Effect of the cooling rate on microstructure and hardness of MAR-M247 Ni-based superalloy

The effect of cooling rate on the microstructure of MAR-M247 Ni-based superalloy was investigated via physical simulation of the casting process. Solidification experiments with cooling rates in the range of 0.25–10 K/s showed smooth temperature profiles with measured cooling rates matching the set values. The MAR-M247 showed cellular (0.25 K/s) and dendritic (1, 5 and 10 K/s) microstructures. Microconstituents also varied with cooling rates: γ/γ′ matrix with carbides and γ/γ′ eutectic at 0.25 K/s, γ/γ′ matrix with carbides at 1 K/s, and γ/γ′ matrix with carbides and γ/MC eutectic at 5 and 10 K/s. Moreover, the secondary dendritic arm spacing decreased and the hardness increased with the increase in the cooling rates.

Effect of the Synthesis Route on the Microstructure and the Dielectric Behavior of CaCu3Ti4O12 Ceramics

CaCu3Ti4O12 (CCTO) was prepared by a conventional synthesis (CS) and through reaction sintering, in which synthesis and sintering of the material take place in one single step. The microstructure and the dielectric properties of CCTO have been studied by XRD, FE-SEM, EDS, AFM, and impedance spectroscopy to correlate structure, microstructure, and electrical properties. Samples prepared by reactive sintering show very similar dielectric behavior to those prepared by CS. Therefore, it is possible to prepare CCTO by means of a single-step processing method.

Effect of the Reference Line on Main Roughness Parameters

In the present paper the influence of the reference system with regard to the characterization of the surface finishing is analyzed. The effect of the reference system’s choice on the most representative surface finishing parameters (e.g. roughness average Ra and root mean square values Rq) is studied. The study can also be applied to their equivalent parameters in waviness and primary profiles. Based on ISO and ASME standards, three different types of regression lines (center, mean and orthogonal) are theoretically and experimentally analyzed, identifying the validity and applicability fields of each one depending on profile’s geometry.

The counteractive effect of the sensor housing on the unit sensitivity across a series of dynamic temperature profiles.

The advantages of wireless sensing implemented on the cold chain of fresh products are well known. These sensor systems consist of a combination of delicate internal electronic circuitry enclosed in a special housing unit. Manufacturers however are presented with the challenge that the housing required to withstand the harsh environment in which the sensors are being used all too often take from the functionality of the sensor. Therefore the target of this study is to determine the dynamic behavior and the counteractive effects of the sensor housing on temperature recording accuracy in the wireless nodes of Wireless Sensor Network (WSN) and Radio Frequency Identification (RFID) semi-passive tags. Two kind of semi-passive Turbo Tags were used (T700 and T702-B), which consisted of sensors with and without a cover, and two kind of WSN nodes, IRIS (sensors Intersema and Sensirion soldered in the motherboard) and NLAZA (Sensirion in a cable and soldered to the motherboard). To recreate the temperature profiles the devices were rotated between a cold room(5 ºC) through a ambient room(23 ºC) to a heated environment (35ºC) and vice versa. Analysis revealed the differences between housing and no housing are 308.22s to 21.99s respectively in the step from 5 to 35 ºC. As is demonstrated in these experiments the influence of the housing significantly hinders sensor accuracy.

Effect of the pulse trajectory on ultrasonic fluid velocity measurement

In a general situation a non-uniform velocity field gives rise to a shift of the otherwise straight acoustic pulse trajectory between the transmitter and receiver transducers of a sonic anemometer. The aim of this paper is to determine the effects of trajectory shifts on the velocity as measured by the sonic anemometer. This determination has been accomplished by developing a mathematical model of the measuring process carried out by sonic anemometers; a model which includes the non-straight trajectory effect. The problem is solved by small perturbation techniques, based on the relevant small parameter of the problem, the Mach number of the reference flow, M. As part of the solution, a general analytical expression for the deviations of the computed measured speed from the nominal speed has been obtained. The correction terms of both the transit time and of the measured speed are of M 2 order in rotational velocity field. The method has been applied to three simple, paradigmatic flows: one-directional horizontal and vertical shear flows, and mixed with a uniform horizontal flow.

Object Kinetic Monte Carlo calculations of irradiated Fe-Cr dilute alloys: The effect of the interaction radius between substitutional Cr and self-interstitial Fe

ObjectKineticMonteCarlo models allow for the study of the evolution of the damage created by irradiation to time scales that are comparable to those achieved experimentally. Therefore, the essential ObjectKineticMonteCarlo parameters can be validated through comparison with experiments. However, this validation is not trivial since a large number of parameters is necessary, including migration energies of point defects and their clusters, binding energies of point defects in clusters, as well as the interactionradii. This is particularly cumbersome when describing an alloy, such as the Fe–Cr system, which is of interest for fusion energy applications. In this work we describe an ObjectKineticMonteCarlo model for Fe–Cr alloys in the dilute limit. The parameters used in the model come either from density functional theory calculations or from empirical interatomic potentials. This model is used to reproduce isochronal resistivity recovery experiments of electron irradiateddiluteFe–Cr alloys performed by Abe and Kuramoto. The comparison between the calculated results and the experiments reveal that an important parameter is the capture radius between substitutionalCr and self-interstitialFe atoms. A parametric study is presented on the effect of the capture radius on the simulated recovery curves.

