Determination of the uptake and translocation of nitrogen applied at different growth stages of a melon crop (Cucumis melo L.) using 15N isotope.

In order to establish a rational nitrogen (N) fertilisation and reduce groundwater contamination, a clearer understanding of the N distribution through the growing season and its dynamics inside the plant is crucial. In two successive years, a melon crop (Cucumis melo L. cv. Sancho) was grown under field conditions to determine the uptake of N fertiliser, applied by means of fertigation at different stages of plant growth, and to follow the translocation of N in the plant using 15N-labelled N. In 2006, two experiments were carried out. In the first experiment, labelled 15N fertiliser was supplied at the female-bloom stage and in the second, at the end of fruit ripening. Labelled 15N fertiliser was made from 15NH415NO3 (10 at.% 15N) and 9.6 kg N ha−1 were applied in each experiment over 6 days (1.6 kg N ha−1 d−1). In 2007, the 15N treatment consisted of applying 20.4 kg N ha−1 as 15NH415NO3 (10 at.% 15N) in the middle of fruit growth, over 6 days (3.4 kg N ha−1 d−1). In addition, 93 and 95 kg N ha−1 were supplied daily by fertigation as ammonium nitrate in 2006 and 2007, respectively. The results obtained in 2006 suggest that the uptake of N derived from labelled fertiliser by the above-ground parts of the plants was not affected by the time of fertiliser application. At the female-flowering and fruit-ripening stages, the N content derived from 15N-labelled fertiliser was close to 0.435 g m−2 (about 45% of the N applied), while in the middle of fruit growth it was 1.45 g m−2 (71% of the N applied). The N application time affected the amount of N derived from labelled fertiliser that was translocated to the fruits. When the N was supplied later, the N translocation was lower, ranging between 54% at female flowering and 32% at the end of fruit ripening. Approximately 85% of the N translocated came from the leaf when the N was applied at female flowering or in the middle of fruit growth. This value decreased to 72% when the 15N application was at the end of fruit ripening. The ammonium nitrate became available to the plant between 2 and 2.5 weeks after its application. Although the leaf N uptake varied during the crop cycle, the N absorption rate in the whole plant was linear, suggesting that the melon crop could be fertilised with constant daily N amounts until 2–3 weeks before the last harvest.

Changes in the Papez Circuit in early stages of Alzheimer's Disease

Alzheimer's disease (AD) is the most common cause of demenMa. Neuronal and synapMc losses occur iniMally and predominantly in the medial temporal lobe structures including hippocampus, amygdala and thalamus, structures that belong to the Papez circuit. The integrity of the connecMons amongst them is essenMal for episodic memory, which is specifically impaired in AD. For this reason we have invesMgated the degeneraMon paRern of subcorMcal structures and its relaMon to early stages of AD, i.e. Mild CogniMve Impairment (MCI), both in the amnesic and mulMdomain types using structural magneMc resonance imaging (using a 3T GE scanner) and VBM‐DARTEL.

Diseño y aplicación de una metodología prospectiva para la determinación de los condicionantes futuros del crecimiento de los grandes buques portacontenedores

