Ion charge number and flux saturation effects in the corona of a laser-irradiated pellet

The quasisteady structure of the corona of a laser-irradiated pellet is completely determined for arbitrary Z, (ion charge number} and re/ra (ratio of critical and ablation radii), and for heat-flux saturation factor/above approximately 0.04. The ion-to-electron temperature ratio at rc grows sensibly with Z,; all other quantities depend weakly and nonmonotonically on Z,. For rc /ra close to unity, and all Z, of interest (Z, < 47}, the flow is subsonic at rc. For a given laser power W, flux saturation may decrease (low/) or increase (high/) the ablation pressure Pa relative to the value obtained when saturation is not considered; in some cases a decrease in/with W fixed increases Pa. For intermediate^ ~0.1), Pa cc (W/r* )2/3 p\n\pc = critical density), independently of rc/ra; for/~0.6, Pa «s larger by a factor of about [rc/raf13. For rjra > 1.2 roughly, the mass ablation rate is C{Z,) [{m/kZ.f^Kr^Pl) l,\ independent of pc and/, and barely dependent on Z,(m, is ion mass; k, Boltzmann's constant; K, conductivity coefficient; and C, a tabulated function).

Prediction of PM10 concentrations using Fuzzy c-Means and ANN

Salamanca has been considered among the most polluted cities in Mexico. The vehicular park, the industry and the emissions produced by agriculture, as well as orography and climatic characteristics have propitiated the increment in pollutant concentration of Particulate Matter less than 10 μg/m3 in diameter (PM10). In this work, a Multilayer Perceptron Neural Network has been used to make the prediction of an hour ahead of pollutant concentration. A database used to train the Neural Network corresponds to historical time series of meteorological variables (wind speed, wind direction, temperature and relative humidity) and air pollutant concentrations of PM10. Before the prediction, Fuzzy c-Means clustering algorithm have been implemented in order to find relationship among pollutant and meteorological variables. These relationship help us to get additional information that will be used for predicting. Our experiments with the proposed system show the importance of this set of meteorological variables on the prediction of PM10 pollutant concentrations and the neural network efficiency. The performance estimation is determined using the Root Mean Square Error (RMSE) and Mean Absolute Error (MAE). The results shown that the information obtained in the clustering step allows a prediction of an hour ahead, with data from past 2 hours

Image sub-segmentation by PFCM and Artificial Neural Networks to detect pore space in 2D and 3D CT soil images

The image by Computed Tomography is a non-invasive alternative for observing soil structures, mainly pore space. The pore space correspond in soil data to empty or free space in the sense that no material is present there but only fluids, the fluid transport depend of pore spaces in soil, for this reason is important identify the regions that correspond to pore zones. In this paper we present a methodology in order to detect pore space and solid soil based on the synergy of the image processing, pattern recognition and artificial intelligence. The mathematical morphology is an image processing technique used for the purpose of image enhancement. In order to find pixels groups with a similar gray level intensity, or more or less homogeneous groups, a novel image sub-segmentation based on a Possibilistic Fuzzy c-Means (PFCM) clustering algorithm was used. The Artificial Neural Networks (ANNs) are very efficient for demanding large scale and generic pattern recognition applications for this reason finally a classifier based on artificial neural network is applied in order to classify soil images in two classes, pore space and solid soil respectively.

Microcalcifications Detection using PFCM and ANN

This work presents a method to detect Microcalcifications in Regions of Interest from digitized mammograms. The method is based mainly on the combination of Image Processing, Pattern Recognition and Artificial Intelligence. The Top-Hat transform is a technique based on mathematical morphology operations that, in this work is used to perform contrast enhancement of microcalcifications in the region of interest. In order to find more or less homogeneous regions in the image, we apply a novel image sub-segmentation technique based on Possibilistic Fuzzy c-Means clustering algorithm. From the original region of interest we extract two window-based features, Mean and Deviation Standard, which will be used in a classifier based on a Artificial Neural Network in order to identify microcalcifications. Our results show that the proposed method is a good alternative in the stage of microcalcifications detection, because this stage is an important part of the early Breast Cancer detection

Stopping of α particles from the core in corona plasmas

In the laser fusion reactor design, the protection of first wall and the final optics from high energy ions is the key issue. So, it is necessary to predict the precise energy spectra of ions.In the previous reactor designs, the ion energy spectra were provided by the classical ion transport codes. However, this poster shows that the α particle spectrum is significantly modified by the anomalous process in ablated plasmas.

