Spectral-analysis-surface-waves-method in ground characterization

The prediction of train induced vibration levels in structures close to railway tracks before track construction starts is important in order to avoid having to implement costly mitigation measures afterwards. The used models require an accurate characterization of the propagation medium i.e. the soil layers. To this end the spectral analysis of surface waves (SASW) method has been chosen among the active surface waves techniques available. As dynamic source a modal sledge hammer has been used. The generated vibrations have been measured at known offsets by means of several accelerometers. There are many parameters involved in estimating the experimental dispersion curve and, later on, thickness and propagation velocities of the different layers. Tests have been carried out at the Segovia railway station. Its main building covers some of the railway tracks and vibration problems in the building should be avoided. In the paper these tests as well as the influence of several parameters on the estimated soil profile will be detailed.

A bankable method for the field testingor a CPV plant

The bankability of CPV projects is an important issue to pave the way toward a swift and sustained growth in this technology. The bankability of a PV plant is generally addressed through the modeling of its energy yield under a b aseline loss scenario, followed by an on-site measurement campaign aimed at verifying its energetic behavior. The main difference between PV and CPV resides in the proper CPV modules, in particular in the inclusion of optical lements and III-V multijunction cells that are much more sensitive to spectral variations than xSi cells, while the rest of the system behaves in a way that possesses many common points with xSi technology. The modeling of the DC power output of a CPV system thus requires several impo rtant second order parameters to be considered, mainly related to optics, spectral direct solar radiation, wind speed, tracker accuracy and heat dissipation of cells.

Homography-based ground plane detection using a single on-board camera

This study presents a robust method for ground plane detection in vision-based systems with a non-stationary camera. The proposed method is based on the reliable estimation of the homography between ground planes in successive images. This homography is computed using a feature matching approach, which in contrast to classical approaches to on-board motion estimation does not require explicit ego-motion calculation. As opposed to it, a novel homography calculation method based on a linear estimation framework is presented. This framework provides predictions of the ground plane transformation matrix that are dynamically updated with new measurements. The method is specially suited for challenging environments, in particular traffic scenarios, in which the information is scarce and the homography computed from the images is usually inaccurate or erroneous. The proposed estimation framework is able to remove erroneous measurements and to correct those that are inaccurate, hence producing a reliable homography estimate at each instant. It is based on the evaluation of the difference between the predicted and the observed transformations, measured according to the spectral norm of the associated matrix of differences. Moreover, an example is provided on how to use the information extracted from ground plane estimation to achieve object detection and tracking. The method has been successfully demonstrated for the detection of moving vehicles in traffic environments.

A Variational Stereo Method for the Three-Dimensional Reconstruction of Ocean Waves

We develop a novel remote sensing technique for the observation of waves on the ocean surface. Our method infers the 3-D waveform and radiance of oceanic sea states via a variational stereo imagery formulation. In this setting, the shape and radiance of the wave surface are given by minimizers of a composite energy functional that combines a photometric matching term along with regularization terms involving the smoothness of the unknowns. The desired ocean surface shape and radiance are the solution of a system of coupled partial differential equations derived from the optimality conditions of the energy functional. The proposed method is naturally extended to study the spatiotemporal dynamics of ocean waves and applied to three sets of stereo video data. Statistical and spectral analysis are carried out. Our results provide evidence that the observed omnidirectional wavenumber spectrum S(k) decays as k-2.5 is in agreement with Zakharov's theory (1999). Furthermore, the 3-D spectrum of the reconstructed wave surface is exploited to estimate wave dispersion and currents.

Order 10 4 speedup in global linear instability analysis using matrix formation

A unified solution framework is presented for one-, two- or three-dimensional complex non-symmetric eigenvalue problems, respectively governing linear modal instability of incompressible fluid flows in rectangular domains having two, one or no homogeneous spatial directions. The solution algorithm is based on subspace iteration in which the spatial discretization matrix is formed, stored and inverted serially. Results delivered by spectral collocation based on the Chebyshev-Gauss-Lobatto (CGL) points and a suite of high-order finite-difference methods comprising the previously employed for this type of work Dispersion-Relation-Preserving (DRP) and Padé finite-difference schemes, as well as the Summationby- parts (SBP) and the new high-order finite-difference scheme of order q (FD-q) have been compared from the point of view of accuracy and efficiency in standard validation cases of temporal local and BiGlobal linear instability. The FD-q method has been found to significantly outperform all other finite difference schemes in solving classic linear local, BiGlobal, and TriGlobal eigenvalue problems, as regards both memory and CPU time requirements. Results shown in the present study disprove the paradigm that spectral methods are superior to finite difference methods in terms of computational cost, at equal accuracy, FD-q spatial discretization delivering a speedup of ð (10 4). Consequently, accurate solutions of the three-dimensional (TriGlobal) eigenvalue problems may be solved on typical desktop computers with modest computational effort.

Theoretical Stark broadening parameters for spectral lines arising from the 2p5ns, 2p5np and 2p5nd electronic configurations of MgIII

In the present work we report theoretical Stark widths and shifts calculated using the Griem semi-empirical approach, corresponding to 237 spectral lines of MgIII. Data are presented for an electron density of 1017 cm?3 and temperatures T = 0.5?10.0 (104 K). The matrix elements used in these calculations have been determined from 23 configurations of MgIII: 2s22p6, 2s22p53p, 2s22p54p, 2s22p54f and 2s22p55f for even parity and 2s22p5ns (n = 3?6), 2s22p5nd (n = 3?9), 2s22p55g and 2s2p6np (n = 3?8) for odd parity. For the intermediate coupling (IC) calculations, we use the standard method of least-squares fitting from experimental energy levels by means of the Cowan computer code. Also, in order to test the matrix elements used in our calculations, we present calculated values of 70 transition probabilities of MgIII spectral lines and 14 calculated values of radiative lifetimes of MgIII levels. There is good agreement between our calculations and experimental radiative lifetimes. Spectral lines of MgIII are relevant in astrophysics and also play an important role in the spectral analysis of laboratory plasma. Theoretical trends of the Stark broadening parameter versus the temperature for relevant lines are presented. No values of Stark parameters can be found in the bibliography.

On-line measurement of soil properties without direct spectral response in near infrared spectral range

So far, the majority of reports on on-line measurement considered soil properties with direct spectral responses in near infrared spectroscopy (NIRS). This work reports on the results of on-line measurement of soil properties with indirect spectral responses, e.g. pH, cation exchange capacity (CEC), exchangeable calcium (Caex) and exchangeable magnesium (Mgex) in one field in Bedfordshire in the UK. The on-line sensor consisted of a subsoiler coupled with an AgroSpec mobile, fibre type, visible and near infrared (vis–NIR) spectrophotometer (tec5 Technology for Spectroscopy, Germany), with a measurement range 305–2200 nm to acquire soil spectra in diffuse reflectance mode. General calibration models for the studied soil properties were developed with a partial least squares regression (PLSR) with one-leave-out cross validation, using spectra measured under non-mobile laboratory conditions of 160 soil samples collected from different fields in four farms in Europe, namely, Czech Republic, Denmark, Netherland and UK. A group of 25 samples independent from the calibration set was used as independent validation set. Higher accuracy was obtained for laboratory scanning as compared to on-line scanning of the 25 independent samples. The prediction accuracy for the laboratory and on-line measurements was classified as excellent/very good for pH (RPD = 2.69 and 2.14 and r2 = 0.86 and 0.78, respectively), and moderately good for CEC (RPD = 1.77 and 1.61 and r2 = 0.68 and 0.62, respectively) and Mgex (RPD = 1.72 and 1.49 and r2 = 0.66 and 0.67, respectively). For Caex, very good accuracy was calculated for laboratory method (RPD = 2.19 and r2 = 0.86), as compared to the poor accuracy reported for the on-line method (RPD = 1.30 and r2 = 0.61). The ability of collecting large number of data points per field area (about 12,800 point per 21 ha) and the simultaneous analysis of several soil properties without direct spectral response in the NIR range at relatively high operational speed and appreciable accuracy, encourage the recommendation of the on-line measurement system for site specific fertilisation.

Horizontal to vertical spectral ratio measurements in Port-au-Prince (Haiti) area damaged by the 2010 Haiti earthquake

In order to evaluate ground shaking characteristics due to surface soil layers in the urban area of Port-au-Prince, short-period ambient noise observation has been performed approximately in a 500x500m grid. The HVSR method was applied to this set of 36 ambient noise measurement points to determine a distribution map of soil predominant periods. This map reveals a general increasing trend in the period values, from the Miocene conglomerates in the northern and southern parts of the town to the central and western zones formed of Pleistocene and Holocene alluvial deposits respectively, where the shallow geological materials that cover the basement increase in thickness. Shorter predominant periods (less than 0.3 s) were found in mountainous and neighbouring zones, where the thickness of sediments is smaller whereas longer periods (greater than 0.5 s) appear in Holocene alluvial fans, where the thickness of sediments is larger. The shallow shear-wave velocity structure have been estimated by means of inversion of Rayleigh wave dispersion data obtained from vertical-component array records of ambient noise. The measurements were carried out at one open space located in Holocene alluvial deposits, using 3 regular pentagonal arrays with 5, 10 and 20m respectively. Reliable dispersion curves were retrieved for frequencies between 4.0 and 14 Hz, with phase velocity values ranging from 420m/s down to 270 m/s. Finally, the average shear-wave velocity of the upper 30 m (VS30) was inverted for characterization of this geological unit.