Transportation infrastructure impacts on firm location: the effect of a new metro line in the suburbs of Madrid

Firm location patterns emerge as a consequence of multiple factors, including firm considerations, labor force availability, market opportunities, and transportation costs. Many of these factors are influenced by changes in accessibility wrought by new transportation infrastructure. In this paper we use spatial statistical techniques and a micro-level data base to evaluate the effects of Madrid?s metro line 12 (known as Metrosur) expansion on business location patterns. The case study is the municipality of Alcorcon, which is served by the new metro line since 2003. Specifically, we explore the location patterns by different industry sectors, to evaluate if the new metro line has encouraged the emergence of a ?Metrosur spatial economy?. Our results indicate that the pattern of economic activity location is related to urban accessibility and that agglomeration, through economies of scale, also plays an important role. The results presented in this paper provide evidence useful to inform efficient transportation, urban, and regional economic planning.

Effect of the oxygen isoelectronic substitution in Cu2ZnSnS4 and its photovoltaic application

The optoelectronic properties of Cu2ZnSnS4 and environmental considerations have attracted significant interest for photovoltaics. Using first-principles, we analyze the possible improvement of this material as a photovoltaic absorber via the isoelectronic substitution of S with O atoms. The evolution of the acceptor level is analyzed with respect to the atomic position of the nearest neighbors of the O atom. We estimate the maximum efficiency of this compound when used as a light absorber. The presence of the sub-band gap level below the conduction band could increases the solar-energy conversion with respect to the host.

Effect of the application of jasmonic acid and benzoic acid on grafted watermelons yield under greenhouse conditions in the southeast of Spain for mitigation of stress

One of the main problems of watermelon crops in Sou theast Spain is the thermal difference because of c limatic conditions that appear during the first stages of the crop. The objective of this work was to evaluate the effect of inducing the systemic acq uired resistance (SAR) and the induced systemic resistance (ISR) through the application of jasmonic ac id (JA) and benzoic acid (BA), respectively, to counter the abiotic stress. We assessed two treatments of JA and BA, T1 (500 mg·kg-1 + 500 mg·kg -1 ) and T 2 (2000 mg·kg -1 + 2000 mg·kg -1), as well as a control test using an experimental design of randomized blocks with four replications. The results obtained for kg·m -2, fruits/m², kg/plant and fruits/plant did not show statistically significant differences. However, we obtained statistically sig nificant differences in the average fruit weight co mpared with the control test in the two experiments carried out in 2009 and 2010. The results showed that there was no metabolic cost in the plants when applying the assessed treatments of JA and BA.

Effect of Stress Level on the High Temperature Deformation and Fracture Mechanisms of Ti-45Al-2Nb-2Mn-0.8 vol. pct TiB2: An In Situ Experimental Study

The effect of the applied stress on the deformation and crack nucleation and propagation mechanisms of a c-TiAl intermetallic alloy (Ti-45Al-2Nb-2Mn (at. pct)-0.8 vol. pct TiB2) was examined by means of in situ tensile (constant strain rate) and tensile-creep (constant load) experiments performed at 973 K (700 �C) using a scanning electron microscope. Colony boundary cracking developed during the secondary stage in creep tests at 300 and 400 MPa and during the tertiary stage of the creep tests performed at higher stresses. Colony boundary cracking was also observed in the constant strain rate tensile test. Interlamellar ledges were only found during the tensile-creep tests at high stresses (r>400 MPa) and during the constant strain rate tensile test. Quantitative measurements of the nature of the crack propagation path along secondary cracks and along the primary crack indicated that colony boundaries were preferential sites for crack propagation under all the conditions investigated. The frequency of interlamellar cracking increased with stress, but this fracture mechanism was always of secondary importance. Translamellar cracking was only observed along the primary crack.

Soil moisture content determines the effect of the urease inhibitor NBPT on N2O emissions

Among the mitigation strategies to prevent nitrogen (N) losses from ureic fertilizers, urease inhibitors (UIs) have been demonstrated to promote high N use efficiency by reducing ammonia (NH3) volatilization. In the last few years, some field experiments have also shown its effectiveness in reducing nitrous oxide (N2O) losses from fertilized soils under conditions of low soil moisture. An incubation experiment was carried out with the aim of assessing the main biotic mechanisms behind N2O emissions once that the UIs N-(n-butyl) thiophosphoric triamid (NBPT) and phenil phosphorodiamidate (PPDA) were applied with Urea (U) under different soil moisture conditions (40, 60 and 80 % water-filled pore space, WFPS). In the same study we tried to analyze to what extent soil WFPS regulates the effect of these inhibitors on N2O emissions. The use of PPDA in our study allowed us to compare the effect of NBPT with that of another commercially available urease inhibitor, aiming to see if the results were inhibitor-specific or not. Based on the results from this experiment, a WFPS (i.e. 60 %) was chosen for a second study (i.e. mesocosm experiment) aiming to assess the efficiency of the UIs to indirectly affect N2O emissions through influencing the pool of soil mineral N. The N2O emissions at 40 % WFPS were almost negligible, being significantly lower from all fertilized treatments than that produced at 60 and 80 % WFPS. When compared to U alone, NBPT+U reduced the N2O emissions at 60 % WFPS but had no effect at 80 % WFPS. The application of PPDA significantly increased the emissions with respect to U at 80 % WFPS whereas no significant effect was found at 60 %. At 80 % WFPS, denitrification was the main source of N2O emissions for all treatments. In the mesocosm study, the application of NBPT+U was an effective strategy to reduce N2O emissions (75 % reduction compared to U alone), due to a lower soil ammonium (NH4 +) content induced by the inhibitor. These results suggest that adequate management of the UI NBPT could provide, under certain soil conditions, an opportunity for mitigation of N2O emissions from fertilized soils.

