Territorial cohesion impacts of high-speed rail under different zoning systems

Large-scale transport infrastructure projects such as high-speed rail (HSR) produce significant effects on the spatial distribution of accessibility. These effects, commonly known as territorial cohesion effects, are receiving increasing attention in the research literature. However, there is little empirical research into the sensitivity of these cohesion results to methodological issues such as the definition of the limits of the study area or the zoning system. In a previous paper (Ortega et al., 2012), we investigated the influence of scale issues, comparing the cohesion results obtained at four different planning levels. This paper makes an additional contribution to our research with the investigation of the influence of zoning issues. We analyze the extent to which changes in the size of the units of analysis influence the measurement of spatial inequalities. The methodology is tested by application to the Galician (north-western) HSR corridor, with a length of nearly 670 km, included in the Spanish PEIT (Strategic Transport and Infrastructure Plan) 2005-2020. We calculated the accessibility indicators for the Galician HSR corridor and assessed their corresponding territorial distribution. We used five alternative zoning systems depending on the method of data representation used (vector or raster), and the level of detail (cartographic accuracy or cell size). Our results suggest that the choice between a vector-based and raster-based system has important implications. The vector system produces a higher mean accessibility value and a more polarized accessibility distribution than raster systems. The increased pixel size of raster-based systems tends to give rise to higher mean accessibility values and a more balanced accessibility distribution. Our findings strongly encourage spatial analysts to acknowledge that the results of their analyses may vary widely according to the definition of the units of analysis.

Effect of cage type on the behaviour pattern of rabbit does at different physiological stages

Interest in commercially farmed rabbit welfare has increased in recent years. As a result, new alternative housing systems have been developed, although they require evaluation in order to demonstrate their potential for improving welfare. The aim of this trial was to study the behavioural traits of rabbit does housed in 2 different types of cage (TC): conventional vs. alternative with an elevated platform, at different physiological stages (PS); lactation and gestation. Behavioural observations were carried out on 12 rabbit commercial does using continuous 24 h video recording. Independently of PS and TC, rabbit does spent most of their time on foot mats (on av. 57.7%). However, due to the use of platforms (on av. 23.0% of time), lactating does spent 36.6% less time on foot mats (P<0.001) and gestating does spent 27.0% less time on wire mesh (P<0.001) in alternative cages than in conventional cages. Alternative cages allowed for standing posture, but this behaviour was only observed in gestating does (on av. 4.6 times a day). Frequency of drinking was higher in conventional than in alternative cages (24.6 vs. 19.1 times a day; P<0.05). Gestating does housed in conventional cages reached the highest duration and frequency of interacting with neighbours (276 s/d and 4.6 times/d; P<0.05). The frequency of interacting with kits was lower in alternative than in conventional cages (2.4 vs. 8.6 times a day; P<0.01). Doe behaviour was influenced by the time of day, with less activity during the midday hours. During dark hours, rabbit does more frequently performed restless behaviour such as hyperactivity or nursing, matching the time at which rabbit does spent more time on the platform. The platform was frequently used by rabbit does, regardless of their physiological stage, and during late lactation phase, when mothers were not receptive to nursing, does housed in alternative cages used the platform as a mean to flee from kits trying to suckle. Use of the platform might lead to hygienic problems due to retained faeces on the platform and faeces and urine falling onto animals located in the lower part of the cage. The absence of stereotypies in rabbit does of this trial, suggested that animal welfare was not compromised by the type of housing (conventional or alternative cages).

Análisis del rendimiento académico del alumnado de último curso de ingeniería mediante nuevas tecnologías en el proceso de enseñanza‐aprendizaje

