Despliegues de femtoceldas LTE en interiores comparación con otras tecnologías inalámbricas

Long Term Evolution (LTE) has appeared with the aim of improving the performance of 3G networks, increasing spectral efficiency and peak rates both at downlink and uplink, reducing latency and increasing flexibility of frequency allocation. Therefore, LTE is expected to have a key role in the development of wireless networks and services in the next years, and, of course, in specific dedicated in-building solutions. Due to that fact, an analysis of LTE performance in indoor scenarios in terms of capacity and grade of service is essential, as well as its comparison with other indoor solutions, pointing out the technical challenges derived, and describing and proposing performance assessment rules to be used in LTE deployments.

A novel scanning lens instrument for evaluating Fresnel lens performance: equipment development and initial results

A system dedicated to the optical transmittance characterization of Fresnel lenses has been developed at NREL, in collaboration with the UPM. The system quantifies the optical efficiency of the lens by generating a performance map. The shape of the focused spot may also be analyzed to understand change in the lens performance. The primary instrument components (lasers and CCD detector) have been characterized to confirm their capability for performing optical transmittance measurements. Measurements performed on SoG and PMMA lenses subject to a variety of indoor conditions (e.g., UV and damp heat) identified differences in the optical efficiency of the evaluated lenses, demonstrating the ability of the Scanning Lens Instrument (SLI) to distinguish between the aged lenses.

Urban agriculture in the new framework of green cities.

Urban Agriculture was a common practice in the old times. However after a period of low interest by urban population there is a movement of renaissance of urban agriculture especially in the new megalopolis. It is important to understand the role of UA in the new framework, and the interface of urban and rural agricultures, with their comparative advantages. Thus, we describe the impact of UA in several scenarios: political, socioeconomic and environmental. As a consequence several actions should be developed for improving the situation, with the stimulus to UA: urban planning, food value chain, appropriate technology, education and extension services, entertainment and leisure, selection of botanic varieties and agrochemical inputs, design and landscape and good farming practices. As a complement, there is an analysis of the Urban Greening Value Organization in our society. In the paper there is a description of the situation of urban agriculture in Spain (located mainly in roofs, walls, indoor and ground places) the existence of local regulations, barriers and opportunities in the new situation. Due to the social dimension of urban agriculture there are some comments about the role of the more significant stakeholders, and the goals and the structure of the neighbor communities.

A 3D multi-objective optimization planning algorithm for wireless sensor networks

The complexity of planning a wireless sensor network is dependent on the aspects of optimization and on the application requirements. Even though Murphy's Law is applied everywhere in reality, a good planning algorithm will assist the designers to be aware of the short plates of their design and to improve them before the problems being exposed at the real deployment. A 3D multi-objective planning algorithm is proposed in this paper to provide solutions on the locations of nodes and their properties. It employs a developed ray-tracing scheme for sensing signal and radio propagation modelling. Therefore it is sensitive to the obstacles and makes the models of sensing coverage and link quality more practical compared with other heuristics that use ideal unit-disk models. The proposed algorithm aims at reaching an overall optimization on hardware cost, coverage, link quality and lifetime. Thus each of those metrics are modelled and normalized to compose a desirability function. Evolutionary algorithm is designed to efficiently tackle this NP-hard multi-objective optimization problem. The proposed algorithm is applicable for both indoor and outdoor 3D scenarios. Different parameters that affect the performance are analyzed through extensive experiments; two state-of-the-art algorithms are rebuilt and tested with the same configuration as that of the proposed algorithm. The results indicate that the proposed algorithm converges efficiently within 600 iterations and performs better than the compared heuristics.

Bankable procedures for the technical quality assurance of large scale PV plants

Strict technical quality assurance procedures are essential for PV plant bankability. When large-scale PV plants are concerned, this is typically accomplished in three consecutive phases: an energy yield forecast, that is performed at the beginning of the project and is typically accomplished by means of a simulation exercise performed with dedicated software; a reception test campaign, that is performed at the end of the commissioning and consists of a set of tests for determining the efficiency and the reliability of the PV plant devices; and a performance analysis of the first years of operation, that consists in comparing the real energy production with the one calculated from the recorded operating conditions and taking into account the maintenance records. In the last six years, IES-UPM has offered both indoor and on-site quality control campaigns for more than 60 PV plants, with an accumulated power of more than 300 MW, in close contact with Engineering, Procurement and Construction Contractors and financial entities. This paper presents the lessons learned from such experience.