Durante las últimas décadas se observa una tendencia sostenida al crecimiento en las dimensiones de los grandes buques portacontenedores, que produce, que las infraestructuras portuarias y otras destinadas al tráfico de contenedores deban adaptarse para poder brindar los servicios correspondientes y mantenerse competitivas con otras para no perder el mercado. Esta situación implica importantes inversiones y modificaciones en los sistemas de transporte de contenedores por el gran volumen de carga que se debe mover en un corto periodo de tiempo, lo que genera la necesidad de tomar previsiones relacionadas con la probable evolución a futuro de las dimensiones que alcanzarán los grandes buques portacontenedores. En relación a los aspectos citados surge la inquietud de determinar los condicionantes futuros del crecimiento de los grandes buques portacontenedores, con una visión totalizadora de todos los factores que incidirán en los próximos años, ya sea como un freno o un impulso a la tendencia que se verifica en el pasado y en el presente. En consideración a que el tema a tratar y resolver se encuentra en el futuro, con un horizonte de predicción de veinte años, se diseña y se aplica una metodología prospectiva, que permite alcanzar conclusiones con mayor grado de objetividad sobre probables escenarios futuros. La metodología prospectiva diseñada, conjuga distintas herramientas metodológicas, cualitativas, semi-cuantitativas y cuantitativas que se validan entre sí. Sobre la base del pasado y el presente, las herramientas cuantitativas permiten encontrar relaciones entre variables y hacer proyecciones, sin embargo, estas metodologías pierden validez más allá de los tres a cuatro años, por los vertiginosos y dinámicos cambios que se producen actualmente, en las áreas política, social y económica. Las metodologías semi-cuantitativas y cualitativas, empleadas en forma conjunta e integradas, permiten el análisis de circunstancias del pasado y del presente, obteniendo resultados cuantitativos que se pueden proyectar hacia un futuro cercano, los que integrados en estudios cualitativos proporcionan resultados a largo plazo, facilitando considerar variables cualitativas como la creciente preocupación por la preservación del medio ambiente y la piratería. La presente tesis, tiene como objetivo principal “identificar los condicionantes futuros del crecimiento de los grandes buques portacontenedores y determinar sus escenarios”. Para lo cual, la misma se estructura en fases consecutivas y que se retroalimentan continuamente. Las tres primeras fases son un enfoque sobre el pasado y el presente, que establece el problema a resolver. Se estudian los antecedentes y el estado del conocimiento en relación a los factores y circunstancias que motivaron y facilitaron la tendencia al crecimiento de los grandes buques. También se estudia el estado del conocimiento de las metodologías para predecir el futuro y se diseña de una metodología prospectiva. La cuarta fase, denominada Resultados, se desarrolla en distintas etapas, fundamentadas en las fases anteriores, con el fin de resolver el problema dando respuestas a las preguntas que se formularon para alcanzar el objetivo fijado. En el proceso de esta fase, con el objeto de predecir probables futuros, se aplica la metodología prospectiva diseñada, que contempla el análisis del pasado y el presente, que determina los factores cuya influencia provocó el crecimiento en dimensiones de los grandes buques hasta la actualidad, y que constituye la base para emplear los métodos prospectivos que permiten determinar qué factores condicionarán en el futuro la evolución de los grandes buques. El probable escenario futuro formado por los factores determinados por el criterio experto, es validado mediante un modelo cuantitativo dinámico, que además de obtener el probable escenario futuro basado en las tendencias de comportamiento hasta el presente de los factores determinantes considerados, permite estudiar distintos probables escenarios futuros en función de considerar un cambio en la tendencia futura de los factores determinantes. El análisis del pasado indica que la tendencia al crecimiento de los grandes buques portacontenedores hasta el presente, se ha motivado por un crecimiento económico mundial que se tradujo en un aumento del comercio internacional, particularmente entre los países de Asia, con Europa y Estados Unidos. Esta tendencia se ha visto favorecida por el factor globalización y la acelerada evolución tecnológica que ha permitido superar los obstáculos que se presentaron. Es de destacar que aún en periodos de crisis económicas, con pronósticos de contracciones en el comercio, en los últimos años continuó la tendencia al crecimiento en dimensiones, en busca de una economía de escala para el transporte marítimo de contenedores, en las rutas transoceánicas. La investigación de la evolución de los grandes buques portacontenedores en el futuro, se efectúa mediante el empleo de una metodología prospectiva en la que el criterio experto se valida con un método cuantitativo dinámico, y además se fundamenta en una solida base pre-prospectiva. La metodología diseñada permite evaluar con un alto grado de objetividad cuales serán los condicionantes que incidirán en el crecimiento en tamaño de los grandes buques portacontenedores en el escenario con mayor probabilidad de acontecer en los próximos veinte años (2032), y también en otros escenarios que podrían presentarse en el caso de que los factores modifiquen su tendencia o bien se produzcan hechos aleatorios. El resultado se sintetiza en que la tendencia al crecimiento de los grandes buques portacontenedores en los próximos 20 años se verá condicionada por factores en relación a los conceptos de oferta (los que facilitan u obstaculizan la tendencia), demanda (los que motivan o impulsan la tendencia) y factores externos (los que desestabilizan el equilibrio entre oferta y demanda). La tendencia al crecimiento de los grandes buques portacontenedores se verá obstaculizada / limitada principalmente por factores relacionados a las infraestructuras, resultando los pasos y/o canales vinculados a las rutas marítimas, los limitantes futuros al crecimiento en dimensiones de los grandes buques portacontenedores; y la interacción buque / infraestructura (grúas) un factor que tenderá a obstaculizar esta tendencia de los grandes portacontenedores. El