En el marco del Espacio Europeo de Educación Superior los estudios deben de estar orientados a facilitar la movilidad de los futuros egresados para que su inclusión en mundo laboral sea global y en este contexto, los sistemas educativos deben introducir cambios en el proceso de enseñanza – aprendizaje y en la gestión. Como uno de los elementos básicos de la creación del EEES es el aprendizaje a lo largo de la vida, se deben adoptar metodologías que doten al estudiante de capacidades para poder enfrentarse a todos los retos de la vida laboral. A través de la presente investigación se trata de aportar una visión real de la aplicación efectiva de un modelo de Aprendizaje Basado en Problemas y el Método del Caso acompañados de una fuerte Acción Tutorial y el uso de la Tecnología de la Información y Comunicación en la Universidad (TIC). Se considera asimismo de gran interés para la mejora del aprendizaje conocer cuál es la opinión real de los estudiantes universitarios, ya que son los principales implicados en relación a un modelo formativo apoyado en el Aprendizaje Basado en Problemas, el Método del Caso, la Acción Tutorial y utilización de las TIC. A través de este estudio se pretende comprobar y valorar cual es la visión real que los alumnos tienen de estas aplicaciones y como las utilizan. Para ello durante los últimos cursos se ha trabajado con alumnos de los últimos cursos de la Escuela Técnica Superior de Ingeniería Civil de la Universidad Politécnica de Madrid aplicando técnicas de Aprendizaje Basado en Problemas y el Método del Caso conjuntamente con la utilización de un Modelo de Acción Tutorial y el uso de la TIC. La tarea se ha centrado en desarrollar, a lo largo de los cursos 2009-10, 2010-11, 2011-12 y 2013-14, un modelo de Acción Tutorial con los alumnos matriculados en las asignaturas de Caminos I, Caminos II, Aforos y Ordenación del Tráfico, asignaturas de la titulación de Ingeniería Técnica de Obras Públicas, y por otro lado, en la asignatura de Caminos, perteneciente a la titulación de Ingeniería Civil. Mediante cuestionarios al inicio y final del curso, se ha conocido cuál es la opinión que poseen los alumnos sobre esta acción. A continuación, durante los cursos 2010-11, 2011-12 y 2013-14 se desarrolla un modelo experimental para evaluar las mejoras, tanto de rendimiento como de adquisición de competencias, utilizando el Aprendizaje Basado en Problemas y el Método del Caso acompañados de las TIC en el proceso de enseñanza–aprendizaje como modelo de Acción Tutorial con alumnos. ABSTRACT Abstract In the frame of the European Higher Education Area, the studies must be faced to facilitate mobility of future graduates for inclusion in the workplace is global and in this context, educational systems must introduce changes in the process of education-learning and management. Since one of the basic elements of the creation of the EHEA is learning throughout life, there must be adopted methodologies that provide the student of aptitudes to be able to face all the challenges of the labor life. Through this research it is provided a real vision of the effective application of a Model of Learning Based on Problems and the Case Method accompanied by a strong Tutorial Action and the use of ITC in the University. It is also considered of great interest for the improvement of learning to know what the real opinion of the college students is, as they are the main players in relation in a training model based on Problem-Based Learning, the Case Method, the Tutorial Action and Use of ICT. Through this study it is expected to verify and assess which is the real vision that students have about these applications and how they use them. In order to achieve the goal of this research project, during the last three years I have been working with students of last courses of the Civil Engineering School of the Technical University of Madrid applying with them techniques of Problem-Based Learning and the Case Method together with the use of a Model Action Tutorial and the Use of Information Technology and Communication (ICT). The task has focused on developing, over the 2009-10, 2010-11, 2011-12 and 2013-14 courses, a model of Tutorial Action with students enrolled in the subjects of Roads I, Roads II, Traffic Gauging and Traffic Management, all of them of the old degree in Civil Engineering (1971 Study Plan), and secondly, on the subject of Roads which belong to the current degree of Civil Engineering. Using questionnaires at the beginning and end of the course the perception that students have on this action.. Then, during the 2010-11, 2011-12 and 2013-14 courses an experimental model is developed to evaluate improvements in both performance and skills acquisition, using Problem-Based Learning and the Case Method together with the ICT in Teaching-Learning Pprocess as a model of Tutorial Action with students.

Validación de sistemas constructivos de los cerramientos de la edificación mediante la aplicación de los métodos de decisión multicriterio : aplicación al catálogo de elementos constructivos del Código Técnico de la Edificación

