber and other made of horse and sheep manure and wood fiber. Plants were harvested at the end of their crop cycle and were digested in order to measure metal concentration (Zn, Cu and Cd) in roots and shoots. Highest plant metal concentration was observed in pots treated with pine bark amendment and with pure soil due to an increase in metal bioavailability with decreasing pH. Also in those treatments the total plant biomass was lower, even some plants could not germinate. On the contrary, there was a lower metal concentration in plant tissues of pots with manure because its higher pH whereas plant growth was significantly larger so there was an incresing amount of metals removed from soil by plants. Comparing the three species results indicate a higher total metal uptake in A. halimus than B. juncea and T. arvense. In conclusion, results show that pH affects metal bioavailability and uptake by hyperaccumulator plants. Addition of organic amendments could be a successful technique for stabilization of metals in contaminated soils.

Bioaccessibility of heavy metals and risk assessment in urban gardens of Madrid

Human health problems and solutions. Urban gardening has spread worldwide in recent years as it enhances food security and selfsupply and promotes community integration. However urban soils are significantly enriched in trace elements relative to background levels. Exposure to the soil in urban gardens may therefore result in adverse health effects depending on the degree of contact during gardening, infant recreational activities and ingestion of vegetables grown in them. In order to evaluate this potential risk, 36 composite samples were collected from the top 20 cm of the soil of 6 urban gardens in Madrid. The aqua regia (pseudototal) and glycine-extractable (bioaccessible) concentrations of Co, Cr, Cu, Ni, Pb and Zn were determined by atomic absorption spectrophotometry. Additionally, pH, texture, Fe, Ca, and Mn concentrations, and organic matter and calcium carbonate contents were determined in all urban gardens and their influence on trace element bioaccessibility was analyzed.

Effects of soluble humic acids on the uptake of heavy metals by Vetiveria zizanioides (L.) Nash in contaminated mining soils

In the past, mining wastes were left wherever they might lie in the surroundings of the mine area. Unfortunately, inactive and abandoned mines continue to pollute our environment, reason why these sites should be restored with minimum impact. Phytoextraction is an environmental-friendly and cost-effective technology less harmful than traditional methods that uses metal hyperaccumulator or at least tolerant plants to extract heavy metals from polluted soils. One disadvantage of hyperaccumulator species is their slow growth rate and low biomass production. Vetiveria zizanioides (L.) Nash, perennial species adapted to Mediterranean climate has a strong root system which can reach up to 3 m deep, is fast growing, and can survive in sites with high metal levels (Chen et al., 2004). Due to the fact that metals in abandoned mine tailings become strongly bonded to soil solids, humic acids used as chelating agents could increase metal bioavailability (Evangelou et al., 2004; Wilde et al., 2005) and thereby promote higher accumulation in the harvestable parts of the plant. The objective of this study was to examine the performance of humic acid assisted phytoextraction using Vetiveria zizanioides (L.) Nash in heavy metals contaminated soils.

Phytoextraction of heavy metals from mine soils using hyperaccumulator plants

The aim of this work was to study some hyperaccumulator species that could be useful to decontaminate mine soils and also to investigate the bioavailability and uptake of these metals by plants with the addition of organic amendments. Pot experiments were performed with soil samples collected from two mining areas in the north of Madrid, where there was an intense mining activity more than 50 years ago. Three species (Thlaspi arvense, Brassica juncea and Atriplex halimus) were grown under controlled conditions in pots filled with contaminated soils mixed with 0 Mg, 30 Mg and 60 Mg per hectare of two different organic amendments: a commercial compost made of pine bark, peat and wood fiber and other made of horse and sheep manure and wood fiber. Plants were harvested at the end of their crop cycle and were digested in order to measure metal concentration (Zn, Cu and Cd) in roots and shoots. Highest plant metal concentration was observed in pots treated with pine bark amendment and with pure soil due to an increase in metal bioavailability with decreasing pH. Also in those treatments the total plant biomass was lower, even some plants could not germinate. On the contrary, there was a lower metal concentration in plant tissues of pots with manure because its higher pH whereas plant growth was significantly larger so there was an incresing amount of metals removed from soil by plants. Comparing the three species results indicate a higher total metal uptake in A. halimus than B. juncea and T. arvense. In conclusion, results show that pH affects metal bioavailability and uptake by hyperaccumulator plants. Addition of organic amendments could be a successful technique for stabilization of metals in contaminated soils.

