Effects of different soil management practices on soil mechanic resistance and seed depth placement in a maize crop in Alentejo, Portugal Mediterranean region.

No tillage, minimum tillage and conventional tillage practices are commonly used in maize crops in Alentejo, affecting soil physic conditions and determining seeders performance. Seeders distribution can be evaluated in the longitudinal and vertical planes. Vertical plane is specified by seeding depth (Karayel et al., 2008). If, in one hand seeding depth uniformity is a goal for all crop establishment , in the other hand, seeders furrow openers depth control is never constant depending on soil conditions. Seed depth uniformity affects crop emergence, Liu et al. (2004) showed an higher correlation between crop productivity and emergence uniformity than with longitudinal plants distribution. Neto et al. (2007) evaluating seed depth placement by measuring maize mesocotyl length under no tillage conditions in 38 farms concluded that 20% of coefficient of variation suggests the need of improvement seeders depth control mechanisms. The objective of this study was to evaluate casual relationships and create spatial variability maps between soil mechanic resistance and vertical distribution under three different soil practices to improve seed depth uniformity.

Differences brick facade design to horizontal loads between the Spanish and European standards

Brick facades are a construction type, strongly linked to local construction characteristics and methods. In Spain, particularly in Castilla, the facades have been built since the '80s with Castilian half foot (11.5 cm), resting on the edge of slabs. The design of these facades, to horizontal loads from wind, depending on the codes used, can lead to completely different valid solutions. Applying same loads, the facades studied with current European standard (Eurocode 6), have a maximum length of 7.1 m between supports, while the Spanish code, Technical Building Code - Structural Safety Masonry, (CTE SE-F), 8.4 m can be achieved. This represents an increase of flexural strength, depending on the calculation model used, which can reach until 8 times. This is due to the difference of the calculation method and the structural model in one and another standard, depending on if this facade is analyzed as a vertical or horizontal beam or by formation of a vertical or horizontal archh. This paper analyzes the constructive solution of the brick facades that results from applying Spanish or European standards and how it affects the model applied in the safety of the resulting facade.

A partial study of vertical distribution of conventional no-till seeders and spatial variability of seed depth placement of maize in the Alentejo region, Portugal

The requirements for a good stand in a no-till field are the same as those for conventional planting as well as added field and machinery management. Among the various factors that contribute towards producing a successful maize crop, seed depth placement is a key determinant. Although most no-till planters on the market work well under good soil and residue conditions, adjustments and even modifications are frequently needed when working with compacted or wet soils or with heavy residues. The main objective of this study, carried out in 2010, 2011 and 2012, was to evaluate the vertical distribution and spatial variability of seed depth placement in a maize crop under no-till conditions, using precision farming technologies and conventional no-till seeders. The results obtained indicate that the seed depth placement was affected by soil moisture content and forward speed. The seed depth placement was negatively correlated with soil resistance and seeding depth had a significant impact on mean emergence time and the percentage of emerged plants. Shallow average depth values and high coefficients of variation suggest a need for improvements in controlling the seeders’ sowing depth mechanism or more accurate calibration by operators in the field.

Spatial variability of seed depth placement of maize under no tillage in Alentejo, Portugal

Among the various factors that contribute towards producing a successful maize crop, seed depth placement is a key determinant, especially in a no-tillage system. The main objective of this work was to evaluate the spatial variability of seed depth placement and crop establishment in a maize crop under no-tillage conditions, using precision farming technologies. The obtained results indicate that seed depth placement was significantly affected by soil moisture content, while a very high coefficient of variation of 39% was found for seed depth. Seeding depth had a significant impact on mean emergence time and percentage of emerged plants. Shallow average depth values and the high coefficient of variation suggest a need for improvement in controlling the seeders sowing depth.

Contribute to the Study of Vertical Distribution of Conventional No-Till Seeders and Spatial Variability of Seed Depth Placement of Maize in Alentejo, Portugal

