New steps in the development of the second generation TEC GESMEY

The paper shows the results of the new steps that have been done in the development of the tidal energy converter GESMEY. These are the design, construction and trials into the sea of a 1/10 scale prototype and also the construction with the same scale of the buoy BOSCEM, that anchors the device and lets it in the correct work position and depth, along the two directions of the flow that the daily tidal cycle have. Inside the paper is described the objectives and the methodology of the experimental trials that were ca rry out the last summer with the scale prototype. GESMEY is a new type of tidal energy converter (TEC) that has the capability to exploit currents in waters over forty meters by itself and it gets only using its internal ballast system the necessary equilibrium between hy drostatics and hydrodynamics forces to make the emersion and the immersion procedures without any other help. Finally the paper shows the description of the results obtained over the performance of the devices along the immersion, emersion and floating transport manoeuvres and afterwards the results, that were obtained along the generation power tests that were carried out, are shown.

Risk-based methodology for parameter calibration of a reservoir flood control model

Flash floods are of major relevance in natural disaster management in the Mediterranean region. In many cases, the damaging effects of flash floods can be mitigated by adequate management of flood control reservoirs. This requires the development of suitable models for optimal operation of reservoirs. A probabilistic methodology for calibrating the parameters of a reservoir flood control model (RFCM) that takes into account the stochastic variability of flood events is presented. This study addresses the crucial problem of operating reservoirs during flood events, considering downstream river damages and dam failure risk as conflicting operation criteria. These two criteria are aggregated into a single objective of total expected damages from both the maximum released flows and stored volumes (overall risk index). For each selected parameter set the RFCM is run under a wide range of hydrologic loads (determined through Monte Carlo simulation). The optimal parameter set is obtained through the overall risk index (balanced solution) and then compared with other solutions of the Pareto front. The proposed methodology is implemented at three different reservoirs in the southeast of Spain. The results obtained show that the balanced solution offers a good compromise between the two main objectives of reservoir flood control management

Smart aeronautical structures: development and experimental validation of a structural health monitoring system for damage detection

En muchas áreas de la ingeniería, la integridad y confiabilidad de las estructuras son aspectos de extrema importancia. Estos son controlados mediante el adecuado conocimiento de danos existentes. Típicamente, alcanzar el nivel de conocimiento necesario que permita caracterizar la integridad estructural implica el uso de técnicas de ensayos no destructivos. Estas técnicas son a menudo costosas y consumen mucho tiempo. En la actualidad, muchas industrias buscan incrementar la confiabilidad de las estructuras que emplean. Mediante el uso de técnicas de última tecnología es posible monitorizar las estructuras y en algunos casos, es factible detectar daños incipientes que pueden desencadenar en fallos catastróficos. Desafortunadamente, a medida que la complejidad de las estructuras, los componentes y sistemas incrementa, el riesgo de la aparición de daños y fallas también incrementa. Al mismo tiempo, la detección de dichas fallas y defectos se torna más compleja. En años recientes, la industria aeroespacial ha realizado grandes esfuerzos para integrar los sensores dentro de las estructuras, además de desarrollar algoritmos que permitan determinar la integridad estructural en tiempo real. Esta filosofía ha sido llamada “Structural Health Monitoring” (o “Monitorización de Salud Estructural” en español) y este tipo de estructuras han recibido el nombre de “Smart Structures” (o “Estructuras Inteligentes” en español). Este nuevo tipo de estructuras integran materiales, sensores, actuadores y algoritmos para detectar, cuantificar y localizar daños dentro de ellas mismas. Una novedosa metodología para detección de daños en estructuras se propone en este trabajo. La metodología está basada en mediciones de deformación y consiste en desarrollar técnicas de reconocimiento de patrones en el campo de deformaciones. Estas últimas, basadas en PCA (Análisis de Componentes Principales) y otras técnicas de reducción dimensional. Se propone el uso de Redes de difracción de Bragg y medidas distribuidas como sensores de deformación. La metodología se validó mediante pruebas a escala de laboratorio y pruebas a escala real con estructuras complejas. Los efectos de las condiciones de carga variables fueron estudiados y diversos experimentos fueron realizados para condiciones de carga estáticas y dinámicas, demostrando que la metodología es robusta ante condiciones de carga desconocidas. ABSTRACT In many engineering fields, the integrity and reliability of the structures are extremely important aspects. They are controlled by the adequate knowledge of existing damages. Typically, achieving the level of knowledge necessary to characterize the structural integrity involves the usage of nondestructive testing techniques. These are often expensive and time consuming. Nowadays, many industries look to increase the reliability of the structures used. By using leading edge techniques it is possible to monitoring these structures and in some cases, detect incipient damage that could trigger catastrophic failures. Unfortunately, as the complexity of the structures, components and systems increases, the risk of damages and failures also increases. At the same time, the detection of such failures and defects becomes more difficult. In recent years, the aerospace industry has done great efforts to integrate the sensors within the structures and, to develop algorithms for determining the structural integrity in real time. The ‘philosophy’ has being called “Structural Health Monitoring” and these structures have been called “smart structures”. These new types of structures integrate materials, sensors, actuators and algorithms to detect, quantify and locate damage within itself. A novel methodology for damage detection in structures is proposed. The methodology is based on strain measurements and consists in the development of strain field pattern recognition techniques. The aforementioned are based on PCA (Principal Component Analysis) and other dimensional reduction techniques. The use of fiber Bragg gratings and distributed sensing as strain sensors is proposed. The methodology have been validated by using laboratory scale tests and real scale tests with complex structures. The effects of the variable load conditions were studied and several experiments were performed for static and dynamic load conditions, demonstrating that the methodology is robust under unknown load conditions.