Pollutant concentrations and Meteorological data classification by Neural Networks

This paper present an environmental contingency forecasting tool based on Neural Networks (NN). Forecasting tool analyzes every hour and daily Sulphur Dioxide (SO2) concentrations and Meteorological data time series. Pollutant concentrations and meteorological variables are self-organized applying a Self-organizing Map (SOM) NN in different classes. Classes are used in training phase of a General Regression Neural Network (GRNN) classifier to provide an air quality forecast. In this case a time series set obtained from Environmental Monitoring Network (EMN) of the city of Salamanca, Guanajuato, México is used. Results verify the potential of this method versus other statistical classification methods and also variables correlation is solved.

ANN and Fuzzy c-Means applied to environmental pollution prediction

Salamanca, situated in center of Mexico is among the cities which suffer most from the air pollution in Mexico. The vehicular park and the industry, as well as orography and climatic characteristics have propitiated the increment in pollutant concentration of Sulphur Dioxide (SO2). In this work, a Multilayer Perceptron Neural Network has been used to make the prediction of an hour ahead of pollutant concentration. A database used to train the Neural Network corresponds to historical time series of meteorological variables and air pollutant concentrations of SO2. Before the prediction, Fuzzy c-Means and K-means clustering algorithms have been implemented in order to find relationship among pollutant and meteorological variables. Our experiments with the proposed system show the importance of this set of meteorological variables on the prediction of SO2 pollutant concentrations and the neural network efficiency. The performance estimation is determined using the Root Mean Square Error (RMSE) and Mean Absolute Error (MAE). The results showed that the information obtained in the clustering step allows a prediction of an hour ahead, with data from past 2 hours.

Electron temperature versus laser intensity times wavelength squared: a comparison of theory and experiments

The peak temperature in the corona of plasma ejected by a laser-irradiated slab is discussed in terms of a one-electron-temperature model. Both heat-flux saturation and pulse rise-time effects are considered;the intensity in the rising half of the pulse is approximated by a linear function of time, I(t) = Iot/r. The temperature is found to be proportional to (IQX2)273 and a function of I0X4/r. Above a certain value of I0X4/T, the plasma presents two characteristic temperatures (at saturation and at the critical surface) which can be identified with experimentally observed cold- and hot-electron temperatures. The results are compared with extensive experimental data available for both nd and CO2 lasers, I0(W'cnf2) X2 (/um) starting around 1012. The agreement is good if substantial flux inhibition is assumed (flux-limit factor f = 0.03), and fails for I0X2 above 1O1S. Results for both ablation pressure and mass ablation rate are also given.

Macroscopic motion and gravitation in thermodynamics

A series of examples rarely presented to students is discussed to illustrate a property of thermodynamic equilibrium: small parts of a fully isolated system move as if points of a rigid body, so as to minimize the macroscopic (kinetic) energy EM. Most examples lie in the fields of astronomy and astrophysics, EM then including the gravitational energy. The paradoxical behaviour of gravitation, in particular in the extreme case of black holes,is discussed.

Analysis of the influence of the plasma thermodynamic regime in the spectrally resolved and mean radiative opacity calculations of carbon plasmas in a wide range of density and temperature

In this work the spectrally resolved, multigroup and mean radiative opacities of carbon plasmas are calculated for a wide range of plasma conditions which cover situations where corona, local thermodynamic and non-local thermodynamic equilibrium regimes are found. An analysis of the influence of the thermodynamic regime on these magnitudes is also carried out by means of comparisons of the results obtained from collisional-radiative, corona or Saha–Boltzmann equations. All the calculations presented in this work were performed using ABAKO/RAPCAL code.