Evaluating sustainability and food security of peasant farming systems in Mesoamerican highlands

En las últimas décadas, la agricultura sostenible ha sido objeto de gran interés y debate académico, no sólo en términos conceptuales, sino también en términos metodológicos. La persistencia de la inseguridad alimentaria y el deterioro de los recursos naturales en muchas regiones del mundo, ha provocado el surgimiento de numerosas iniciativas centradas en revitalizar la agricultura campesina así como renovadas discusiones sobre el rol que juega la agricultura como motor de desarrollo y principal actividad para alivio de la pobreza. Por ello, cuando hablamos de evaluar sistemas campesinos de montaña, debemos considerar tanto la dimensión alimentaria como las especificidades propias de los sistemas montañosos como base fundamental de la sostenibilidad. Al evaluar la contribución que han hecho alternativas tecnológicas y de manejo en la mejora de la sostenibilidad y la seguridad alimentaria de los sistemas campesinos de montaña en Mesoamérica, surgen tres preguntas de investigación: • ¿Se está evaluando la sostenibilidad de los sistemas campesinos teniendo en cuenta la variabilidad climática, la participación de los agricultores y las dinámicas temporales? • ¿Podemos rescatar tendencias comunes en estos sistemas y extrapolar los resultados a otras zonas? • ¿Son inequívocamente positivas las alternativas propuestas que se han llevado a cabo? En este trabajo se presentan tres evaluaciones de sostenibilidad que tratan de poner de manifiesto cuáles son los retos y oportunidades que enfrentan actualmente los sistemas campesinos de montaña. En primer lugar, se evalúan tres sistemas de manejo agrícola bajo dos años meteorológicamente contrastantes. Se determinó que durante el año que experimentó lluvias abundantes y temperaturas moderadas, los sistemas de bajos insumos, basados en el uso de abonos orgánicos y rotación de cultivos, obtuvieron los mejores resultados en indicadores ecológicos y similares resultados en los económicos y sociales que el sistema de altos insumos químicos. En el segundo año, con heladas tempranas y sequía invernal, la productividad se redujo para todos los sistemas pero los sistemas más diversificados (en variedades de maíz y/o siembra de otros cultivos) pudieron resistir mejor los contratiempos climáticos. En segundo lugar, se evalúa el grado de conocimiento (percepción) campesino para determinar los factores claves que determinan la sostenibilidad de sus sistemas y su seguridad alimentaria. Se determinó que los principales puntos críticos identificados por los campesinos (tamaño de parcela y pendiente del terreno) afectan de forma significativa a cuestiones de índole económica, pero no son capaces de explicar los desequilibrios alimenticios existentes. Realizando un análisis comparativo entre comunidades que presentaban buenos y malos resultados en cuanto a aporte energético y proteico, se determinó que la seguridad alimentaria estaba relacionada con la sostenibilidad de los sistemas y que concretamente estaba ligada a los atributos de equidad y autonomía. Otro resultado destacable fue que las comunidades más marginales y con mayor dificultad de acceso mostraron mayores niveles de inseguridad alimentaria, pero la variabilidad intergrupal fue muy alta. Eso demuestra que la seguridad alimentaria y nutricional forma parte de un complejo sistema de estrategias de autoabastecimiento ligada a la idiosincrasia misma de cada uno de los hogares. En tercer lugar, se evaluó el desempeño de las escuelas de campo de agricultores (ECAs) en la mejora de la sostenibilidad y la seguridad alimentaria de un sistema campesino de montaña. Para ver el efecto del impacto de estas metodologías a largo plazo, se estudiaron tres comunidades donde se habían implementado ECAs hace 8, 5 y 3 años. Encontramos que el impacto fue progresivo ya que fue la comunidad más antigua la que mejores valores obtuvo. El impacto de las ECAs fue rápido y persistente en los indicadores relacionados con la participación, el acceso a servicios básicos y la conservación de los recursos naturales. El estudio demostró un claro potencial de las ECAs en la mejora general de la sostenibilidad y la seguridad alimentaria de estos sistemas, sin embargo se observó una relación directa entre el aumento de producción agrícola y el uso de insumos externos, lo que puede suponer un punto crítico para los ideales sostenibles. ABSTRACT During the last decades, sustainable agriculture has been the subject of considerable academic interest and debate, not only in conceptual terms, but also in methodological ones. The persistence of high levels of environmental degradation and food insecurity in many regions has led to new initiatives focused on revitalizing peasant agriculture and renewed discussions of the role of sustainable agriculture as an engine for development, environmental conservation and poverty alleviation. Therefore, to assess mountain farming systems, we must consider food dimension and taking into account the specificities of the mountain systems as the foundation of sustainability. When evaluating contribution of technological and management alternative proposals in achieving sustainability and food security for peasant farming systems in Mesoamerican highlands, three research questions arise: • Is sustainability of peasant-farming systems being evaluated taking into account climate variability, participation of farmers and temporal dynamics? • Can we rescue common trends in these systems and extrapolate the results to other areas? • What alternative proposals that have been conducted are unequivocally positives? In this document, we present three evaluations of sustainability that try to highlight the challenges and opportunities that currently face mountain farming systems in Mesoamerica. First, we evaluate the sustainability of three agricultural management systems in two contrasting weather years. We determined that during the first year that exposed heavy rains and moderate temperatures, low-input systems, which are based on the use of organic fertilizers and crop rotation, provided better results in terms of ecological indicators and equal results in terms of economic and social indicators than those achieved using a high chemical input system. In the second year, which featured early frosts and a winter drought, productivity declined in all systems; however, the most diversified systems (in terms of the maize varieties grown and the sowing of other crops) more successfully resisted these climatic adversities. Second, we evaluate the farmers’ perception to determine the key drivers for achieving their sustainability and food and nutritional security. We determined that the key factors identified by farmers (landholding size and slope of cropland) exerted significant impacts on economic disparities but did not explain the malnutrition levels. We compared two contrasting hamlets according to their energy and protein supply, one namely Limón Timoté (LT), which did not present food problems and Limón Peña Blanca (LP), which did exhibit food insecurity. The results showed that FNS is linked to sustainability, and it is primarily related to the sustainability attributes of self-reliance and equity. Although the more marginated and inaccessible community exhibited more food insecurity, food and nutritional security depend upon a complex array of self-sufficiency strategies that remain linked to individual household idiosyncrasies. Third, we evaluated the impact of farmer field schools for improving the sustainability and food security of peasant mountain systems. In order to appreciate the long-term impact, we studied three communities where FFSs were implemented eight, five and three years ago, respectively. We found that FFSs have a gradual impact, as the community that first implemented FFSs scores highest. The impact of FFSs was broad and long-lasting for indicators related to participation, access to basic services and conservation of natural resources. This study demonstrates the potential of FFSs, but more attention will have to be paid to critical indicators in order to scale up their potential in the future. We observed a direct relationship between the increase in agricultural production and the use of external inputs, which is a critical point for sustainable ideals.