Identification of the method to quantify soluble fibre and the effect of the source of fibre on the ileal and faecal digestibility of soluble and insoluble fibre in rabbits = Identificación del método para cuantificar la fibra soluble y el efecto de la fuente de fibra en la digestibilidad ileal y fecal de la fibra soluble e insoluble en conejos

La presente tesis constituye un avance en el estudio de los métodos para cuantificar la fibra soluble y los efectos de las fracciones de fibra y las fuentes de fibra sobre la digestión de las diferentes fracciones de fibra (soluble e insoluble) en el conejo. Hay un efecto positivo de la fibra soluble sobre la salud intestinal de los conejos y, por ende, una reducción de la mortalidad en animales destetados. Pese a esto, no está claro si estos efectos se deben específicamente a la fracción soluble. Por lo que los objetivos generales de esta tesis fueron: 1) comparar diferentes metodologías químicas e in vitro para cuantificar la fibra soluble y estudiar las posibles interferencias en la cuantificación de la fibra soluble por las mucinas, y viceversa, 2) determinar los efectos de la fibra, el lugar de fermentación, el método para valorar la fibra soluble e insoluble, y la corrección de la fibra soluble por el contenido intestinal de mucinas sobre la digestibilidad de las distintas fracciones de la fibra y 3) evaluar los efectos individuales de las fracciones soluble e insoluble de la fibra de pulpa de remolacha y de manzana, sobre la digestibilidad de la fibra soluble e insoluble y los parámetros digestivos. Para ello se llevaron a cabo 4 estudios. En el primer estudio se compararon diferentes metodologías químicas e in vitro para valorar la fibra soluble de diferentes alimentos y se estudió la posible interferencia en la determinación de la fibra soluble y mucinas. Para ello se utilizaron seis ingredientes (pulpa de remolacha, pectinas de pulpa de remolacha, pulpa de remolacha lavada, paja de cereal, cascarilla de girasol y lignocelulosa) y siete piensos de conejos con diferentes niveles de fibra soluble. En un primer experimento se analizó la fibra dietética total (FDT), la fibra dietética insoluble (FDI), la fibra dietética soluble (FDS), la fibra neutro detergente corregida por cenizas y proteínas (aFNDmo-pb), y la digestibilidad in vitro 2 pasos pepsina/pancreatina (residuo corregido por cenizas y proteína, ivMSi2) de los ingredientes y piensos. Además la fibra soluble se calculó mediante la diferencia entre FDT-FDI (FDSFDI), FDT- ivMSi2 (FDSivMSi2), y FDT - aFNDmo-pb (FDSaFNDmo-pb). Cuando la fibra soluble se determinó directamente como FDS o se calculó como FDT-FDI no se observaron diferencias (109 g/kg MS, en promedio). Sin embargo, cuando la fibra soluble se calculó como FDT - aFNDmo-pb su valor fue un 40% menor (153 g/kg MS. P < 0,05), mientras que la FDSFDI (124 g/kg MS) no fue diferente a ninguna de las otras metodologías. La correlación entre los tres métodos fue elevada (r > 0,96. P < 0,001. n = 13), pero disminuyó o incluso desapareció cuando la pulpa o las pectinas de la remolacha fueron excluidas del análisis. En un segundo experimento, se comparó el método ivDMi2 usando crisoles (método de referencia) con una modificación del mismo usando bolsas ANKOM digeridas individualmente o en colectivo para simplificar la determinación de la FDSivMSi2. La FDSivMSi2 no difirió entre los métodos comparados. En un tercer experimento, se analizó la posible interferencia entre la determinación de la fibra soluble y las mucinas intestinales. Se observó un contenido de FDT y de mucinas elevado en las muestras de pectinas de remolacha (994 y 709 g/kg MS), así como en el moco intestinal de conejo (571 y 739 g/kg MS) cuando se aplicó el método de mucinas por precipitación con etanol. Sin embargo, después de aplicar una pectinasa en el material precipitado, la cantidad de mucinas recuperadas en las muestras de pectinas de remolacha fue cercana a cero, mientras que en el moco intestinal fue similar a los resultados previos al uso de la enzima. Con los resultados de este ensayo se estimaron los carbohidratos de mucinas retenidos en los contenidos digestivos y se propuso una corrección para la determinación de la digestibilidad de la FDT y fibra soluble. En conclusión, la contaminación de las mucinas de la digesta con fibra soluble se soluciona usando pectinasas. El segundo estudio se centró en estudiar: 1) el efecto del tipo de fibra, 2) el sitio de fermentación, 3) el método para cuantificar fibra y 4) la corrección por mucinas sobre la digestibilidad de la fibra. Para ello se formularon tres piensos con diferentes niveles de fibra soluble (FDT-aFNDmo-pb). Un pienso bajo en fibra soluble (LSF. 85 g/kg DM), un pienso medio en fibra soluble (MSF. 102 g/kg DM), y un pienso alto en fibra soluble (HSF. 145 g/kg DM). Estos piensos se obtuvieron reemplazando un 50% del heno del alfalfa en el pienso MSF por una mezcla de pulpa de manzana y remolacha (HSF) o por una mezcla de cascarilla de avena y proteína de soja (LSF). Se utilizaron 30 conejas canuladas para determinar la digestibilidad ileal y fecal. La digestibilidad cecal se calculó mediante diferencia entre la digestibilidad fecal e ileal. La fibra insoluble se determinó como aFNDmo-pb, IDF, e ivMSi2, mientras que la fibra soluble se calculó como FDSFDI, FDSaFNDmo-pb, y FDSivMSi2. La digestibilidad de la FDT y la fibra soluble se corrigieron por las mucinas. La concentración de mucinas en la digesta ileal y fecal, aumento desde el grupo LSF hasta el grupo con el pienso HSF (P < 0,01). La corrección por mucinas aumentó las digestibilidades de la FDT y la fibra soluble a nivel ileal, mientras que a nivel cecal las redujo. (P < 0.01). El coeficiente de digestibilidad ileal de FDT aumentó desde el grupo LSF al grupo HSF (0,12 vs. 0,281. P < 0,01), sin diferencias en el coeficiente de digestibilidad cecal (0,264), por lo que la tendencia a nivel fecal entre los grupos se mantuvo. El coeficiente de digestibilidad ileal de la fibra insoluble aumento desde el grupo con el pienso LSF al grupo con el pienso HSF (0,113 vs. 0,210. P < 0,01), sin diferencias a nivel cecal (0,139) y sin efecto del método usado, resultando en una digestibilidad elevada a nivel fecal, con tendencias similares a las observadas a nivel ileal. El coeficiente de digestibilidad de la FND fue elevada en comparación con la FDI o la ivMSi2 (P > 0.01). El coeficiente de la digestibilidad ileal de la fibra soluble fue mayor en el grupo LSF respecto al grupo LSF (0,436 vs. 0,145. P < 0,01) y el método no afectó a esta determinación. El coeficiente de la digestibilidad cecal de la fibra soluble se redujo desde el grupo LSF hasta el grupo HSF (0,721 vs. 0,492. P < 0,05). El valor más bajo de digestibilidad cecal y fecal de fibra soluble fue medido con el método FDSaFNDmo-pb (P < 0,01). Se observó una alta correlación entre las digestibilidades de la fibra soluble determinada como FDSFDI, FDSaFNDmo-pb, y FDSivMSi2, por lo tanto la información proporcionada por una u otra metodología fueron similares. Sin embargo, cuando se compararon con efectos fisiológicos (producción de mucinas y peso del ciego y pH del ciego de un trabajo previo), la FDSaFNDmo-pb globalmente mostró estar mejor correlacionado con estos parámetros fisiológicos. En