Development of low cost photovoltaic sensor for over-tree radiation assessment

The crop diseases sometimes are related to the irradiance that the crop receives. When an experiment requires the measurement of the irradiance, usually it results in an expensive data acquisition system. If it is necessary to check many test points, the use of traditional sensors will increase the cost of the experiment. By using low cost sensors based in the photovoltaic effect, it is possible to perform a precise test of irradiance with a reduced price. This work presents an experiment performed in Ademuz (Valencia, Spain) during September of 2011 to check the validity of low cost sensors based on solar cells.

Tanque de almacenamiento de GNL para la ampliación de la planta de regasificación de Barcelona

ENAGAS tiene la intención de ampliar el Terminal de Regasificación de GNL que tiene en el puerto de Barcelona. El presente Proyecto Básico define las instalaciones de uno de los Tanques de almacenamiento de GNL que se van a construir dentro del Alcance de dicha ampliación, con el suficiente detalle como para permitir a ENAGAS acometer las tareas previas a la ejecución del proyecto, a saber: 1. Planificar y presupuestar la fase de ejecución 2. Solicitar los Permisos y Autorizaciones necesarias de los Organismos competentes 3. Lanzar la Petición de Ofertas para el concurso llave en mano del EPC. Los trabajos de Ingeniería contenidos en el Proyecto Básico son los siguientes: Antecedentes y Datos básicos, Criterios de diseño, Descripción de instalaciones, Cálculos estructurales, Planos del Tanque de GNL, Definición de equipos y materiales a utilizar, Plan de ejecución del proyecto, Especificaciones técnicas para Ingeniería, Compras y Construcción, Paquete para Petición de Ofertas del EPC, Condiciones técnicas particulares, Programa de ejecución y Presupuesto de inversiones. ABSTRACT ENAGAS is expanding its LNG Regasification Terminal located in Barcelona Port (Spain). This Document reports the Front End Engineering and Design (FEED) works undertaken in relation to one of the LNG Storage Tanks to be built within the scope of that expansion. The Project FEED hereby presented comprehensively defines the LNG Storage Tank so as to allow ENAGAS to perform next stages of the Works, namely: 1. Plan and budget the Project Execution phase 2. Request Regulatory authorizations 3. Invite Contractors to bid for the LNG Tank EPC. Main components of the FEED Document contents are as follow:Background and Basic Data, Design Criteria, Description of LNG Tank elements, Engineering Calculations, LNG Tank Drawings, Equipment and Materials definition, Project Execution Plan (PEP), Technical Conditions, EPC Invitation to Tender (ITT) package, Execution Schedule and Cost Estimate.

Methodological Proposal for Teamwork Evaluation in the field of training Project Management.

Teamwork, is one of the abilities that today is highly valued in the professional arena with a great importance for various personal and interpersonal skills associated with it. In this context, the Technical University of Madrid, is developing a coordinated educational innovation project, which main objective is to develop methodological and assessment tools for the acquisition of personal skills necessary to improve the employability of graduates and their skills for project management. Within this context, this paper proposes a methodology composed of various activities and indicators, as well as specific assessment instruments linked to the teamwork competence. Through a series of systematic steps it was allowed the design of an instrument and construction of a scale for measuring the competence of teamwork. The practical application of the methodology has been carried out in Projects lectures from different Schools of Engineering at the Technical University of Madrid, which results are presented in this document as a pilot experience. Results show the various aspects and methods that teachers should consider in evaluating the competence of the work, including analysis of the quality of results, through reliability and construct validity. On the other hand, show the advantages of applying this methodology in the field of project management teaching.

The Experience of Helicopters subject-course in the OCW-UPM Project. A Proposal on Technology Dissemination.

An experience developed by the authors in the design of educational tools, funded on multimedia support for using in teaching, will be presented. These tools have been used on the subject of Helicopters, http://ocw.upm.es/ingenieriaaeroespacial/ helicopteros at the Universidad Politécnica de Madrid (E.U.I.T. Aeronáutica). Throughout more than ten years, these didactical and educational elements have been defined and developed. It has the singularity that most of them have been designed for undergraduate students, as a part of their end of degree projectwork. This peculiarity has led to a wide range of proposals and solutions, as well as an appropriate approach. depending on the level of knowledge. The evolution of tools for developing these materials will be presented, discussing advantages and disadvantages. Finally, we will advance the new materials which are being prepared at present.