Teaching art and history to photonics students

The case to be reported in this paper is the teaching of topics involving the relation among Photonics, its history, the international situation and the artistic movements in each period. These kind of new studies correspond to a new tendency in teaching interdisciplinary topics to students coming from different areas. Two main courses, one in History and other one in Art, will be taken as examples. Theses two courses have been taught for several years in Madrid, Spain, for Telecomm students and the results have been very satisfactory

Contribution to active multi-beam reconfigurable antennas for L and S bands

La presente tesis doctoral con título "Contribution to Active Multi-Beam Reconfigurable Antennas for L and S Bands" ha sido desarrollada por el investigador ingeniero de telecomunicación estudiante de doctorado Javier García-Gasco Trujillo en el Grupo de Radiación del Departamento de Señales, Sistemas y Radiocomunicaciones de la ETSI de Telecomunicación de la Universidad Politécnica de Madrid bajo la dirección de los doctores Manuel Sierra Pérez y José Manuel Fernández González. Durante décadas, el desarrollo de antenas de apuntamiento electrónico ha estado limitado al área militar. Su alto coste y su gran complejidad eran los mayores obstáculos que frenaban la introducción de esta tecnología en aplicaciones comerciales de gran escala. La reciente aparición de componentes de estado sólido prácticos, fiables, y de bajo coste ha roto la barrera del coste y ha reducido la complejidad, haciendo que las antenas reconfigurables de apuntamiento electrónico sean una opción viable en un futuro cercano. De esta manera, las antenas phased array podrían llegar a ser la joya de la corona que permitan alcanzar los futuros retos presentes en los sistemas de comunicaciones tanto civiles como militares. Así pues, ahora es el momento de investigar en el desarrollo de antenas de apuntamiento electrónico de bajo coste, donde los nuevos componentes de estado sólido comerciales forman el núcleo duro de la arquitectura. De esta forma, el estudio e implementación de estos arrays de antenas activas de apuntamiento electrónico capaces de controlar la fase y amplitud de las distintas señales implicadas es uno de los grandes retos de nuestro tiempo. Esta tesis se enfrenta a este desafío, proponiendo novedosas redes de apuntamiento electrónico e innovadores módulos de transmisión/recepción (T/R) utilizando componentes de estado sólido de bajo coste, que podrán integrar asequibles antenas activas reconfigurables multihaz en bandas L y S. En la primera parte de la tesis se realiza una descripción del estado del arte de las antenas phased array, incluyendo su base teórica y sus ventajas competitivas. Debido a que las contribuciones obtenidas en la presente tesis han sido realizadas dentro de distintos proyectos de investigación, donde se han manejada antenas de simple/doble polarización circular y simple/doble banda de trabajo, se describen detenidamente los dos proyectos más relevantes de la investigación: el radar de basura espacial de la Agencia Espacial Europea (ESA), Space Situational Awareness (SSA); y la estación base de seguimiento y control de satélites de órbita baja, GEOdesic Dome Array (GEODA). Sin lugar a dudas, los dispositivos desfasadores son uno de los componentes clave en el diseño de antenas phased arrays. Recientemente se ha observado una gran variación en el precio final de estos dispositivos, llegando en ocasiones a límites inasequibles. Así pues, se han propuesto distintas técnicas de conformación de haz alternativas a la utilización de componentes desfasadores comerciales: el desfasador de líneas conmutadas, la red de haz conmutado, y una novedosa red desfasadora divisora/combinadora de potencia. Para mostrar un uso práctico de las mismas, se ha propuesto el uso de las tres alternativas para el caso práctico del subarray de cinco elementos de la celda GEODA-SARAS. Tras dicho estudio se obtiene que la novedosa red desfasadora divisora/combinadora de potencia propuesta es la que mejor relación comportamiento/coste presenta. Para verificar su correcto funcionamiento se construye y mide los dos bloques principales de los que está compuesta la red total, comprobando que en efecto la red responde según lo esperado. La estructura más simple que permite realizar un barrido plano es el array triangular de tres elementos. Se ha realizado el diseño de una nueva red multihaz que es capaz de proporcionar tres haces ortogonales en un ángulo de elevación _0 y un haz adicional en la dirección broadside utilizando el mencionado array triangular de tres elementos como antena. En primer lugar se realizar una breve introducción al estado del arte de las redes clásicas multihaz. Así mismo se comentan innovadores diseños de redes multihaz sin pérdidas. El estudio da paso a las redes disipativas, de tal forma que se analiza su base matemática y se muestran distintas aplicaciones en arrays triangulares de tres elementos. Finalmente, la novedosa red básica propuesta se presenta, mostrando simulaciones y medidas de la misma para el caso prácticoo de GEODA. También se ha diseñado, construido y medido una red compuesta por dos redes básicas complementarias capaz de proporcionar seis haces cuasi-ortogonales en una dirección _0 con dos haces superpuestos en broadside. La red propuesta queda totalmente validada con la fabricación y medida de estos con prototipos. Las cadenas de RF de los módulos T/R de la nueva antena GEODA-SARAS no son algo trivial. Con el fin de mostrar el desarrollo de una cadena compleja con una gran densidad de componentes de estado sólido, se presenta una descripción detallada de los distintos componentes que integran las cadenas de RF tanto en transmisión como en recepción de la nueva antena GEODA-SARAS. Tras presentar las especificaciones de la antena GEODA-SARA y su diagrama de bloques esquemático se describen los dos bloques principales