conclusión, la corrección por mucinas es necesaria para determinar la digestibilidad ileal de la FDT y fibra soluble, mientras que la elección de uno u otro método es menos relevante. La inclusión de pulpa de manzana y remolacha incrementa la cantidad de FDT que desaparece antes de llegar al ciego. En el tercer estudio se estudió el efecto de la fracción fibrosa soluble e insoluble de la pulpa de remolacha y el método de cuantificación de la fibra soluble e insoluble sobre la digestibilidad de la fibra y algunos parámetros digestivos. Para ello se formularon cuatro piensos con niveles similares de fibra insoluble (315g aFNDmo-pb/kg MS) y proteína (167 g/kg MS). El pienso control contuvo el nivel más bajo de fibra soluble (30,3 g/kg, con cascarilla de girasol y paja como fuente de fibra). Un segundo pienso se obtuvo mediante la sustitución de 60 g de almidón/kg del pienso control por pectinas de remolacha (82,9 g fibra soluble/kg MS). Los otras dos piensos resultaron de la sustitución parcial de las fuentes de fibra del pienso control por la fracción insoluble de la pulpa de remolacha y la pulpa de remolacha entera (42.2 y 82.3 g fibra soluble/kg MS, respectivamente). Cincuenta y seis conejos en cebo (14/pienso), de 2,4  0.21 kg de peso, fueron usados para determinar la digestibilidad ileal y fecal de la FDT, FDI, aFNDmo-pb, FDSFDI, y FDSaFNDmo-pb. La concentración de mucinas en el íleon y heces se utilizaron para corregir la digestibilidad de la FDT y fibra soluble. También se midió el peso de diferentes segmentos del tracto digestivo y el pH del contenido digestivo. Los conejos alimentados con el pienso de fibra insoluble de pulpa de remolacha mostraron los consumos más bajos con respecto a los demás grupos (124 vs. 139 g/d, respectivamente. P < 0,05). El flujo de mucinas ileales fue más alto (P < 0.05) en el grupo alimentado con el pienso de pectinas de remolacha (9,0 g/d en promedio) que los del grupo control (4,79 g/d), mostrando los otros dos grupos valores intermedios, sin detectarse diferencias a nivel fecal. La digestibilidad ileal de la FDT (corregida por mucinas) y la fibra insoluble no se vieron afectadas por el tipo de pienso. El método usado para determinar la fibra insoluble afectó su digestibilidad ileal (0,123 para FDI vs. 0,108 para aFNDmo-pb. P < 0.01). De todas formas, los métodos no afectaron al cálculo de la fibra fermentada antes del ciego (4,9 g/d en promedio). Los conejos alimentados con el pienso de pulpa de remolacha y con el pienso con la fracción insoluble de la pulpa de remolacha mostraron las digestibilidades fecales más altas de la fibra insoluble (0,266 en promedio vs. 0,106 del grupo control), mientras que en los animales del pienso con pectinas esta digestibilidad fue un 47% mayor respecto al pienso control (P < 0,001). La digestibilidad fecal de la fibra insoluble fue un 20% más alta cuando se usó la FND en lugar de FDI para determinarla (P < 0.001). Esto hizo variar la cantidad de fibra insoluble fermentada a lo largo del tracto digestivo (9,5 ó 7,5 g/d cuando fue calculada como FDI o aFNDmo-pb, respectivamente. P < 0,001). Las digestibilidades ileales de la fibra soluble fueron positivas cuando los análisis de fibra soluble de los contenidos ileales fueron corregidos por mucinas, (P < 0,001) excepto para la digestibilidad ileal de la FDSIDF del grupo control. Una vez corregidas por mucinas, los conejos alimentados con los piensos que contuvieron la fracción soluble de la pulpa de remolacha (pienso de pectina y pulpa de remolacha) mostraron una mayor digestibilidad ileal de la fibra soluble, respecto al grupo control (0,483 vs. -0,010. P = 0.002), mientras que el grupo del pienso de fibra insoluble de pulpa de remolacha mostró un valor intermedio (0,274). La digestibilidad total de la fibra soluble fue similar entre todos los grupos (0.93). Los conejos alimentados con pulpa de remolacha y su fracción insoluble mostraron los pesos relativos más altos del estómago respecto a los del pienso control y de pectinas (11 y 56 % respectivamente; P < 0,05). Por otra parte, el peso relativo del ciego aumentó en los animales que consumieron tanto la fracción soluble como insoluble de la pulpa de remolacha, siendo un 16% más pesados (P < 0,001) que el grupo control. El pH del contenido cecal fue más bajo en los animales del grupo de pulpa de remolacha que en los del grupo control (5,64 vs. 6,03; P < 0,001), mientras que los del grupo de pectinas y de fibra insoluble de pulpa de remolacha mostraron valores intermedios. En conclusión, el efecto positivo de la pulpa de remolacha en el flujo de mucinas a nivel ileal se debe a la fracción soluble e insoluble de la pulpa de remolacha. La mitad de la fibra soluble de la pulpa de remolacha desaparece antes de llegar al ciego, independientemente si esta proviene de pectinas puras o de la pulpa de remolacha. El pH cecal esta mejor correlacionado con la cantidad de FDT que desaparece antes del ciego más que con la que se degrada en el ciego. En el último estudio se estudiaron los efectos de la fibra soluble e insoluble de la pulpa de manzana sobre la digestibilidad de la fibra y algunos parámetros digestivos. Cuatro dietas fueron formuladas con niveles similares de fibra insoluble (aFNDmo-pb 32,4%) y proteína (18,6% ambos en base seca). El pienso control contuvo el nivel más bajo de fibra soluble (46 g de fibra soluble/kg, con cascarilla de girasol y paja de cereales como la fuentes de fibra). Un segundo pienso fue obtenido mediante la sustitución de 60 g de almidón/kg del pienso control por pectinas de manzana (105 g fibra soluble/kg). Los otros dos piensos se obtuvieron por la substitución de parte de las fuentes de fibra del pienso control por pulpa de manzana o pulpa de manzana despectinizada (93 y 71 g de fibra soluble/kg, respectivamente). La digestibilidad fecal fue determinada en 23 conejos/pienso con 1.68 ± 0.23 kg de peso vivo, los cuales fueron sacrificados a los 60 d edad para recolectar su contenido digestivo para determinar digestibilidad ileal y otros parámetros digestivos. La fibra soluble de manzana (pectinas y pulpa entera) estimuló el flujo ileal de mucinas (P = 0,002), pero no asi la pulpa despectinizada. La corrección por mucinas incrementó la digestibilidad de la FDT y la fibra soluble a nivel fecal, y especialmente a nivel ileal. Cerca de la mitad de la fibra soluble proveniente de los piensos con cualquiera de las fracciones de la pulpa de manzana fue degradada a nivel ileal, sin mostrar diferencias entre los grupos (46 y 86% en promedio a nivel ileal y fecal respectivamente). La inclusión de pulpa despectinizada de manzana mejoró la digestibilidad de la FND a nivel fecal (P < 0,05) pero no a nivel ileal. El contenido cecal de los conejos alimentados con la pulpa de manzana tuvieron el pH cecal más ácido que los del pienso control (5,55 vs. 5,95. P < 0,001), mientras que los animales con el pienso de pectinas de manzana y de pulpa de manzana despectinizada mostraron valores intermedios. En conclusión los efectos positivo de la pulpa de manzana en el flujo de mucinas se debió principalmente a la fracción soluble de la pulpa de manzana. La mitad de la fibra soluble fue degradada antes del ciego independientemente de si esta provino de las pectinas o de la pulpa de