Engineering metal precipitate size distributions to enhance gettering in multicrystalline silicon

The extraction of metal impurities during phosphorus diffusion gettering (PDG) is one of the crucial process steps when fabricating high-efficiency solar cells using low-cost, lower-purity silicon wafers. In this work, we show that for a given metal concentration, the size and density of metal silicide precipitates strongly influences the gettering efficacy. Different precipitate size distributions can be already found in silicon wafers grown by different techniques. In our experiment, however, the as-grown distribution of precipitated metals in multicrystalline Si sister wafers is engineered through different annealing treatments in order to control for the concentration and distribution of other defects. A high density of small precipitates is formed during a homogenization step, and a lower density of larger precipitates is formed during extended annealing at 740º C. After PDG, homogenized samples show a decreased interstitial iron concentration compared to as-grown and ripened samples, in agreement with simulations.

Multiobjective optimization applied to structural sizing of low cost university-class microsatellite projects

In recent years, there has been continuing interest in the participation of university research groups in space technology studies by means of their own microsatellites. The involvement in such projects has some inherent challenges, such as limited budget and facilities. Also, due to the fact that the main objective of these projects is for educational purposes, usually there are uncertainties regarding their in orbit mission and scientific payloads at the early phases of the project. On the other hand, there are predetermined limitations for their mass and volume budgets owing to the fact that most of them are launched as an auxiliary payload in which the launch cost is reduced considerably. The satellite structure subsystem is the one which is most affected by the launcher constraints. This can affect different aspects, including dimensions, strength and frequency requirements. In this paper, the main focus is on developing a structural design sizing tool containing not only the primary structures properties as variables but also the system level variables such as payload mass budget and satellite total mass and dimensions. This approach enables the design team to obtain better insight into the design in an extended design envelope. The structural design sizing tool is based on analytical structural design formulas and appropriate assumptions including both static and dynamic models of the satellite. Finally, a Genetic Algorithm (GA) multiobjective optimization is applied to the design space. The result is a Pareto-optimal based on two objectives, minimum satellite total mass and maximum payload mass budget, which gives a useful insight to the design team at the early phases of the design.

A hands-on education project: antenna design for inter-CubeSat communications

CubeSat platforms have become a de facto standard for universities willing to initiate space-technology activities with students. These small satellite platforms ease the implementation of hands-on education projects and opening the apertures of new research areas. Moreover, due to the limited volume (a 10 cm cube) and power (1 W), the application of imaginative solutions is mandatory. This leads to new innovation processes in the course of CubeSat projects. In this paper, we present a hands-on education project the aim of which is the specification, design, building and measurement of an antenna for communication between nanosatellites and, in particular, CubeSats. The project lies within the framework of ETSIT-UPM innovative education activities in the area of space technology, where students play a leading role in real engineering projects.

Infrastructure Finance in Developing Countries by State and Multilateral Development Banks

Infrastructure concession is an alternative widely used by governments to increase investment. In the case of the road sector, the main characteristics of the concessions are: long-term projects, high investments in the early years of the contract and high risks. A viability analysis must be carried out for each concession and consider the characteristics of the project. When the infrastructure is located in a developing country, political and market growth uncertainties should be add in the concession project analysis, as well as economic instability, because they present greater risks. This paper is an analysis of state bank participation in road infrastructure finance in developing countries. For this purpose, we studied road infrastructure financing and its associated risks, and also the features of developing countries. Furthermore, we considered the issue of state banks and multilateral development banks that perform an important role by offering better credit lines than the private banks, in terms of cost, interest and grace period. Based on this study, we analyzed the Brazilian Development Bank - BNDES – and their credit supply to road infrastructure concessions. The results show that BNDES is the main financing agent for long-term investment in the sector, offering loans with low interest rates in Brazilian currency. From this research we argue that a single state bank should not alone support the increasing demand for finance in Brazil. Therefore, we conclude that there is a need to expand the supply of credit in Brazil, by strengthening private banks in the long-term lending market.