desarrollo económico mundial que estimula el comercio internacional y los factores precio del petróleo y condicionantes medioambientales impulsarán la tendencia al crecimiento de los grandes buques portacontenedores. Recent years have seen a sustained tendency towards the growth in the dimensions of large container ships. This has meant that port and other infrastructure used for container traffic has had to be adapted in order to provide the required services and to maintain a competitive position, so as not to lose market share. This situation implies the need for major investments in modifications to the container transport system, on account of the large volume of traffic to be handled in a short period of time. This in turn has generated a need to make provision for the probable future evolution of the ultimate dimensions that will be reached by large container ships. Such considerations give rise to the question of what are the future determinants for the growth of large container ships, requiring an overall vision of all the factors that will apply in future years, whether as a brake on or an incentive to the growth tendency which has been seen in the past and present In view of the fact that the theme to be dealt with and resolved relates to the future, with a forecasting horizon of some 20 years, a foresight methodology has been designed and applied so as to enable conclusions about probable future scenarios to be reached with a greater degree of objectivity. The designed methodology contains different methodological tools, both qualitative, semi-quantitative and quantitative, which are internally consistent. On the basis of past and present observations, the quantitative elements enable relationships to be established and forecasts to be made. Nevertheless such an approach loses validity more than three or four years into the future, on account of the very rapid and dynamic changes which may be seen at present in political, social and economic spheres. The semi-quantitative and qualitative methodologies are used coherently together and allow the analysis of past and present conditions, thus obtaining quantitative results which for short-term projections, which when integrated with the qualitative studies provide results for the long-term, facilitating the consideration of qualitative variables such as the increasing importance of environmental protection and the impact of piracy. The principal objective of the present thesis is "to identify the future conditions affecting the growth of large container ships and to determine possible scenarios". The thesis is structured in consecutive and related phases. The first three phases focus on the past and present in order to determine the problem to be resolved. The background is studied in order to establish the state of knowledge about the factors and circumstances which have motivated and facilitated the growth tendency for large container ships and the methodologies that have been used. In this way a specific foresight methodology is designed. The fourth phase, Results, is developed in distinct stages based on the previous phases, so as to resolve the problem posed and responding to the questions that arise. In this way the determined objective is reached. The fourth phase sees the application of the methodology that has been designed in order to predict posible futures. This includes analysis of the past and present factors which have caused the growth in the dimensions of large container ships up to the present. These provide the basis on which to apply the foresight methods which enable the future factors which will condition the development of such large container ships. The probable future scenarios are made up of the factors identified by expert judgement (using the Delphi technique) and validated by means of a dynamic quantitative model. This model both identifies the probable future scenarios based on past and present factors and enables the different future scenarios to be analysed as a function of future changes in the conditioning factors. Analysis of the past shows that the growth tendency up to the present for large container ships has been motivated by the growth of the world economy and the consequent increased international trade, especially between the countries of Asia with Europe and the United States. This tendency has been favoured by the trend towards globalization and by the rapid technical evolution in ship design, which has allowed the obstacles encountered to be overcome. It should be noted that even in periods of economic crisis, with an expectation for reduced trade, as experienced in recent years, the tendency towards increased ship dimensions has continued in search of economies of scale for the maritime transport of containers on transoceanic routes. The present investigation of the future evolution of large container ships has been done using a foresight methodology in which the expert judgement is validated by a dynamic quantitative methodology, founded on a firm pre-foresight analysis. The methodology that has been designed permits the evaluation, with a high degree of objectivity, of the future factors that will affect the growth of large container ships for the most probable scenario expected in the next 20 years (up to 2032). The evaluation applies also to other scenarios which may arise, in the event that their component factors are modified or indeed in the light of random events. In summary, the conclusión is that the tendency for growth in large container ships in the future 20 years will be determined by: factors related to supply, which slow or halt the tendency; factors related to demand, which encourage the tendency and finally, external factors which interrupt the equilibrium between supply and demand. The tendency for increasing growth in large container ships will be limited or even halted by factors related to infrastructure, including the natural and man-made straits and canals used by maritime transport. In addition the infrastructure required to serve such vessels both in port (including cranes and other equipment) and related transport, will tend to slow the growth tendency. The factors which will continue to encourage the tendency towards the growth of large container ships include world economic development, which stimulates international trade, and an increasing emphasis on environmental aspects.