Comparativa de métodos de descontaminación de suelos afectados por hidrocarburos. Aplicación a la obra del AVE de Málaga

El objetivo de esta tesis, va a ser la investigación y desarrollo de tratamientos de biorremediación para conseguir la recuperación de los terrenos contaminados situados en el tramo del tren de alta velocidad entre Córdoba y Málaga, reduciendo de esta forma los residuos enviados a vertederos. Para ello, se va a investigar y a desarrollar una tecnología innovadora de descontaminación in situ de suelos con altas concentraciones de hidrocarburos, basándonos en el landfarming y como principal avance la coexistencia con hidróxido de magnesio, elemento no utilizado nunca y potencialmente muy útil. Se va a pretender reducir la concentración final de hidrocarburos y el tiempo de tratamiento, sin transportar a vertedero los residuos. Se desean conseguir las condiciones ambientales óptimas que permitan potenciar la degradación microbiana de los hidrocarburos y sus productos residuales en corto tiempo Se va a investigar el empleo del hidróxido de magnesio como complemento al landfarming y a buscar las sinergias de este compuesto como gran fijador de metales pesados. ABSTRACT The aim of this thesis will be the research and development of bioremediation treatments for the recovery of contaminated land in the stretch of the high speed train between Cordoba and Malaga, thereby reducing waste sent to landfills. To do this, is to research and develop innovative technology for in situ remediation of soil with high concentrations of hydrocarbons, based on the main progress landfarming and coexistence with magnesium hydroxide, item never used and potentially very useful. It will pretend to reduce the final hydrocarbon concentration and treatment time, without transporting waste landfill. They want to get the optimum environmental conditions for enhancing microbial degradation of hydrocarbons and waste products in a short time It will investigate the use of magnesium hydroxide as a complement to landfarming and seek synergies of this compound as a great fixer of heavy metals.

Composition, potential emissions and agricultural value of pig slurry from Spanish commercial farms

Pig slurry is a valuable fertilizer for crop production but at the same time its management may pose environmental risks. Slurry samples were collected from 77 commercial farms of four animal categories (gestating and lactating sows, nursery piglets and growing pigs) and analyzed for macronutrients, micronutrients, heavy metals and volatile fatty acids. Emissions of ammonia (NH3) and biochemical methane potential (BMP) were quantified. Slurry electrical conductivity, pH, dry matter content and ash content were also determined. Data analysis included an analysis of correlations among variables, the development of prediction models for gaseous emissions and the analysis of nutritional content of slurries for crop production. Descriptive information is provided in this work and shows a wide range of variability in all studied variables. Animal category affected some physicochemical parameters, probably as a consequence of different slurry management and use of cleaning water. Slurries from gestating sows and growing pigs tended to be more concentrated in nutrients, whereas the slurry from lactating sows and nursery piglets tended to be more diluted. Relevant relationships were found among slurry characteristics expressed in fresh basis and gas emissions. Predictive models using on-farm measurable parameters were obtained for NH3 (R2 = 0.51) and CH4

