Band gap control via tuning of inversion degree in CdIn2S4 spinel

Based on theoretical arguments, we propose a possible route for controlling the band-gap in the promising photovoltaic material CdIn2S4. Our ab initio calculations show that the experimental degree of inversion in this spinel (fraction of tetrahedral sites occupied by In) corresponds approximately to the equilibrium value given by the minimum of the theoretical inversion free energy at a typical synthesis temperature. Modification of this temperature, or of the cooling rate after synthesis, is then expected to change the inversion degree, which in turn sensitively tunes the electronic band-gap of the solid, as shown here by screened hybrid functional calculations.

A novel topology control approach to maintain the node degree in dynamic wireless sensor networks

Topology control is an important technique to improve the connectivity and the reliability of Wireless Sensor Networks (WSNs) by means of adjusting the communication range of wireless sensor nodes. In this paper, a novel Fuzzy-logic Topology Control (FTC) is proposed to achieve any desired average node degree by adaptively changing communication range, thus improving the network connectivity, which is the main target of FTC. FTC is a fully localized control algorithm, and does not rely on location information of neighbors. Instead of designing membership functions and if-then rules for fuzzy-logic controller, FTC is constructed from the training data set to facilitate the design process. FTC is proved to be accurate, stable and has short settling time. In order to compare it with other representative localized algorithms (NONE, FLSS, k-Neighbor and LTRT), FTC is evaluated through extensive simulations. The simulation results show that: firstly, similar to k-Neighbor algorithm, FTC is the best to achieve the desired average node degree as node density varies; secondly, FTC is comparable to FLSS and k-Neighbor in terms of energy-efficiency, but is better than LTRT and NONE; thirdly, FTC has the lowest average maximum communication range than other algorithms, which indicates that the most energy-consuming node in the network consumes the lowest power.

Labor risk prevention culture encouragement among students from building degree in the Technical University of Madrid

The influence of training in labor risk prevention and the development of the resulting pre-emptive culture are analyzed within this paper. In order to achieve this, a quantitative analysis of the students of Building Degree in the Technic University of Madrid has been developed. This study has been made in all grades, valuating the previous knowledge acquired during compulsory education. It must be kept in mind that the students in 3rd and 4th grade have received general and specific compulsory training in prevention and safety in the building sector.

Considerations on the success rate in aeronautical engineering studies in Spain

The relationship between different learning evaluation methods and the academic success in an aeronautical engineering degree in Spain is analysed. The study is based on data about the evolution of academic achievement obtained along the last ten year, along which the evaluation and learning’s methods have suffered huge changes.

Active learning and generic competences in an operating systems course

The Bologna Declaration and the implementation of the European Higher Education Area are promoting the use of active learning methodologies. The aim of this study is to evaluate the effects obtained after applying active learning methodologies to the achievement of generic competences as well as to the academic performance. This study has been carried out at the Universidad Politécnica de Madrid, where these methodologies have been applied to the Operating Systems I subject of the degree in Technical Engineering in Computer Systems. The fundamental hypothesis tested was whether the implementation of active learning methodologies (cooperative learning and problem based learning) favours the achievement of certain generic competences (‘teamwork’ and ‘planning and time management’) and also whether this fact improved the academic performance of our students. The original approach of this work consists in using psychometric tests to measure the degree of acquired student’s generic competences instead of using opinion surveys, as usual. Results indicated that active learning methodologies improve the academic performance when compared to the traditional lecture/discussion method, according to the success rate obtained. These methods seem to have as well an effect on the teamwork competence (the perception of the behaviour of the other members in the group) but not on the perception of each students’ behaviour. Active learning does not produce any significant change in the generic competence ‘planning and time management'.

A Coordinated Plan for Teaching Software Engineering in the University Rey Juan Carlos.

Un plan para organizar las enseñanzas de la ingeniería del software en las titulaciones de informática de la URJC. Nowadays both industry and academic environments are showing a lot of interest in the Software Engineering discipline. Therefore, it is a challenge for universities to provide students with appropriate training in this area, preparing them for their future professional practice. There are many difficulties to provide that training. The outstanding ones are: the Software Engineering area is too broad and class hours are scarce; the discipline requires a high level of abstraction; it is difficult to reproduce real world situations in the classroom to provide a practical learning environment; the number of students per professor is very high (at least in Spain); companies develop software with a maturity level rarely over level 2 of the CMM for Software (again, at least in Spain) as opposed to what is taught at the University. Besides, there are different levels and study plans, making more difficult to structure the contents to teach in each term and degree. In this paper we present a plan for teaching Software Engineering trying to overcome some of the difficulties above.