Estudio preliminar acerca del uso de protocolos y actos comunicativos FIPA en el sistema COMPUTAPLEX

Este trabajo corresponde con la implementación de componentes software dentro de la Plataforma COMPUTAPLEX, la cual tiene como objetivo facilitar a los investigadores la realización de tareas del proceso experimental de ingeniería de software. Uno de los aportes a esta plataforma tecnológica corresponde con el desarrolló de los componentes necesarios para la recuperación de datos experimentales disponibles en diversas fuentes de datos, para ello se hizo uso de un mecanismo capaz de unificar la extracción de información de MySQL, ficheros excel y ficheros SPSS. Con ello diferentes grupos de investigación asociados pueden compartir y tener acceso a repositorios experimentales que se mantienen tanto de manera local como externa. Por otra parte, se ha realizado un estudio de la tecnología de agentes en la que se describe sus definiciones, lenguajes de comunicación, especificación FIPA, JADE como implementación FIPA y parser XML. Además para este trabajo se ha definido e implementado una ontología de comunicación entre agentes, la misma que fue diseñada en la herramienta Protégé. En lo que se refiere al desarrollo de componentes se hizo uso de una amplía variedad de tecnologías que incluye lenguaje de programación Java, framework JADE para el desarrollo de agentes, librería JENA para manejo de ontologías, librería SAXParser para lectura de archivos XML y patrón de diseño Factory. Finalmente se describe la metodología de trabajo utilizada en el proyecto, la cual por medio de la realización de varios ciclos iterativos permitió obtener prototipos que poco a poco fueron cubriendo las necesidades del producto software.----ABSTRACT---- This work relates to the implementation of software components within the platform Computaplex, which aims to enable researchers to conduct experimental software engineering process tasks. One of the contributions to this platform technology corresponds to the development of components which are necessary for the recovery of experimental data available in different data sources, to archive this goal a mechanism able to unify the extraction of information from MySQL, Excel and SPSS files was made. Therefore, associated research groups can share and access experimental repositories that remain both locally and externally. Moreover, it has been conducted a study of agent technology in its definition is described, languages communication, FIPA, JADE and FIPA implementation and XML parser. In addition to this work, it has been defined and implemented an ontology for communication between agents, the same as was designed in the Protégé tool. In what refers to the development of components, a wide range of technologies have been made which includes Java programming language, framework JADE for agent development, JENA library for handling ontologies, SAXParser for reading XML files and Factory design pattern. Finally, describing the work methodology used in this project, which through the implementation of several iterative cycles allowed to obtain prototypes were gradually meeting the needs of the software product.

The Role of Knowledge Modeling Techniques in Software Development: A General Approach Based on a Knowledge Management Tool

The aim of the paper is to discuss the use of knowledge models to formulate general applications. First, the paper presents the recent evolution of the software field where increasing attention is paid to conceptual modeling. Then, the current state of knowledge modeling techniques is described where increased reliability is available through the modern knowledge acquisition techniques and supporting tools. The KSM (Knowledge Structure Manager) tool is described next. First, the concept of knowledge area is introduced as a building block where methods to perform a collection of tasks are included together with the bodies of knowledge providing the basic methods to perform the basic tasks. Then, the CONCEL language to define vocabularies of domains and the LINK language for methods formulation are introduced. Finally, the object oriented implementation of a knowledge area is described and a general methodology for application design and maintenance supported by KSM is proposed. To illustrate the concepts and methods, an example of system for intelligent traffic management in a road network is described. This example is followed by a proposal of generalization for reuse of the resulting architecture. Finally, some concluding comments are proposed about the feasibility of using the knowledge modeling tools and methods for general application design.