A generalized method for flat plates impact detection and location

In the last years, many analyses from acoustic signal processing have been used for different applications. In most cases, these sensor systems are based on the determination of times of flight for signals from every transducer. This paper presents a flat plate generalization method for impact detection and location over linear links or bars-based structures. The use of three piezoelectric sensors allow to achieve the position and impact time while the use of additional sensors lets cover a larger area of detection and avoid wrong timing difference measurements. An experimental setup and some experimental results are briefly presented.

Debonding detection of FRP strengthened concrete beams by using impedance measurements and an ensemble PSO adaptive spectral model

An impedance-based midspan debonding identification method for RC beams strengthened with FRP strips is presented in this paper using piezoelectric ceramic (PZT) sensor?actuators. To reach this purpose, firstly, a two-dimensional electromechanical impedance model is proposed to predict the electrical admittance of the PZT transducer bonded to the FRP strips of an RC beam. Considering the impedance is measured in high frequencies, a spectral element model of the bonded-PZT?FRP strengthened beam is developed. This model, in conjunction with experimental measurements of PZT transducers, is used to present an updating methodology to quantitatively detect interfacial debonding of these kinds of structures. To improve the performance and accuracy of the detection algorithm in a challenging problem such as ours, the structural health monitoring approach is solved with an ensemble process based on particle of swarm. An adaptive mesh scheme has also been developed to increase the reliability in locating the area in which debonding initiates. Predictions carried out with experimental results have showed the effectiveness and potential of the proposed method to detect prematurely at its earliest stages a critical failure mode such as that due to midspan debonding of the FRP strip.

Identification of the method to quantify soluble fibre and the effect of the source of fibre on the ileal and faecal digestibility of soluble and insoluble fibre in rabbits = Identificación del método para cuantificar la fibra soluble y el efecto de la fuente de fibra en la digestibilidad ileal y fecal de la fibra soluble e insoluble en conejos