Measuring the influence of Cooperative Learning and Project Based Learning on problem solvin skill.

The aim of this study is to evaluate the effects obtained after applying two active learning methodologies (cooperative learning and project based learning) to the achievement of the competence problem solving. This study was carried out at the Technical University of Madrid, where these methodologies were applied to two Operating Systems courses. The first hypothesis tested was whether the implementation of active learning methodologies favours the achievement of ?problem solving?. The second hypothesis was focused on testing if students with higher rates in problem solving competence obtain better results in their academic performance. The results indicated that active learning methodologies do not produce any significant change in the generic competence ?problem solving? during the period analysed. Concerning this, we consider that students should work with these methodologies for a longer period, besides having a specific training. Nevertheless, a close correlation between problem solving self appraisal and academic performance has been detected.

News in engineering education in Spain effective from 2010 in presence of external changes and mixed crisis, looking mostly to agro and civil engineers.

The engineering careers models were diverse in Europe, and are adopting now in Spain the Bolonia process for European Universities. Separated from older Universities, that are in part technically active, Civil Engineering (Caminos, Canales y Puertos) started at end of 18th century in Spain adopting the French models of Upper Schools for state civil servants with exam at entry. After 1800 intense wars, to conserve forest regions Ingenieros de Montes appeared as Upper School, and in 1855 also the Ingenieros Agrónomos to push up related techniques and practices. Other Engineers appeared as Upper Schools but more towards private factories. These ES got all adapted Lower Schools of Ingeniero Tecnico. Recently both grew much in number and evolved, linked also to recognized Professions. Spanish society, into European Community, evolved across year 2000, in part highly well, but with severe discordances, that caused severe youth unemployment with 2008-2011 crisis. With Bolonia process high formal changes step in from 2010-11, accepted with intense adaptation. The Lower Schools are changing towards the Upper Schools, and both that have shifted since 2010-11 various 4-years careers (Grado), some included into the precedent Professions, and diverse Masters. Acceptation of them to get students has started relatively well, and will evolve, and acceptation of new grades for employment in Spain, Europe or outside will be essential. Each Grado has now quite rigid curricula and programs, MOODLE was introduced to connect pupils, some specific uses of Personal Computers are taught in each subject. Escuela de Agronomos centre, reorganized with its old name in its precedent buildings at entrance of Campus Moncloa, offers Grados of Agronomic Engineering and Science for various public and private activities for agriculture, Alimentary Engineering for alimentary activities and control, Agro-Environmental Engineering more related to environment activities, and in part Biotechnology also in laboratories in Campus Monte-Gancedo for Biotechnology of Plants and Computational Biotechnology. Curricula include Basics, Engineering, Practices, Visits, English, ?project of end of career?, Stays. Some masters will conduce to specific professional diploma, list includes now Agro-Engineering, Agro-Forestal Biotechnology, Agro and Natural Resources Economy, Complex Physical Systems, Gardening and Landscaping, Rural Genie, Phytogenetic Resources, Plant Genetic Resources, Environmental Technology for Sustainable Agriculture, Technology for Human Development and Cooperation.

The Threads of Biosystems Engineering

The core concepts, or threads, of Biosystems Engineering (BSEN) are variously understood by those within the discipline, but have never been unequivocally defined due to its early stage of development. This makes communication and teaching difficult compared to other well established engineering subjects. Biosystems Engineering is a field of Engineering which int egrates engineering science and design with applied biological, environmental and agricultural sciences. It represents an evolution of the Agricultural Engineering discipline applied to all living organisms not including biomedical applications. The basic key element for the emerging EU Biosystems Engineering program of studies is to ensure that it offers essential minimum fundamental engine ering knowledge and competences . A core curriculum developed by Erasmus Thematic Networks is used as benchmark for Agr icultural and Biosystems Engineering studies in Europe. The common basis of the core curriculum for the discipline across the Atlantic , including a minimum of competences comprising the Biosystems Engineering core competencies, has been defined by an Atlan tis project , but this needs to be taken further by defining the threads linking courses together. This paper presents a structured approach to define the Threads of BSEN . The definition of the mid-level competences and the associated learning outcomes has been one of the objectives of the Atlantis programme TABE.NET. The mid-level competences and learning outcomes for each of six specializations of BSEN are defined while the domain-specific knowledge to be acquired for each outcome is proposed. Once the proposed definitions are adopted, these threads will be available for global development of the BSEN.