A VLC-based beacon location system for mobile applications

This paper proposes a low cost and complexity indoor location and navigation system using visible light communications and a mobile device. LED lamps work as beacons transmitting an identifier code so a mobile device can know its location. Experimental designs for transmitter and receiver interfaces are presented and potential applications are discussed.

Proceso de replanteo de un nodo urbano

El continuo desarrollo que está teniendo el mundo de las telecomunicaciones móviles hace que la red móvil esté sufriendo progresivos cambios para adaptarse a las nuevas tecnologías móviles que ofrecen un mejor servicio. El cambio en la red móvil no solo se produce por el desarrollo de las nuevas generaciones móviles. La red móvil se adapta también a la demanda de usuarios la cual no deja de incrementar a lo largo de los últimos años. Por tanto, los operadores tienen que ampliar su red instalando nodos que tengan las nuevas tecnologías y también las anteriores. Aparte de crear nuevos nodos también tienen que modificar sus nodos antiguos y convertirlos en nodos que soporten mayor número de usuarios. Hoy en día, en España, se están instalando nuevos nodos con 2G, 3G y 4G y además se están realizando ampliaciones de portadora para 3G. Este proyecto se divide en cuatro partes, la primera de ella se centra en explicar el proceso a seguir para la instalación de un nuevo nodo urbano. Este proceso es muy parecido para instalar un nodo con una tecnología u otra, en el caso del proyecto se explicarán los pasos a seguir para la instalación de un nodo con 2G y 3G. Posteriormente se explicará cómo se realizan las medidas para corroborar el correcto funcionamiento de un nodo rural y se compararán a las medidas de zona urbana mediante capturas de un nodo específico. En la penúltima parte del proyecto se estudia la cobertura en interiores y las diversas soluciones que se toman normalmente para mejorar dicha cobertura en edificios, almacenes y centros comerciales. Por último aparecen las conclusiones del proyecto y los trabajos futuros en donde se realiza una visión de posibles estudios relacionados con este proyecto y una visión de cómo puede quedar formada la red en unos años. ABSTRACT. Due to the continuous development of mobile telecommunications the mobile networks have undergone rapid changes to adapt to new mobile technologies that offer a better service. The mobile network change hasn´t only occurred because of the development of new generations of mobile radio-communications. The mobile network adapts itself to user demand, which has been growing over the last few years faster than expected. Therefore, mobile operators have to enlarge its network by installing nodes that share the old and new technologies. Apart from creating new nodes, the operators have to modify the old ones and turn them into nodes that support an increasing number of users. Nowadays, in Spain new nodes with 2G 3G and 4G are being installed, and carrier extensions for 3G are being made as well. This project is divided into four parts. The first chapter focuses on explaining the process that should be followed to install a new urban node. This process is similar to install a node with any of the technologies available. In the case of this project, the steps to follow in setting up a wireless node with 2G and 3G will be detailed. Afterwards, in the second chapter the document continues explaining the measurements that should be carried out to ensure proper performance of a rural node. Then, those measurements will be compared with the ones of an urban node. In the third part of the project it is explained how coverage indoor studies are performed, and the different solutions that are usually proposed to improve coverage in buildings, stores and shopping centers. The last chapter explains the conclusions that have been reached and future works. It is provided a widespread view of possible studies related to this project and how the mobile will improve in the following years.