Entre os vários fatores que contribuem para a produção de uma cultura de milho, a distribuição vertical dos semeadores avaliada através da localização da semente em profundidade é um fator-chave, especialmente na técnica de sementeira direta. Simultaneamente, dada a complexidade dos ecossistemas naturais e agrícolas em sistemas de agricultura de conservação, a gestão diferenciada e localizada das parcelas assume um importante papel na análise e gestão da variabilidade das propriedades do solo e estabelecimento das culturas, nomeadamente utilizando informação geo referenciada e tecnologia expedita. Assim, o principal objetivo desta Tese foi a avaliação em culturas de milho da variabilidade espacial da localização de semente em profundidade e estabelecimento da cultura em sementeira direta usando sistemas convencionais de controlo de profundidade, tendo-se comparado com diferentes sistemas de mobilização e recorrendo a tecnologias de agricultura de precisão. Os ensaios decorreram na região Mediterrânea do Alentejo, em propriedades agrícolas no decorrer das campanhas de 2010, 2011, 2012 e 2015 em 6 diferentes campos experimentais. O trabalho experimental consistiu em ensaios com avaliações in loco do solo e cultura, consumo de combustível das operações e deteção remota. Os resultados obtidos indicam que não só o sistema de mobilização afetou a localização da semente em profundidade, como em sementeira direta a profundidade de sementeira foi afetada pelo teor de humidade do solo, resistência do solo à profundidade e velocidade da operação de sementeira. Adicionalmente observaram-se condições heterogéneas de emergência e estabelecimento da cultura afetadas por condições físicas de compactação do solo. Comparando os diferentes sistemas de mobilização, obteve-se uma significativa redução de combustível para a técnica de sementeira direta, apesar de se terem observado diferenças estatísticas significativas considerando diferentes calibrações de profundidade de sementeira Do trabalho realizado nesta Tese ressalva-se a importância que as tecnologias de agricultura de precisão podem ter no acompanhamento e avaliação de culturas em sementeira direta, bem como a necessidade de melhores procedimentos no controlo de profundidade dos semeadores pelo respetivos operadores ou ao invés, a adoção de semeadores com mecanismos ativos de controlo de profundidade. ABSTRACT Among the various factors that contribute towards producing a successful maize crop, seeders vertical distribution evaluated through seed depth placement is a key determinant, especially under a no-tillage technique. At the same time in conservation agriculture systems due to the complexity of natural and agricultural ecosystems site specific management became an important approach to understand and manage the variability of soil properties and crop establishment, especially when using geo spatial information and affording readily technology Thus, the main objective of this Thesis was to evaluate the spatial variability of seed depth placement and crop establishment in maize crops under no-tillage conditions compared to different tillage systems, using conventional seed depth control no till seeders and precision farming technologies. Trials were carried out in the Mediterranean region of Alentejo, in private farms along the sowing operations season over the years 2010, 2011, 2012 and 2015 in 6 different experimental fields. Experimental work covered field tests with in loco soil and crop evaluations, fuel operation evaluations and aerial sensing. The results obtained indicate that not only tillage system affected seed depth placement but under no till conditions seed depth was affected by soil moisture content, soil resistance to penetration and seeders forward speed. In addition uneven crop seedling and establishment depended on seed depth placement and could be affected by physical problems of compaction layers. Significant reduction in fuel consumption was observed for no till operations although significant differences observed according to different setting calibrations of seed depth control. According to the results, precision agriculture is an important tool to evaluate crops under no till conditions and seed depth mechanisms should be more accurate by the operators or is determinant the adoption of new active depth control technology to improve seeders performance.

Estudio experimental del Sistema de Albañilería Integral en la construcción de viviendas sismorresistentes. Experimental study of the Integral Masonry System in the construction of earthquake resistant houses

This paper presents the application of the Integral Masonry System (IMS) to the construction of earthquake resistant houses and its experimental study. To verify the security of this new type of building in seismic areas of the third world two prototypes have been tested, one with adobe and the other with hollow brick. In both cases it’s a two-story 6x6x6 m3 house built to scale 1/2. The tests are carried out at the Laboratory of Antiseismic Structures of the Department of Engineering, Pontifical Catholic University of Peru in Lima, in collaboration with the UPM (Technical University of Madrid). This article shows the design process of the prototypes to test, including the sizing of the reinforcements, the characteristics of the tests and the results obtained. These results show that the IMS with adobe or brick remains stable with no significant cracks faced with a severe earthquake, with an estimated acceleration of 1.8 g. Este artículo presenta una aplicación del Sistema de Albañilería Integral (SAI) a la construcción de viviendas sismorresistentes y su estudio experimental. Para verificar su seguridad para su construcción en zonas sísmicas del tercer mundo se han ensayado dos prototipos, uno con adobe, y otro con ladrillo hueco. Se trata de una vivienda de 6x6x6 m3 y dos plantas que se construyen a escala 1/2. Los ensayos se realizaron en el Laboratorio de Estructuras Antisísmicas del Departamento de Ingeniería de la Pontificia Católica Universidad del Perú (PUCP) de Lima en colaboración con la UPM (Universidad Politécnica de Madrid). Este artículo muestra el proceso de diseño de los prototipos a ensayar, incluido el dimensionado de los refuerzos, las características de los ensayos y los resultados obtenidos. Estos resultados muestran que el SAI con adobe o ladrillo permanece estable sin grietas significativas ante un sismo severo, con una aceleración estimada de 1,8 g.

Recovery of traditional mortars in the laboratory of materials at the school of architectura of Madrid

The Laboratory of Materials seminar is an optional course offered to students in the School of Architecture in Madrid. It is taught during 35 class hours in the laboratory of materials distributed in two hours and forty minutes weekly. One of the working lines is the preparation of traditional mortars made by students groups, each one of 4 or 5 members. It is basically a practical course, and students have to prepare a group of tests pieces in order to confirm the initial hypothesis, or when needed, make innovations. The test pieces are of 150mmx150mmx10mm and applied to big size hollow bricks, prismatic test pieces of 40mmx40mmx160mm to apply physical and mechanical tests and brick wallings of varied dimensions.