La presente tesis constituye un avance en el estudio de los métodos para cuantificar la fibra soluble y los efectos de las fracciones de fibra y las fuentes de fibra sobre la digestión de las diferentes fracciones de fibra (soluble e insoluble) en el conejo. Hay un efecto positivo de la fibra soluble sobre la salud intestinal de los conejos y, por ende, una reducción de la mortalidad en animales destetados. Pese a esto, no está claro si estos efectos se deben específicamente a la fracción soluble. Por lo que los objetivos generales de esta tesis fueron: 1) comparar diferentes metodologías químicas e in vitro para cuantificar la fibra soluble y estudiar las posibles interferencias en la cuantificación de la fibra soluble por las mucinas, y viceversa, 2) determinar los efectos de la fibra, el lugar de fermentación, el método para valorar la fibra soluble e insoluble, y la corrección de la fibra soluble por el contenido intestinal de mucinas sobre la digestibilidad de las distintas fracciones de la fibra y 3) evaluar los efectos individuales de las fracciones soluble e insoluble de la fibra de pulpa de remolacha y de manzana, sobre la digestibilidad de la fibra soluble e insoluble y los parámetros digestivos. Para ello se llevaron a cabo 4 estudios. En el primer estudio se compararon diferentes metodologías químicas e in vitro para valorar la fibra soluble de diferentes alimentos y se estudió la posible interferencia en la determinación de la fibra soluble y mucinas. Para ello se utilizaron seis ingredientes (pulpa de remolacha, pectinas de pulpa de remolacha, pulpa de remolacha lavada, paja de cereal, cascarilla de girasol y lignocelulosa) y siete piensos de conejos con diferentes niveles de fibra soluble. En un primer experimento se analizó la fibra dietética total (FDT), la fibra dietética insoluble (FDI), la fibra dietética soluble (FDS), la fibra neutro detergente corregida por cenizas y proteínas (aFNDmo-pb), y la digestibilidad in vitro 2 pasos pepsina/pancreatina (residuo corregido por cenizas y proteína, ivMSi2) de los ingredientes y piensos. Además la fibra soluble se calculó mediante la diferencia entre FDT-FDI (FDSFDI), FDT- ivMSi2 (FDSivMSi2), y FDT - aFNDmo-pb (FDSaFNDmo-pb). Cuando la fibra soluble se determinó directamente como FDS o se calculó como FDT-FDI no se observaron diferencias (109 g/kg MS, en promedio). Sin embargo, cuando la fibra soluble se calculó como FDT - aFNDmo-pb su valor fue un 40% menor (153 g/kg MS. P < 0,05), mientras que la FDSFDI (124 g/kg MS) no fue diferente a ninguna de las otras metodologías. La correlación entre los tres métodos fue elevada (r > 0,96. P < 0,001. n = 13), pero disminuyó o incluso desapareció cuando la pulpa o las pectinas de la remolacha fueron excluidas del análisis. En un segundo experimento, se comparó el método ivDMi2 usando crisoles (método de referencia) con una modificación del mismo usando bolsas ANKOM digeridas individualmente o en colectivo para simplificar la determinación de la FDSivMSi2. La FDSivMSi2 no difirió entre los métodos comparados. En un tercer experimento, se analizó la posible interferencia entre la determinación de la fibra soluble y las mucinas intestinales. Se observó un contenido de FDT y de mucinas elevado en las muestras de pectinas de remolacha (994 y 709 g/kg MS), así como en el moco intestinal de conejo (571 y 739 g/kg MS) cuando se aplicó el método de mucinas por precipitación con etanol. Sin embargo, después de aplicar una pectinasa en el material precipitado, la cantidad de mucinas recuperadas en las muestras de pectinas de remolacha fue cercana a cero, mientras que en el moco intestinal fue similar a los resultados previos al uso de la enzima. Con los resultados de este ensayo se estimaron los carbohidratos de mucinas retenidos en los contenidos digestivos y se propuso una corrección para la determinación de la digestibilidad de la FDT y fibra soluble. En conclusión, la contaminación de las mucinas de la digesta con fibra soluble se soluciona usando pectinasas. El segundo estudio se centró en estudiar: 1) el efecto del tipo de fibra, 2) el sitio de fermentación, 3) el método para cuantificar fibra y 4) la corrección por mucinas sobre la digestibilidad de la fibra. Para ello se formularon tres piensos con diferentes niveles de fibra soluble (FDT-aFNDmo-pb). Un pienso bajo en fibra soluble (LSF. 85 g/kg DM), un pienso medio en fibra soluble (MSF. 102 g/kg DM), y un pienso alto en fibra soluble (HSF. 145 g/kg DM). Estos piensos se obtuvieron reemplazando un 50% del heno del alfalfa en el pienso MSF por una mezcla de pulpa de manzana y remolacha (HSF) o por una mezcla de cascarilla de avena y proteína de soja (LSF). Se utilizaron 30 conejas canuladas para determinar la digestibilidad ileal y fecal. La digestibilidad cecal se calculó mediante diferencia entre la digestibilidad fecal e ileal. La fibra insoluble se determinó como aFNDmo-pb, IDF, e ivMSi2, mientras que la fibra soluble se calculó como FDSFDI, FDSaFNDmo-pb, y FDSivMSi2. La digestibilidad de la FDT y la fibra soluble se corrigieron por las mucinas. La concentración de mucinas en la digesta ileal y fecal, aumento desde el grupo LSF hasta el grupo con el pienso HSF (P < 0,01). La corrección por mucinas aumentó las digestibilidades de la FDT y la fibra soluble a nivel ileal, mientras que a nivel cecal las redujo. (P < 0.01). El coeficiente de digestibilidad ileal de FDT aumentó desde el grupo LSF al grupo HSF (0,12 vs. 0,281. P < 0,01), sin diferencias en el coeficiente de digestibilidad cecal (0,264), por lo que la tendencia a nivel fecal entre los grupos se mantuvo. El coeficiente de digestibilidad ileal de la fibra insoluble aumento desde el grupo con el pienso LSF al grupo con el pienso HSF (0,113 vs. 0,210. P < 0,01), sin diferencias a nivel cecal (0,139) y sin efecto del método usado, resultando en una digestibilidad elevada a nivel fecal, con tendencias similares a las observadas a nivel ileal. El coeficiente de digestibilidad de la FND fue elevada en comparación con la FDI o la ivMSi2 (P > 0.01). El coeficiente de la digestibilidad ileal de la fibra soluble fue mayor en el grupo LSF respecto al grupo LSF (0,436 vs. 0,145. P < 0,01) y el método no afectó a esta determinación. El coeficiente de la digestibilidad cecal de la fibra soluble se redujo desde el grupo LSF hasta el grupo HSF (0,721 vs. 0,492. P < 0,05). El valor más bajo de digestibilidad cecal y fecal de fibra soluble fue medido con el método FDSaFNDmo-pb (P < 0,01). Se observó una alta correlación entre las digestibilidades de la fibra soluble determinada como FDSFDI, FDSaFNDmo-pb, y FDSivMSi2, por lo tanto la información proporcionada por una u otra metodología fueron similares. Sin embargo, cuando se compararon con efectos fisiológicos (producción de mucinas y peso del ciego y pH del ciego de un trabajo previo), la FDSaFNDmo-pb globalmente mostró estar mejor correlacionado con estos parámetros fisiológicos. En conclusión, la corrección por mucinas es necesaria para determinar la digestibilidad ileal de la FDT y fibra soluble, mientras que la elección de uno u otro método es menos relevante. La inclusión de pulpa de manzana y remolacha incrementa la cantidad de FDT que desaparece antes de llegar al ciego. En el tercer estudio se estudió el efecto de la fracción fibrosa soluble e insoluble de la pulpa de remolacha y el método de cuantificación de la fibra soluble e insoluble sobre la digestibilidad de la fibra y algunos parámetros digestivos. Para ello se formularon cuatro piensos con niveles similares de fibra insoluble (315g aFNDmo-pb/kg MS) y proteína (167 g/kg MS). El pienso control contuvo el nivel más bajo de fibra soluble (30,3 g/kg, con cascarilla de girasol y paja como fuente de fibra). Un segundo pienso se obtuvo mediante la sustitución de 60 g de almidón/kg del pienso control por pectinas de remolacha (82,9 g fibra soluble/kg MS). Los otras dos piensos resultaron de la sustitución parcial de las fuentes de fibra del pienso control por la fracción insoluble de la pulpa de remolacha y la pulpa de remolacha entera (42.2 y 82.3 g fibra soluble/kg MS, respectivamente). Cincuenta y seis conejos en cebo (14/pienso), de 2,4  0.21 kg de peso, fueron usados para determinar la digestibilidad ileal y fecal de la FDT, FDI, aFNDmo-pb, FDSFDI, y FDSaFNDmo-pb. La concentración de mucinas en el íleon y heces se utilizaron para corregir la digestibilidad de la FDT y fibra soluble. También se midió el peso de diferentes segmentos del tracto digestivo y el pH del contenido digestivo. Los conejos alimentados con el pienso de fibra insoluble de pulpa de remolacha mostraron los consumos más bajos con respecto a los demás grupos (124 vs. 139 g/d, respectivamente. P < 0,05). El flujo de mucinas ileales fue más alto (P < 0.05) en el grupo alimentado con el pienso de pectinas de remolacha (9,0 g/d en promedio) que los del grupo control (4,79 g/d), mostrando los otros dos grupos valores intermedios, sin detectarse diferencias a nivel fecal. La digestibilidad ileal de la FDT (corregida por mucinas) y la fibra insoluble no se vieron afectadas por el tipo de pienso. El método usado para determinar la fibra insoluble afectó su digestibilidad ileal (0,123 para FDI vs. 0,108 para aFNDmo-pb. P < 0.01). De todas formas, los métodos no afectaron al cálculo de la fibra fermentada antes del ciego (4,9 g/d en promedio). Los conejos alimentados con el pienso de pulpa de remolacha y con el pienso con la fracción insoluble de la pulpa de remolacha mostraron las digestibilidades fecales más altas de la fibra insoluble (0,266 en promedio vs. 0,106 del grupo control), mientras que en los animales del pienso con pectinas esta digestibilidad fue un 47% mayor respecto al pienso control (P < 0,001). La digestibilidad fecal de la fibra insoluble fue un 20% más alta cuando se usó la FND en lugar de FDI para determinarla (P < 0.001). Esto hizo variar la cantidad de fibra insoluble fermentada a lo largo del tracto digestivo (9,5 ó 7,5 g/d cuando fue calculada como FDI o aFNDmo-pb, respectivamente. P < 0,001). Las digestibilidades ileales de la fibra soluble fueron positivas cuando los análisis de fibra soluble de los contenidos ileales fueron corregidos por mucinas, (P < 0,001) excepto para la digestibilidad ileal de la FDSIDF del grupo control. Una vez corregidas por mucinas, los conejos alimentados con los piensos que contuvieron la fracción soluble de la pulpa de remolacha (pienso de pectina y pulpa de remolacha) mostraron una mayor digestibilidad ileal de la fibra soluble, respecto al grupo control (0,483 vs. -0,010. P = 0.002), mientras que el grupo del pienso de fibra insoluble de pulpa de remolacha mostró un valor intermedio (0,274). La digestibilidad total de la fibra soluble fue similar entre todos los grupos (0.93). Los conejos alimentados con pulpa de remolacha y su fracción insoluble mostraron los pesos relativos más altos del estómago respecto a los del pienso control y de pectinas (11 y 56 % respectivamente; P < 0,05). Por otra parte, el peso relativo del ciego aumentó en los animales que consumieron tanto la fracción soluble como insoluble de la pulpa de remolacha, siendo un 16% más pesados (P < 0,001) que el grupo control. El pH del contenido cecal fue más bajo en los animales del grupo de pulpa de remolacha que en los del grupo control (5,64 vs. 6,03; P < 0,001), mientras que los del grupo de pectinas y de fibra insoluble de pulpa de remolacha mostraron valores intermedios. En conclusión, el efecto positivo de la pulpa de remolacha en el flujo de mucinas a nivel ileal se debe a la fracción soluble e insoluble de la pulpa de remolacha. La mitad de la fibra soluble de la pulpa de remolacha desaparece antes de llegar al ciego, independientemente si esta proviene de pectinas puras o de la pulpa de remolacha. El pH cecal esta mejor correlacionado con la cantidad de FDT que desaparece antes del ciego más que con la que se degrada en el ciego. En el último estudio se estudiaron los efectos de la fibra soluble e insoluble de la pulpa de manzana sobre la digestibilidad de la fibra y algunos parámetros digestivos. Cuatro dietas fueron formuladas con niveles similares de fibra insoluble (aFNDmo-pb 32,4%) y proteína (18,6% ambos en base seca). El pienso control contuvo el nivel más bajo de fibra soluble (46 g de fibra soluble/kg, con cascarilla de girasol y paja de cereales como la fuentes de fibra). Un segundo pienso fue obtenido mediante la sustitución de 60 g de almidón/kg del pienso control por pectinas de manzana (105 g fibra soluble/kg). Los otros dos piensos se obtuvieron por la substitución de parte de las fuentes de fibra del pienso control por pulpa de manzana o pulpa de manzana despectinizada (93 y 71 g de fibra soluble/kg, respectivamente). La digestibilidad fecal fue determinada en 23 conejos/pienso con 1.68 ± 0.23 kg de peso vivo, los cuales fueron sacrificados a los 60 d edad para recolectar su contenido digestivo para determinar digestibilidad ileal y otros parámetros digestivos. La fibra soluble de manzana (pectinas y pulpa entera) estimuló el flujo ileal de mucinas (P = 0,002), pero no asi la pulpa despectinizada. La corrección por mucinas incrementó la digestibilidad de la FDT y la fibra soluble a nivel fecal, y especialmente a nivel ileal. Cerca de la mitad de la fibra soluble proveniente de los piensos con cualquiera de las fracciones de la pulpa de manzana fue degradada a nivel ileal, sin mostrar diferencias entre los grupos (46 y 86% en promedio a nivel ileal y fecal respectivamente). La inclusión de pulpa despectinizada de manzana mejoró la digestibilidad de la FND a nivel fecal (P < 0,05) pero no a nivel ileal. El contenido cecal de los conejos alimentados con la pulpa de manzana tuvieron el pH cecal más ácido que los del pienso control (5,55 vs. 5,95. P < 0,001), mientras que los animales con el pienso de pectinas de manzana y de pulpa de manzana despectinizada mostraron valores intermedios. En conclusión los efectos positivo de la pulpa de manzana en el flujo de mucinas se debió principalmente a la fracción soluble de la pulpa de manzana. La mitad de la fibra soluble fue degradada antes del ciego independientemente de si esta provino de las pectinas o de la pulpa de manzana. El pH cecal estuvo mejor correlacionado con la cantidad de FDT fermentada en todo el tracto digestivo y antes de llegar al ciego que con la que se degradó en el ciego. Al integrar los resultados