Storabelity of melon for different ripeness stages at harvest. Selection of instrumental procedures for quality assessment.

The consumption of melon (Cucumis melo L.) has been, until several years ago, regional, seasonal and without commercial interest. Recent commercial changes and world wide transportation have changed this situation. Melons from 3 different ripeness stages at harvest and 7 cold storage periods have been analysed by destructive and non destructive tests. Chemical, physical, mechanical (non destructive impact, compression, skin puncture and Magness- Taylor) and sensory tests were carried out in order to select the best test to assess quality and to determine the optimal ripeness stage at harvest. Analysis of variance and Principal Component Analysis were performed to study the data. The mechanical properties based on non-destructive Impact and Compression can be used to monitor cold storage evolution. They can also be used at harvest to segregate the highest ripeness stage (41 days after anthesis DAA) in relation to less ripe stages (34 and 28 DAA).Only 34 and 41 DAA reach a sensory evaluation above 50 in a scale from 0-100.

Iron distribution through the developmental stages of Medicago truncatula nodules.

Paramount to symbiotic nitrogen fixation (SNF) is the synthesis of a number of metalloenzymes that use iron as a critical component of their catalytical core. Since this process is carried out by endosymbiotic rhizobia living in legume root nodules, the mechanisms involved in iron delivery to the rhizobia-containing cells are critical for SNF. In order to gain insight into iron transport to the nodule, we have used synchrotron-based X-ray fluorescence to determine the spatio-temporal distribution of this metal in nodules of the legume Medicago truncatula with hitherto unattained sensitivity and resolution. The data support a model in which iron is released from the vasculature into the apoplast of the infection/differentiation zone of the nodule (zone II). The infected cell subsequently takes up this apoplastic iron and delivers it to the symbiosome and the secretory system to synthesize ferroproteins. Upon senescence, iron is relocated to the vasculature to be reused by the shoot. These observations highlight the important role of yet to be discovered metal transporters in iron compartmentalization in the nodule and in the recovery of an essential and scarce nutrient for flowering and seed production.

Analysis of the traded volume drivers of the Iberian power futures market

A comprehensive assessment of the liquidity development in the Iberian power futures market managed by OMIP (“Operador do Mercado Ibérico de Energia, Pólo Português”) in its first 4 years of existence is performed. This market started on July 2006. A regression model tracking the evolution of the traded volumes in the continuous market is built as a function of 12 potential liquidity drivers. The only significant drivers are the traded volumes in OMIP compulsory auctions, the traded volumes in the “Over The Counter” (OTC) market, and the OTC cleared volumes in OMIP clearing house (OMIClear). Furthermore, the enrollment of financial members shows strong correlation with the traded volumes in the continuous market. OMIP liquidity is still far from the levels reached by the most mature European markets (Nord Pool and EEX). The market operator and its clearing house could develop efficient marketing actions to attract new entrants active in the spot market (energy intensive industries, suppliers, and small producers) as well as volumes from the opaque OTC market, and to improve the performance of existing illiquid products. An active dialogue with all the stakeholders (market participants, spot market operator, and supervisory authorities) will help to implement such actions.

Multiple removal of spent rocket upper stages with an ion beam shepherd

Among the many advantages of the recently proposed ion beam shepherd (IBS) debris removal technique is the capability to deal with multiple targets in a single mission. A preliminary analysis is here conducted in order to estimate the cost in terms of spacecraft mass and total mission time to remove multiple large-size upper stages of the Zenit family. Zenit-2 upper stages are clustered at 71 degrees inclination around 850 km altitude in low Earth orbit. It is found that a removal of two targets per year is feasible with a modest size spacecraft. The most favorable combinations of targets are outlined.