Integración arquitectónica y constructiva de sistemas fotovoltaicos de tecnología de lámina delgada en relación con la disipación térmica y almacenamiento de calor

Esta tesis doctoral contribuye al análisis y desarrollo de nuevos elementos constructivos que integran sistemas de generación eléctrica a través de células fotovoltaicas (FV); particularmente, basados en tecnología FV de lámina delgada. Para ello se estudia el proceso de la integración arquitectónica de éstos elementos (conocido internacionalmente como “Building Integrated Photovoltaic – BIPV”) mediante diferentes metodologías. Se inicia con el estudio de los elementos fotovoltaicos existentes y continúa con los materiales que conforman actualmente las pieles de los edificios y su posible adaptación a las diferentes tecnologías. Posteriormente, se propone una estrategia de integración de los elementos FV en los materiales constructivos. En ésta se considera la doble función de los elementos BIPV, eléctrica y arquitectónica, y en especial se plantea el estudio de la integración de elementos de disipación térmica y almacenamiento de calor mediante los materiales de cambio de fase (“Phase Change Materials – PCM”), todo esto con el objeto de favorecer el acondicionamiento térmico pasivo a través del elemento BIPV. Para validar dicha estrategia, se desarrolla una metodología experimental que consiste en el diseño y desarrollo de un prototipo denominado elemento BIPV/TF – PCM, así como un método de medida y caracterización en condiciones de laboratorio. Entre los logros alcanzados, destaca la multifuncionalidad de los elementos BIPV, el aprovechamiento de la energía residual del elemento, la reducción de los excedentes térmicos que puedan modificar el balance térmico de la envolvente del edificio, y las mejoras conseguidas en la producción eléctrica de los módulos fotovoltaicos por reducción de temperatura, lo que hará más sostenible la solución BIPV. Finalmente, como resultado del análisis teórico y experimental, esta tesis contribuye significativamente al estudio práctico de la adaptabilidad de los elementos BIPV en el entorno urbano por medio de una metodología que se basa en el desarrollo y puesta en marcha de una herramienta informática, que sirve tanto a ingenieros como arquitectos para verificar la calidad de la integración arquitectónica y calidad eléctrica de los elementos FV, antes, durante y después de la ejecución de un proyecto constructivo. ABSTRACT This Doctoral Thesis contributes to the analysis and development of new building elements that integrate power generation systems using photovoltaic solar cells (PV), particularly based on thin-film PV technology. For this propose, the architectural integration process is studied (concept known as "Building Integrated Photovoltaic - BIPV") by means of different methodologies. It begins with the study of existing PV elements and materials that are currently part of the building skins and the possible adaptation to different technologies. Subsequently, an integration strategy of PV elements in building materials is proposed. Double function of BIPV elements is considered, electrical and architectural, especially the heat dissipation and heat storage elements are studied, particularly the use Phase Change Materials– PCM in order to favor the thermal conditioning of buildings by means of the BIPV elements. For this propose, an experimental methodology is implemented, which consist of the design and develop of a prototype "BIPV/TF- PCM element" and measurement method (indoor laboratory conditions) in order to validate this strategy. Among the most important achievements obtained of this develop and results analysis includes, in particular, the multifunctionality of BIPV elements, the efficient use of the residual energy of the element, reduction of the excess heat that it can change the heat balance of the building envelope and improvements in electricity production of PV modules by reducing the temperature, are some benefits achieved that make the BIPV element will be more sustainable. Finally, as a result of theoretical and experimental analysis, this thesis contributes significantly to the practical study of the adaptability of BIPV elements in the urban environment by means of a novel methodology based on the development and implementation by computer software of a useful tool which serves as both engineers and architects to verify the quality of architectural integration and electrical performance of PV elements before, during, and after execution of a building projects.