Mecanización agraria y empleo en el regadío Extremeño

El progreso tecnológico y la mecanización han provocado siempre, a corto plazo, la amortización de puestos directivos de trabajo, generándose fuerte resistencia entre los anteriormente asalariados. La revuelta de los «canuts», por ejemplo en Francia, oponiéndose a la introducción de las máquinas tejedoras, forma parte de la historia del movimiento obrero del siglo XIX. La mecanización agraria no podía ser, evidentemente, la excepción. El Elemento nuevo, introducido por la presente crisis económica, es la desaparición de empleos alternativos en otras ramas de la producción u otros sectores productivos. La resistencia al desarrollo de la mecanización en el campo cobra actualmente su orina quizás más espectacular en los ataques a las cosechadoras de algodón, pero sobre todo permite la generalización de un estado de ánimo contrario en amplias capas de la población, sobre todo en Andalucía y Extremadura. Hoy no podemos seguir utilizando sencillamente los mismos conceptos productivistas de etapas económicas anteriores, aunque los autores se resisten a una oposición sistemática a la mecanización para la realización de las labores agrícolas. Con Maylor y Ver non (1969) podemos destacar el papel de la empresa y el empresario (en nuestro caso, el agricultor) a la hora de la adopción de las decisiones relativas al cómo y al qué producir. El análisis microeconómico aparece, entonces, como una útil herramienta para analizar la incidencia de un desplazamiento de la función de producción hacia una mayor intensidad en la utilización tanto del capital de explotación como del factor trabajo. En esta línea, el presente trabajo se limita al análisis del regadío extremeño —un buen ejemplo de los sistemas de agricultura del riego mediterráneo (C.M. Portas, 1983) en base a datos recogidos y contrastados por nosotros. Están basados en tiempos reales medios determinados en base a las hojas de cultivo de las fincas colaboradoras del Servicio de Extensión Agraria (S.E.A.) de Badajoz. Las conclusiones que podemos sacar del estudio no pueden, entonces, generalizarse fuera de su contexto y de sus limitaciones. Creemos que nuestros resultados al plantearse en unos términos geográficos específicos no pierden interés, sino que pueden servir, junto con otras investigaciones semejantes, para alcanzar conclusiones generales en un futuro, en un «proceso de enriquecimiento continuo entre lo general y lo particular» como señala Tuñón de Lara (1981). Entre los antecedentes más directos de este estudio, podemos destacar el de PINHEIRO y PORTAS (1980). Su contribución no se ha limitado a la aportación de información y documentación útil para contrastar nuestros resultados con la situación del Alentejo portugués, sino que ha sido constante animador en la elaboración.

Fundamentos constructivos de las fortificaciones fronterizas entre las coronas de Castilla y Aragón de los siglos XII al XV en la actual provincia de Soria