Como punto de partida para el desarrollo de la Tesis, se mantiene la hipótesis de que es posible establecer métodos de evaluación global sobre el grado de utilidad de los sistemas constructivos correspondientes a los cerramientos de la edificación. Tales métodos habrían de posibilitar, de entre una serie finita de sistemas alternativos, cuáles de ellos son los objetivamente más adecuados para su selección en un entorno de decisión concreto, y habrían de permitir fundamentar la justificación objetiva de tal decisión. Paralelamente a esta hipótesis de carácter general, se planteó desde el inicio la necesidad de comprobación de una hipótesis de partida particular según la cual los sistemas constructivos basados en la utilización de componentes prefabricados, o procesos de puesta en obra con un alto grado de industrialización arrojarían valores de utilidad mayores que los sistemas tradicionales basados en la albañilería. Para la verificación de estas dos hipótesis de partida se ha procedido inicialmente a la selección de un conjunto coherente de doce sistemas de cerramientos de la edificación que pudiese servir como testigo de su diversidad potencial, para proceder a su valoración comparativa. El método de valoración propuesto ha entrado a considerar una serie de factores de diversa índole que no son reducibles a un único parámetro o magnitud que permitiese una valoración de tipo lineal sobre su idoneidad relativa, ni que permitiese establecer un grado de prelación entre los distintos sistemas constructivos alternativos de manera absoluta. Para resolver este tour de force o desafío metodológico se ha acudido a la aplicación de metodologías de valoración que nos permitiesen establecer de forma racional dicha comparativa. Nos referimos a una serie de metodologías provenientes en primera instancia de las ciencias exactas, que reciben la denominación de métodos de ayuda a la decisión multicriterio, y en concreto el denominado método ELECTRE. Inicialmente, se ha planteado la aplicación del método de análisis sobre doce sistemas constructivos seleccionados de tal forma que representasen de forma adecuada las tres categorías establecidas para caracterizar la totalidad de sistemas constructivos posibles; por peso, grado de prefabricación y grado de ventilación. Si bien la combinación de las tres categorías básicas anteriormente señaladas produce un total de 18 subcategorías conceptuales, tomamos finalmente doce subcategorías dado que consideramos que es un número operativo suficiente por extenso para el análisis propuesto y elimina tipos no relevantes. Aplicado el método propuesto, a estos doce sistemas constructivos “testigo”, se constata el mayor grado de utilidad de los sistemas prefabricados, pesados y no ventilados. Al hilo del análisis realizado en la Parte II de la Tesis sobre los doce sistemas constructivos “testigo”, se ha realizado un volcado de los sistemas constructivos incluidos en el Catalogo de Elementos Constructivos del CTE (versión 2010) sobre las dieciocho subcategorías definidas en dicha Parte II para caracterizar los sistemas constructivos “testigo”. Posteriormente, se ha procedido a una parametrización de la totalidad de sistemas constructivos para cerramientos de fachadas incluidos en este Catálogo. La parametrización sistemática realizada ha permitido establecer, mediante el cálculo del valor medio que adoptan los parámetros de los sistemas pertenecientes a una misma familia de las establecidas por el Catálogo, una caracterización comparativa del grado de utilidad de dichas familias, tanto en lo relativo a cada uno de los parámetros como en una valoración global de sus valores, de carácter indicativo. Una vez realizada una parametrización completa de la totalidad de sistemas constructivos incluidos en el Catálogo, se ha realizado una simulación de aplicación de la metodología de validación desarrollada en la Parte II de la presente Tesis, con el objeto de comprobar su adecuación al caso. En conclusión, el desarrollo de una herramienta de apoyo a la decisión multicriterio aplicada al Catálogo de Elementos constructivos del CTE se ha demostrado técnicamente viable y arroja resultados significativos. Se han diseñado dos sistemas constructivos mediante la aplicación de la herramienta desarrollada, uno de fachada no ventilada y otro de fachada ventilada. Comparados estos dos sistemas constructivos mejorados con otros sistemas constructivos analizados Se comprueba el alto grado de utilidad objetiva de los dos sistemas diseñados en relación con el resto. La realización de este ejercicio de diseño de un sistema constructivo específico, que responde a los requerimientos de un decisor concreto viene a demostrar, así pues, la utilidad del algoritmo propuesto en su aplicación a los procesos de diseño de los sistemas constructivos. La tesis incorpora dos innovaciones metodológicas y tres innovaciones instrumentales. ABSTRACT The starting point for the thesis is the hypothesis that it is possible to devise suitability degree evaluation methods of building enclosure systems. Such methods should allow optimizing appraisal, given a specific domain of decision, among a finite number of alternative systems, and provide objective justification of such decision. Along with the above mentioned general assumption, a second hypothesis whereby constructive systems based on the use of prefabricated components, or high industrialization degree work processes, would throw efficiency values higher than traditional masonry systems needed to be tested. In order to validate these two hypothesis a coherent set of twelve enclosure systems that could serve as a reference sample of their potential diversity was selected and a comparative evaluation was carried out. The valuation method proposed has considered several different factors that are neither reducible to a single parameter or magnitude that would allow a linear evaluation of their relative suitability nor allow to establishing an absolute priority ranking between different alternative constructive systems. In order to resolve this tour de force or methodological challenge, valuation methodologies that enable use establishing rational assessments were used. We are referring to a number of methodologies taken from the exact sciences field, usually known as aid methods for multi-criteria decision, in particular the so-called ELECTRE method. Even though the combination of the mentioned three basic categories result in eighteen conceptual sub categories, we are finally considering just twelve since we deem it adequately extended for the our intended purpose and eliminates non relevant instances. The method of analysis was initially applied to the set of twelve selected constructive systems is a way that they could represent adequately the three previously established categories set out to characterize all possible enclosure systems, namely weight, prefabrication degree and ventilation degree. Once the proposed method is applied to the sample systems, the higher efficiency of the prefabricated, heavy and not ventilated systems was confirmed. In line with the analysis in Part II of the thesis on the twelve chosen enclosure systems, it has done an uploading data of construction systems listed in the Catalogue of constructive elements of the CTE (version 2010) according the eighteen subcategories used in this part II to characterize the construction systems taken as sample. Subsequently, a parameterization of all enclosure facade systems included in this catalog has been undertaken. The systematic parameterization has allowed to set, by means of calculating the average values of the parameters of the systems belonging to the same family of those established by the Catalog, a comparative characterization of the efficiency degree of these families, both in relation to each parameter as to an overall evaluation of its values, in a indicative way. After the parameterization of all enclosure systems included in the Catalog, a simulation of validation methodology application developed in Part II of this Thesis has been made, in order to assess its consistency to the referred case. In conclusion, the development of a multi-criteria decision aid tool, applied to the CTE Catalog of constructive elements, has proved to be technically feasible and yields significant results. Two building systems through the application of the developed tool, a non-ventilated façade and a ventilated façade have been designed. Comparing these two improved construction systems with other building systems analyzed, we were able to assess the high degree of objective efficiency of the two systems designed in relation to the rest. The exercise of designing a specific enclosure system that meets the requirements of a particular decision-maker hence shows the suitability of the proposed algorithm applied to the process of enclosure systems design. This Thesis includes two methodological innovations and three instrumental innovations.

