Advanced Characterisation of a Coffee Fermenting Tank by Multi-distributed Wireless Sensors: Spatial Interpolation and Phase Space Graphs

The fermentation stage is considered to be one of the critical steps in coffee processing due to its impact on the final quality of the product. The objective of this work is to characterise the temperature gradients in a fermentation tank by multi-distributed, low-cost and autonomous wireless sensors (23 semi-passive TurboTag® radio-frequency identifier (RFID) temperature loggers). Spatial interpolation in polar coordinates and an innovative methodology based on phase space diagrams are used. A real coffee fermentation process was supervised in the Cauca region (Colombia) with sensors submerged directly in the fermenting mass, leading to a 4.6 °C temperature range within the fermentation process. Spatial interpolation shows a maximum instant radial temperature gradient of 0.1 °C/cm from the centre to the perimeter of the tank and a vertical temperature gradient of 0.25 °C/cm for sensors with equal polar coordinates. The combination of spatial interpolation and phase space graphs consistently enables the identification of five local behaviours during fermentation (hot and cold spots).

Análisis de sistemas eléctricos en microsatélites. Desarrollo de módulos para una Concurrent Design Facility (CFD)para el desarrollo y análisis de misiones espaciales = Analysis of microsatellites power subsystems (battery testing). Development and programming of a new Propulsion Module for a space mission Concurrent Design Facility (CDF)

El objetivo de este proyecto es recoger y explicar el conjunto de tareas realizadas durante el proceso de colaboración llevado a cabo en el Instituto de Microgravedad “Ignacio Da Riva” durante el curso académico 2014/2015, las cuales han conformado las prácticas externas cursadas en la titulación de Grado en Ingeniería Aeroespacial, y el Trabajo de Fin de Grado de la misma titulación. En este documento se pretende,además, poner de manifiesto la rigurosidad con la que se trabaja en el ámbito espacial y la importancia de los protocolos y procedimientos para asegurar un resultado adecuado en los trabajos realizados. Una parte importante del proyecto detalla los procesos de monitorización y mantenimiento de la batería del satélite universitario UPMSat-2 cuyo lanzamiento está previsto para el año próximo y el cual será el segundo satélite del mundo en incorporar una batería de Ión-Litio.

Análisis de sistemas eléctricos en microsatélites. Desarrollo de módulos para una Concurrent Design Facility (CDF) para desarrollo y análisis de misiones espaciales = Analysis of microsatellites power subsystems (battery testing). Development and programming of a new Orbit Design Module for a space mission Concurrent Design Facility (CDF)

El presente proyecto se ha realizado durante las prácticas curriculares que han tenido lugar en el Instituto Universitario de Microgravedad “Ignacio Da Riva” (IDR/UPM). A lo largo de estas prácticas se han llevado a cabo trabajos en diversos campos, todos relacionados con el UPMSat-2, desde el subsistema de potencia (placas solares y baterías) hasta el desarrollo de módulos para la Sala de Diseño Concurrente (Concurrent Design Facility, CDF). En la realización de las mismas se ha trabajado en equipo, junto con otros dos alumnos. El objetivo del proyecto es recopilar las tareas realizadas, proporcionando el desarrollo teórico necesario para llevar a cabo todas ellas. Al ser un trabajo con varias partes claramente diferenciadas, se ha optado por comenzar con unas páginas dedicadas a las misiones espaciales. A continuación el trabajo se adentra en el subsistema de potencia de un satélite, particularizando para el UPMSat-2. Finalmente, se proporciona la teoría necesaria para el desarrollo del módulo de misión de la CDF del IDR/UPM, software que se ha desarrollado y tiene reservado un espacio al final, en el cual se describe el programa y se realizan comparaciones de los resultados que proporciona frente a casos reales.