Remediation of crude oil contaminated soils by means of bitumen emulsions

Effective remediation of contaminated sites with oils, heavy metals and other chemical agents is one of the most important environmental problems all over the world. Contaminated soils by petroleum from different sites and origins, might contaminate groundwater aquifers and then be spread by rain. Many years and the requirement of remedial techniques may be needed to remediate them. However, previous experiences show the uselessness of these methods for the solution of all problems. As any case of soil contamination is different, specific studies with relevant factors at financial aspects, legal limits and waste and soil characteristics are needed. In this work, a study of the use of bitumen asphalt emulsion to remediate contaminated soils by crude oils is exposed. By means of the soil stabilization technology, using the contaminated soils as aggregates and the tailor made emulsion as binder, the feasibility of the mix application to produce stable and resistant pavements is demonstrated

Spatial and temporal variations of trace element distribution in soils and street dust of an industrial town in NW Spain: 15 years of study

Extensive spatial and temporal surveys, over 15 years, have been conducted in soil in urban parks and street dusts in one of the most polluted cities in western Europe, Avilés (NW Spain). The first survey was carried out in 1996, and since then monitoring has been undertaken every five years. Whilst the sampling site is a relatively small town, industrial activities (mainly the steel industry and Zn and Al metallurgy) and other less significant urban sources, such as traffic, strongly affect the load of heavy metals in the urban aerosol. Elemental tracers have been used to characterise the influence of these sources on the composition of soil and dust. Although PM10 has decreased over these years as a result of environmental measures undertaken in the city, some of the “industrial” elements still remain in concentrations of concern for example, up to 4.6% and 0.5% of Zn in dust and soil, respectively. Spatial trends in metals such as Zn and Cd clearly reflect sources from the processing industries. The concentrations of these elements across Europe have reduced over time, however the most recent results from Avilés revealed an upward trend in concentration for Zn, Cd, Hg and As. A risk assessment of the soil highlighted As as an element of concern since its cancer risk in adults was more than double the value above which regulatory agencies deem it to be unacceptable. If children were considered to be the receptors, then the risk nearly doubles from this element.

Análisis de la degradación, desintegración y biodegradabilidad de bolsas de poliéster y almidón en compostaje de residuos urbanos: escalas de laboratorio e industrial

El principal objetivo de esta tesis es verificar que las bolsas biodegradables de copoliéster (PBAT) con base de almidón (UNE 13432: 2001) alcanzan los niveles de degradación y desintegración requeridos para su certificación (%D= ≥ 90%), medido en condiciones reales de compostaje industrial. Para lograr mayor representatividad, los ensayos se han realizado en dos plantas de tratamiento de residuos urbanos en las que se aplican las técnicas de compostaje más comunes en el ámbito europeo y nacional, pila y túnel, mediante el compostaje de la FORSU. Se llevaron a cabo dos tipos de ensayos. Por un lado se realizó un ensayo escala de laboratorio (ISO 14855), orientado como indicador de la biodegradabilidad del polímero en el formato bolsa comercializado. Por otro lado, se desarrollaron una batería de ensayos realizados en dos plantas de compostaje de residuos urbanos: el Centro de Tratamiento de Residuos de Torija (Ávila), que realiza el compostaje mediante pila volteada, y el Centro de Tratamiento de Residuos de Arenas de San Pedro (Ávila), que realiza el compostaje en túnel. Para la obtención de resultados se han contrastado parámetros como el porcentaje de biodegradación (%B), el porcentaje de desintegración (%D), degradación superficial de las muestras, calidad de la FORSU inicial (caracterizaciones y análisis físico-químico) y calidad del MB final (análisis físico-químico e IG). Atendiendo al objetivo general se demuestra que las bolsas de copoliéster con base de almidón certificadas (UNE EN 13432:2001) han alcanzado el 94,37% ± 0,007% de desintegración en la planta de compostaje de FORSU con pila volteada; y el 86,36% ± 0,151% en la planta de compostaje de FORSU con túnel estático. A pesar de la aparente diferencia, el resultado del análisis concluye que no existen diferencias estadísticamente significativas entre técnicas de compostaje. La presencia de impropios y el contendido de metales pesados en la FORSU no han influido en la desintegración de las bolsas de estudio. En cambio, se ha detectado una influencia estadísticamente significativa entre el contenido de materia orgánica total y de nutrientes de la FORSU y el porcentaje de desintegración de las muestras. No se detectado una relación estadísticamente significativa entre la presencia de bolsas de estudio en las concentraciones definidas, y la calidad del MB, medido mediante el análisis físico-químico, microbiológico y el IG del MB. La concentración de los metales pesados en la mayoría de las muestras de material bioestabilizado cumplió con los límites establecidos para la categoría A, aplicable al “compost” procedente de la fracción orgánica recogida de forma separada según el RD 506/2013 de productos fertilizantes. También se detectó fitotoxicidad alta (FA) según la metodología y criterios de valoración definidos. Esta fitotoxicidad no está relacionada con la presencia de las bolsas de estudio sino con la calidad de la FORSU de partida y/o con los productos liberados durante el proceso de compostaje. ABSTRACT The main objective of this thesis is to verify that the copolyester (PBAT) starch based (UNE 13432: 2001) biodegradable bags reach levels of degradation and disintegration required for it´s certification (% D = ≥ 90%), measured in terms of real industrial composting. The tests were performed at two municipal solid waste (MSW) treatment plants, where the most common composting techniques applied at European and national level were represented, windrow and tunnel. Two types of tests were carried out: First, a laboratory scale test (ISO 14855), as an indicator of the polymer biodegradation of the commercialized bag format. Second, a battery of tests was conducted at two MSW composting plants, Waste Treatment Center of Torija (Guadalajara), that makes compost by turned pile, and the Waste Treatment Center of Arenas de San Pedro (Ávila), where makes compost by static tunnel. To obtain the results, the parameters such as the biodegradation percentage (% B), the disintegration percentage (% D), surface degradation of the samples, the initial quality of FORSU (characterizations and physico-chemical analysis) and bioestabilithated material (MB) quality (physico-chemical analysis and IG) have been compared. In reference to the general aim It shows that the copolyester starch based certified (UNE-EN 13432) bags have reached 94.37% ± 0.007% of disintegration in the composting turned pile; and 86.36% ± 0.151% in the static tunnel. Despite the apparent difference, the result of the analysis concludes that there are no statistically significant differences between composting techniques. The presence of non-compostable materials and the heavy metals content in the FORSU has not affected in the disintegration of the bags. Instead, It has been detected a statistically significant influence over the total organic matter content and nutrient content in the FORSU and the samples disintegration percentage. A statistically significant relationship between the bag presence in the defined concentrations and the quality of MB measured by physical-chemical analysis, microbiological analysis and IG of the MB is not detected. The concentration of heavy metals in most MB samples was within the limits of A-Class, applicable to "compost" from organic waste collected separately according to RD 506/2013 of fertilizers. High phytotoxicity (FA) was also detected according to the methodology and evaluation defined. The phytotoxicity is not related to the presence of bags but it is with the FORSU initial quality and/or with the products released during the composting process.