Cities Futures: A critical assessment of how future studies are applied to cities

Análisis critic de la aplicación de los estudios de future al campo de la planificación urbana

Effect of cage type on the behaviour pattern of rabbit does at different physiological stages

Interest in commercially farmed rabbit welfare has increased in recent years. As a result, new alternative housing systems have been developed, although they require evaluation in order to demonstrate their potential for improving welfare. The aim of this trial was to study the behavioural traits of rabbit does housed in 2 different types of cage (TC): conventional vs. alternative with an elevated platform, at different physiological stages (PS); lactation and gestation. Behavioural observations were carried out on 12 rabbit commercial does using continuous 24 h video recording. Independently of PS and TC, rabbit does spent most of their time on foot mats (on av. 57.7%). However, due to the use of platforms (on av. 23.0% of time), lactating does spent 36.6% less time on foot mats (P<0.001) and gestating does spent 27.0% less time on wire mesh (P<0.001) in alternative cages than in conventional cages. Alternative cages allowed for standing posture, but this behaviour was only observed in gestating does (on av. 4.6 times a day). Frequency of drinking was higher in conventional than in alternative cages (24.6 vs. 19.1 times a day; P<0.05). Gestating does housed in conventional cages reached the highest duration and frequency of interacting with neighbours (276 s/d and 4.6 times/d; P<0.05). The frequency of interacting with kits was lower in alternative than in conventional cages (2.4 vs. 8.6 times a day; P<0.01). Doe behaviour was influenced by the time of day, with less activity during the midday hours. During dark hours, rabbit does more frequently performed restless behaviour such as hyperactivity or nursing, matching the time at which rabbit does spent more time on the platform. The platform was frequently used by rabbit does, regardless of their physiological stage, and during late lactation phase, when mothers were not receptive to nursing, does housed in alternative cages used the platform as a mean to flee from kits trying to suckle. Use of the platform might lead to hygienic problems due to retained faeces on the platform and faeces and urine falling onto animals located in the lower part of the cage. The absence of stereotypies in rabbit does of this trial, suggested that animal welfare was not compromised by the type of housing (conventional or alternative cages).

Extralimital Senegalese species during Marine Isotope Stages 5.5 and 11 in the Canary Islands (29° N): Sea surface temperature estimates

The presence of Harpa doris Röding, 1798 in marine deposits of the last interglacial period, ~130-120 ka (marine isotope stage or MIS 5.5) in the Canary Islands (Gran Canaria, Lanzarote and Fuerteventura) enabled us to compare this occurrence with its present habitat in the Gulf of Guinea and the Cape Verde Islands, well to the south. This comparison leads to the conclusion that sea surface temperatures (SSTs) in the waters around the Canary Islands during the last interglacial period were at least 3.3 °C higher than today. H. doris is found in association with the large gastropod Persististrombus latus (Gmelin, 1791) as well as the coral Siderastrea radians (Pallas, 1766). The presence of these extralimital southern,warm-water species in the Canary Islands during the last interglacial period also implies a northward expansion of plankton-feeding larvae in seawater with a high chlorophyll-a content. Such conditionswould require a shortening of the southern arm of the cool Canary Current that dominates the waters around the Canary Islands at present. Marine deposits dating to ~400 ka (MIS 11) are also found on the Canary Islands. In these deposits, the presence of Saccostrea cucullata (Born, 1778) allows a comparison with its present habitat in the Gulf of Guinea. In this analysis, we conclude that SSTs in waters around the Canary Islands during this major interglacial period were at least 4.2 °C higher than today. Middle Pleistocene fossils of S. cucullata have also been found in the western Mediterranean Sea and Morocco, as well as the Cape Verde Islands. If these deposits also date to MIS 11, SST warming could have been a regional phenomenon, including much of the eastern Atlantic Ocean and Mediterranean Sea.