Análisis biomecánico zancada a zancada de la prueba "60 metros vallas" durante los campeonatos del mundo y de España de pista cubierta Valencia 2008

El principal objetivo del presente trabajo de investigación fue determinar las diferencias en distintas variables relacionadas con el rendimiento físico entre atletas de distinto nivel durante la prueba de los 60 metros vallas. Un total de 59 vallistas masculinos (los 31 participantes en el Campeonato del Mundo Absoluto de Pista Cubierta y los 28 participantes en el Campeonato de España Absoluto de Pista Cubierta, ambos celebrados en Valencia en el año 2008) formaron la muestra del estudio. El análisis biomecánico se realizó mediante un sistema fotogramétrico en dos dimensiones que permitió calcular, aplicando algoritmos basados en el procedimiento de la DLT (Abdel-Aziz y Karara, 1971), las coordenadas (x, y) de los sucesivos apoyos de los pies de los atletas sobre toda la superficie de competición. La filmación de las pruebas se llevó a cabo con seis cámaras de vídeo, ubicadas sobre la gradas, con una frecuencia de muestreo para el tratamiento de los datos de 50 Hz. En la fase de salida, los atletas de nivel superior mostraron una menor longitud (p<0,05) y tiempo de zancada (p<0,001), debido a un menor tiempo de vuelo (p<0,05). En la fase de vallas, los atletas de nivel más elevado presentaron mayores distancia de ataque a la valla (p<0,001), así como menores distancias de caída de la valla (p<0,001), tiempos de zancada (p<0,01-0,001) y de apoyo (p<0,01-0,001 ) en los cuatro pasos que conforman cada ciclo de vallas, así como un menor tiempo de vuelo en el paso de valla (p<0,001) y en el paso de transición (p<0,001). De manera adicional, se encontraron importantes diferencias en el reparto de los pasos entre vallas entre la primera y tercera valla y el resto de obstáculos. En la fase final, se observó una mayor longitud de zancada en los atletas de nivel superior (p<0,001), así como un menor tiempo de zancada (p<0,01) y de apoyo (p<0,01). Los resultados obtenidos en el presente estudio de investigación avalan la utilización de la fotogrametría en dos dimensiones para el análisis biomecánico de la prueba de 60 metros vallas en competición. Su aplicación en competiciones del máximo nivel internacional ha posibilitado conocer las características de los vallistas a lo largo de toda la prueba y determinar posibles implicaciones de cara al proceso de entrenamiento. ABSTRACT The aim of this research was to determine the differences in different variables related to physical performance among athletes of different levels during the race of 60 meter hurdles. A total of 59 male hurdlers (the 31 participants in the World Indoor Championship and the 28 participants in the Spanish Indoor Championship, both held in Valencia in 2008) formed the sample of the study. The biomechanical analysis of athletes was performed using a two-dimensional photogrammetric system which enabled calculation, applying algorithms based on the DLT method (Abdel -Aziz y Karara , 1971), the coordinates (x , y) of the successive supports of the feet on the entire competition surface. Filming test was conducted with six video cameras, located on the bleachers, with a sampling frequency for data processing of 50 Hz. In the approach run phase, the top-level athletes showed a smaller length step (p<0.05), and shorter step time (p<0.001), due to a shorter step flight time (p<0.05). In the hurdle unit phase, the higher level athletes had greater take-off distances (p<0.001), shorter landing distances (p<0.001), smaller step times (p<0.01-0.001), and support times (p<0.01- 0.001) in the four steps that comprised each hurdle unit, and smaller flight times in the hurdle step (p < 0.001), and the recovery step (p<0.001). Additionally, differences in the distribution of hurdle unit steps between the first and third hurdle, and other hurdles were found. In the run-in phase, a greater step length in top-level athletes (p<0.001), and a shorter step time (p<0.01) and contact time (p<0.01) was observed. The results obtained in this study support the use of photogrammetry in two dimensions for biomechanical analysis in 60 meter hurdles competition events. Its application at the highest international level competitions has allowed to know the characteristics of the hurdlers over the entire race and identify possible implications for the training process.