Evaluating alternative industrial network organizations and information systems

Purpose – The purpose of this paper is to present a simulation‐based evaluation method for the comparison of different organizational forms and software support levels in the field of supply chain management (SCM). Design/methodology/approach – Apart from widely known logistic performance indicators, the discrete event simulation model considers explicitly coordination cost as stemming from iterative administration procedures. Findings - The method is applied to an exemplary supply chain configuration considering various parameter settings. Curiously, additional coordination cost does not always result in improved logistic performance. Influence factor variations lead to different organizational recommendations. The results confirm the high importance of (up to now) disregarded dimensions when evaluating SCM concepts and IT tools. Research limitations/implications – The model is based on simplified product and network structures. Future research shall include more complex, real world configurations. Practical implications – The developed method is designed for the identification of improvement potential when SCM software is employed. Coordination schemes based only on ERP systems are valid alternatives in industrial practice because significant investment IT can be avoided. Therefore, the evaluation of these coordination procedures, in particular the cost due to iterations, is of high managerial interest and the method provides a comprehensive tool for strategic IT decision making. Originality/value – Reviewed literature is mostly focused on the benefits of SCM software implementations. However, ERP system based supply chain coordination is still widespread industrial practice but associated coordination cost has not been addressed by researchers.

Fast Correction of Tiled Display Systems on Planar Surfaces

A method for fast colour and geometric correction of a tiled display system is presented in this paper. Such kind of displays are a common choice for virtual reality applications and simulators, where a high resolution image is required. They are the cheapest and more flexible alternative for large image generation but they require a precise geometric and colour correction. The purpose of the proposed method is to correct the projection system as fast as possible so in case the system needs to be recalibrated it doesn’t interfere with the normal operation of the simulator or virtual reality application. This technique makes use of a single conventional webcam for both geometric and photometric correction. Some previous assumptions are made, like planar projection surface and negligibleintra-projector colour variation and black-offset levels. If these assumptions hold true, geometric and photometric seamlessness can be achievedfor this kind of display systems. The method described in this paper is scalable for an undefined number of projectors and completely automatic.