de los estudio 2, 3 y 4 se concluyó que la corrección de mucinas de los contenidos digestivos al determinar FDT y fibra soluble es necesaria para ajustar los cálculos de su digestibilidad. Esta corrección es mucho más importante a nivel ileal y en dietas bajas en fibra soluble. Por otra parte, la FDT desapareció en proporciones importantes antes de llegar al ciego, especialmente en piensos que contienen pulpa de remolacha o de manzana o alguna fracción soluble o insoluble de las mismas y estas diferencias observadas entre los piensos a nivel ileal se correlacionaron mejor con el pH cecal, lo que indicaría que la FDT se solubilizó antes de llegar al ciego y una vez en esté fermentó. Estos resultados implican que determinar la fibra soluble como FDSaFNDmo-pb es la mejor opción y que en la determinación de la digestibilidad de la FDT y fibra soluble se debe considerar la corrección por mucinas especialmente a nivel ileal y en piensos bajos en fibra soluble. ABSTRACT The present thesis constitutes a step forward in advancing the knowledge of the methods to quantify soluble fibre and the effects of the fibre fractions and source of fibre on the site the digestion of different fractions of fibre (soluble and insoluble) in the rabbit. There is a positive effect of soluble fibre on rabbit digestive health and therefore on the reduction of mortality in weaning rabbits. Nevertheless, it is no so clear that the effects of soluble fibre on rabbits are due particularly to this fraction. This thesis aims: 1) to compare the quantification of soluble fibre in feeds using different chemical and in vitro approaches, and to study the potential interference between soluble fibre and mucin determinations, 2) to identify the effects of type of fibre, site of fermentation, method to quantify insoluble and soluble fibre, and correction of the intestinal soluble fibre content for intestinal mucin on the digestibility of fibre fractions and 3) to evaluate the individual effect of soluble and insoluble fibre from sugar beet pulp and apple pulp on ileal and faecal soluble and insoluble digestibility and digestive traits. These objectives were developed in four studies: The first study compared the quantification of soluble fibre in feeds using different chemical and in vitro approaches, and studied the potential interference between soluble fibre and mucin determinations. Six ingredients, sugar beet pulp (SBP), SBP pectins, insoluble SBP, wheat straw, sunflower hulls and lignocellulose, and seven rabbit diets, differing in soluble fibre content, were evaluated. In experiment 1, ingredients and diets were analysed for total dietary fibre (TDF), insoluble dietary fibre (IDF), soluble dietary fibre (SDF), aNDFom (corrected for protein, aNDFom-cp) and 2-step pepsin/pancreatin in vitro DM indigestibility (corrected for ash and protein, ivDMi2). Soluble fibre was estimated by difference using three procedures: TDF - IDF (SDFIDF), TDF - ivDMi2 (SDFivDMi2), and TDF - aNDFom-cp (SDFaNDFom-cp). Soluble fibre determined directly (SDF) or by difference, as SDFivDMi2 were not different (109 g/kg DM, on average). However, when it was calculated as SDFaNDFom-cp the value was 40% higher (153 g/kg DM, P < 0.05), whereas SDFIDF (124 g/kg DM) did not differ from any of the other methods. The correlation between the four methods was high (r ≥ 0.96. P ≤ 0.001. n = 13), but it decreased or even disappeared when SBP pectins and SBP were excluded and a lower and more narrow range of variation of soluble fibre was used. In experiment 2, the ivDMi2 using crucibles (reference method) were compared to those made using individual or collective ankom bags in order to simplify the determination of SDFivDMi2. The ivDMi2 was not different when using crucibles or individual or collective ankom bags. In experiment 3, the potential interference between soluble fibre and intestinal mucin determinations was studied using rabbit intestinal raw mucus, digesta and SBP pectins, lignocelluloses and a rabbit diet. An interference was observed between the determinations of soluble fibre and crude mucin, as the content of TDF and apparent crude mucin were high in SBP pectins (994 and 709 g/kg DM) and rabbit intestinal raw mucus (571 and 739 g/kg DM). After a pectinase treatment, the coefficient of apparent mucin recovery of SBP pectins was close to zero, whereas that of rabbit mucus was not modified. An estimation of the crude mucin carbohydrates retained in digesta TDF is proposed to correct TDF and soluble fibre digestibility. In conclusion, the values of soluble fibre depend on the methodology used. The contamination of crude mucin with soluble fibre is avoided using pectinase. The second study focused on the effect of type of fibre, site of fermentation, method for quantifying insoluble and soluble dietary fibre, and their correction for intestinal mucin on fibre digestibility. Three diets differing in soluble fibre were formulated (85 g/kg DM soluble fibre, in the low soluble fibre [LSF] diet; 102 g/kg DM in the medium soluble fibre [MSF] diet; and 145 g/kg DM in the high soluble fibre [HSF] diet). They were obtained by replacing half of the dehydrated alfalfa in the MSF diet with a mixture of beet and apple pulp (HSF diet) or with a mix of oat hulls and soybean protein (LSF diet). Thirty rabbits with ileal T-cannulas were used to determine total tract apparent digestibility (CTTAD) and ileal apparent digestibility (CIAD). Caecal digestibility was determined by difference between CTTAD and CIAD. Insoluble fibre was measured as aNDFom-cp, IDF, and ivDMi2, whereas soluble fibre was calculated as SDFaNDFom-cp, SDFIDF, SDFivDMi2. The intestinal mucin content was used to correct the TDF and soluble fibre digestibility. Ileal and faecal concentration of mucin increased from the LSF to the HSF diet group (P < 0.01). Once corrected for intestinal mucin, The CTTAD and CIAD of TDF and soluble fibre increased whereas caecal digestibility decreased (P < 0.01). The CIAD of TDF increased from the LSF to the HSF diet group (0.12 vs. 0.281. P < 0.01), with no difference in the caecal digestibility (0.264), resulting in a higher CTTAD from the LSF to the HSF diet group (P < 0.01). The CIAD of insoluble fibre increased from the LSF to the HSF diet group (0.113 vs. 0.21. P < 0.01), with no difference in the caecal digestibility (0.139) and no effect of fibre method, resulting in a higher CTTAD for rabbits fed the HSF diet compared with the MSF and LSF diets groups (P < 0.01). The CTTAD of aNDFom-cp was higher compared with IDF or ivDMi2 (P < 0.01). The CIAD of soluble fibre was higher for the HSF than for the LSF diet group (0.436 vs. 0.145. P < 0.01) and fibre method did not affect it. Caecal soluble fibre digestibility decreased from the LSF to the HSF diet group (0.721 vs. 0.492. P < 0.05). The lowest caecal and faecal soluble fibre digestibility was measured using SDFaNDFom-cp (P < 0.01). There was a high correlation among the digestibilities of soluble fibre measured as SDFaNDFom-cp, SDFIDF, and SDFivDMi2. Therefore, these methodologies provide similar information. However, the method that seems to be globally better related to the physiological traits (ileal flow of mucins, and relative weight of the caecum and caecal pH from previous work) was the SDFaNDFom-cp. In conclusion, a correction for intestinal mucin is necessary for ileal TDF and soluble fibre digestibility whereas the selection of the fibre method has a minor relevance. The inclusion of sugar beet and apple pulp increased the amount of TDF fermented in the small intestine. The third study examined the effect of fibre fractions of sugar beet pulp (SBP) and the method for quantifying soluble and insoluble fibre on soluble and insoluble fibre digestibility and digestive traits. Four diets were formulated with similar level of insoluble fibre (aNDFom-cp: 315 g/kg DM) and protein (167 g/kg DM). Control diet contained the lowest level of soluble fibre (30.3 g/kg DM, including sunflower hulls and straw as sole sources of fibre). A second diet was obtained by replacing 60 g starch/kg of control diet with SBP pectins (82.9 g soluble fibre/kg DM). Two more diets were obtained by replacing part of the fibrous sources of the control diet with either insoluble SBP fibre or SBP (42.2 and 82.3 g soluble fibre/kg DM, respectively). Fifty six (14/diet) rabbits weighing 2.40  0.213 kg were used to determine faecal and ileal digestibility of total dietary fibre (TDF), insoluble dietary fibre (IDF), neutral detergent fibre corrected for ash and CP (aNDFom-cp) and soluble fibre estimated as SDFaNDFom-cp and SDFIDF. Faecal and ileal mucin content was used to correct TDF and soluble fibre digestibility. It was also recorded weight of digestive segments and digesta pH. Rabbits fed insoluble SBP showed the lowest feed intake with respect to the other 3 diets (124 vs. 139 g/d, respectively. P < 0.05). Ileal mucin flow was higher (P < 0.05) in animals fed pectin and SBP diets (9.0 g/d, as average) than those fed control diet (4.79 g/d), showing InsSBP group an intermediate value. No differences on mucin content were detected at faecal level. There was no diet effect on the CIAD of TDF (corrected for mucin) and insoluble fibre. Fibre methodology influenced the CIAD of insoluble fibre (0.123 for IDF vs. 0.108 for aNDFom-cp. P < 0.01). Anyway, the amount of insoluble fibre fermented before the caecum did not differ between both methods (4.9 g/d, on average). Rabbits fed insoluble SBP and SBP diets showed the highest CTTAD of insoluble fibre (0.266 on average vs. 0.106 for control group), whereas those fed pectin diet had an intermediate value (0.106. P < 0.001). The CTTAD of insoluble fibre measured with IDF was higher than that measured with aNDFom-cp (by 20%. P < 0.001). It led that the amount of insoluble fibre fermented along the digestive tract were different (9.5 or 7.5 g/d when calculated as IDF or aNDFom-cp, respectively; P < 0.001). When the CIAD of soluble fibre was corrected for mucin they became positive (P < 0.001) except for control group measured as SDFIDF. Once corrected for mucin content, rabbits fed soluble fibre from SBP (pectin and SBP groups) showed higher CIAD of soluble fibre than control group (0.483 vs. -0.019. respectively), whereas the value for insoluble SBP group was intermediate 0.274. The CTTAD of soluble fibre (mucin corrected) was similar among diets 0.93. Rabbits fed with SBP and insoluble SBP diets showed higher total digestive tract and stomach relative weight than those fed pectin and control diets (by 11 and 56 %. respectively, P < 0.05). The caecal relative weight did not differ in rabbits fed pectin, insoluble SBP, and SBP diets (62 g/kg BW, as average) and they were on average 16% higher (P < 0.001) than in control group. Caecal content of rabbits fed SBP diet was more acid than those fed control diet (5.64 vs. 6.03. P < 0.001), whereas those from pectin and insoluble SBP diets showed intermediate values. In conclusion, the positive effect of SBP fibre on ileal mucin flow was due to both its soluble and insoluble fibre fraction. Half of the soluble SBP fibre was degraded before the caecum independently it came from pectin or SBP. The caecal pH correlated better with the ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. The last study examined the effect of soluble and insoluble fibre of apple pulp on fibre digestibility and digestive traits. Four diets were formulated with similar level of insoluble fibre (aNDFom-cp: 324 g/kg DM) and protein (18.6 g/kg DM). Control diet contained the lowest level of soluble fibre (46 g soluble fibre/kg DM, including oat hulls and straw as sole sources of fibre). A second diet was obtained by replacing 60 g starch/kg of control diet with apple pectins (105 g soluble fibre/kg DM). Two more diets were obtained by substituting part of the fibrous sources of the control diet by either apple pulp or depectinized apple pulp (93 and 71 g soluble fibre/kg, respectively). The CTTAD was determined in 23 rabbits/diet weighing 1.68  0.23 kg BW, and 23 rabbits/diet were slaughtered at 60 d of age to collect ileal digesta to determine CIAD and record other digestive traits. Soluble fibre from apple stimulated ileal flow of mucin (P = 0.002), but depectinized apple pulp did not. The correction for mucin increased the digestibility of crude protein, total dietary fibre, and soluble fibre at faecal, but especially at ileal level, depending in this case on the diet. Around half of the soluble fibre in diets containing any fibre fraction from apple was degraded at ileal level, with no differences among these diets (0.46 vs. 0.066 for control group, P=0.046). Faecal soluble fibre digestibility was 0.86 on average for all groups). Inclusion of the apple insoluble fibre improved NDF digestibility at faecal (0.222 vs. 0.069. P < 0.05) but not at ileal level. Caecal content of rabbits fed apple pulp diet was more acid than those fed control diet (5.55 vs. 5.95. P < 0.001), whereas those from pectin and depectinised apple pulp diets showed intermediate values. In conclusion, the positive effect of apple fibre on ileal mucin flow was mainly due to its soluble fibre fraction. Half of the soluble apple fibre was degraded before the caecum independently it came from pectin or apple pulp. The caecal pH correlated better with the total and ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. The results obtained in the studies 2, 3 and 4 were considered together. These results showed that the mucin correction is necessary when the TDF and soluble fibre digestibility is determined, and it correction is more important at ileal level and in diets with low level of soluble fibre. On another hand, incrementing the soluble fibre using sugar beet and apple pulp increased the amount of TDF disappear before the caecum. Moreover, the caecal pH correlated better with the ileal amount of fermented TDF in the digestive tract rather than with that fermented in the caecum. This suggests that an ileal fibre solubilisation may occur rather than ileal fermentation. Therefore the implications of this work were that: the estimation of soluble fibre as SDFaNDFom-cp is an adequate method considering its correlation with the physiological effects; and the TDF and soluble fibre digestibility must be corrected with intestinal mucins, especially when the ileal digestibility is determined.