La tesis doctoral desarrolla una investigación original, dentro del marco disciplinario de la historia de la construcción, sobre los fundamentos constructivos de las fortificaciones bajomedievales fronterizas entre las Coronas de Castilla y Aragón en la actual provincia de Soria. En el título de la tesis ya queda expresado el objeto fundamental y fundacional, así como el ámbito temporal —desde la reconquista del oriente soriano por parte de Alfonso I el Batallador a principios del siglo XII hasta la unificación de las coronas hispánicas en el siglo XV bajo el común mandato de los Reyes Católicos— y la extensión territorial que delimita la investigación: aquéllas comarcas castellanas lindantes con Aragón pertenecientes a la actual provincia de Soria. Durante este período bajomedieval se produjeron una serie de enfrentamientos fronterizos que obligó a fortificar la frontera y las vías de comunicación entre ambas coronas. La falta de estudios de conjunto de estas fortificaciones entendiéndolas como participantes en un sistema fortificado ha constituido la justificación de la investigación, que se realiza en varios niveles de análisis: territorial, histórico, arquitectónico, poliorcético y constructivo. Así mismo, se ha detectado cierta falta de rigor acompañada de inexactitudes en las consideraciones constructivas publicadas sobre algunas de las fortificaciones del ámbito de estudio, lo que ha provocado errores en su datación al no más haber elementos de corte artístico o estilístico que marquen indudablemente la pertenencia a una época. En la tesis se ponen en duda las dataciones tradicionalmente aceptadas planteando la hipótesis que da pie a la investigación: ante la falta de elementos artísticos o estilísticos en unos sobrios edificios eminentemente funcionales es posible establecer con suficiente aproximación la fecha de construcción en base a criterios constructivos una vez formada una clasificación cronotipológica de cada técnica constructiva. La hipótesis, por lo tanto, plantea un objetivo principal —el estudio de la razón constructiva del sistema fortificado fronterizo— desarrollado en una serie de objetivos específicos cuya consecución programa los sucesivos niveles de análisis: - Conocer y detallar los elementos históricos que originaron los enfrentamientos entre las Coronas de Castilla y Aragón y su desarrollo mediante herramientas historiográficas y analizar las características naturales del territorio en litigio mediante instrumentos cartográficos. - Conocer y analizar los tipos arquitectónicos y las tradiciones constructivas empleadas en las construcciones castrenses en el ámbito temporal en que se enmarca la investigación. - Localizar, documentar y seleccionar para su análisis las fortalezas y construcciones militares erigidas durante dichas luchas fronterizas en la actual provincia de Soria a través del trabajo de campo y métodos cartográficos y bibliográficos. - Realizar un estudio general sobre el sistema fortificado a escala territorial - Investigar la tipología arquitectónica, poliorcética y constructiva del conjunto de estas fortificaciones bajomedievales fronterizas. - Analizar los fundamentos constructivos de los casos de estudio seleccionados entre estas construcciones y caracterizarlas en cuanto al material, elementos, sistemas y procesos constructivos. - Ordenar la información histórica dispersa y corregir errores para hacer una base sobre la que establecer un discurso histórico de cada caso de estudio. - Comparar y relacionar las técnicas constructivas empleadas en estas fortalezas con los utilizados en el mismo ámbito temporal. - Difundir para su debate los resultados de la investigación por los foros científicos habituales. El método empleado combina los trabajos de gabinete con una intensa labor de campo, en la que se han documentado cincuenta fortificaciones y se han redactado sus correspondientes fichas de toma de datos. La recopilación de datos se ha incluido en una base de datos que incluye aspectos generales, tipológicos, constructivos y bibliográficos básicos del conjunto, a modo de inventario, de fortificaciones de la provincia. Las fortificaciones seleccionadas se agrupan según una clasificación tipológica y constructiva que marca las líneas de estudio posteriores. Se desarrolla un capítulo de antecedentes en el que se estudia la historia de la construcción fortificada medieval tanto en Europa como en España analizando la evolución de los tipos arquitectónicos y las múltiples influencias culturales que surcaron el Mediterráneo desde el Oriente cruzado e islámico al Poniente donde se desarrollaba la empresa reconquistadora que mantuvo en estado de guerra continuo a la Península Ibérica durante ochocientos años. El análisis del territorio como contenedor del hecho fortificado revela que hay una relación íntima entre la ubicación de las fortificaciones y las formas naturales que definen las vías de comunicación entre los valles del Duero, del Ebro y del Tajo. En efecto, el ámbito de estudio ha supuesto desde la Antigüedad un territorio de paso fundamental en la articulación de las comunicaciones en la Península Ibérica. Este carácter de paso más que de frontera explica las inquietudes y la preocupación por su control tanto por Roma como por el califato cordobés como por los reinos cristianos medievales. El análisis de los elementos históricos se complementa con el estudio detallado de los enfrentamientos fronterizos entre Castilla y Aragón así como los aspectos sociales y políticos que provocaron la fortificación como sistema de definición de la frontera y de organización espacial, jurisdiccional, social y administrativa del territorio. La arquitectura fortificada es esencialmente funcional: su cometido es la defensa. En este sentido, tras un estudio morfológico de los castillos seleccionados se realiza un extenso análisis poliorcético de sus elementos, investigando su origen y aplicación para servir también de parámetros de datación. Siendo el objeto inaugural de la tesis el estudio de los fundamentos constructivos, se explican los distintos materiales de construcción empleados y se agrupan las fábricas de las fortificaciones seleccionadas en dos grandes grupos constructivos: las fábricas aparejadas y las fábricas encofradas. Se han destacado y estudiado la evolución histórica y la tipología y mensiología constructiva de tres técnicas destacadas: el uso del ladrillo, la tapia de cal y canto o mampostería encofrada y la tapia de tierra. Para el estudio de la componente histórica y de la dimensión constructiva de cada técnica ha sido necesario documentar numerosos casos tanto en el ámbito de estudio como en la Península Ibérica con el fin de establecer grupos cronotipológicos constructivos entre los que poder ubicar las fábricas de estas técnicas presentes en el ámbito de estudio. Se ha observado una evolución dimensional de las fábricas de tapia que es más evidente en las hispanomusulmanas al modularse en codos pero que también se advierte significativamente en las cristianas bajomedievales. De cada una de las técnicas analizadas se ha seleccionado un caso de estudio singular y representativo. El castillo de Arcos de Jalón es un ejemplo significativo del empleo de la fábrica mixta de mampostería con verdugadas de ladrillo, así como las murallas de la ciudad fortificada de Peñalcázar lo es de la fábrica de mampostería encofrada y el castillo de Serón de Nágima constituye un caso característico y principal de la utilización de la tapia de tierra en la arquitectura militar bajomedieval. Cada uno de estos tres casos de estudios se examina bajo los mismos cuatro niveles anteriormente mencionados: territorial, histórico, arquitectónico y defensivo y constructivo. El sistemático método de estudio ha facilitado el orden en la investigación y la obtención de unos resultados y conclusiones que verifican la hipótesis y cumplen los objetivos marcados al comienzo. Se ha revisado la datación en la construcción de las fortificaciones analizadas mediante el estudio cronotipológico de