Design, development and construction of an outdoor testing facility for semi-transparent photovoltaic modules

Building-integrated Photovoltaics (BIPV) is one of the most promising technologies enabling buildings to generate on-site part of their electricity needs while performing architectural functionalities. A clear example of BIPV products consists of semi-transparent photovoltaic modules (STPV), designed to replace the conventional glazing solutions in building façades. Accordingly, the active building envelope is required to perform multiple requirements such as provide solar shading to avoid overheating, supply solar gains and thermal insulation to reduce heat loads and improve daylight utilization. To date, various studies into STPV systems have focused on their energy performance based on existing simulation programs, or on the modelling, normally validated by limited experimental data, of the STPV modules thermal behaviour. Taking into account that very limited experimental research has been conducted on the energy performance of STPV elements and that the characterization in real operation conditions is necessary to promote an energetically efficient integration of this technology in the building envelope, an outdoor testing facility has been designed, developed and built at the Solar Energy Institute of the Technical University of Madrid. In this work, the methodology used in the definition of the testing facility, its capability and limitations are presented and discussed.

Supporting the design and development of Project Based Learning courses.

The use of Project Based Learning has spread widely over the last decades, not only throughout countries but also among disciplines. One of the most significant characteristics of this methodology is the use of ill-structured problems as central activity during the course, which represents an important difficulty for both teachers and students. This work presents a model, supported by a tool, focused on helping teachers and students in Project Based Learning, overcoming these difficulties. Firstly, teachers are guided in designing the project following the main principles of this methodology. Once the project has been specified at the desired level of depth, the same tool helps students to finish the project specification and organize the implementation. Collaborative work among different users is allowed in both phases. This tool has been satisfactorily tested designing two real projects used in Computer Engineering and Software Engineering degrees.

Reduced carbon and energy footprint in highway operations: the Highway Energy Assessment (HERA) methodology

Global demand for mobility is increasing and the environmental impact of transport has become an important issue in transportation network planning and decision-making, as well as in the operational management phase. Suitable methods are required to assess emissions and fuel consumption reduction strategies that seek to improve energy efficiency and furthering decarbonization. This study describes the development and application of an improved modeling framework – the HERA (Highway EneRgy Assessment) methodology – that enables to assess the energy and carbon footprint of different highways and traffic flow scenarios and their comparison. HERA incorporates an average speed consumption model adjusted with a correction factor which takes into account the road gradient. It provides a more comprehensive method for estimating the footprint of particular highway segments under specific traffic conditions. It includes the application of the methodology to the Spanish highway network to validate it. Finally, a case study shows the benefits from using this methodology and how to integrate the objective of carbon footprint reductions into highway design, operation and scenario comparison.

Climatic analysis methodology of vernacular architecture

Vernacular architecture has demonstrated its perfect environmental adaptation through its empirical development and improvement by generations of user-builders. Nowadays, the sustainability of vernacular architecture is the aim of some research projects in which the same method should be applied in order to be comparable. Hence, we propose a research method putting together various steps. Through the analysis of geographical, lithology, economic, cultural and social influence as well as materials and constructive systems, vernacular architecture is analyzed. But, all this information is put together with the natural landscape (topography and vegetation) and the climatic data (temperature, winds, rain and sun exposure). In addition, the use of bioclimatic charts, such as Olgyay or Givoni’s, revealed the necessities and strategies in urban and building design. They are satisfied in the vernacular architecture by the application of different energy conservation mechanisms, some of them are shown by different examples in this paper.

Methodology for developing and application outsourcing in the cloud using SOA

New technologies such as, the new Information and Communication Technology ICT, break new paths and redefines the way we understand business, the Cloud Computing is one of them. The on demand resource gathering and the per usage payment scheme are now commonplace, and allows companies to save on their ICT investments. Despite the importance of this issue, we still lack methodologies that help companies, to develop applications oriented for its exploitation in the Cloud. In this study we aim to fill this gap and propose a methodology for the development of ICT applications, which are directed towards a business model, and further outsourcing in the Cloud. In the former the Development of SOA applications, we take, as a baseline scenario, a business model from which to obtain a business process model. To this end, we use software engineering tools; and in the latter The Outsourcing we propose a guide that would facilitate uploading business models into the Cloud; to this end we describe a SOA governance model, which controls the SOA. Additionally we propose a Cloud government that integrates Service Level Agreements SLAs, plus SOA governance, and Cloud architecture. Finally we apply our methodology in an example illustrating our proposal. We believe that our proposal can be used as a guide/pattern for the development of business applications.