Modelización de las fallas activas para la estimación de la Peligrosidad Sísmica. Aplicación Metodológica en Haití

The development of this Master's Thesis is aimed at modeling active for estimating seismic hazard in Haití failures. It has been used zoned probabilistic method, both classical and hybrid, considering the incorporation of active faults as independent units in the calculation of seismic hazard. In this case, the rate of seismic moment is divided between the failures and the area seismogenetic same region. Failures included in this study are the Septentrional, Matheux and Enriquillo fault. We compared the results obtained by both methods to determine the importance of considering the faults in the calculation. In the first instance, updating the seismic catalog, homogenization, completeness analysis and purification was necessary to obtain a catalog ready to proceed to the estimation of the hazard. With the seismogenic zoning defined in previous studies and the updated seismic catalog, they are obtained relations Gutenberg-Richter recurrence of seismicity, superficial and deep in each area. Selected attenuation models were those used in (Benito et al., 2011), as the tectonic area of study is very similar to that of Central America. Its implementation has been through the development of a logical in which each branch is multiplied by an index based on the relevance of each combination of models. Results are presented as seismic hazard maps for return periods of 475, 975 and 2475 years, and spectral acceleration (SA) in structural periods: 0.1 - 0.2 - 0.5 - 1.0 and 2.0 seconds, and the difference accelerations between maps obtained by the classical method and the hybrid method. Maps realize the importance of including faults as separate items in the calculation of the hazard. The morphology of the zoned maps presented higher values in the area where the superficial and deep zone overlap. In the results it can determine that the minimum values in the zoned approach they outweigh the hybrid method, especially in areas where there are no faults. Higher values correspond to those obtained in fault zones by the hybrid method understanding that the contribution of the faults in this method is very important with high values. The maximum value of PGA obtained is close to Septentrional in 963gal, near to 460 gal in Matheux, and the Enriquillo fault line value reaches 760gal PGA in the Eastern segment and Western 730gal in the segment. This compares with that obtained in the zoned approach in this area where the value of PGA obtained was 240gal. These values are compared with those obtained by Frankel et al., (2011) with those have much similarity in values and morphology, in contrast to those presented by Benito et al., (2012) and the Standard Seismic Dominican Republic

Contribution to the analysis and design of reflectarray antennas for reconfigurable beam applications at frequencies above 100 GHz using liquid crystal technology