sus fábricas, pudiendo trasladarse el método a otros sistemas fortificados. La tesis abre, finalmente, dos vías principales de investigación encaminadas a completar el estudio del sistema fortificado fronterizo bajomedieval en la raya oriental soriana de Castilla: la caracterización y datación por métodos físico-químicos de las muestras de piezas de madera de construcción que se conservan embebidas en las fábricas y la búsqueda documental y archivística que pueda revelar nuevos datos respecto a la fundación, reparación, venta o cualquier aspecto económico, legislativo, organizativo o administrativo relativo a las fortificaciones en documentos coetáneos. ABSTRACT The doctoral thesis develops an original research, held in the field of the Construction History, about the constructive reason of the frontier fortifications in the Late Middle Age between the Crowns of Castile and Aragón in the actual province of Soria, Spain. In the title is expressed the main objective, and also the temporal scope —from the reconquest in the 12th Century by Alfonso the First of Aragón to the unification under the common kingdom of the Catholic Kings— and the territorial extension that the research delimits: those Castilian regions in the border with Aragón in the actual province of Soria. During this period, a series of border wars were been, and this is the reason for the fortification of the border line and the main roads between both Crowns. The lack of studies of these fortifications as participants in a fortified system is the justification of the research. There is several analysis levels: territorial, historical, architectonic, defensive and constructive. Likewise, there is a lack of strictness and inaccuracy in the constructive items in the publications about several fortifications of this study field. This aspect has caused mistakes in the dating because there is neither artistic nor stylistic elements which determines a epoch. The traditionally accepted datings are challenged. An hypothesis is formulated: in the absence of artistic or stylistic elements in a sober and functional buildings is possible to date the time of construction with sufficiently approximation based on construction criteria once formed a cronotypologic classification of each building technique. The hypothesis, therefore, propose a main aim: the study of the constructive reason of the fortified border system. This aim is developed in a series of specifically targets whose achievement programs the analysis levels: - To know and to detail the historical elements which started the wars between Castile and Aragon and its development using historiographical tools, and to analyze the natural characteristic of the territory through cartographical tools. - To understand and to analyze the different architectural types and the building traditions employed in the military buildings in the time researched. - To locate, to document, and to select for their analysis the fortresses and military constructions erected during these border wars in the actual province of Soria through fieldwork and bibliographical and cartographical methods. - To conduct a general study on the fortified system in territorial scale. - To research the architectural, constructive and defensive typology of the system of these border late medieval fortifications. - To analyze the construction logic of the selected case studies and to characterize in the items of material, elements, systems and construction processes. - To sort scattered historical information and to correct mistakes to make a base by which to establish a historic speech of each case study. - To compare and to relate the construction techniques employed in these fortresses with those used in the same time range . - To spread for discussion the research results in the usual scientists forums. The method combines the destock work with an intense fieldwork. Fifty fortifications have been documented and it has written their corresponding data collection card. Data collection has been included in a database that includes general aspects, typological, constructive and basic bibliographical data, as an inventory of fortifications in the province. The selected fortifications are grouped according to a typological and constructive classification which lead the lines of the later study. There is a chapter for the antecedents in which the history of the medieval fortified construction in Europe and in Spain is studied by analyzing the evolution of architectural types and the many cultural influences along the opposite seasides of the Mediterranean Sea, from the Islamic and Crusader East to the Iberian Peninsula in where there were a long and continuous war during eight hundred years. The territory is analyzed as a container of fortifications. This analysis reveals that there is an intimate relationship between the location of the fortifications and the natural forms that define the communication roads between the Duero, Ebro and Tajo valleys. Indeed, the study area has been a cross-territory from ancient times more than a frontierterritory. This communication character explains the concerns about its control both by Rome and by the Muslims of Córdoba as medieval Christian kingdoms. The analysis of historical elements is supplemented by detailed study of border war between Castile and Aragon and the social and political issues that led to the fortification as border definition system and spatial, jurisdictional, social and administrative planning. The fortified architecture is essentially functional: it is responsible for defense. In this sense, after a morphological study of selected castles is performed an extensive analysis of its defensive elements, investigating its origin and application. This analisis serves for the definition of parameters for dating. The purpose of the thesis is the study of the constructive logic. First, various building materials are explained. Then, masonry is grouped into two major constructive groups: rigged masonry and formwork masonry. The historical evolution and the constructive typology and mensiology are studied for each one of the three main techniques: the use of brickwork, the mortar wall and rammed-earth. Many case studies have been documented along the Iberian Peninsula and also in the study area. As conclusion, there is a dimensional evolution of the rammed-earth walls. This evolution is more evident into the Muslim masonry than in the late medieval walls: the reason is the use of the cubit as module. From each of the techniques discussed, a singular and representative case of study has been selected. The castle of Arcos de Jalon is a significant example of mix masonry of stone and brick rows. The walled city of Peñalcázar is built with masonry formwork. Serón de Nágima castle, at last, is a typical and main case of the use of the rammedearth wall of late medieval military architecture. Each of these three case studies were examined under the same four analysis levels above mentioned: territorial, historical, architectural and defensive and constructive. The systematic method of study has facilitated the order in the research and the obtaining of results and conclusions that verify the hypotheses and achieve the research objectives. Dating of the fortifications construction has been revised by studying the cronotypological issues of its masonry. The method can be transferred to the study of other fortified systems. Finally, the thesis describes two main research new ways aimed at completing the study of the late medieval fortified border of Castile in the actual province of Soria. The first of them is the characterization and datig by physicochemical methods the sample pieces of wood construction preserved embedded in the masonry. The second research way is the investigation of the documents in archives that may reveal new information about the foundation, repair, sale or any aspect to economic, legal, organizational or administrative concerning fortifications in contemporary documents.