A methodology to compute emission projections from road transport (EmiTRANS)

Atmospheric emissions from road transport have increased all around the world during the last decades more rapidly than from other pollution sources. For instance, they contribute to more than 25% of total CO, CO2, NOx, and fine particle emissions in most of the European countries. This situation shows the importance of road transport when complying with emission ceilings and air quality standards applied to these pollutants. This paper presents a modelling system to perform atmospheric emission projections (simultaneously both air quality pollutants and greenhouse gases) from road transport including the development of a tailored software tool (EmiTRANS) as a planning tool. The methodology has been developed with two purposes: 1) to obtain outputs used as inputs to the COPERT4 software to calculate emission projections and 2) to summarize outputs for policy making evaluating the effect of emission abatement measures for a vehicle fleet. This methodology has been applied to the calculation of emission projections in Spain up to 2020 under several scenarios, including a sensitivity analysis useful for a better interpretation and confidence building on the results. This case study demonstrates the EmiTRANS applicability to a country, and points out the need for combining both technical and non-technical measures (such as behavioural changes or demand management) to reduce emissions, indirectly improving air quality and contributing to mitigate climate change.

Methodology proposal for the life cycle sustainability assessment applied to retrofitting in a local context

In the European context of upgrading the housing stock energy performance, multiple barriers hinder the wide uptake of sustainable retrofitting practices. Moreover, some of these may imply negative effects often disregarded. Policy makers need to identify how to increase and improve retrofitting practices from the comprehensive point of view of sustainability. None of the existing assessment tools addresses all the issues relevant for sustainable development in a local situation from a life cycle perspective. Life cycle sustainability assessment methodology, or LCSA, analyzes environmental and socioeconomic impacts. The environmental part is quite developed, but the socioeconomic aspect is still challenging. This work proposes socioeconomic criteria to be included in a LCSA to assess retrofitting works in the specific context of Brussels-Capital Region. LCSA feasibility and challenging methodology aspects are discussed.

Methodology based on FBG sensors for monitoring of FRP-strengthened beams

Advanced composite materials are increasingly used in the strengthening of reinforced concrete (RC) structures. The use of externally bonded strips made of fibre-reinforced plastics (FRP) as strengthening method has gained widespread acceptance in recent years since it has many advantages over the traditional techniques. However, unfortunately, this strengthening method is often associated with a brittle and sudden failure caused by some form of FRP bond failure, originated at the termination of the FRP material or at intermediate areas in the vicinity of flexural cracks in the RC beam. Up to date, little effort in the early prediction of the debonding in its initial instants even though this effect is not noticeable by simple visual observation. An early detection of this phenomenon might help in taking actions to prevent future catastrophes. Fibre-optic Bragg grating (FBG) sensors are able to measure strains locally with high resolution and accuracy. Furthermore, as their physical size is extremely small compared with other strain measuring components, it enables to be embedded at the concrete-FRP interface for determining the strain distribution without influencing the mechanical properties of the host materials. This paper shows the development of a debonding identification methodology based on strains experimentally measured. For, it a simplified model is implemented to simulate the behaviour of FRP-strengthened reinforced concrete beams. This model is taken as a basis to. develop an model updating procedure able to detect minor debonding at the concrete-FRP interface from experimental strains obtained by using FBG sensors embedded at the interface

Building an ontology catalogue for smart cities

Apart from providing semantics and reasoning power to data, ontologies enable and facilitate interoperability across heterogeneous systems or environments. A good practice when developing ontologies is to reuse as much knowledge as possible in order to increase interoperability by reducing heterogeneity across models and to reduce development effort. Ontology registries, indexes and catalogues facilitate the task of finding, exploring and reusing ontologies by collecting them from different sources. This paper presents an ontology catalogue for the smart cities and related domains. This catalogue is based on curated metadata and incorporates ontology evaluation features. Such catalogue represents the first approach within this community and it would be highly useful for new ontology developments or for describing and annotating existing ontologies.

Analysis of Contributions to NO2 Ambient Air Quality Levels in Madrid City (Spain) through Modeling. Implications for the Development of Policies and Air Quality Monitoring

As environmental standards become more stringent (e.g. European Directive 2008/50/EC), more reliable and sophisticated modeling tools are needed to simulate measures and plans that may effectively tackle air quality exceedances, common in large cities across Europe, particularly for NO2. Modeling air quality in urban areas is rather complex since observed concentration values are a consequence of the interaction of multiple sources and processes that involve a wide range of spatial and temporal scales. Besides a consistent and robust multi-scale modeling system, comprehensive and flexible emission inventories are needed. This paper discusses the application of the WRF-SMOKE-CMAQ system to the Madrid city (Spain) to assess the contribution of the main emitting sectors in the region. A detailed emission inventory was compiled for this purpose. This inventory relies on bottom-up methods for the most important sources. It is coupled with the regional traffic model and it makes use of an extensive database of industrial, commercial and residential combustion plants. Less relevant sources are downscaled from national or regional inventories. This paper reports the methodology and main results of the source apportionment study performed to understand the origin of pollution (main sectors and geographical areas) and define clear targets for the abatement strategy. Finally the structure of the air quality monitoring is analyzed and discussed to identify options to improve the monitoring strategy not only in the Madrid city but the whole metropolitan area.