Análisis en sistemas eléctricos en microsatélites. Desarrollo de módulos para una Concurrent Design Facility (CDF) para desarrollo y análisis de misiones espaciales = Analysis of microsatellites power subsystems (battery testing). Development and programming of a new Orbit Design Module for a space mission Concurrent Design Facility (CDF)

El objetivo de este trabajo de fin de grado es la exposición de los resultados y conclusiones, fruto de las tareas desarrolladas durante las practicas curriculares en el Instituto Universitario de Microgravedad “Ignacio Da Riva” (IDR/UPM) el presente curso académico. La estructura del trabajo se compone de dos bloques diferenciados entre sí: el seguimiento de una batería y el desarrollo de un módulo para una CDF.

High-brightness all semiconductor laser at 1.57 µm for space-borne lidar measurements of atmospheric carbon dioxide: device design and analysis of requirements

The availability of suitable laser sources is one of the main challenges in future space missions for accurate measurement of atmospheric CO2. The main objective of the European project BRITESPACE is to demonstrate the feasibility of an all-semiconductor laser source to be used as a space-borne laser transmitter in an Integrated Path Differential Absorption (IPDA) lidar system. We present here the proposed transmitter and system architectures, the initial device design and the results of the simulations performed in order to estimate the source requirements in terms of power, beam quality, and spectral properties to achieve the required measurement accuracy. The laser transmitter is based on two InGaAsP/InP monolithic Master Oscillator Power Amplifiers (MOPAs), providing the ON and OFF wavelengths close to the selected absorption line around 1.57 µm. Each MOPA consists of a frequency stabilized Distributed Feedback (DFB) master oscillator, a modulator section, and a tapered semiconductor amplifier optimized to maximize the optical output power. The design of the space-compliant laser module includes the beam forming optics and the thermoelectric coolers.The proposed system replaces the conventional pulsed source with a modulated continuous wave source using the Random Modulation-Continuous Wave (RM-CW) approach, allowing the designed semiconductor MOPA to be applicable in such applications. The system requirements for obtaining a CO2 retrieval accuracy of 1 ppmv and a spatial resolution of less than 10 meters have been defined. Envelope estimated of the returns indicate that the average power needed is of a few watts and that the main noise source is the ambient noise.

Pseudo-random single photon counting for space-borne atmospheric sensing applications

The ability to accurately observe the Earth's carbon cycles from space gives scientists an important tool to analyze climate change. Current space-borne Integrated-Path Differential Absorption (IPDA) Iidar concepts have the potential to meet this need. They are mainly based on the pulsed time-offlight principle, in which two high energy pulses of different wavelengths interrogate the atmosphere for its transmission properties and are backscattered by the ground. In this paper, feasibility study results of a Pseudo-Random Single Photon Counting (PRSPC) IPDA lidar are reported. The proposed approach replaces the high energy pulsed source (e.g. a solidstate laser), with a semiconductor laser in CW operation with a similar average power of a few Watts, benefiting from better efficiency and reliability. The auto-correlation property of Pseudo-Random Binary Sequence (PRBS) and temporal shifting of the codes can be utilized to transmit both wavelengths simultaneously, avoiding the beam misalignment problem experienced by pulsed techniques. The envelope signal to noise ratio has been analyzed, and various system parameters have been selected. By restricting the telescopes field-of-view, the dominant noise source of ambient light can be suppressed, and in addition with a low noise single photon counting detector, a retrieval precision of 1.5 ppm over 50 km along-track averaging could be attained. We also describe preliminary experimental results involving a negative feedback Indium Gallium Arsenide (InGaAs) single photon avalanche photodiode and a low power Distributed Feedback laser diode modulated with PRBS driven acoustic optical modulator. The results demonstrate that higher detector saturation count rates will be needed for use in future spacebourne missions but measurement linearity and precision should meet the stringent requirements set out by future Earthobserving missions.