manzana. El pH cecal estuvo mejor correlacionado con la cantidad de FDT fermentada en todo el tracto digestivo y antes de llegar al ciego que con la que se degradó en el ciego. Al integrar los resultados de los estudio 2, 3 y 4 se concluyó que la corrección de mucinas de los contenidos digestivos al determinar FDT y fibra soluble es necesaria para ajustar los cálculos de su digestibilidad. Esta corrección es mucho más importante a nivel ileal y en dietas bajas en fibra soluble. Por otra parte, la FDT desapareció en proporciones importantes antes de llegar al ciego, especialmente en piensos que contienen pulpa de remolacha o de manzana o alguna fracción soluble o insoluble de las mismas y estas diferencias observadas entre los piensos a nivel ileal se correlacionaron mejor con el pH cecal, lo que indicaría que la FDT se solubilizó antes de llegar al ciego y una vez en esté fermentó. Estos resultados implican que determinar la fibra soluble como FDSaFNDmo-pb es la mejor opción y que en la determinación de la digestibilidad de la FDT y fibra soluble se debe considerar la corrección por mucinas especialmente a nivel ileal y en piensos bajos en fibra soluble. ABSTRACT The present thesis constitutes a step forward in advancing the knowledge of the methods to quantify soluble fibre and the effects of the fibre fractions and source of fibre on the site the digestion of different fractions of fibre (soluble and insoluble) in the rabbit. There is a positive effect of soluble fibre on rabbit digestive health and therefore on the reduction of mortality in weaning rabbits. Nevertheless, it is no so clear that the effects of soluble fibre on rabbits are due particularly to this fraction. This thesis aims: 1) to compare the quantification of soluble fibre in feeds using different chemical and in vitro approaches, and to study the potential interference between soluble fibre and mucin determinations, 2) to identify the effects of type of fibre, site of fermentation, method to quantify insoluble and soluble fibre, and correction of the intestinal soluble fibre content for intestinal mucin on the digestibility of fibre fractions and 3) to evaluate the individual effect of soluble and insoluble fibre from sugar beet pulp and apple pulp on ileal and faecal soluble and insoluble digestibility and digestive traits. These objectives were developed in four studies: The first study compared the quantification of soluble fibre in feeds using different chemical and in vitro approaches, and studied the potential interference between soluble fibre and mucin determinations. Six ingredients, sugar beet pulp (SBP), SBP pectins, insoluble SBP, wheat straw, sunflower hulls and lignocellulose, and seven rabbit diets, differing in soluble fibre content, were evaluated. In experiment 1, ingredients and diets were analysed for total dietary fibre (TDF), insoluble dietary fibre (IDF), soluble dietary fibre (SDF), aNDFom (corrected for protein, aNDFom-cp) and 2-step pepsin/pancreatin in vitro DM indigestibility (corrected for ash and protein, ivDMi2). Soluble fibre was estimated by difference using three procedures: TDF - IDF (SDFIDF), TDF - ivDMi2 (SDFivDMi2), and TDF - aNDFom-cp (SDFaNDFom-cp). Soluble fibre determined directly (SDF) or by difference, as SDFivDMi2 were not different (109 g/kg DM, on average). However, when it was calculated as SDFaNDFom-cp the value was 40% higher (153 g/kg DM, P < 0.05), whereas SDFIDF (124 g/kg DM) did not differ from any of the other methods. The correlation between the four methods was high (r ≥ 0.96. P ≤ 0.001. n = 13), but it decreased or even disappeared when SBP pectins and SBP were excluded and a lower and more narrow range of variation of soluble fibre was used. In experiment 2, the ivDMi2 using crucibles (reference method) were compared to those made using individual or collective ankom bags in order to simplify the determination of SDFivDMi2. The ivDMi2 was not different when using crucibles or individual or collective ankom bags. In experiment 3, the potential interference between soluble fibre and intestinal mucin determinations was studied using rabbit intestinal raw mucus, digesta and SBP pectins, lignocelluloses and a rabbit diet. An interference was observed between the determinations of soluble fibre and crude mucin, as the content of TDF and apparent crude mucin were high in SBP pectins (994 and 709 g/kg DM) and rabbit intestinal raw mucus (571 and 739 g/kg DM). After a pectinase treatment, the coefficient of apparent mucin recovery of SBP pectins was close to zero, whereas that of rabbit mucus was not modified. An estimation of the crude mucin carbohydrates retained in digesta TDF is proposed to correct TDF and soluble fibre digestibility. In conclusion, the values of soluble fibre depend on the methodology used. The contamination of crude mucin with soluble fibre is avoided using pectinase. The second study focused on the effect of type of fibre, site of fermentation, method for quantifying insoluble and soluble dietary fibre, and their correction for intestinal mucin on fibre digestibility. Three diets differing in soluble fibre were formulated (85 g/kg DM soluble fibre, in the low soluble fibre [LSF] diet; 102 g/kg DM in the medium soluble fibre [MSF] diet; and 145 g/kg DM in the high soluble fibre [HSF] diet). They were obtained by replacing half of the dehydrated alfalfa in the MSF diet with a mixture of beet and apple pulp (HSF diet) or with a mix of oat hulls and soybean protein (LSF diet). Thirty rabbits with ileal T-cannulas were used to determine total tract apparent digestibility (CTTAD) and ileal apparent digestibility (CIAD). Caecal digestibility was determined by difference between CTTAD and CIAD. Insoluble fibre was measured as aNDFom-cp, IDF, and ivDMi2, whereas soluble fibre was calculated as SDFaNDFom-cp, SDFIDF, SDFivDMi2. The intestinal mucin content was used to correct the TDF and soluble fibre digestibility. Ileal and faecal concentration of mucin increased from the LSF to the HSF diet group (P < 0.01). Once corrected for intestinal mucin, The CTTAD and CIAD of TDF and soluble fibre increased whereas caecal digestibility decreased (P < 0.01). The CIAD of TDF increased from the LSF to the HSF diet group (0.12 vs. 0.281. P < 0.01), with no difference in the caecal digestibility (0.264), resulting in a higher CTTAD from the LSF to the HSF diet group (P < 0.01). The CIAD of insoluble fibre increased from the LSF to the HSF diet group (0.113 vs. 0.21. P < 0.01), with no difference in the caecal digestibility (0.139) and no effect of fibre method, resulting in a higher CTTAD for rabbits fed the HSF diet compared with the MSF and LSF diets groups (P < 0.01). The CTTAD of aNDFom-cp was higher compared with IDF or ivDMi2 (P < 0.01). The CIAD of soluble fibre was higher for the HSF than for the LSF diet group (0.436 vs. 0.145. P < 0.01) and fibre method did not affect it. Caecal soluble fibre digestibility decreased from the LSF to the HSF diet group (0.721 vs. 0.492. P < 0.05). The lowest caecal and faecal soluble fibre digestibility was measured using SDFaNDFom-cp (P < 0.01). There was a high correlation among the digestibilities of soluble fibre measured as SDFaNDFom-cp, SDFIDF, and SDFivDMi2. Therefore, these methodologies provide