de las cadenas de RF: la celda de cinco elementos, y el módulo de conversión de panel. De la misma manera también se presentará el módulo de calibración integrado dentro de los dos bloques principales. Para comprobar que el funcionamiento esperado de la placa es el adecuado, se realizará un análisis que tratará entre otros datos: la potencia máxima en la entrada del transmisor (comprobando la saturación de la cadena), señal de recepción mínima y máxima (verificando el rango de sensibilidad requerido), y el factor G/T (cumpliendo la especificación necesaria). Así mismo se mostrará un breve estudio del efecto de la cuantificación de la fase en el conformado de haz de RF. Los estudios muestran que la composición de las cadenas de RF permite el cumplimiento de las especificaciones necesarias. Finalmente la tesis muestra las conclusiones globales del trabajo realizado y las líneas futuras a seguir para continuar con esta línea de investigación. ABSTRACT This PhD thesis named "Contribution to Active Multi-Beam Reconfigurable Antennas for L and S Bands", has been written by the Electrical Engineer MSc. researcher Javier García-Gasco Trujillo in the Grupo de Radiación of the Departamento de Señales, Sistemas y Radiocomunicaciones from the ETSI de Telecomunicación of the Universidad Politécnica de Madrid. For decades, the implementation of electronically steerable phased array antennas was confined to the military area. Their high cost and complexity were the major obstacles to introduce this technology in large scale commercial applications. The recent emergence of new practical, low-cost, and highly reliable solid state devices; breaks the barrier of cost and reduces the complexity, making active phased arrays a viable future option. Thus, phased array antennas could be the crown jewel that allow to meet the future challenges in military and civilian communication systems. Now is time to deploy low-cost phased array antennas, where newly commercial components form the core of the architecture. Therefore, the study and implementation of these novel low-cost and highly efficient solid state phased array blocks capable of controlling signal phase/amplitude accurately is one of the great challenges of our time. This thesis faces this challenge, proposing innovative electronic beam steering networks and transmitter/ receiver (T/R) modules using affordable solid state components, which could integrate fair reconfigurable phased array antennas working in L and S bands. In the first part of the thesis, a description of the state of art of phased array antennas, including their fundamentals and their competitive advantages, is presented. Since thesis contributions have been carried out for different research projects, where antennas with single/double circular polarization and single/double working frequency bands have been examined, frameworks of the two more important projects are detailed: the Space Situational Awareness (SSA) programme from the European Space Agency (ESA), and the GEOdesic Dome Array (GEODA) project from ISDEFE-INSA and the ESA. Undoubtedly, phase shifter devices are one of the key components of phased array antennas. Recent years have witnessed wide fluctuations in commercial phase shifter prices, which sometimes led to unaffordable limit. Several RF steering technique alternatives to the commercial phase shifters are proposed, summarized, and compared: the switched line phase shifter, the switched-beam network, and the novel phase shifter power splitter/combiner network. In order to show a practical use of the three different techniques, the five element GEODA-SARAS subarray is proposed as a real case of study. Finally, a practical study of a newly phase shifter power splitter/combiner network for a subarray of five radiating elements with triangular distribution is shown. Measurements of the two different phase shifter power splitter/combiner prototypes integrating the whole network are also depicted, demonstrating their proper performance. A triangular cell of three radiating elements is the simplest way to obtain a planar scanner. A new multibeam network configuration that provides three orthogonal beams in a desired _0 elevation angle and an extra one in the broadside steering direction for a triangular array of three radiating elements is introduced. Firstly, a short introduction to the state of art of classical multi-beam networks is presented. Lossless network analysis, including original lossless network designs, are also commented. General dissipative network theory as well as applications for array antennas of three radiating elements are depicted. The proposed final basic multi-beam network are simulated, built and measured to the GEODA cell practical case. A combined network that provides six orthogonal beams in a desired _0 elevation angle and a double seventh one in the broadside direction by using two complementary proposed basic networks will be shown. Measurements of the whole system will be also depicted, verifying the expected behavior. GEODA-SARAS T/R module RF chains are not a trivial design. A thorough description of all the components compounding GEODA-SARAS T/R module RF chains is presented. After presenting the general specifications of the GEODA-SARAS antenna and its block diagrams; two main blocks of the RF chains, the five element cell and the panel conversion module, are depicted and analyzed. Calibration module integrated within the two main blocks are also depicted. Signal flow throw the system analyzing critical situations such as maximum transmitted power (testing the chain unsaturation), minimum and maximum receiving signal (verifying sensitivity range), maximum receiver interference signals (assuring a proper reception), and G/T factor (fulfilling the technical specification) are evaluated. Phase quantization error effects are also listed. Finally, the manuscript contains the conclusions drawn of the present research and the future work.