High brightness semiconductor lasers as transmitters for space lidar systems

High brightness semiconductor lasers are potential transmitters for future space lidar systems. In the framework of the European Project BRITESPACE, we propose an all-semiconductor laser source for an Integrated Path Differential Absorption lidar system for column-averaged measurements of atmospheric CO2 in future satellite missions. The complete system architecture has to be adapted to the particular emission properties of these devices using a Random Modulated Continuous Wave approach. We present the initial experimental results of the InGaAsP/InP monolithic Master Oscillator Power Amplifiers, providing the ON and OFF wavelengths close to the selected absorption line around 1572 nm.

Random-modulation cw lidar system for space-borne carbon dioxide remote sensing based on a high-brightness semiconductor laser

In this paper, we report on the progresses of the BRITESPACE Consortium in order to achieve space-borne LIDAR measurements of atmospheric carbon dioxide concentration based on an all semiconductor laser source at 1.57 ?m. The complete design of the proposed RM-CW IPDA LIDAR has been presented and described in detail. Complete descriptions of the laser module and the FSU have been presented. Two bended MOPAs, emitting at the sounding frequency of the on- and off- IPDA channels, have been proposed as the transmitter optical sources with the required high brightness. Experimental results on the bended MOPAs have been presented showing a high spectral purity and promising expectations on the high output power requirements. Finally, the RM-CW approach has been modelled and an estimation of the expected SNR for the entire system is presented. Preliminary results indicate that a CO2 retrieval precision of 1.5 ppm could be achieved with an average output power of 2 W for each channel.

Urbanization patterns and their impacts on social restructuring of urban space in Chilean mid-cities: The case of Los Angeles, Central Chile

El artículo analiza las relaciones entre los cambios de uso en el territorio rural de la región del Biobío y sus efectos en el crecimiento urbano y demográfico de una ciudad de tamaño medio. En forma específica se estudia el desarrollo de la industria forestal y sus efectos sobre el proceso urbano de Los Angeles.

Crisis and the city: neoliberalism, austerity planning and the production of space

The current crisis, with its particularly severe configuration in Southern European countries, provides an opportunity to probe the interrelation of economic crunches and the production of space, and also to imagine potential paths of sociospatial emancipation from the dictates of global markets. This introductory chapter offers a preliminary interpretive framework exploring the fundamental role of urban and territorial restructuring in the formation, management and resolution of capitalist crises and, conversely, periods of crisis as key stages in the history of urbanization. I will begin by contextualizing the 2007-8 economic slump, the subsequent global recession and its uneven impact on states and cities in the longue durée of capitalist productions of space, studying the transformation of spatial configurations in previous episodes of economic stagnation. This broader perspective will then be used to analyze currently emerging formations of austerity urbanism, showing how the practices of crisis management incorporate a strategy for economic and institutional restructuring that eventually impacts on urban policy, and indeed in the production of urban space itself.

State space models for multi-setup operational modal analysis

Operational Modal Analysis consists on estimate the modal parameters of a structure (natural frequencies, damping ratios and modal vectors) from output-only vibration measurements. The modal vectors can be only estimated where a sensor is placed, so when the number of available sensors is lower than the number of tested points, it is usual to perform several tests changing the position of the sensors from one test to the following (multiple setups of sensors): some sensors stay at the same position from setup to setup, and the other sensors change the position until all the tested points are covered. The permanent sensors are then used to merge the mode shape estimated at each setup (or partial modal vectors) into global modal vectors. Traditionally, the partial modal vectors are estimated independently setup by setup, and the global modal vectors are obtained in a postprocess phase. In this work we present two state space models that can be used to process all the recorded setups at the same time, and we also present how these models can be estimated using the maximum likelihood method. The result is that the global mode shape of each mode is obtained automatically, and subsequently, a single value for the natural frequency and damping ratio of the mode is computed. Finally, both models are compared using real measured data.