similar information. However, the method that seems to be globally better related to the physiological traits (ileal flow of mucins, and relative weight of the caecum and caecal pH from previous work) was the SDFaNDFom-cp. In conclusion, a correction for intestinal mucin is necessary for ileal TDF and soluble fibre digestibility whereas the selection of the fibre method has a minor relevance. The inclusion of sugar beet and apple pulp increased the amount of TDF fermented in the small intestine. The third study examined the effect of fibre fractions of sugar beet pulp (SBP) and the method for quantifying soluble and insoluble fibre on soluble and insoluble fibre digestibility and digestive traits. Four diets were formulated with similar level of insoluble fibre (aNDFom-cp: 315 g/kg DM) and protein (167 g/kg DM). Control diet contained the lowest level of soluble fibre (30.3 g/kg DM, including sunflower hulls and straw as sole sources of fibre). A second diet was obtained by replacing 60 g starch/kg of control diet with SBP pectins (82.9 g soluble fibre/kg DM). Two more diets were obtained by replacing part of the fibrous sources of the control diet with either insoluble SBP fibre or SBP (42.2 and 82.3 g soluble fibre/kg DM, respectively). Fifty six (14/diet) rabbits weighing 2.40  0.213 kg were used to determine faecal and ileal digestibility of total dietary fibre (TDF), insoluble dietary fibre (IDF), neutral detergent fibre corrected for ash and CP (aNDFom-cp) and soluble fibre estimated as SDFaNDFom-cp and SDFIDF. Faecal and ileal mucin content was used to correct TDF and soluble fibre digestibility. It was also recorded weight of digestive segments and digesta pH. Rabbits fed insoluble SBP showed the lowest feed intake with respect to the other 3 diets (124 vs. 139 g/d, respectively. P < 0.05). Ileal mucin flow was higher (P < 0.05) in animals fed pectin and SBP diets (9.0 g/d, as average) than those fed control diet (4.79 g/d), showing InsSBP group an intermediate value. No differences on mucin content were detected at faecal level. There was no diet effect on the CIAD of TDF (corrected for mucin) and insoluble fibre. Fibre methodology influenced the CIAD of insoluble fibre (0.123 for IDF vs. 0.108 for aNDFom-cp. P < 0.01). Anyway, the amount of insoluble fibre fermented before the caecum did not differ between both methods (4.9 g/d, on average). Rabbits fed insoluble SBP and SBP diets showed the highest CTTAD of insoluble fibre (0.266 on average vs. 0.106 for control group), whereas those fed pectin diet had an intermediate value (0.106. P < 0.001). The CTTAD of insoluble fibre measured with IDF was higher than that measured with aNDFom-cp (by 20%. P < 0.001). It led that the amount of insoluble fibre fermented along the digestive tract were different (9.5 or 7.5 g/d when calculated as IDF or aNDFom-cp, respectively; P < 0.001). When the CIAD of soluble fibre was corrected for mucin they became positive (P < 0.001) except for control group measured as SDFIDF. Once corrected for mucin content, rabbits fed soluble fibre from SBP (pectin and SBP groups) showed higher CIAD of soluble fibre than control group (0.483 vs. -0.019. respectively), whereas the value for insoluble SBP group was intermediate 0.274. The CTTAD of soluble fibre (mucin corrected) was similar among diets 0.93. Rabbits fed with SBP and insoluble SBP diets showed higher total digestive tract and stomach relative weight than those fed pectin and control diets (by 11 and 56 %. respectively, P < 0.05). The caecal relative weight did not differ in rabbits fed pectin, insoluble SBP, and SBP diets (62 g/kg BW, as average) and they were on average 16% higher (P < 0.001) than in control group. Caecal content of rabbits fed SBP diet was more acid than those fed control diet (5.64 vs. 6.03. P < 0.001), whereas those from pectin and insoluble SBP diets showed intermediate values. In conclusion, the positive effect of SBP fibre on ileal mucin flow was due to both its soluble and insoluble fibre fraction. Half of the soluble SBP fibre was degraded before the caecum independently it came from pectin or SBP. The caecal pH correlated better with the ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. The last study examined the effect of soluble and insoluble fibre of apple pulp on fibre digestibility and digestive traits. Four diets were formulated with similar level of insoluble fibre (aNDFom-cp: 324 g/kg DM) and protein (18.6 g/kg DM). Control diet contained the lowest level of soluble fibre (46 g soluble fibre/kg DM, including oat hulls and straw as sole sources of fibre). A second diet was obtained by replacing 60 g starch/kg of control diet with apple pectins (105 g soluble fibre/kg DM). Two more diets were obtained by substituting part of the fibrous sources of the control diet by either apple pulp or depectinized apple pulp (93 and 71 g soluble fibre/kg, respectively). The CTTAD was determined in 23 rabbits/diet weighing 1.68  0.23 kg BW, and 23 rabbits/diet were slaughtered at 60 d of age to collect ileal digesta to determine CIAD and record other digestive traits. Soluble fibre from apple stimulated ileal flow of mucin (P = 0.002), but depectinized apple pulp did not. The correction for mucin increased the digestibility of crude protein, total dietary fibre, and soluble fibre at faecal, but especially at ileal level, depending in this case on the diet. Around half of the soluble fibre in diets containing any fibre fraction from apple was degraded at ileal level, with no differences among these diets (0.46 vs. 0.066 for control group, P=0.046). Faecal soluble fibre digestibility was 0.86 on average for all groups). Inclusion of the apple insoluble fibre improved NDF digestibility at faecal (0.222 vs. 0.069. P < 0.05) but not at ileal level. Caecal content of rabbits fed apple pulp diet was more acid than those fed control diet (5.55 vs. 5.95. P < 0.001), whereas those from pectin and depectinised apple pulp diets showed intermediate values. In conclusion, the positive effect of apple fibre on ileal mucin flow was mainly due to its soluble fibre fraction. Half of the soluble apple fibre was degraded before the caecum independently it came from pectin or apple pulp. The caecal pH correlated better with the total and ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. The results obtained in the studies 2, 3 and 4 were considered together. These results showed that the mucin correction is necessary when the TDF and soluble fibre digestibility is determined, and it correction is more important at ileal level and in diets with low level of soluble fibre. On another hand, incrementing the soluble fibre using sugar beet and apple pulp increased the amount of TDF disappear before the caecum. Moreover, the caecal pH correlated better with the ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. This suggests that an ileal fibre solubilisation may occur rather than ileal fermentation. Therefore the implications of this work were that: the estimation of soluble fibre as SDFaNDFom-cp is an adequate method considering its correlation with the physiological effects; and the TDF and soluble fibre digestibility must be corrected with intestinal mucins, especially when the ileal digestibility is determined.