A prototype from the Solar Decathlon Competition becomes an educational building in sustanaible architecture

In 2008, the City Council of Rivas-Vaciamadrid (Spain) decided to promote the construction of “Rivasecopolis”, a complex of sustainable buildings in which a new prototype of a zero-energy house would become the office of the Energy Agency. According to the initiative of the City Council, it was decided to recreate the dwelling prototype “Magic-box” which entered the 2005 Solar Decathlon Competition. The original project has been adapted to a new necessities programme, by adding the necessary spaces that allows it to work as an office. A team from university has designed and carried out the direction of the construction site. The new Solar House is conceived as a “testing building”. It is going to become the space for attending citizens in all questions about saving energy, energy efficiency and sustainable construction, having a permanent small exhibition space additional to the working places for the information purpose. At the same time, the building includes the use of experimental passive architecture systems and a monitoring and control system. Collected data will be sent to University to allow developing research work about the experimental strategies included in the building. This paper will describe and analyze the experience of transforming a prototype into a real durable building and the benefits for both university and citizens in learning about sustainability with the building

Grid-connected roof solar plants in educational institutions for testing and electricity generation: a case in Spain.

The use of photovoltaic experimental plants in engineering educational buildings contributes to an increase in acceptance of this technology by future engineers. There are some photovoltaic (PV) systems in educational buildings in Spain, but they are usually limited to buildings in relation to electrical technologies or research areas. They are not common in other educational or official buildings. This paper presents the project of a grid-connected solar plant with two main objectives. First, different PV module technologies will be compared. Second, an emphasis on agronomical areas in educational settings will be reviewed in an attempt to facilitate student engagement in the use of the power plant. The system is grid-connected in order to pay-back the investment in the plant. In fact the electricity generated by the plant will be used by the installations of the building, as it is the closest consumer. This work intends to approximate photovoltaic technology to university degrees not directly related with it and at the same time research in comparison of systems with different technologies. This is a good example of an solar plant for both optimum production and educational purposes.

E-learning systems support of collaborative agreements: a theoretical model

This paper introduces a theoretical model for developing integrated degree programmes through e-learning systems as stipulated by a collaboration agreement signed by two universities. We have analysed several collaboration agreements between universities at the national, European, and transatlantic level as well as various e-learning frameworks. A conceptual model, a business model, and the architecture design are presented as part of the theoretical model. The paper presents a way of implementing e-learning systems as a tool to support inter-institutional degree collaborations, from the signing of the collaborative agreement to the implementation of the necessary services. In order to show how the theory can be tested one sample scenario is presented.

Sustainability of irrigated farming systems in a Tunisian region: A recursive stochastic programming analysis

The aim of this study was to evaluate the sustainability of farm irrigation systems in the Cébalat district in northern Tunisia. It addressed the challenging topic of sustainable agriculture through a bio-economic approach linking a biophysical model to an economic optimisation model. A crop growth simulation model (CropSyst) was used to build a database to determine the relationships between agricultural practices, crop yields and environmental effects (salt accumulation in soil and leaching of nitrates) in a context of high climatic variability. The database was then fed into a recursive stochastic model set for a 10-year plan that allowed analysing the effects of cropping patterns on farm income, salt accumulation and nitrate leaching. We assumed that the long-term sustainability of soil productivity might be in conflict with farm profitability in the short-term. Assuming a discount rate of 10% (for the base scenario), the model closely reproduced the current system and allowed to predict the degradation of soil quality due to long-term salt accumulation. The results showed that there was more accumulation of salt in the soil for the base scenario than for the alternative scenario (discount rate of 0%). This result was induced by applying a higher quantity of water per hectare for the alternative as compared to a base scenario. The results also showed that nitrogen leaching is very low for the two discount rates and all climate scenarios. In conclusion, the results show that the difference in farm income between the alternative and base scenarios increases over time to attain 45% after 10 years.