Houses built from accommodating cabins

The current economic crisis has meant, particularly in Spain, the almost cessation of new buildings construction. This deep crisis will mean in future an irreversible change in the Spanish construction model, based to date almost exclusively on the brick. After focusing on the Spanish property boom and examining its impact on the concept of housing (in a few years the house has moved forward from being contemplated exclusively as a primary good to be also considered a capital asset), we analyse the influence that this transformation has had on architecture (housing typology, building methods, the architectural profession and the architect training) and offers architectural alternatives –trough the university– to the present crisis. The project “Houses built from accommodating cabins” is part of a larger research within the line “Modular Architecture” developed by the Research Group “Design and Industrial Production”, belonging to the Technical University of Madrid, which aims to respond to the need for decent housing at an affordable price, by offering through Internet the plans, resources and other technical details required to build a house oneself. The proposed houses are built from the combination of industrially made modules (accommodation cabins, which are prefabricated modules usually used as provisional constructions in conventional building works), prefabricated subsystems and other catalogue components available on the market, all they set together by dry joints.

Influencia de las condiciones de ejecución en la resistencia de anclajes en convencional y autocompactante

A través de los años las estructuras de hormigón armado han ido aumentando su cuota de mercado, sustituyendo a las estructuras de fábrica de piedra o ladrillo y restándole participación a las estructuras metálicas. Uno de los primeros problemas que surgieron al ejecutar las estructuras de hormigón armado, era cómo conectar una fase de una estructura de este tipo a una fase posterior o a una modificación posterior. Hasta los años 80-90 las conexiones de una fase de una estructura de hormigón armado, con otra posterior se hacían dejando en la primera fase placas de acero con garrotas embebidas en el hormigón fresco o barras grifadas recubiertas de poliestireno expandido. Una vez endurecido el hormigón se podían conectar nuevas barras, para la siguiente fase mediante soldadura a la placa de la superficie o enderezando las barras grifadas, para embeberlas en el hormigón fresco de la fase siguiente. Estos sistemas requerían conocer la existencia y alcance de la fase posterior antes de hormigonar la fase previa. Además requerían un replanteo muy exacto y complejo de los elementos de conexión. Otro problema existente en las estructuras de hormigón era la adherencia de un hormigón fresco a un hormigón endurecido previamente, ya que la superficie de contacto de ambos hormigones suponía un punto débil, con una adherencia baja. A partir de los años 80, la industria química de la construcción experimentó un gran avance en el desarrollo de productos capaces de generar una buena adherencia sobre el hormigón endurecido. Este avance tecnológico tenía aplicación tanto en la adherencia del hormigón fresco sobre el hormigón endurecido, como en la adherencia de barras post-instaladas en agujeros de hormigón endurecido. Este sistema se denominó “anclajes adherentes de barras de acero en hormigón endurecido”. La forma genérica de ejecutarlos es hacer una perforación cilíndrica en el soporte de hormigón, con una herramienta especifica como un taladro, limpiar la perforación, llenarla del material adherente y finalmente introducir la barra de acero. Los anclajes adherentes se dividen en anclajes cementosos y anclajes químicos, siendo estos últimos los más habituales, fiables, resistentes y fáciles de ejecutar. El uso del anclaje adherente de barras de acero en hormigón endurecido se ha extendido por todo el espectro productivo, siendo muy habitual tanto en construcción de obras de hormigón armado de obra civil y edificación, como en obras industriales, instalaciones o fijación de elementos. La ejecución de un anclaje de una barra de acero en hormigón endurecido depende de numerosas variables, que en su conjunto, o de forma aislada pueden afectar de forma notable a la resistencia del anclaje. Nos referimos a variables de los anclajes, que a menudo no se consideran tales como la dirección de la perforación, la máquina de perforación y el útil de perforación utilizado, la diferencia de diámetros entre el diámetro del taladro y la barra, el tipo de material de anclaje, la limpieza del taladro, la humedad del soporte, la altura del taladro, etc. La utilización en los últimos años de los hormigones Autocompactables, añade una variable adicional, que hasta ahora apenas ha sido estudiada. En línea con lo apuntado, la presente tesis doctoral tiene como objetivo principal el estudio de las condiciones de ejecución en la resistencia de los anclajes en hormigón convencional y autocompactable. Esta investigación se centra principalmente en la evaluación de la influencia de una serie de variables sobre la resistencia de los anclajes, tanto en hormigón convencional como en un hormigón autocompactable. Para este estudio ha sido necesaria la fabricación de dos soportes de hormigón sobre los cuales desarrollar los ensayos. Uno de los bloques se ha fabricado con hormigón convencional y el otro con hormigón autocompactable. En cada pieza de hormigón se han realizado 174 anclajes con barras de acero, variando los parámetros a estudiar, para obtener resultados de todas las variables consideradas. Los ensayos a realizar en ambos bloques son exactamente iguales, para poder comparar la diferencia entre un anclaje en un soporte de hormigón con vibrado convencional (HVC) y un hormigón autocompactante (HAC). De cada tipo de ensayo deseado se harán dos repeticiones en la misma pieza. El ensayo de arrancamiento de las barras se realizara con un gato hidráulico hueco, con un sistema de instrumentación de lectura y registro de datos en tiempo real. El análisis de los resultados, realizado con una potente herramienta estadística, ha permitido determinar y evaluar numéricamente la influencia de los variables consideradas en la resistencia de los anclajes realizados. Así mismo ha permitido diferenciar los resultados obtenidos en los hormigones convencionales y autocompactantes, tanto desde el punto de vista de la resistencia mecánica, como de las deformaciones sufridas en el arrancamiento. Se define la resistencia mecánica de un anclaje, como la fuerza desarrollada en la dirección de la barra, para hacer su arrancamiento del soporte. De la misma forma se considera desplazamiento, a la separación entre un punto fijo de la barra y otro del soporte, en la dirección de la barra. Dichos puntos se determinan cuando se ha terminado el anclaje, en la intersección de la superficie plana del soporte, con la barra. Las conclusiones obtenidas han permitido establecer qué variables afectan a la ejecución de los anclajes y en qué cuantía lo hacen, así como determinar la diferencia entre los anclajes en hormigón vibrado convencional y hormigón autocompactante, con resultados muy interesantes, que permiten valorar la influencia de dichas variables. Dentro de las conclusiones podemos destacar tres grupos, que denominaremos como de alta influencia, baja