Comportamiento térmico y mecánico del yeso con adiciones de aerogel de sílice granulado

La presente tesis doctoral aborda el estudio de un nuevo material mineral, compuesto principalmente por una matriz de yeso (proveniente de un conglomerante industrial basado en sulfato de calcio multifase) y partículas de aerogel de sílice hidrófugo mesoporoso, compatibilizadas mediante un surfactante polimérico, debido a su alto carácter hidrófugo. La investigación se centra en conocer los factores que influyen en las propiedades mecánicas y conductividad térmica del material compuesto generado. Este estudio pretende contribuir al conocimiento sobre el desarrollo de nuevos morteros de elevado aislamiento térmico que puedan ser utilizados en la rehabilitación energética de edificios de viviendas existentes, debido a que estos representan gran parte del consumo energético del parque de viviendas de España, aunque también a nivel internacional. De los materiales utilizados para desarrollar los morteros estudiados, el yeso, además de ser un material muy abundante, especialmente en España, requiere una menor cantidad de energía para la fabricación de un conglomerante (debido a una menor temperatura de fabricación), en comparación con el cemento o la cal, por lo que presenta una menor huella de carbono que estos últimos. Por otro lado, el aerogel de sílice hidrófugo mesoporoso es, de acuerdo con la documentación disponible, el material que posee actualmente la mayor capacidad de aislamiento térmico en el mercado. El desarrollo de nuevos morteros minerales con una capacidad de aislamiento térmico mayor que los materiales aislantes utilizados tradicionalmente, tiene una aplicación relevante en los casos de rehabilitación energética de edificios históricos y patrimoniales, en los que se requiere la aplicación del aislamiento por el interior de la fachada, ya que este tipo de soluciones tienen el inconveniente de reducir el espacio habitable de las áreas involucradas, especialmente en zonas climáticas en las que el aislamiento térmico puede suponer un espesor considerable, por lo que es ideal utilizar materiales de altas prestaciones de aislamiento térmico capaces de aportar el mismo nivel de aislamiento (o incluso mayor), pero en un espesor considerablemente menor. La investigación se desarrolla en tres etapas: bibliográfica, experimental y de simulación. La primera etapa, parte del estudio de la bibliografía existente, relacionada con materiales aislantes, incluyendo soluciones basadas, tanto en morteros aislantes, como en paneles de aislamiento térmico. La segunda, de carácter experimental, se centra en estudiar la influencia de la microestrucrura y macroestructura, del nuevo material mineral, en las propiedades físicas elementales, mecánicas y conductividad térmica del compuesto. La tercera etapa, mediante una simulación del consumo energético, consiste en cuantificar teóricamente el potencial ahorro energético que puede aportar este material en un caso de rehabilitación energética en particular. La investigación experimental se centró principalmente en conocer los factores principales que influyen en las propiedades mecánicas y conductividad térmica de los materiales compuestos minerales desarrollados en esta tesis. Para ello, se llevó a cabo una caracterización de los materiales de estudio, así como el desarrollo de distintas muestras de ensayo, de tal forma que se pudo estudiar, tanto la hidratación del yeso en los compuestos, como su posterior microestructura y macroestructura, aspectos fundamentales para el entendimiento de las propiedades mecánicas y conductividad térmica del compuesto aislante. De este modo, se pudieron conocer y cuantificar, los factores que influyen en las propiedades estudiadas, aportando una base de conocimiento y entendimiento de este tipo de compuestos minerales con aerogel de sílice hidrófugo, no existiendo estudios publicados hasta el momento de finalización de esta tesis, con la aproximación al material propuesta en este estudio, ni con yeso (basado en sulfato de calcio multifase), ni con otro tipo de conglomerantes. Particularmente, se determinó la influencia que tiene la incorporación de partículas de aerogel de sílice hidrófugo, en grandes proporciones en volumen, en un compuesto mineral basado en distintas fases de sulfato de calcio. No obstante, para llevar a cabo las mezclas, fue necesario utilizar un surfactante para compatibilizar este tipo de partículas, con el conglomerante basado en agua. El uso de este tipo de aditivos tiene una influencia, no solo en el aerogel, sino en las propiedades del compuesto en general, dependiendo de su concentración, por lo que se establecieron dos porcentajes de adición: la primera, determinada a partir de la cantidad mínima necesaria para compatibilizar las mezclas (0,1% del agua de amasado), y la segunda, como límite superior, la concentración utilizada habitualmente a nivel industrial para estabilizar burbujas de aire en hormigones espumados (5%). El surfactante utilizado mostró la capacidad de modificar la superficie del aerogel, cambiando el comportamiento de las partículas frente al agua, permitiendo una invasión parcial de su estructura porosa, por parte del agua de amasado. Este comportamiento