Low-cost retrofitting solutions for RC frames using masonry infill panels

A large number of reinforced concrete (RC) frame structures built in earthquake-prone areas such as Haiti are vulnerable to strong ground motions. Structures in developing countries need low-cost seismic retrofit solutions to reduce their vulnerability. This paper investigates the feasibility of using masonry infill walls to reduce deformations and damage caused by strong ground motions in brittle and weak RC frames designed only for gravity loads. A numerical experiment was conducted in which several idealized prototypes representing RC frame structures of school buildings damaged during the Port-au-Prince earthquake (Haiti, 2010) were strengthened by adding elements representing masonry infill walls arranged in different configurations. Each configuration was characterized by the ratio Rm of the area of walls in the direction of the ground motion (in plan) installed in each story to the total floor area. The numerical representations of these idealized RC frame structures with different values of Rm were (hypothetically) subjected to three major earthquakes with peak ground accelerations of approximately 0.5g. The results of the non-linear dynamic response analyses were summarized in tentative relationships between Rm and four parameters commonly used to characterize the seismic response of structures: interstory drift, Park and Ang indexes of damage, and total amount of energy dissipated by the main frame. It was found that Rm=4% is a reasonable minimum design value for seismic retrofitting purposes in cases in which available resources are not sufficient to afford conventional retrofit measures.

The NACIR Project: New Applications for CPV'S: A fast way to improve reliability and Technology progress

The main goal of this proposal is to join together the owners of the most advanced CPV technology, with respect to the state of the art, in order to research from its leading position new applications for CPV systems. In addition to opening up new markets, it will unveil possible sources of failure in new environments outside Europe, in order to assure component reliability. The proposed project will also try to improve the current technology of the industrial partners (ISOFOTON and CONCENTRIX) by accelerating the learning curve that CPV must follow in order to reach the competitive market, and lowering the cost under the current flat panel PV significantly within 3-4 years. The use of CPV systems in remote areas, together with harsher radiation, ambient and infrastructure conditions will help to increase the rate of progress of this technology. In addition, the ISFOC s contribution, which brings together seven power plants from seven CPV technologies up to 3 MWpeak, will allow creating the most complete database of components and systems performance to be generated as well as the effects of radiation and meteorology on systems operations. Finally, regarding the new applications for CPV subject, the project will use a CPV system sized 25 kWp in a stand-alone station in Egypt (NWRC) for the first time for water pumping and irrigation purposes. In a similar way ISOFOTON will connect up to 25 kWp CPV to the Moroccan ONE utility grid. From the research content point of view of this project, which is directly addressed by the scope of the call, the cooperative research between UPM, FhG-ISE and the two companies will be favoured by the fact that all are progressing in similar directions: developing two-stage optics CPV systems. In addition to these technology improvements the UPM is very interested in developing a new concept of module, recently patented, which will fulfil all required characteristics of a good CPV with less components and reducing cost.

Campus of Excellence: The Power of Diversity in Engineering Education

This paper presents the results of a strategy to modernise the Spanish University system through the establishment of an International Campus of Excellence (CEI). The current, ambitious but realistic, project is a joint initiative of a number of institutions located in the Moncloa Campus, amongst them the Complutense and the Technical Universities, as well as CIEMAT, CSIC and INIA. The aim of the project is to transform the Moncloa Campus into an international point of reference with regard to research, education and innovation. This paper describes the project and presents the qualitative and quantitative results.