Effect of the season on the free phytoprostanes content in Cornicabra extra virgin olive oil from deficit irrigated olive trees

BACKGROUND: The effect of regulated deficit irrigation (RDI) on the phytoprostane (PhytoP) content in extra virgin olive (Olea europaea L., cv. Cornicabra) oil (EVOO) was studied. During the 2012 and 2013 seasons, T0 plants were irrigated at 100% ETc, while T1 and T2 plants were irrigated avoiding water deficit during phases I and III of fruit growth and saving water during the non-critical phenological period of pit hardening (phase II), developing amore severewater deficit in T2 plants. In 2013, a fourth treatment (T3) was also performed, which was similar to T2 except that water saving was from the beginning of phase II to 15 days after the end of phase II. RESULTS: 9-F1t-PhytoP, 9-epi-9-F1t-PhytoP, 9-epi-9-D1t-PhytoP, 9-D1t-PhytoP, 16-B1-PhytoP and 9-L1-PhytoP were present in Cornicabra EVOO, and their contents increased in the EVOO fromRDI plants. CONCLUSION: Deficit irrigation during pit hardening or for a further period of 2 weeks thereafter to increase irrigation water saving is clearly critical for EVOO composition because of the enhancement of free PhytoPs, which have potential beneficial effects on human health. The response of individual free PhytoPs to changes in plant water status was not as perceptible as expected, preventing their use as biomarkers of water stress.