Experimental analysis of energy savings and hygrothermal conditions improvement by means of air curtaines in stores with intensive pedestrian traffic

Current worldwide building legislation requirements aim to the design and construction of technical services that reduce energy consumption and improve indoor hygrothermal conditions. The retail sector in Spain, with a lot of outdated technical systems, demands energy conservation measures in order to reduce the increasingly electrical consumption for cooling. Climatic separation with modern air curtains and advanced hygrothermal control systems enables energy savings and can keep suitable indoor air temperature and humidity of stores with intense pedestrian traffic, especially when located in hot humid climates. As stated in the article, the energy savings in commercial buildings with these systems exceeds 30%

Towards a fuel poverty definition for Spain

During the last years, an increasing interest has been developed so as to address the problem of fuel poverty which is already affecting a huge number of European citizens. In 2013, the European Parliament has claimed to the Commission and State Members through several resolutions, the legislative development of policies in order to tackle energy vulnerability of households. In 2000 the UK Government, through the Warm Homes and Energy Conservation Act, established that a person could be regarded as fuel poor if he is a member of a household that cannot get warmth at a reasonable cost. Nevertheless, in order to establish the incidence of fuel poverty among Spanish households, it must be understood which should be the adequate thresholds for indoor temperatures. The research here presented proposes new indoor temperature thresholds for fuel poor households based on adaptive comfort models.

Fuel poverty as a determinant in energy retrofitting actions

Fuel poverty can be defined as “the inability to afford adequate warmth in the home" and it is the result of the combination of three items: low household income, housing lack of energy efficiency and high energy bills. Although it affects a growing number of households within the European Union only some countries have an official definition for it. In 2013, the European Parliament claimed the Commission and Estate Members to develop different policies in order to fight household energy vulnerability. The importance of tackling fuel poverty is based on the critical consequences it has for human health living below certain temperatures. In Spain some advances have been made in this field but main existing studies remain at the statistical level and do not deepen the understanding of the problem from the perspective of dwelling indoor habitability conditions. What is more, this concept is yet to be officially defined. This paper presents the evaluation of fuel poverty in a building block of social housing located in the centre of Zaragoza and how this issue determined the strategies implemented in the energy retrofitting intervention project. At a first step, fuel poverty was appraised through the exploration of indoor thermal conditions. The adaptive thermal comfort (UNE-EN 15251:2008) method was used to establish the appropriate indoor temperatures and consequently to determine what can be called 'comfort gap'. Results were collated and verified with energy bills collection and a survey work that gathered data from neighbours. All this permitted pointing out those households more in need. Results from the social analysis combined with the evaluation of the building thermal performance determined the intervention. The renovation project was aimed at the implementation of passive strategies that improve households thermal comfort in order to alleviate households fuel poverty situation. This research is part of the project NewSolutions4OldHousing (LIFE10 ENV/ES/439) cofounded by the European Commission under the LIFE+ Programme.

Técnicas avanzadas de diseño y análisis de rendimiento en despliegues inalámbricos en interiores