influencia y sin influencia. En todos los casos hay que hacer el estudio en términos de carga y de desplazamiento. Podemos considerar como de alta influencia, en términos de carga las variables de máquina de perforación y el material de anclaje. En términos de desplazamiento podemos considerar de alta influencia además de la máquina de perforación y el material de anclaje, el diámetro del taladro, así como la limpieza y humedad del soporte. Podemos considerar de baja influencia, en términos de carga las variables de tipo de hormigón, dirección de perforación, limpieza y humedad del soporte. En términos de desplazamiento podemos considerar de baja influencia el tipo de hormigón y la dirección de perforación. Podemos considerar en el apartado de “sin influencia”, en términos de carga las variables de diámetro de perforación y altura del taladro. En términos de desplazamiento podemos considerar como “sin influencia” la variable de altura del taladro. Podemos afirmar que las diferencias entre los valores de carga aumentan de forma muy importante en términos de desplazamiento. ABSTRACT Over the years the concrete structures have been increasing their market share, replacing the masonry structures of stone or brick and subtracting as well the participation of the metallic structures. One of the first problems encountered in the implementing of the reinforced concrete structures was connecting a phase structure of this type at a later stage or a subsequent amendment. Until the 80s and 90s the connections of one phase of a reinforced concrete structure with a subsequent first phase were done by leaving the steel plates embedded in the fresh concrete using hooks or bent bars coated with expanded polystyrene. Once the concrete had hardened new bars could be connected to the next stage by welding them to the surface plate or by straightening the bent bars to embed them in the fresh concrete of the next phase. These systems required a previous knowledge of the existence and scope of the subsequent phase before concreting the previous one. They also required a very precise and complex rethinking of the connecting elements. Another existing problem in the concrete structures was the adhesion of a fresh concrete to a previously hardened concrete, since the contact surface of both concretes leaded to a weak point with low adherence. Since the 80s, the chemicals construction industry experienced a breakthrough in the development of products that generate a good grip on the concrete. This technological advance had its application both in the grip on one hardened fresh concrete and in the adhesion of bar post-installed in holes of hardened concrete. This system was termed as adherent anchors of steel bars in hardened concrete. The generic way of executing this system is by firstly drilling a cylindrical hole in the concrete support using a specific tool such as a drill. Then, cleaning the bore and filling it with bonding material to lastly, introduce the steel bar. These adherent anchors are divided into cement and chemical anchors, the latter being the most common, reliable, durable and easy to run. The use of adhesive anchor of steel bars in hardened concrete has spread across the production spectrum turning itself into a very common solution in both construction of reinforced concrete civil engineering and construction, and industrial works, installations and fixing elements as well. The execution of an anchor of a steel bar in hardened concrete depends on numerous variables which together or as a single solution may significantly affect the strength of the anchor. We are referring to variables of anchors which are often not considered, such as the diameter difference between the rod and the bore, the drilling system, cleansing of the drill, type of anchor material, the moisture of the substrate, the direction of the drill, the drill’s height, etc. During recent years, the emergence of self-compacting concrete adds an additional variable which has hardly been studied so far. According to mentioned this thesis aims to study the main performance conditions in the resistance of conventional and self-compacting concrete anchors. This research is primarily focused on the evaluation of the influence of several variables on the strength of the anchoring, both in conventional concrete and self-compacting concrete. In order to complete this study it has been required the manufacture of two concrete supports on which to develop the tests. One of the blocks has been manufactured with conventional concrete and the other with self-compacting concrete. A total of 174 steel bar anchors have been made in each one of the concrete pieces varying the studied parameters in order to obtain results for all variables considered. The tests to be performed on both blocks are exactly the same in order to compare the difference between an anchor on a stand with vibrated concrete (HVC) and a self-compacting concrete (SCC). Each type of test required two repetitions in the same piece. The pulling test of the bars was made with a hollow jack and with an instrumentation system for reading and recording data in real time. The use of a powerful statistical tool in the analysis of the results allowed to numerically determine and evaluate the influence of the variables considered in the resistance of the anchors made. It has likewise enabled to differentiate the results obtained in the self-compacting and conventional concretes, from both the outlook of the mechanical strength and the deformations undergone by uprooting. The mechanical strength of an anchor is defined as the strength undergone in a direction of the bar to uproot it from the support. Likewise, the movement is defined as the separation between a fixed point of the bar and a fixed point from the support considering the direction of the bar. These points are only determined once the anchor is finished, with the bar, at the intersection in the flat surface of the support. The conclusions obtained have established which variables affect the execution of the anchors and in what quantity. They have also permitted to determine the difference between the anchors in vibrated concrete and selfcompacting concrete with very interesting results that also allow to assess the influence of these mentioned variables. Three groups are highlighted among the conclusions called high influence, low influence and no influence. In every case is necessary to perform the study in terms of loading and movement. In terms of loading, there are considered as high influence two variables: drilling machinery and anchorage material. In terms of movement, there are considered as high influence the drilling diameter and the cleaning and moisture of the support, besides the drilling machinery and the anchorage material. Variables such as type of concrete, drilling direction and cleaning and moisture of the support are considered of low influence in terms of load. In terms of movement, the type of concrete and the direction of the drilling are considered variables of low influence. Within the no influence section in terms of loading, there are included the diameter of the drilling and the height of the drill. In terms of loading, the height of the drill is considered as a no influence variable. We can affirm that the differences among the loading values increase significantly in terms of movement.