Comparative study of the pathogenicity of seabed isolates of Fusarium equiseti and the effect of the composition of the mineral salt medium and temperature on mycelia growth

The pathogenicity of seven strains of Fusarium equiseti isolated from seabed soil was evaluated on different host plants showing pre and post emergence damage. Radial growth of 27 strains was measured on culture media previously adjusted to different osmotic potentials with either KCl or NaCl (-1.50 to - 144.54 bars) at 15º, 25º and 35º C. Significant differences and interactive effects were observed in the response of mycelia to osmotic potential and temperature.

Effect of the curing conditions of concrete on the behaviour under freeze-thaw cycles*

The aim of this work is to relate the curing conditions of concrete and the addition of an air-entraining admixture with the damage caused by freeze–thaw cycles. In countries with a continental climate, the curing of concrete in summer is performed under climatic conditions of high temperature and low humidity, and during the winter the concrete suffers conditions of freeze–thaw, often accompanied by the use of de-icing salts. This paper shows the experimental results of the behaviour of concrete specimens cured under climatic summer conditions (high temperature and low humidity) and then subjected to freeze–thaw cycles. Curing of the specimens includes conditions of good and bad practice in relation to wetting and protection of the concrete. It also examines the effectiveness of using an air-entraining admixture in both cases. The experimental programme includes an evaluation of the mechanical properties of the concrete, the study of the cement hydration and the measurement of the volume and pore sizes of the concrete. These tests were performed before and after the application of the freeze–thaw cycles. The results obtained showed that the specimens without air-entraining admixture show a deterioration of mechanical properties after the freeze–thaw test. However, the inclusion of air bubbles benefits the behaviour of concrete against freeze–thaw cycles so even better mechanical properties after the test were observed. This anomalous behaviour is because the cement hydration process continues over the freeze–thaw tests, closing the pore structure. This aspect has been confirmed with the DTA and TG tests performed