En los últimos tiempos, el tráfico generado por los usuarios de redes móviles ha crecido de manera muy notable, y se prevé que dicho crecimiento se mantenga de manera continuada a lo largo de los próximos años. El tráfico gestionado por redes móviles se ha multiplicado por cinco entre los años 2010 y 2013, y las predicciones señalan un aumento de diez veces entre 2013 y 2019. De este tráfico que deben gestionar las redes móviles, una gran parte se genera en el interior de edificios. En la actualidad, éste oscila entre el 70% y el 80% del tráfico móvil total, y este porcentaje se prevé que aumente hasta cerca del 95% en los próximos años. En esta situación, con el tráfico móvil aumentando de manera exponencial, especialmente en interiores, el despliegue de soluciones específicas para estos entornos se antoja imprescindible para evitar situaciones de saturación constante de las redes móviles. Desde el punto de vista de los operadores móviles, estas soluciones permitirán limitar los problemas de cobertura, mejorar la eficiencia del uso de recursos radio y reducir el coste de las infraestructuras. Asimismo, desde el punto de vista de los usuarios, estos despliegues específicos en interiores permitirán suministrar de manera continua altas tasas de transferencia y satisfacer los altos requisitos de calidad de servicio que demandan los servicios en tiempo real. La complejidad de las actuaciones a realizar para llevar a cabo el despliegue de soluciones específicas en interiores varía considerablemente según el tipo de entorno al que están destinadas. Por un lado, las soluciones en escenarios de tipo residencial se caracterizan por despliegues masivos de transmisores realizados por los propios usuarios. De esta manera, no hay posibilidad de realizar ningún tipo de planificación previa que permita la optimización del rendimiento y solo se puede recurrir, para la mejora de éste, a métodos de autoconfiguración y autooptimización. Por otro lado, las soluciones en entornos empresariales se caracterizan por la necesidad de realizar una labor de diseño y planificación previa, cuya dificultad estará asociada a las dimensiones del escenario de despliegue y al número de transmisores necesarias. De esta labor de diseño y de la configuración de los elementos involucrados en la solución desplegada dependerá el funcionamiento adecuado de la red, el rendimiento conseguido y la calidad del servicio que se podrá suministrar a través de ésta. En esta Tesis Doctoral se abordan dos de los problemas principales en el ámbito del despliegue de soluciones específicas de interiores. El primero de ellos es la dificultad para estimar la capacidad y el rendimiento que puede garantizarse mediante soluciones autodesplegadas, y el segundo es la complejidad de diseñar y configurar despliegues de soluciones específicas de interiores en entornos empresariales que requieran un número de transmisores considerable. En el ámbito de los autodespliegues en escenarios residenciales, las principales contribuciones originales de esta Tesis Doctoral se centran en el diseño, desarrollo e implementación de procedimientos que permitan de manera sencilla y precisa la estimación de la capacidad y el rendimiento en autodespliegues. Por otro lado, en el ámbito de los despliegues en escenarios empresariales, las aportaciones originales de esta Tesis consisten en el desarrollo de nuevas técnicas que permitan el diseño automático de soluciones específicas de interiores en estos entornos. Los resultados obtenidos han permitido la creación de herramientas específicas para el análisis del rendimiento de autodespliegues en escenarios residenciales reales y para el diseño y configuración de despliegues en escenarios empresariales. Estas herramientas permiten sistematizar la aplicación práctica de las contribuciones de la presente Tesis Doctoral. ABSTRACT In recent times, the traffic generated by users of mobile networks has grown very significantly, and this increase is expected to continue steadily over the next few years. Traffic carried by mobile networks has increased fivefold between 2010 and 2013, and forecasts indicate a tenfold increase between 2013 and 2019. Furthermore, a great part of this traffic is generated inside buildings. Currently, between 70% and 80% of mobile traffic occurs inside buildings, and this percentage is expected to increase to about 95% in the coming years. In this situation, with mobile traffic growing exponentially, especially indoors, the deployment of specific solutions for these environments can be essential to avoid a constant saturation of mobile networks. On the one hand, from the point of view of mobile operators, these solutions will help to reduce the problems of coverage, improve the efficiency of radio resource usage and reduce the cost of infrastructures. Also, from the point of view of users, these specific indoor deployments can both guarantee high data transfer rates and meet the high quality of service requirements associated with real-time services. The complexity of the actions required to carry out the deployment of specific solutions indoors varies considerably depending on the type of scenario they are conceived to. On the one hand, residential scenarios are characterized by massive deployments of base stations made by the user, so there is no possibility of any prior planning. In this case only self-configuration, selfoptimization and self-healing methods can be considered for performance optimization. On the other hand, specific in-building solutions in enterprise environments requires a previous design and planning phase, whose difficulty is closely associated with the size of the deployment scenario and the number of base stations required. The design and configuration of the elements included in the solution will determine its performance and the quality of service that can be guaranteed. The objective of the present Thesis is to address two of the main issues related to specific indoor solutions, such as the difficulty of assessing the capacity and the performance which can be guaranteed by means of self-deployments and the complexity of the design and configuration of deployments in enterprise environments requiring a large number of base stations. The main contribution of this thesis consists of the development of techniques and simple tools for design and performance analysis of indoor wireless networks deployments. The main results include the development of procedures for assessing the capacity and performance of self-deployments in residential scenarios, the performance analysis of real residential self-deployments using the proposed procedures and the development of techniques for the automatic design of wireless networks in enterprise environments. The results obtained have allowed the creation of specific software tools for both the performance analysis of self-deployments and the design and deployment of in-building solutions in enterprise scenarios. These software tools are conceived to systematize the practical application of the contributions of this Thesis.