El trabajo contenido en esta tesis doctoral está encuadrado en el desarrollo de antenas reconfigurables electrónicamente capaces de proporcionar prestaciones competitivas a las aplicaciones cada vez más comunes que operan a frecuencias superiores a 60 GHz. En concreto, esta tesis se centra en el estudio, diseño, e implementación de las antenas reflectarray, a las que se introduce la tecnología de cristal líquido como elemento característico con el que se consigue reconfigurabilidad de haz de forma electrónica. Desde un punto de vista muy general, se puede describir un cristal líquido como un material cuya permitividad eléctrica es variable y controlada por una excitación externa, que generalmente suele corresponderse con un campo eléctrico quasi-estático (AC). Las antenas reflectarray de cristal líquido se han escogido como objeto de estudio por varias razones. La primera de ellas tiene que ver con las ventajas que los reflectarrays, y en especial aquellos realizados en configuración planar, proporcionan con respecto a otras antenas de alta ganancia como los reflectores o los “phased-arrays”. En los reflectarrays, la alimentación a través de una fuente primaria común (característica de reflectores) y el elevado número de grados de libertad de las celdas que los componen (característica de arrays) hacen que estas antenas puedan proporcionar prestaciones eléctricas iguales o mejores que las anteriores, a un coste más reducido y con estructuras de antena más compactas. La segunda razón radica en la flexibilidad que ofrece el cristal líquido a ser confinado y polarizado en recintos de geometría variada, como consecuencia de su fluidez (propiedad de los líquidos). Por ello, la tecnología de cristal líquido permite que el propio elemento reconfigurable en las celdas de reflectarray se adapte a la configuración planar de manera que en sí mismo, el cristal líquido sea una o varias de las capas características de esta configuración. Esto simplifica de forma drástica la estructura y la fabricación de este tipo de antenas, incluso si se comparan con reflectarrays reconfigurables basados en otras tecnologías como diodos, MEMS, etc. Por tanto, su coste y desarrollo es muy reducido, lo que hace que se puedan fabricar reflectarrays reconfigurables eléctricamente grandes, a bajo coste, y en producción elevada. Un ejemplo claro de una estructura similar, y que ha tenido éxito comercial, son las pantallas de cristal líquido. La tercera razón reside en el hecho de que el cristal líquido es, hasta la fecha, de las pocas tecnologías capaces de ofrecer reconfigurabilidad del haz a frecuencias superiores a 60 GHz. De hecho, el cristal líquido permite reconfigurabilidad en un amplio margen de frecuencias, que va desde DC a frecuencias del espectro visible, incluyendo las microondas y los THz. Otras tecnologías, como los materiales ferroeléctricos, el grafeno o la tecnología CMOS “on chip” permiten también conmutar el haz en estas frecuencias. Sin embargo, la tecnología CMOS tiene un elevado coste y actualmente está limitada a frecuencias inferiores a 150 GHz, y aunque los materiales ferroeléctricos o el grafeno puedan conmutar a frecuencias más altas y en un rango más amplio, tienen serias dificultades que los hacen aún inmaduros. En el caso de los materiales ferroeléctricos, los elevados voltajes para conmutar el material los hacen poco atractivos, mientras que en el caso del grafeno, su modelado aún está en discusión, y todavía no se han arrojado resultados experimentales que validen su idoneidad. Estas tres razones hacen que los reflectarrays basados en cristal líquido sean atractivos para multitud de aplicaciones de haz reconfigurable a frecuencias superiores a 60 GHz. Aplicaciones como radar de escaneo de imágenes de alta resolución, espectroscopia molecular, radiómetros para observación atmosférica, o comunicaciones inalámbricas de alta frecuencia (WiGig) son algunas de ellas. La tesis está estructurada en tres partes. En la primera de ellas se describen las características más comunes de los cristales líquidos, centrándonos en detalle en aquellas propiedades ofrecidas por este material en fase nemática. En concreto, se estudiará la anisotropía dieléctrica (Ae) de los cristales líquidos uniaxiales, que son los que se emplean en esta tesis, definida como la diferencia entre la permitividad paralela (£//) y la perpendicular (e±): Ae = e,, - e±. También se estudiará la variación de este parámetro (Ae) con la frecuencia, y el modelado electromagnético macroscópico más general que, extraído a partir de aquella, permite describir el cristal líquido para cada tensión de polarización en celdas de geometría planar. Este modelo es de suma importancia para garantizar precisión en el desfasaje proporcionado por las diferentes celdas reconfigurables para reflectarrays que se describirán en la siguiente parte de la tesis. La segunda parte de la tesis se centra en el diseño de celdas reflectarray resonantes basadas en cristal líquido. La razón por la que se escogen estos tipos de celdas reside en el hecho de que son las únicas capaces de proporcionar rangos de fase elevados ante la reducida anisotropía dieléctrica que ofrecen los cristales líquidos. El objetivo de esta parte trata, por tanto, de obtener estructuras de celdas reflectarray que sean capaces de proporcionar buenas prestaciones eléctricas a nivel de antena, mejorando sustancialmente las prestaciones de las celdas reportadas en el estado del arte, así como de desarrollar una herramienta de diseño general para aquellas. Para ello, se estudian las prestaciones eléctricas de diferentes tipos de elementos resonantes de cristal líquido que van, desde el más sencillo, que ha limitado el estado de la técnica hasta el desarrollo de esta tesis y que está formado por un sólo resonador, a elementos que constan de varios resonadores (multi-resonantes) y que pueden ser monocapa o multicapa. En un primer paso, el procedimiento de diseño de estas estructuras hace uso de un modelo convencional de cristal líquido que ha venido siendo usado en el estado del arte para este tipo de celdas, y que considera el cristal líquido como un material homogéneo e isótropo cuya permitividad varía entre (e/7) y (e±). Sin embargo, en esta parte de la tesis se demuestra que dicho modelado no es suficiente para describir de forma genérica el comportamiento del cristal líquido en las celdas tipo reflectarray. En la tesis se proponen procedimientos más exactos para el análisis y diseño basados en un modelo más general que define el cristal líquido como un material anisótropo e inhomogeneo en tres dimensiones, y se ha implementado una técnica que permite optimizar celdas multi-resonantes de forma eficiente para conseguir elevadas prestaciones en cuanto a ancho de banda, rango de fase, pérdidas, o sensibilidad al ángulo de incidencia. Los errores cometidos en el uso del modelado convencional a nivel de celda (amplitud y fase) se han analizado para varias geometrías, usando medidas de varios prototipos de antena que usan un cristal líquido real a frecuencias superiores a 100 GHz. Las medidas se han realizado en entorno periódico mediante un banco cuasi-óptico, que ha sido diseñado especialmente para este fin. Uno de estos prototipos se ha optimizado a 100 GHz para conseguir un ancho de banda relativamente elevado (10%), pérdidas reducidas, un rango de fase mayor de 360º, baja sensibilidad al ángulo de incidencia, y baja influencia de la inhomogeneidad transversal del cristal líquido en la celda. Estas prestaciones a nivel de celda superan de forma clara aquellas conseguidas por otros elementos que se han reportado en la literatura, de manera que dicho prototipo se ha usado en la última parte de la tesis para realizar diversas antenas de barrido. Finalmente, en esta parte se presenta una estrategia de caracterización de la anisotropía macroscópica a partir de medidas de los elementos de reflectarray diseñados en banco cuasi-óptico, obteniendo resultados tanto en las frecuencias de interés en RF como en AC, y comparándolas con aquellas obtenidas mediante otros métodos. La tercera parte de la tesis consiste en el estudio, diseño, fabricación y medida de antenas reconfigurables basadas en cristal líquido en configuraciones complejas. En reflectarrays pasivos, el procedimiento de diseño de la antena se limita únicamente al ajuste en cada celda de la antena de las dimensiones de las metalizaciones que se emplean para el control de fase, mediante procesos de optimización bien conocidos. Sin embargo, en el caso de reflectarrays reconfigurables basados en cristal líquido, resulta necesario un paso adicional, que consiste en calcular de forma adecuada las tensiones de control en cada celda del reflectarray para configurar la fase requerida en cada una de ellas, así como diseñar la estructura y los circuitos de control que permitan direccionar a cada elemento su tensión correspondiente. La síntesis de tensiones es por tanto igual o más importante que el diseño de la geometría de las celdas, puesto que éstas son las que están directamente relacionadas con la fase. En el estado del arte, existen varias estrategias de síntesis de tensiones que se basan en la caracterización experimental de la curva de fase respecto al voltaje. Sin embargo, esta caracterización sólo puede hacerse a un solo ángulo de incidencia y para unas determinadas dimensiones de celda, lo que produce que las tensiones sintetizadas sean diferentes de las adecuadas, y en definitiva que se alcancen errores de fase mayores de 70º. De esta forma, hasta la fecha, las prestaciones a nivel de antena que se han conseguido son reducidas en cuanto a ancho de banda, rango de escaneo o nivel de lóbulos secundarios. En esta última parte de la tesis, se introduce una nueva estrategia de síntesis de tensiones que es capaz de predecir mediante simulaciones, y con alta precisión, las tensiones que deben introducirse en cada celda teniendo en cuenta su ángulo de incidencia, sus dimensiones, la frecuencia, así como la señal de polarización definida por su frecuencia y forma de onda AC. Esta estrategia se basa en modelar cada uno de los estados de permitividad del cristal líquido como un sustrato anisótropo con inhomogeneidad longitudinal (1D), o en ciertos casos, como un tensor equivalente homogéneo. La precisión de ambos modelos electromagnéticos también se discute. Con el objetivo de obtener una herramienta eficiente de cálculo de tensiones, también se ha escrito e implementado una herramienta de análisis basada en el Método de los Momentos en el Dominio Espectral (SD-MoM) para sustratos estratificados anisótropos, que se usa en cada iteración del procedimiento de síntesis para analizar cada una de las celdas de la antena. La síntesis de tensiones se ha diseñado además para reducir al máximo el efecto del rizado de amplitud en el diagrama de radiación, que es característico en los reflectarrays que están formados por celdas con pérdidas elevadas, lo que en sí, supone un avance adicional para la obtención de mejores prestaciones de antena. Para el cálculo de los diagramas de radiación empleados en el procedimiento de síntesis, se asume un análisis elemento a elemento considerando periodicidad local, y se propone el uso de un método capaz de modelar el campo incidente de forma que se elimine la limitación de la periodicidad local en la excitación. Una vez definida la estrategia adecuada de cálculo de las tensiones a aplicar al cristal líquido en cada celda, la estructura de direccionamiento de las mismas en la antena, y diseñados los circuitos de control, se diseñan, fabrican y miden dos prototipos diferentes de antena de barrido electrónico a 100 GHz usando las celdas anteriormente presentadas. El primero de estos prototipos es un reflectarray en configuración “single offset” con capacidad de escaneo en un plano (elevación o azimut). Aunque previamente se realizan diseños de antenas de barrido en 2D a varias frecuencias en el rango de milimétricas y sub-milimétricas, y se proponen ciertas estrategias de direccionamiento que permiten conseguir este objetivo, se desarrolla el prototipo con direccionamiento en una dimensión con el fin de reducir el número de controles y posibles errores de fabricación, y así también validar la herramienta de diseño. Para un tamaño medio de apertura (con un numero de filas y columnas entre 30 y 50 elementos, lo que significa un reflectarray con un número de elementos superior a 900), la configuración “single offset” proporciona rangos de escaneo elevados, y ganancias que pueden oscilar entre los 20 y 30 dBi. En concreto, el prototipo medido proporciona un haz de barrido en un rango angular de 55º, en el que el nivel de lóbulos secundarios (SLL) permanece mejor de -13 dB en un ancho de banda de un 8%. La ganancia máxima es de 19.4 dBi. Estas prestaciones superan de forma clara aquellas conseguidas por otros autores. El segundo prototipo se corresponde con una antena de doble reflector que usa el reflectarray de cristal líquido como sub-reflector para escanear el haz en un plano (elevación o azimut). El objetivo básico de esta geometría es obtener mayores ganancias que en el reflectarray “single offset” con una estructura más compacta, aunque a expensas de reducir el rango de barrido. En concreto, se obtiene una ganancia máxima de 35 dBi, y un rango de barrido de 12º. Los procedimientos de síntesis de tensiones y de diseño de las estructuras de las celdas forman, en su conjunto, una herramienta completa de diseño precisa y eficiente de antenas reflectarray reconfigurables basados en cristales líquidos. Dicha herramienta se ha validado mediante el diseño, la fabricación y la medida de los prototipos anteriormente citados a 100 GHz, que consiguen algo nunca alcanzado anteriormente en la investigación de este tipo de antenas: unas prestaciones competitivas y una predicción excelente de los resultados. El procedimiento es general, y por tanto se puede usar a cualquier frecuencia en la que el cristal líquido ofrezca anisotropía dieléctrica, incluidos los THz. Los prototipos desarrollados en esta tesis doctoral suponen también unas de las primeras antenas de barrido real a frecuencias superiores a 100 GHz. En concreto, la antena de doble reflector para escaneo de haz es la primera antena