Study for the rehabilitation of vernacular architecture with sustainable criteria

This paper assesses rural vernacular heritage established in a warm temperate climate, with dry, hot summer, in São Vicente e Ventosa (SVV), Alentejo, Portugal, and takes part in a larger investigation intending to create rehabilitation guidelines, with sustainable criteria and integration of recent technologies, to improving indoor comfort, and revert the state of deterioration. To further reach this aim, this paper proposes a four phases methodology: data collection, evaluation, simulation and development; a first survey data analysis, including climate data and the adapted comfort climograph and isopleth diagram, allows an understanding of thermal comfort and main constraints in site, as well as suitable bioclimatic strategies for SVV: high thermal inertia for tempering extreme summer conditions and the considerable temperature amplitudes throughout the year, complementarily night ventilation for passive cooling, small-sized window openings and movable shading systems for solar radiation protection. An efficient behaviour in stabilizing indoor temperature swings is revealed.

Modeling sub-threshold slope and DIBL mismatch of sub-22nm FinFet

A great challenge for future information technologies is building reliable systems on top of unreliable components. Parameters of modern and future technology devices are affected by severe levels of process variability and devices will degrade and even fail during the normal lifeDme of the chip due to aging mechanisms. These extreme levels of variability are caused by the high device miniaturizaDon and the random placement of individual atoms. Variability is considered a "red brick" by the InternaDonal Technology Roadmap for Semiconductors. The session is devoted to this topic presenDng research experiences from the Spanish Network on Variability called VARIABLES. In this session a talk entlited "Modeling sub-threshold slope and DIBL mismatch of sub-22nm FinFet" was presented.

New designs of the ceramic bricks of horizontal hexagonal hollow

This article is intended to state that Technical Drawing is a multiple tool of expression and communication essential to develop inquiry processes, the scientifically basis and comprehension of drawings and technological designs that can be manufactured. We demonstrate graphically and analytically that spatial vision and graphic thinking allow us to identify graphically real life problems, develop proposals of solutions to be analysed from different points of view, plan and develop the project, provide information needed to make decisions on objects and technological processes. From the knowledge of Technical Drawing and CAD tools we have developed graphic analyses to improve and optimize our proposed modification of the geometry of the rectangular cells of conventional bricks by hexagonal cells, which is protected by a Spanish patent owned by the Polytechnic University of Madrid. This new internal geometry of the bricks will improve the efficiency and the acoustic damping of walls built with the ceramic bricks of horizontal hollow, maintaining the same size of the conventional bricks, without increasing costs either in the manufacture and the sale. A single brick will achieve the width equivalent to more than FOUR conventional bricks.

Variabilidade espacial de uma cultura de milho (Zea mays): influência da distribuiçao vertical de semente

Com o objetivo de estudar a influência da distribuição vertical de semente na variabilidade espacial da implantação de uma cultura de milho em diferentes sistemas de preparação do solo (mobilização convencional, mobilização mínima e sementeira direta), realizaram-se nas campanhas de 2011 e 2012 dois ensaios de campo na região do Alentejo. A avaliação da distribuição vertical de semente fez-se pela determinação da profundidade de sementeira medindo o comprimento do mesocótilo em plântulas de milho. Em sementeira direta foram ainda testadas duas velocidades de trabalho. Os resultados demonstraram que o melhor desempenho de distribuição vertical da semente foi conseguido em sementeira direta com o aumento de velocidade de trabalho de 4 para 6 km h-1 (com um coeficiente de variação, CV, de 10,1%). Uma ANOVA de duplo fator demonstrou que a resistência mecânica do solo e a velocidade de trabalho determinaram diferenças significativas na profundidade de sementeira; a profundidade de sementeira causou diferenças significativas no tempo médio (TME) e percentagem de emergência (PE) da cultura. Os elevados CV observados sugerem a necessidade de uma melhor calibração dos dispositivos de controlo de profundidade dos semeadores por parte dos operadores em campo ou o aperfeiçoamento dos mesmos.