Compostabilidad de envases de bolsas de PBAT+PLA y envases rígidos de PLA mediante tecnologías de pila y túnel

Los polímeros compostables suponen en torno al 30% de los bioplásticos destinados a envasado, siendo a su vez esta aplicación el principal destino de la producción de este tipo de materiales que, en el año 2013, superó 1,6 millones de toneladas. La presente tesis aborda la biodegradación de los residuos de envases domésticos compostables en medio aerobio para dos tipos de formato y materiales, envase rígido de PLA (Clase I) y dos tipos de bolsas de PBAT+PLA (Clases II y III). Sobre esta materia se han realizado diversos estudios en escala de laboratorio pero para otro tipo de envases y biopolímeros y bajo condiciones controladas del compost con alguna proyección particularizada en plantas. La presente tesis da un paso más e investiga el comportamiento real de los envases plásticos compostables en la práctica del compostaje en tecnologías de pila y túnel, tanto a escala piloto como industrial, dentro del procedimiento y con las condiciones ambientales de instalaciones concretas. Para ello, con el método seguido, se han analizado los requisitos básicos que debe cumplir un envase compostable, según la norma UNE – EN 13432, evaluando el porcentaje de biodegradación de los envases objeto de estudio, en función de la pérdida de peso seco tras el proceso de compostaje, y la calidad del compost obtenido, mediante análisis físico-químico y de fitotoxicidad para comprobar que los materiales de estudio no aportan toxicidad. En cuanto a los niveles de biodegrabilidad, los resultados permiten concluir que los envases de Clase I se compostan adecuadamente en ambas tecnologías y que no requieren de unas condiciones de proceso muy exigentes para alcanzar niveles de biodegradación del 100%. En relación a los envases de Clase II, se puede asumir que se trata de un material que se composta adecuadamente en pila y túnel industrial pero que requiere de condiciones exigentes para alcanzar niveles de biodegradación del 100% al afectarle de forma clara la ubicación de las muestras en la masa a compostar, especialmente en el caso de la tecnología de túnel. Mientras el 90% de las muestras alcanza el 100% de biodegradación en pila industrial, tan sólo el 50% lo consigue en la tecnología de túnel a la misma escala. En cuanto a los envases de Clase III, se puede afirmar que es un material que se composta adecuadamente en túnel industrial pero que requiere de condiciones de cierta exigencia para alcanzar niveles de biodegradación del 100% al poderle afectar la ubicación de las muestras en la masa a compostar. El 75% de las muestras ensayadas en túnel a escala industrial alcanzan el 100% de biodegradación y, aunque no se ha ensayado este tipo de envase en la tecnología de pila al no disponer de muestras, cabe pensar que los resultados de biodegrabilidad que hubiera podido alcanzar habrían sido, como mínimo, los obtenidos para los envases de Clase II, al tratarse de materiales muy similares en composición. Por último, se concluye que la tecnología de pila es más adecuada para conseguir niveles de biodegradación superiores en los envases tipo bolsa de PBAT+PLA. Los resultados obtenidos permiten también sacar en conclusión que, en el diseño de instalaciones de compostaje para el tratamiento de la fracción orgánica recogida selectivamente, sería conveniente realizar una recirculación del rechazo del afino del material compostado para aumentar la probabilidad de someter este tipo de materiales a las condiciones ambientales adecuadas. Si además se realiza un triturado del residuo a la entrada del proceso, también se aumentaría la superficie específica a entrar en contacto con la masa de materia orgánica y por tanto se favorecerían las condiciones de biodegradación. En cuanto a la calidad del compost obtenido en los ensayos, los resultados de los análisis físico – químicos y de fitotoxicidad revelan que los niveles de concentración de microorganismo patógenos y de metales pesados superan, en la práctica totalidad de las muestras, los niveles máximos permitidos en la legislación vigente aplicable a productos fertilizantes elaborados con residuos. Mediante el análisis de la composición de los envases ensayados se constata que la causa de esta contaminación reside en la materia orgánica utilizada para compostar en los ensayos, procedente