Entornos termodinámicos. Una cartografía crítica en torno a la energía y la arquitectura

En los últimos años, y a la luz de los retos a los que se enfrenta la sociedad, algunas voces están urgiendo a dejar atrás los paradigmas modernos —eficiencia y rendimiento— que sustentan a las llamadas prácticas sostenibles, y están alentando a repensar, en el contexto de los cambios científicos y culturales, una agenda termodinámica y ecológica para la arquitectura. La cartografía que presenta esta tesis doctoral se debe de entender en este contexto. Alineándose con esta necesidad, se esfuerza por dar a este empeño la profundidad histórica de la que carece. De este modo, el esfuerzo por dotar a la arquitectura de una agenda de base científica, se refuerza con una discusión cultural sobre el progresivo empoderamiento de las ideas termodinámicas en la arquitectura. Esta cartografía explora la historia de las ideas termodinámicas en la arquitectura desde el principio del siglo XX hasta la actualidad. Estudia, con el paso de los sistemas en equilibrio a los alejados del equilibrio como trasfondo, como las ideas termodinámicas han ido infiltrándose gradualmente en la arquitectura. Este esfuerzo se ha planteado desde un doble objetivo. Primero, adquirir una distancia crítica respecto de las prácticas modernas, de modo que se refuerce y recalibre el armazón intelectual y las herramientas sobre las que se está apoyando esta proyecto termodinámico. Y segundo, desarrollar una aproximación proyectual sobre la que se pueda fundamentar una agenda termodinámica para la arquitectura, asunto que se aborda desde la firme creencia de que es posible una re-descripción crítica de la realidad. De acuerdo con intercambios de energía que se dan alrededor y a través de un edificio, esta cartografía se ha estructurado en tres entornos termodinámicos, que sintetizan mediante un corte transversal la variedad de intercambios de energía que se dan en la arquitectura: -Cualquier edificio, como constructo espacial y material inmerso en el medio, intercambia energía mediante un flujo bidireccional con su contexto, definiendo un primer entorno termodinámico al que se denomina atmósferas territoriales. -En el interior de los edificios, los flujos termodinámicos entre la arquitectura y su ambiente interior definen un segundo entorno termodinámico, atmósferas materiales, que explora las interacciones entre los sistemas materiales y la atmósfera interior. -El tercer entorno termodinámico, atmosferas fisiológicas, explora los intercambios de energía que se dan entre el cuerpo humano y el ambiente invisible que lo envuelve, desplazando el objeto de la arquitectura desde el marco físico hacia la interacción entre la atmósfera y los procesos somáticos y percepciones neurobiológicas de los usuarios. A través de estos tres entornos termodinámicos, esta cartografía mapea aquellos patrones climáticos que son relevantes para la arquitectura, definiendo tres situaciones espaciales y temporales sobre las que los arquitectos deben actuar. Estudiando las conexiones entre la atmósfera, la energía y la arquitectura, este mapa presenta un conjunto de ideas termodinámicas disponibles —desde los parámetros de confort definidos por la industria del aire acondicionado hasta las técnicas de acondicionamiento pasivo— que, para ser efectivas, necesitan ser evaluadas, sintetizadas y recombinadas a la luz de los retos de nuestro tiempo. El resultado es un manual que, mediando entre la arquitectura y la ciencia, y a través de este relato histórico, acorta la distancia entre la arquitectura y la termodinámica, preparando el terreno para la definición de una agenda termodinámica para el proyecto de arquitectura. A este respecto, este mapa se entiende como uno de los pasos necesarios para que la arquitectura recupere la capacidad de intervenir en la acuciante realidad a la que se enfrenta. ABSTRACT During the last five years, in the light of current challenges, several voices are urging to leave behind the modern energy paradigms —efficiency and performance— on which the so called sustainable practices are relying, and are posing the need to rethink, in the light of the scientific and cultural shifts, the thermodynamic and ecological models for architecture. The historical cartography this PhD dissertation presents aligns with this effort, providing the cultural background that this endeavor requires. The drive to ground architecture on a scientific basis needs to be complemented with a cultural discussion of the history of thermodynamic ideas in architecture. This cartography explores the history of thermodynamic ideas in architecture, from the turn of the 20th century until present day, focusing on the energy interactions between architecture and atmosphere. It surveys the evolution of thermodynamic ideas —the passage from equilibrium to far from equilibrium thermodynamics— and how these have gradually empowered within design and building practices. In doing so, it has posed a double-objective: first, to acquire a critical distance with modern practices which strengthens and recalibrates the intellectual framework and the tools in which contemporary architectural endeavors are unfolding; and second, to develop a projective approach for the development a thermodynamic agenda for architecture and atmosphere, with the firm belief that a critical re-imagination of reality is possible. According to the different systems which exchange energy across a building, the cartography has been structured in three particular thermodynamic environments, providing a synthetic cross-section of the range of thermodynamic exchanges which take place in architecture: -Buildings, as spatial and material constructs immersed in the environment, are subject to a contiuous bidirectional flow of energy with its context, defining a the first thermodynamic environment called territorial atmospheres. -Inside buildings, the thermodynamic flow between architecture and its indoor ambient defines a second thermodynamic environment, material atmospheres, which explores the energy interactions between the indoor atmosphere and its material systems. -The third thermodynamic environment, physiological atmospheres, explores the energy exchanges between the human body and the invisible environment which envelopes it, shifting design drivers from building to the interaction between the atmosphere and the somatic processes and neurobiological perceptions of users. Through these three thermodynamic environments, this cartography maps those climatic patterns which pertain to architecture, providing three situations on which designers need to take stock. Studying the connections between atmosphere, energy and architecture this map presents, not a historical paradigm shift from mechanical climate control to bioclimatic passive techniques, but a range of available thermodynamic ideas which need to be assessed, synthesized and recombined in the light of the emerging challenges of our time. The result is a manual which, mediating between architecture and science, and through this particular historical account, bridges the gap between architecture and thermodynamics, paving the way to a renewed approach to atmosphere, energy and architecture. In this regard this cartography is understood as one of the necessary steps to recuperate architecture’s lost capacity to intervene in the pressing reality of contemporary societies.