reconfigurable electrónicamente a frecuencias superiores a 60 GHz que superan los 25 dBi de ganancia, siendo a su vez la primera antena de doble reflector que contiene un reflectarray reconfigurable como sub-reflector. Finalmente, se proponen ciertas mejoras que aún deben se deben realizar para hacer que estas antenas puedan ser un producto completamente desarrollado y competitivo en el mercado. ABSTRACT The work presented in this thesis is focused on the development of electronically reconfigurable antennas that are able to provide competitive electrical performance to the increasingly common applications operating at frequencies above 60 GHz. Specifically, this thesis presents the study, design, and implementation of reflectarray antennas, which incorporate liquid crystal (LC) materials to scan or reconfigure the beam electronically. From a general point of view, a liquid crystal can be defined as a material whose dielectric permittivity is variable and can be controlled with an external excitation, which usually corresponds with a quasi-static electric field (AC). By changing the dielectric permittivity at each cell that makes up the reflectarray, the phase shift on the aperture is controlled, so that a prescribed radiation pattern can be configured. Liquid Crystal-based reflectarrays have been chosen for several reasons. The first has to do with the advantages provided by the reflectarray antenna with respect to other high gain antennas, such as reflectors or phased arrays. The RF feeding in reflectarrays is achieved by using a common primary source (as in reflectors). This arrangement and the large number of degrees of freedom provided by the cells that make up the reflectarray (as in arrays), allow these antennas to provide a similar or even better electrical performance than other low profile antennas (reflectors and arrays), but assuming a more reduced cost and compactness. The second reason is the flexibility of the liquid crystal to be confined in an arbitrary geometry due to its fluidity (property of liquids). Therefore, the liquid crystal is able to adapt to a planar geometry so that it is one or more of the typical layers of this configuration. This simplifies drastically both the structure and manufacture of this type of antenna, even when compared with reconfigurable reflectarrays based on other technologies, such as diodes MEMS, etc. Therefore, the cost of developing this type of antenna is very small, which means that electrically large reconfigurable reflectarrays could be manufactured assuming low cost and greater productions. A paradigmatic example of a similar structure is the liquid crystal panel, which has already been commercialized successfully. The third reason lies in the fact that, at present, the liquid crystal is one of the few technologies capable of providing switching capabilities at frequencies above 60 GHz. In fact, the liquid crystal allows its permittivity to be switched in a wide range of frequencies, which are from DC to the visible spectrum, including microwaves and THz. Other technologies, such as ferroelectric materials, graphene or CMOS "on chip" technology also allow the beam to be switched at these frequencies. However, CMOS technology is expensive and is currently limited to frequencies below 150 GHz, and although ferroelectric materials or graphene can switch at higher frequencies and in a wider range, they have serious difficulties that make them immature. Ferroelectric materials involve the use of very high voltages to switch the material, making them unattractive, whereas the electromagnetic modelling of the graphene is still under discussion, so that the experimental results of devices based on this latter technology have not been reported yet. These three reasons make LC-based reflectarrays attractive for many applications that involve the use of electronically reconfigurable beams at frequencies beyond 60 GHz. Applications such as high resolution imaging radars, molecular spectroscopy, radiometers for atmospheric observation, or high frequency wireless communications (WiGig) are just some of them. This thesis is divided into three parts. In the first part, the most common properties of the liquid crystal materials are described, especially those exhibited in the nematic phase. The study is focused on the dielectric anisotropy (Ac) of uniaxial liquid crystals, which is defined as the difference between the parallel (e/7) and perpendicular (e±) permittivities: Ae = e,, - e±. This parameter allows the permittivity of a LC confined in an arbitrary volume at a certain biasing voltage to be described by solving a variational problem that involves both the electrostatic and elastic energies. Thus, the frequency dependence of (Ae) is also described and characterised. Note that an appropriate LC modelling is quite important to ensure enough accuracy in the phase shift provided by each cell that makes up the reflectarray, and therefore to achieve a good electrical performance at the antenna level. The second part of the thesis is focused on the design of resonant reflectarray cells based on liquid crystal. The reason why resonant cells have been chosen lies in the fact that they are able to provide enough phase range using the values of the dielectric anisotropy of the liquid crystals, which are typically small. Thus, the aim of this part is to investigate several reflectarray cell architectures capable of providing good electrical performance at the antenna level, which significantly improve the electrical performance of the cells reported in the literature. Similarly, another of the objectives is to develop a general tool to design these cells. To fulfill these objectives, the electrical yields of different types of resonant reflectarray elements are investigated, beginning from the simplest, which is made up of a single resonator and limits the state of the art. To overcome the electrical limitations of the single resonant cell, several elements consisting of multiple resonators are considered, which can be single-layer or multilayer. In a first step, the design procedure of these structures makes use of a conventional electromagnetic model which has been used in the literature, which considers that the liquid crystal behaves as homogeneous and isotropic materials whose permittivity varies between (e/7) y (e±). However, in this part of the thesis it is shown that the conventional modelling is not enough to describe the physical behaviour of the liquid crystal in reflectarray cells accurately. Therefore, a more accurate analysis and design procedure based on a more general model is proposed and developed, which defines the liquid crystal as an anisotropic three-dimensional inhomogeneous material. The design procedure is able to optimize multi-resonant cells efficiently to achieve good electrical performance in terms of bandwidth, phase range, losses, or sensitivity to the angle of incidence. The errors made when the conventional modelling (amplitude and phase) is considered have been also analysed for various cell geometries, by using measured results from several antenna prototypes made up of real liquid crystals at frequencies above 100 GHz. The measurements have been performed in a periodic environment using a quasi-optical bench, which has been designed especially for this purpose. One of these prototypes has been optimized to achieve a relatively large bandwidth (10%) at 100 GHz, low losses, a phase range of more than 360º, a low sensitivity to angle of incidence, and a low influence of the transversal inhomogeneity of the liquid crystal in the cell. The electrical yields of this prototype at the cell level improve those achieved by other elements reported in the literature, so that this prototype has been used in the last part of the thesis to perform several complete antennas for beam scanning applications. Finally, in this second part of the thesis, a novel strategy to characterise the macroscopic anisotropy using reflectarray cells is presented. The results in both RF and AC frequencies are compared with those obtained by other methods. The third part of the thesis consists on the study, design, manufacture and testing of LCbased reflectarray antennas in complex configurations. Note that the design procedure of a passive reflectarray antenna just consists on finding out the dimensions of the metallisations of each cell (which are used for phase control), using well-known optimization processes. However, in the case of reconfigurable reflectarrays based on liquid crystals, an additional step must be taken into account, which consists of accurately calculating the control voltages to be applied to each cell to configure the required phase-shift distribution on the surface of the antenna. Similarly, the structure to address the voltages at each cell and the control circuitry must be also considered. Therefore, the voltage synthesis is even more important than the design of the cell geometries (dimensions), since the voltages are directly related to the phase-shift. Several voltage synthesis procedures have been proposed in the state of the art, which are based on the experimental characterization of the phase/voltage curve. However, this characterization can be only carried out at a single angle of incidence and at certain cell dimensions, so that the synthesized voltages are different from those needed, thus giving rise to phase errors of more than 70°. Thus, the electrical yields of the LCreflectarrays reported in the literature are limited in terms of bandwidth, scanning range or side lobes level. In this last part of the thesis, a new voltage synthesis procedure has been defined and developed, which allows the required voltage to be calculated at each cell using simulations that take into account the particular dimensions of the cells, their angles of incidence, the frequency, and the AC biasing signal (frequency and waveform). The strategy is based on the modelling of each one of the permittivity states of the liquid crystal as an anisotropic substrate with longitudinal inhomogeneity (1D), or in certain cases, as an equivalent homogeneous tensor. The accuracy of both electromagnetic models is also discussed. The phase errors made by using the proposed voltage synthesis are better than 7º. In order to obtain an efficient tool to analyse and design the reflectarray, an electromagnetic analysis tool based on the Method of Moments in the spectral domain (SD-MoM) has also written and developed for anisotropic stratified media, which is used at each iteration of the voltage synthesis procedure. The voltage synthesis is also designed to minimize the effect of amplitude ripple on the radiation pattern, which is typical of reflectarrays made up of cells exhibiting high losses and represents a further advance in achieving a better antenna performance. To calculate the radiation patterns used in the synthesis procedure, an element-by-element analysis is assumed, which considers the local periodicity approach. Under this consideration, the use of a novel method is proposed, which avoids the limitation that the local periodicity imposes on the excitation. Once the appropriate strategy to calculate the voltages to be applied at each cell is developed, and once it is designed and manufactured both the structure to address the voltages to the antenna and the control circuits, two complete LC-based reflectarray antennas that operate at 100 GHz have been designed, manufactured and tested using the previously presented cells. The first prototype consists of a single offset reflectarray with beam scanning capabilities on one plane (elevation and azimuth). Although several LC-reflectarray antennas that provide 2-D scanning capabilities are also designed, and certain strategies to achieve the 2-D addressing of the voltage are proposed, the manufactured prototype addresses the voltages in one dimension in order to reduce the number of controls and manufacturing errors, and thereby validating the design tool. For an average aperture size (with a number of rows and columns of between 30 and 50 elements, which means a reflectarray with more than 900 cells), the single offset configuration provides an antenna gain of between 20 and 30 dBi and a large scanning range. The prototype tested at 100 GHz exhibits an electronically scanned beam in an angular range of 55º and 8% of bandwidth, in which the side lobe level (SLL) remains better than -13 dB. The maximum gain is 19.4 dBi. The electrical performance of the antenna is clearly an improvement on those achieved by other authors in the state of the art. The second prototype corresponds to a dual reflector antenna with a liquid crystal-based reflectarray used as a sub-reflector for beam scanning in one plane (azimuth or elevation). The main objective is to obtain a higher gain than that provided by the single offset configuration, but using a more compact architecture. In this case, a maximum gain of 35 dBi is achieved, although at the expense of reducing the scanning range to 12°, which is inherent in this type of structure. As a general statement, the voltage synthesis and the design procedure of the cells, jointly make up a complete, accurate and efficient design tool of reconfigurable reflectarray antennas based on liquid crystals. The tool has been validated by testing the previously mentioned prototypes at 100 GHz, which achieve something never reached before for this type of antenna: a competitive electrical performance, and an excellent prediction of the results. The design procedure is general and therefore can be used at any frequency for which the liquid crystal exhibits dielectric anisotropy. The two prototypes designed, manufactured and tested in this thesis are also some of the first antennas that currently operate at frequencies above 100 GHz. In fact, the dual reflector antenna is the first electronically scanned dual reflector antenna at frequencies above 60 GHz (the operation frequency is 100 GHz) with a gain greater than 25 dBi, being in turn the first dual-reflector antenna with a real reconfigurable sub-reflectarray. Finally, some improvements that should be still investigated to make these antennas commercially competitive are proposed.