del residuo de origen doméstico de la denominada “fracción resto”. Esta conclusión confirma la necesidad de realizar una recogida selectiva de la fracción orgánica en origen, existiendo estudios que evidencian la mejora de la calidad del residuo recogido en la denominada “fracción orgánica recogida selectivamente” (FORM). Compostable polymers are approximately 30% of bioplastics used for packaging, being this application, at same time, the main destination for the production of such materials exceeded 1.6 million tonnes in 2013. This thesis deals with the biodegradation of household packaging waste compostable in aerobic medium for two format types and materials, rigid container made of PLA (Class I) and two types of bags made of PBAT + PLA (Classes II and III). There are several studies developed about this issue at laboratory scale but for other kinds of packaging and biopolymers and under composting controlled conditions with some specifically plants projection. This thesis goes one step further and researches the real behaviour of compostable plastic packaging in the composting practice in pile and tunnel technologies, both at pilot and industrial scale, within the procedure and environmental conditions of concrete devices. Therefore, with a followed method, basic requirements fulfilment for compostable packaging have been analysed according to UNE-EN 13432 standard. It has been assessed the biodegradability percentage of the packaging studied, based on loss dry weight after the composting process, and the quality of the compost obtained, based on physical-chemical analysis to check no toxicity provided by the studied materials. Regarding biodegradability levels, results allow to conclude that Class I packaging are composted properly in both technologies and do not require high exigent process conditions for achieving 100% biodegradability levels. Related to Class II packaging, it can be assumed that it is a material that composts properly in pile and tunnel at industrial scale but requires exigent conditions for achieving 100% biodegradability levels for being clearly affected by sample location in the composting mass, especially in tunnel technology case. While 90% of the samples reach 100% of biodegradation in pile at industrial scale, only 50% achieve it in tunnel technology at the same scale. Regarding Class III packaging, it can be said that it is a material properly composted in tunnel at industrial scale but requires certain exigent conditions for reaching 100% biodegradation levels for being possibly affected by sample location in the composting mass. The 75% of the samples tested in tunnel at industrial scale reaches 100% biodegradation. Although this kind of packaging has not been tested on pile technology due to unavailability of samples, it is judged that biodegradability results that could be reached would have been, at least, the same obtained for Class II packaging, as they are very similar materials in composition. Finally, it is concluded that pile technology is more suitable for achieving highest biodegradation levels in bag packaging type of PBAT+PLA. Additionally, the obtained results conclude that, in the designing of composting devices for treatment of organic fraction selectively collected, it would be recommended a recirculation of the refining refuse of composted material in order to increase the probability of such materials to expose to proper environmental conditions. If the waste is grinded before entering the process, the specific surface in contact with organic material would also be increased and therefore biodegradation conditions would be more favourable. Regarding quality of the compost obtained in the tests, physical-chemical and phytotoxicity analysis results reveal that pathogen microorganism and heavy metals concentrations exceed, in most of the samples, the maximum allowed levels by current legislation for fertilizers obtained from wastes. Composition analysis of tested packaging verifies that the reason for this contamination is the organic material used for composting tests, comes from the household waste called “rest fraction”. This conclusion confirms the need of a selective collection of organic fraction in the origin, as existing studies show the quality improvement of the waste collected in the so-called “organic fraction selectively collected” (FORM).