Influencia del tratamiento "a fuego" en las características del estuco tradicional con cal = Influence of treatment "by fire" in the characteristics of traditional lime stucco

Esta investigación avanza en el intento de recuperar la técnica tradicional del estuco a fuego, paradigma de la decoración de espacios interiores hasta la mitad del s. XX por sus imitaciones marmóreas de gran calidad. Para ejecutarlos se utilizaban morteros de cal con áridos de mármol, pigmentos minerales y grasas; con estos materiales se preparaban y tendían las masas, se pintaban al fresco y se terminaban con el paso de una herramienta metálica caliente. Como sucede con otras técnicas, el paso del tiempo ha difuminado los conocimientos sobre la materia, haciendo muy difícil la conservación o restauración de los ejemplos en nuestro patrimonio. A partir de la escasa bibliografía existente se ha recuperado el proceso, sometiendo las muestras elaboradas a diferentes ensayos que han caracterizado el acabado final,tanto en sus características intrínsecas como en las que le son conferidas al proteger finalmente las muestras con una capa de cera, tal y como se realizaba tradicionalmente.---ABSTRACT---This research advances in the attempt to recover the traditional technique of stucco by fire; paradigm of indoor decoration until half of 20th century due to its high quality marbled imitations. On its implementation process, it was used lime mortars with marble aggregates, mineral pigments and greases. With these materials, masses were prepared and extended into the walls, they were painted in fresco and ended with the passage of a heated metal tool. As with any other technique, the time passing over has blurred the knowledge on the subject, making very difficult the preservation or restoration of examples in our heritage. Despite of the limited literature, the process has been recovered; subjecting the samples prepared at different trials that have characterized the finished, both in its merits and its conferred characteristics by finally protecting the samples with a layer of wax, as was done traditionally.