Análisis y diseño de multiplicadores y mezcladores mediante el método de Monte Carlo en la banda de THz = Analysis and design of multipliers and mixers via Monte Carlo modelling at THz bands

La región del espectro electromagnético comprendida entre 100 GHz y 10 THz alberga una gran variedad de aplicaciones en campos tan dispares como la radioastronomía, espectroscopíamolecular, medicina, seguridad, radar, etc. Los principales inconvenientes en el desarrollo de estas aplicaciones son los altos costes de producción de los sistemas trabajando a estas frecuencias, su costoso mantenimiento, gran volumen y baja fiabilidad. Entre las diferentes tecnologías a frecuencias de THz, la tecnología de los diodos Schottky juega un importante papel debido a su madurez y a la sencillez de estos dispositivos. Además, los diodos Schottky pueden operar tanto a temperatura ambiente como a temperaturas criogénicas, con altas eficiencias cuando se usan como multiplicadores y con moderadas temperaturas de ruido en mezcladores. El principal objetivo de esta tesis doctoral es analizar los fenómenos físicos responsables de las características eléctricas y del ruido en los diodos Schottky, así como analizar y diseñar circuitos multiplicadores y mezcladores en bandas milimétricas y submilimétricas. La primera parte de la tesis presenta un análisis de los fenómenos físicos que limitan el comportamiento de los diodos Schottky de GaAs y GaN y de las características del espectro de ruido de estos dispositivos. Para llevar a cabo este análisis, un modelo del diodo basado en la técnica de Monte Carlo se ha considerado como referencia debido a la elevada precisión y fiabilidad de este modelo. Además, el modelo de Monte Carlo permite calcular directamente el espectro de ruido de los diodos sin necesidad de utilizar ningún modelo analítico o empírico. Se han analizado fenómenos físicos como saturación de la velocidad, inercia de los portadores, dependencia de la movilidad electrónica con la longitud de la epicapa, resonancias del plasma y efectos no locales y no estacionarios. También se ha presentado un completo análisis del espectro de ruido para diodos Schottky de GaAs y GaN operando tanto en condiciones estáticas como variables con el tiempo. Los resultados obtenidos en esta parte de la tesis contribuyen a mejorar la comprensión de la respuesta eléctrica y del ruido de los diodos Schottky en condiciones de altas frecuencias y/o altos campos eléctricos. También, estos resultados han ayudado a determinar las limitaciones de modelos numéricos y analíticos usados en el análisis de la respuesta eléctrica y del ruido electrónico en los diodos Schottky. La segunda parte de la tesis está dedicada al análisis de multiplicadores y mezcladores mediante una herramienta de simulación de circuitos basada en la técnica de balance armónico. Diferentes modelos basados en circuitos equivalentes del dispositivo, en las ecuaciones de arrastre-difusión y en la técnica de Monte Carlo se han considerado en este análisis. El modelo de Monte Carlo acoplado a la técnica de balance armónico se ha usado como referencia para evaluar las limitaciones y el rango de validez de modelos basados en circuitos equivalentes y en las ecuaciones de arrastredifusión para el diseño de circuitos multiplicadores y mezcladores. Una notable característica de esta herramienta de simulación es que permite diseñar circuitos Schottky teniendo en cuenta tanto la respuesta eléctrica como el ruido generado en los dispositivos. Los resultados de las simulaciones presentados en esta parte de la tesis, tanto paramultiplicadores comomezcladores, se han comparado con resultados experimentales publicados en la literatura. El simulador que integra el modelo de Monte Carlo con la técnica de balance armónico permite analizar y diseñar circuitos a frecuencias