A Satisfaction-based Model for Affect Recognition from Conversational Features in Spoken Dialog Systems

Detecting user affect automatically during real-time conversation is the main challenge towards our greater aim of infusing social intelligence into a natural-language mixed-initiative High-Fidelity (Hi-Fi) audio control spoken dialog agent. In recent years, studies on affect detection from voice have moved on to using realistic, non-acted data, which is subtler. However, it is more challenging to perceive subtler emotions and this is demonstrated in tasks such as labelling and machine prediction. This paper attempts to address part of this challenge by considering the role of user satisfaction ratings and also conversational/dialog features in discriminating contentment and frustration, two types of emotions that are known to be prevalent within spoken human-computer interaction. However, given the laboratory constraints, users might be positively biased when rating the system, indirectly making the reliability of the satisfaction data questionable. Machine learning experiments were conducted on two datasets, users and annotators, which were then compared in order to assess the reliability of these datasets. Our results indicated that standard classifiers were significantly more successful in discriminating the abovementioned emotions and their intensities (reflected by user satisfaction ratings) from annotator data than from user data. These results corroborated that: first, satisfaction data could be used directly as an alternative target variable to model affect, and that they could be predicted exclusively by dialog features. Second, these were only true when trying to predict the abovementioned emotions using annotator?s data, suggesting that user bias does exist in a laboratory-led evaluation.

Implementation techniques for evolvable HW systems: virtual vs. dynamic reconfiguration

Adaptive hardware requires some reconfiguration capabilities. FPGAs with native dynamic partial reconfiguration (DPR) support pose a dilemma for system designers: whether to use native DPR or to build a virtual reconfigurable circuit (VRC) on top of the FPGA which allows selecting alternative functions by a multiplexing scheme. This solution allows much faster reconfiguration, but with higher resource overhead. This paper discusses the advantages of both implementations for a 2D image processing matrix. Results show how higher operating frequency is obtained for the matrix using DPR. However, this is compensated in the VRC during evolution due to the comparatively negligible reconfiguration time. Regarding area, the DPR implementation consumes slightly more resources due to the reconfiguration engine, but adds further more capabilities to the system.

An open-source simulation tool of grid-connected PV systems.

This paper will present an open-source simulation tool, which is being developed in the frame of an European research project1. The tool, whose final version will be freely available through a website, allows the modelling and the design of different types of grid-connected PV systems, such as large grid-connected plants and building-integrated installations. The tool is based on previous software developed by the IES-UPM2, whose models and energy losses scenarios have been validated in the commissioning of PV projects3 carried out in Spain, Portugal, France and Italy, whose aggregated capacity is nearly 300MW. This link between design and commissioning is one of the key points of tool presented here, which is not usually addressed by present commercial software. The tool provides, among other simulation results, the energy yield, the analysis and breakdown of energy losses, and the estimations of financial returns adapted to the legal and financial frameworks of each European country. Besides, educational facilities will be developed and integrated in the tool, not only devoted to learn how to use this software, but also to train the users on the best design PV systems practices. The tool will also include the recommendation of several PV community experts, which have been invited to identify present necessities in the field of PV systems simulation. For example, the possibility of using meteorological forecasts as input data, or modelling the integration of large energy storage systems, such as vanadium redox or lithium-ion batteries. Finally, it is worth mentioning that during the verification and testing stages of this software development, it will be also open to the suggestions received from the different actors of the PV community, such as promoters, installers, consultants, etc.

Incorporating proactivity to context-aware recommender systems for e-learning

Recommender systems in e-learning have proved to be powerful tools to find suitable educational material during the learning experience. But traditional user request-response patterns are still being used to generate these recommendations. By including contextual information derived from the use of ubiquitous learning environments, the possibility of incorporating proactivity to the recommendation process has arisen. In this paper we describe methods to push proactive recommendations to e-learning systems users when the situation is appropriate without being needed their explicit request. As a result, interesting learning objects can be recommended attending to the user?s needs in every situation. The impact of this proactive recommendations generated have been evaluated among teachers and scientists in a real e-learning social network called Virtual Science Hub related to the GLOBAL excursion European project. Outcomes indicate that the methods proposed are valid to generate such kind of recommendations in e-learning scenarios. The results also show that the users' perceived appropriateness of having proactive recommendations is high.

Wide-angle, high-concentration photovoltaics to compete with flat plate systems

A novel photovoltaic concentrator enables highly uniform irradiance on a small number of efficient solar cells. The maximum electrical power of a photovoltaic (PV) energy installation depends on three factors: the available irradiance, the size of the systems collecting sunlight, and the rate at which the device transforms light into electricity (the conversion efficiency). Developers can maximize the irradiance by carefully selecting the site and orientation of the solar facility. But they can only expand their sunlight collection systems for standard flat plate PV devices by increasing the number of solar cells, at greater cost. Here, we consider the advantages of an alternative PV system that produces more energy without increasing the number of cells used (actually, reducing it), by improving the conversion rates.We also present a new device that may enhance the commercial viability of such technologies.