Propellantless deorbiting of space debris by bare electrodynamic tethers : final report

A Space tether is a thin, multi-kilometers long conductive wire, joining a satellite and some opposite end mass, and keeping vertical in orbit by the gravity-gradient. The ambient plasma, being highly conductive, is equipotential in its own co-moving frame. In the tether frame, in relative motion however, there is in the plasma a motional electric field of order of 100 V/km, product of (near) orbital velocity and geomagnetic field. The electromotive force established over the tether length allows plasma contactor devices to collect electrons at one polarized-positive (anodic) end and eject electrons at the opposite end, setting up a current along a standard, fully insulated tether. The Lorentz force exerted on the current by the geomagnetic field itself is always drag; this relies on just thermodynamics, like air drag. The bare tether concept, introduced in 1992 at the Universidad Politécnica de Madrid (UPM), takes away the insulation and has electrons collected over the tether segment coming out polarized positive; the concept rests on 2D (Langmuir probe) current-collection in plasmas being greatly more efficient than 3D collection. A Plasma Contactor ejects electrons at the cathodic end. A bare tether with a thin-tape cross section has much greater perimeter and de-orbits much faster than a (corresponding) round bare tether of equal length and mass. Further, tethers being long and thin, they are prone to cuts by abundant small space debris, but BETs has shown that the tape has a probability of being cut per unit time smaller by more than one order of magnitude than the corresponding round tether (debris comparable to its width are much less abundant than debris comparable to the radius of the corresponding round tether). Also, the tape collects much more current, and de-orbits much faster, than a corresponding multi-line “tape” made of thin round wires cross-connected to survive debris cuts. Tethers use a dissipative mechanism quite different from air drag and can de-orbit in just a few months; also, tape tethers are much lighter than round tethers of equal length and perimeter, which can capture equal current. The 3 disparate tape dimensions allow easily scalable design. Switching the cathodic Contactor off-on allows maneuvering to avoid catastrophic collisions with big tracked debris. Lorentz braking is as reliable as air drag. Tethers are still reasonably effective at high inclinations, where the motional field is small, because the geomagnetic field is not just a dipole along the Earth polar axis. BETs is the EC FP7/Space Project 262972, financed in about 1.8 million euros, from 1 November 2010 to 31 January 2014, and carrying out RTD work on de-orbiting space debris. Coordinated by UPM, it has partners Università di Padova, ONERA-Toulouse, Colorado State University, SME Emxys, DLR–Bremen, and Fundación Tecnalia. BETs work involves 1) Designing, building, and ground-testing basic hardware subsystems Cathodic Plasma Contactor, Tether Deployment Mechanism, Power Control Module, and Tape with crosswise and lengthwise structure. 2) Testing current collection and verifying tether dynamical stability. 3) Preliminary design of tape dimensions for a generic mission, conducive to low system-to-satellite mass ratio and probability of cut by small debris, and ohmic-effects regime of tether current for fast de-orbiting. Reaching TRL 4-5, BETs appears ready for in-orbit demostration.

El espacio intermedio = The intermediate space

Las cualidades de los espacios intermedios se relacionan históricamente con conceptos que tradicionalmente les han dado nombre: solana, mirador, galería, balcón, logia, umbráculo, porche, terraza, veranda y patio. En la actualidad, las propiedades de estos nuevos espacios suelen responder a situaciones complejas y diversas, mas difíciles de ajustar a un solo término.

De la cápsula comunitaria al espacio compartido. La búsqueda del post-espacio público en la vivienda de ACM = From community capsules to shared intervals. The search of the post-public space In the housing developments by ACM

Arquitectos y no arquitectos como Rossi, Grassi, Jacobs, Sennett o Lefebvre, denunciaron críticamente durante los 50, 50 y 70 la ruptura entre la calle y el espacio doméstico y el consiguiente declive del dominio público urbano a escala de ciudad y a escala de barrio. La crítica a la "Ville Contemporaine" no solo se escribía, también se dibujaba y a veces, incluso, se construía. La primera generación post-CIAM trabajó intensamente en desmentir con palabras y obras al Oud que ya en los años 20 del pasado siglo, tomando la delantera a Le Corbusier y desde su mejor sentido práctico y estético afirmaba: "Las calles para el negocio, los patios interiores para la vida. Los dos estrictamente separados y con un carácter contradictorio".