Respuesta transcripcional de Populus a bifenilos policlorados: Aspectos aplicados a la fitorremediación

La degradación del suelo ha adquirido una magnitud preocupante. Los métodos tradicionales de descontaminación, son costosos e insuficientes. La fitorremediación representa una alternativa eficaz, de bajo coste, respetuosa con el medio ambiente, que además mejora las propiedades del suelo, si bien ha habido desarrollos relevantes en la última década. Desde el punto de vida científico, el reto principal es descifrar las rutas metabólicas implicadas en respuesta a contaminantes y comprender su regulación. Esta información es imprescindible si aspiramos a mejorar las capacidades naturales de algunas especies vegetales para remediar los suelos contaminados. Los estudios de esta Tesis se han centrado en Populus, el mejor modelo forestal disponible a raíz de la secuenciación de su genoma completo. Por otra parte, Populus tiene una gran capacidad natural para la degradación de contaminantes orgánicos, lo que explica su predominio en los programas forestales de fitorremediación que se desarrollan actualmente. Hemos elegido en concreto al híbrido Populus tremula x P. alba, por la facilidad con que se cultiva y su particular interés biotecnológico. La presente Tesis plantea un estudio comprehensivo de la respuesta molecular a bifenilos policlorados (PCBs), una familia de contaminantes orgánicos persistentes de particular relevancia a escala mundial. Se ha utilizado para ello una aproximación transcriptómica, basada en tecnología RNA-seq, para identificar los genes implicados en el metabolismo de los compuestos in planta y cuantificar sus niveles de activación en distintas situaciones controladas. La tesis pretende asimismo definir el control transcripcional subyacente a la respuesta bioquímica frente a este tipo de contaminantes. Resulta sorprendente que dicha respuesta sea prácticamente desconocida a nivel molecular, a pesar de su gran potencial aplicado en el contexto de la tecnología fitorremediadora. Para desarrollar este proyecto aplicamos a nuestros cultivos de chopo híbridos concentraciones diferentes de Aroclor 1221, una mezcla de PCBs muy utilizada a nivel comercial durante décadas, su uso está prohibido hoy internacionalmente. Y tomamos muestras de RNA a dos concentraciones y dos momentos distintos de exposición al contaminante, generando así una matriz de cuatro elementos con sus controles correspondientes. Con el fin de incrementar la especificidad de nuestro análisis, consideramos sobre todo los genes diferencialmente expresados más significativos según cuatro algoritmos estadísticos distintos. Por otra parte, realizamos análisis funcionales con herramientas bioinformáticas basadas en comparaciones de secuencias y en redes de co-expresión génica. La respuesta de los genes de particular interés fue validada mediante tecnología qRT-PCR (reacción de la polimerasa en cadena cuantitativa en tiempo real). Se trata del primer estudio comprehensivo de la respuesta de un organismo vegetal ante la presencia de PCBs. Este estudio nos ha permitido identificar una cantidad considerable de genes estructurales y reguladores, definiendo nuevos factores de transcripción cuya expresión es proporcional a la concentración de contaminante en el medio o al tiempo de exposición al mismo. Los análisis de correlación nos permiten afirmar en que la respuesta metabólica a PCBs, incluyendo posibles rutas degradadoras, participan en al menos quince factores de transcripción y unas cuarenta proteínas o enzimas que resultan particularmente inducidas. Entre las familias implicadas destacan los citocromos P450, la glutatión transferasas, las deshidrogenasas reductasas (short-chain dehydrogenase reductase) y las proteínas MDR (multi-drug resistance). Mientras que los factores de transcripción encontrados pertenecen a la familia de ZF-TF, MYBs, WRKYs entre otros. También identificamos proteínas de función desconocida que no se habían vinculado previamente a este tipo de respuestas en plantas, como la CSP (cold-shock domain proteins). Para estudiar su posible relación con la presencia de PCBs, se caracterizó un gen de esta familia detectado mediante espectrometría de masas en tándem (MS/MS) a partir de mapas IEF x SDS-PAGE (isoelectro focusing x sodium dodecyl sulphate- polyacrylamide gel electrophoresis) de alta resolución. Mediante qRT-PCR pudimos confirmar la inducción del gen correspondiente, ortólogo a PtCSP4 de P. trichocarpa (Potri.004g172600), en respuesta a Aroclor 1221. El análisis fenotípico de las líneas transgénicas de Arabidopsis thaliana que sobre-expresaba la proteína CSP de chopo híbrido confirmó un papel para la misma tolerancia a PCBs, posiblemente a través de mecanismos reguladores que activan proteínas MDR. Este trabajo, además de aportar datos novedosos sobre los mecanismos moleculares desencadenados por la presencia de un PCB en Populus, utilizado aquí como sistema modelo. Con ello se demuestra el potencial de las especies arbóreas no solo como agentes descontaminantes, ya explotado comercialmente, sino también como fuente potencial de genes interesantes. Entre los genes identificados en esta Tesis hay candidatos evidentes a participar en mecanismos de tolerancia al estrés inducido por la contaminación y también rutas metabólicas degradadores de PCBs. Precisamente la posibilidad de degradar al contaminante confiere particular interés a este