superiores a 1 THz. ABSTRACT The terahertz region of the electromagnetic spectrum(100 GHz-10 THz) presents a wide range of applications such as radio-astronomy, molecular spectroscopy, medicine, security and radar, among others. The main obstacles for the development of these applications are the high production cost of the systems working at these frequencies, highmaintenance, high volume and low reliability. Among the different THz technologies, Schottky technology plays an important rule due to its maturity and the inherent simplicity of these devices. Besides, Schottky diodes can operate at both room and cryogenic temperatures, with high efficiency in multipliers and moderate noise temperature in mixers. This PhD. thesis is mainly concerned with the analysis of the physical processes responsible for the characteristics of the electrical response and noise of Schottky diodes, as well as the analysis and design of frequency multipliers and mixers at millimeter and submillimeter wavelengths. The first part of the thesis deals with the analysis of the physical phenomena limiting the electrical performance of GaAs and GaN Schottky diodes and their noise performance. To carry out this analysis, a Monte Carlo model of the diode has been used as a reference due to the high accuracy and reliability of this diode model at millimeter and submillimter wavelengths. Besides, the Monte Carlo model provides a direct description of the noise spectra of the devices without the necessity of any additional analytical or empirical model. Physical phenomena like velocity saturation, carrier inertia, dependence of the electron mobility on the epilayer length, plasma resonance and nonlocal effects in time and space have been analysed. Also, a complete analysis of the current noise spectra of GaAs and GaN Schottky diodes operating under static and time varying conditions is presented in this part of the thesis. The obtained results provide a better understanding of the electrical and the noise responses of Schottky diodes under high frequency and/or high electric field conditions. Also these results have helped to determine the limitations of numerical and analytical models used in the analysis of the electrical and the noise responses of these devices. The second part of the thesis is devoted to the analysis of frequency multipliers and mixers by means of an in-house circuit simulation tool based on the harmonic balance technique. Different lumped equivalent circuits, drift-diffusion and Monte Carlo models have been considered in this analysis. The Monte Carlo model coupled to the harmonic balance technique has been used as a reference to evaluate the limitations and range of validity of lumped equivalent circuit and driftdiffusion models for the design of frequency multipliers and mixers. A remarkable feature of this reference simulation tool is that it enables the design of Schottky circuits from both electrical and noise considerations. The simulation results presented in this part of the thesis for both multipliers and mixers have been compared with measured results available in the literature. In addition, the Monte Carlo simulation tool allows the analysis and design of circuits above 1 THz.

Infiltration of a photonic crystal fiber with cholesteric liquid crystal and blue phase

Photonic crystal fibers (PCF) have been selectively filled with a cholesteric liquid crystal (ChLC) with special interest in the blue phase (BP) of the liquid crystal. It has been observed thermal tuning of the guided light in the visible region. A dramatically enhance appears when the phase of the liquid crystal changes from cholesteric to blue phase I (BPI). When a thermal range of the blue phase I is achieved, no changes are observed while increasing temperature from BPI through BPII and to the isotropic phase.