Effect of type of fiber, site of fermentation, and method of analysis on digestibility of soluble and insoluble fiber in rabbits

The effect of type of fiber, site of fermetation, method for quantifying insoluble and soluble dietary fiber, and their correction for intestinal mucin on fiber digestibility were examined in rabbits. Three diets differing in soluble fiber were formulated (8.5% soluble fiber, on DM basis, in the low soluble fiber [LSF] diet; 10.2% in the medium soluble fiber [MSF] diet; and 14.5% in the high soluble fiber [HSF] diet). They were obtained by replacing half of the dehydrated alfalfa in the MSF diet with a mixture of beet and apple pulp (HSF diet) or with a mix of oat hulls and soybean protein (LSF diet). Thirty rabbits with ileal T-cannulas were used to determine ileal and fecal digestibility. Cecal digestibility was determined by difference between fecal and ileal digestibility. Insoluble fiber was measured as NDF, insoluble dietary fiber (IDF), and in vitro insoluble fiber, whereas soluble fiber was calculated as the difference between total dietary fiber (TDF) and NDF (TDF_NDF), IDF (TDF-IDF), and in vitro insoluble fiber (TDF-in vitro insoluble fiber). The intestinal mucin content was used to correct the TDF and soluble fiber digestibility. Ileal and fecal concentration of mucin increased from the LSF to the HSF diet group (P < 0.01). Once corrected for intestinal mucin, ileal and fecal digestibility of TDF and soluble fiber increased whereas cecal digestibility decreased (P < 0.01). Ileal digestibility of TDF increased from the LSF to the HSF diet group (12.0 vs. 28.1%; P < 0.01), with no difference in the cecum (26.4%), resulting in a higher fecal digestibility from the LSF to the HSF diet group (P < 0.01). Ileal digestibility of insoluble fiber increased from the LSF to the HSF diet group (11.3 vs. 21.0%; P < 0.01), with no difference in the cecum (13.9%) and no effect of fiber method, resulting in a higher fecal digestibility for rabbits fed the HSF diet compared with the MSF and LSF diets groups (P < 0.01).Fecal digestibility of NDF was higher compared with IDF or in vitro insoluble fiber (P < 0.01). Ileal soluble fiber digestibility was higher for the HSF than for the LSF diet group (43.6 vs. 14.5%; P < 0.01) and fiber method did not affect it. Cecal soluble fiber digestibility decreased from the LSF to the HSF diet group (72.1 vs. 49.2%; P < 0.05). The lowest cecal and fecal soluble fiber digestibility was measured using TDF-NDF (P < 0.01). In conclusion, a correction for intestinal mucin is necessary for ileal TDF and soluble fiber digestibility whereas the selection of the fiber method has a minor relevance. The inclusion of sugar beet and apple pulp increased the amount of TDF fermented in the small intestine.

Adaptation Strategies for Discontinuous Galerkin Spectral Element Methods by means of Truncation Error Estimations

In this work a p-adaptation (modification of the polynomial order) strategy based on the minimization of the truncation error is developed for high order discontinuous Galerkin methods. The truncation error is approximated by means of a truncation error estimation procedure and enables the identification of mesh regions that require adaptation. Three truncation error estimation approaches are developed and termed a posteriori, quasi-a priori and quasi-a priori corrected. Fine solutions, which are obtained by enriching the polynomial order, are required to solve the numerical problem with adequate accuracy. For the three truncation error estimation methods the former needs time converged solutions, while the last two rely on non-converged solutions, which lead to faster computations. Based on these truncation error estimation methods, algorithms for mesh adaptation were designed and tested. Firstly, an isotropic adaptation approach is presented, which leads to equally distributed polynomial orders in different coordinate directions. This first implementation is improved by incorporating a method to extrapolate the truncation error. This results in a significant reduction of computational cost. Secondly, the employed high order method permits the spatial decoupling of the estimated errors and enables anisotropic p-adaptation. The incorporation of anisotropic features leads to meshes with different polynomial orders in the different coordinate directions such that flow-features related to the geometry are resolved in a better manner. These adaptations result in a significant reduction of degrees of freedom and computational cost, while the amount of improvement depends on the test-case. Finally, this anisotropic approach is extended by using error extrapolation which leads to an even higher reduction in computational cost. These strategies are verified and compared in terms of accuracy and computational cost for the Euler and the compressible Navier-Stokes equations. The main result is that the two quasi-a priori methods achieve a significant reduction in computational cost when compared to a uniform polynomial enrichment. Namely, for a viscous boundary layer flow, we obtain a speedup of a factor of 6.6 and 7.6 for the quasi-a priori and quasi-a priori corrected approaches, respectively. RESUMEN En este trabajo se ha desarrollado una estrategia de adaptación-p (modificación del orden polinómico) para métodos Galerkin discontinuo de alto orden basada en la minimización del error de truncación. El error de truncación se estima utilizando el método tau-estimation. El estimador permite la identificación de zonas de la malla que requieren adaptación. Se distinguen tres técnicas de estimación: a posteriori, quasi a priori y quasi a priori con correción. Todas las estrategias requieren una solución obtenida en una malla fina, la cual es obtenida aumentando de manera uniforme el orden polinómico. Sin embargo, mientras que el primero requiere que esta solución esté convergida temporalmente, el resto utiliza soluciones no convergidas, lo que se traduce en un menor coste computacional. En este trabajo se han diseñado y probado algoritmos de adaptación de malla basados en métodos tau-estimation. En primer lugar, se presenta un algoritmo de adaptacin isótropo, que conduce a discretizaciones con el mismo orden polinómico en todas las direcciones espaciales. Esta primera implementación se mejora incluyendo un método para extrapolar el error de truncación. Esto resulta en una reducción significativa del coste computacional. En segundo lugar, el método de alto orden permite el desacoplamiento espacial de los errores estimados, permitiendo la adaptación anisotropica. Las mallas obtenidas mediante esta técnica tienen distintos órdenes polinómicos en cada una de las direcciones espaciales. La malla final tiene una distribución óptima de órdenes polinómicos, los cuales guardan relación con las características del flujo que, a su vez, depenen de la geometría. Estas técnicas de adaptación reducen de manera significativa los grados de libertad y el coste computacional. Por último, esta aproximación anisotropica se extiende usando extrapolación del error de truncación, lo que conlleva un coste computational aún menor. Las estrategias se verifican y se comparan en téminors de precisión y coste computacional utilizando las ecuaciones de Euler y Navier Stokes. Los dos métodos quasi a priori consiguen una reducción significativa del coste computacional en comparación con aumento uniforme del orden polinómico. En concreto, para una capa límite viscosa, obtenemos una mejora en tiempo de computación de 6.6 y 7.6 respectivamente, para las aproximaciones quasi-a priori y quasi-a priori con corrección.