tipo de estudios frente a la fitorremediación de metales pesados y otros contaminantes elementales. La comparación de los datos generados en este estudio con estudios análogos que se realicen en el futuro con otras especies y xenobióticos, contribuirán a definir mejor la respuesta de las plantas ante la contaminación orgánica y mejorar su potencial descontaminante. ABSTRACT Soil degradation has acquired a disturbing magnitude. Traditional methods of decontamination are expensive and insufficient. Phytoremediation represent an effective alternative, low cost, respectful of the environment, that also improves soil properties, although there have been relevant developments in the last decade. From a life scientist, the challenge is to decipher the major metabolic pathways involved in response to pollutants and understand their regulation. This information is essential if we desire to enhance the natural abilities of some plant species to remediate contaminated soils. This thesis studies have focused on Populus, the best available forestry model following the sequencing of the entire genome. Moreover, Populus has a natural ability to degrade organic pollutants, which explains its predominance in phytoremediation forestry programs currently being developed. We have chosen specifically to hybrid Populus tremula x P. alba, the ease with which it is grown and its particular biotechnological interest. This thesis presents a comprehensive study of the molecular response to polychlorinated biphenyls (PCBs), a family of persistent organic pollutants of particular relevance worldwide. It has been used for a transcriptomic approach using RNA-seq technology, to identify genes involved in the metabolism of compounds in plant and quantify their levels of activation in different controlled situations. The thesis also aims to define the underlying transcriptional control the biochemical response to these pollutants. It is surprising that the response is virtually unknown at the molecular level, despite its great potential applied in the context of phytoremediation technology. To develop this project we applied our hybrid poplar crops different concentrations of Aroclor 1221, a mixture of PCBs widely used commercially for decades, its use is now banned internationally. And we RNA samples at two different concentrations and times of exposure to the pollutant, generating an array of four elements with their corresponding controls. In order to increase the specificity of our analysis, we consider mainly the most significant differentially expressed genes in four different statistical algorithms. Moreover, functional analyzes conducted with bioinformatics tools based on sequence comparisons and networks gene co-expression. The response of genes of particular interest was validated by qRT-PCR (polymerase reaction chain in real-time quantitative. This is the first comprehensive study of the response of a plant organism in the presence of PCBs. This study allowed us to identify a considerable amount of structural and regulatory genes, defining new transcription factors whose expression is proportional to the concentration of contaminant in the middle or at the time of exposure. Correlation analyzes allow us to affirm that the metabolic response to PCBs, including possible degradative pathways, at least fifteen involved in transcription factors and forty proteins or enzymes which are particularly induced. Among the families involved include cytochromes P450, the glutathione transferases, dehydrogenases reductases (short -chain dehydrogenase reductase) and MDR proteins (multi - drug resistance). While transcription factors belong to the family found ZF-TF, MYBs, WRKYs among others. We also identify proteins of unknown function that had not been previously linked to such responses in plants such as CSP (cold- shock domain proteins). To study their possible relationship with the presence of PCBs, a gene in this family was characterized and was detected by tandem mass spectrometry (MS/MS) from maps IEF x SDS -PAGE (sodium dodecyl isoelectro x sulphate- polyacrylamide gel electrophoresis) of high resolution. By qRT -PCR could confirm the induction of the corresponding gene, ortholog to PtCSP4 of P. trichocarpa (Potri.004g172600), in response to Aroclor 1221. Phenotypic analysis of transgenic Arabidopsis thaliana lines over- expressing the protein CSP poplar hybrid confirmed a role for PCBs same tolerance, possibly through regulatory mechanisms activated MDR proteins. This work, in addition to providing new data on the molecular mechanisms triggered by the presence of PCBs in Populus, used here as a model system. Thus the potential of tree species not only as decontamination agents, and commercially exploited, but also as a potential source of interesting genes is shown. Among the genes identified in this thesis there are evident candidates to participate in tolerance mechanisms to stress induced by pollution and degrading metabolic pathways of PCBs. Precisely the possibility of degrading the pollutant attaches particular interest to this type of study off the phytoremediation of heavy metals and other elemental pollutants. The comparison of the data generated in this study with similar studies carried out in the future with other species and xenobiotics contribute to better define the response of plants to organic pollution and improve their decontamination potential.