supone un aumento muy importante en la relación agua/yeso, afectando el hábito cristalino e influenciando negativamente las propiedades mecánicas de la matriz de yeso, presentando un efecto aún notable a mayor concentración de surfactante (5%). En cuanto a las propiedades finales alcanzadas, fue posible lograr un compuesto mineral ultraligero (200 kg/m3), con alrededor de un 60% de aerogel en volumen y de alta capacidad aislante (0,028 W/m•K), presentando una conductividad térmica notablemente menor que los morteros aislantes del mercado, e incluso también menor que la de los aislantes tradicionales basado en las lanas minerales o EPS; no obstante, con la limitante de presentar bajas propiedades mecánicas, condicionando su posible aplicación futura. Entre los factores principales relacionados con las propiedades mecánicas, se encontró que estas dependen exponencialmente del volumen de yeso en el compuesto; no obstante, factores de segundo orden, como el grado de hidratación, o una mejor distribución del conglomerante entre las partículas de aerogel, debido al aumento de la superficie específica del polvo mineral, pueden aumentar las propiedades mecánicas entre el doble y el triple, dependiendo del volumen de aerogel en cuestión. Además, se encontró que el aerogel, en conjunto con el surfactante, es capaz de introducir una gran cantidad de aire (0,70 m3 por cada m3 de aerogel), que unido al agua evaporada (no consumida por el conglomerante durante la hidratación), el volumen de aire total alcanza, generalmente, un 40%, independientemente de la cantidad de aerogel en la mezcla. De este modo, el aire introducido en la matriz desplaza las proporciones en volumen del aerogel y del yeso, disminuyendo, tanto las propiedades mecánicas, como la capacidad aislante de compuesto mineral. Por otro lado, la conductividad térmica mostró tener una dependencia directa de la contribución de las tres fases principales en el compuesto: yeso, aerogel y aire ocluido. De este modo, se pudo desarrollar un modelo matemático, adaptado de uno existente, capaz de calcular, con bastante precisión, la relación de los tres componentes mencionados, en la conductividad térmica de los compuestos, para el rango de volúmenes y materiales utilizados en esta tesis. Finalmente, la simulación del consumo energético realizada a una vivienda típica de España, de los años 1900 a 1959 (basada en muros de ladrillo macizo), para las zonas climáticas estudiadas (A, D y E), permitió observar el potencial ahorro energético que puede aportar este material, dependiendo de su espesor, como aislamiento interior de los muros de fachada. Particularmente, para la zona A, se determinó un espesor óptimo de 1 cm, mientras que para la zona D y E, 3,5 y 3,9 cm respectivamente. En este sentido, el nuevo material estudiado es capaz de disminuir, entre un 35% y un 80%, el espesor de la capa aislante, en comparación con paneles de lana de roca o los morteros minerales de mayor capacidad aislante del mercado español respectivamente. ABSTRACT The present doctoral thesis studies a new mineral-based composite material, composed by a gypsum matrix (based on an industrial multiphase gypsum binder) and mesoporous hydrophobic silica aerogel particles, compatibilized with a polymeric surfactant due to the high hydrophobic character of the insulating particles. This study pretends to contribute to the development of new composite insulating materials that could be used in energy renovation of existing dwellings, in order to reduce their high energy consumption, as they represent a great part of the total energy consumed in Spain, but also internationally. Between the materials used to develop de studied insulating mortars, gypsum, besides being an abundant material, especially in Spain, requires less energy for the manufacture of a mineral binder (due to lower manufacturing temperatures), compared to lime or cement, thus presenting lower carbon footprint. In other hand, the hydrophobic mesoporous silica aerogel, is, according to the existing references, the material with the highest know insulating capacity in the market. The development of new mineral mortars with higher thermal insulation capacity than traditional insulating materials, presents a relevant application in energy retrofitting of historic and cultural heritage buildings, in which implies that the insulating material should be installed as an internal layer, rather than as an external insulating system. This type of solution involves a reduced internal useful area, especially in climatic zones where the demand for thermal insulation is higher, and so the insulating layer thickness, being idealistic to use materials with very high insulating properties, in order to reach same insulating level (or higher), but in lower thickness than the provided by traditional insulating materials. This research is developed in three main stages: bibliographic, experimental and simulation. The first stage starts by studying the existing references regarding thermally insulating materials, including existing insulating mortars and insulating panels. The second stage, mainly experimental, is centered in the study of the the influence of the microstructure and macrostructure in the physical and mechanical properties, and also in the thermal conductivity of the new mineral-based material. The thirds stage, through energy simulation, consists in theoretically quantifying the energy savings potential that can provide this type of insulating material, in a particular energy retrofitting case study. The experimental research is mainly focused in the study of the factors that influence the mechanical properties and the thermal conductivity of the thermal insulating mineral composites developed in this thesis. For this, the characterization of the studied materials has been performed, as well as the development of several experimental samples, in order to study the hydration of the mineral binder within the composites, but also the final microstructure and macrostructure, fundamental aspects for the understanding of the composite’s mechanical and insulating properties. Thus, is was possible to determine and quantify the factors that influence the studied material properties, providing a knowledge base and understanding of mineral composites that comprises mesoporous hydrophobic silica aerogel particles, being the first study up to date regarding the specific approach of the present study, regarding not just multiphase calcium sulfate plaster, but also other mineral binders. Particularly, the influence of the incorporation of hydrophobic silica aerogel particles, in high volume ratios into a mineral compound, based on different phases of calcium sulfate has been determined. However, to perform mixing, it is necessary to use a surfactant in order to compatibilize these particles with the water-based mineral binder. The use of such additives has an influence, not only in the aerogel, but the overall properties of the compound, so two different surfactant concentration has been studied: the first, the minimum amount of surfactant (used in this thesis) in order to develop the slurries (0.1% concentration of the mixing water), and the second, as the upper limit, the concentration usually used industrially to stabilize air bubbles in foamed concrete (5%). One of the side effects of using such additive, was the modification of the aerogel particles, by changing their behavior in respect to water, generating a partial invasion of the aerogel’s porous structure, by the mixing water. This behavior produces a very important increase in water/binder ratios, affecting the crystal habit and negatively influencing the mechanical properties of the gypsum matrix. This effect further increased when a higher concentration of surfactant (5%) is used. Regarding final materials properties, it was possible to achieve an ultra-lightweight mineral composite (200 kg/m3), with around 60% by volume of aerogel, presenting a very high insulating capacity (0.028 W/m•K), a noticeable lower thermal conductivity compared to the insulating mortars and traditional thermal insulating panels on the market, such as mineral wool or EPS; however, the limiting factor for future’s material application in buildings, is related to the very low mechanical properties achieved. Among the main factors related to the mechanical properties, it has been found an exponential correlation to the volume of gypsum in the composite. However, second-order factors such as the degree of hydration, or a better distribution of the binder between the aerogel particles, due to the increased surface area of the mineral powder, can increase the mechanical properties between two to three times, depending aerogel volume involved. In addition, it was found that the aerogel, together with the surfactant, is able to entrain a large amount of air volume (around 0.70 m3 per m3 of aerogel), which together with the evaporated water (not consumed by the binder during hydration), can reach generally around 40% of entrained air within the gypsum matrix, regardless of the amount of aerogel in the mixture. Thus, the entrained air into the matrix displaces the volume proportions of the aerogel and gypsum, reducing both mechanical and insulating properties of the mineral composite. On the other hand, it has been observed a direct contribution of three main phases into the thermal conductivity of the composite: gypsum, aerogel and entrained air. Thus, it was possible to develop a mathematical model (adapted from an existing one), capable of calculating quite accurate the thermal conductivity of such mineral composites, from the ratio these three components and for the range of volumes and materials used in this thesis. Finally, the energy simulation performed to a typical Spanish dwelling, from the years 1900 to 1959 (mainly constructed with massive clay bricks), within three climatic zones of Spain (A, D and E), showed the energy savings potential that can provide this type of insulating material, depending on the thickness of the applied layer. Particularly, for the climatic A zone, it has been found an optimal layer thickness of 1 cm, while for zone D and E, 3.5 and 3.9 cm respectively. In this manner, the new studied materials is capable of decreasing the thickness of the insulating layer by 35% and 80%, compared with rock wool panels or mineral mortars with the highest insulating performance of the Spanish market respectively.