Multiphase Buck Converter with Minimum Time Control Strategy for RF Envelope Modulation

Power amplifier supplied with constant supply voltage has very low efficiency in the transmitter. A DC-DC converter in series with a linear regulator can be used to obtain voltage modulation. Since this converter should be able to change the output voltage very fast, a multiphase buck converter with a minimum time control strategy is proposed. To modulate supply voltage of the envelope amplifier, the multiphase converter works with some particular duty cycle (i/n, i=1, 2 ... n, n is the number of phase) to generate discrete output voltages, and in these duty cycles the output current ripple can be completely cancelled. The transition times for the minimum time are pre-calculated and inserted in a look-up table. The theoretical background, the system model that is necessary in order to calculate the transition times and the experimental results obtained with a 4-phase buck prototype are given

Single-Stage Grid-Connected Forward Microinverter with Boundary Mode Control

This paper presents a microinverter to be integrated into a solar module. The proposed solution combines a forward converter and a constant off-time boundary mode control, providing MPPT capability and unity power factor in a single-stage converter. The transformer structure of the power stage remains as in the classical DC-DC forward converter. Transformer primary windings are utilized for power transfer or demagnetization depending on the grid semi-cycle. Furthermore, bidirectional switches are used on the secondary side allowing direct connection of the inverter to the grid. Design considerations for the proposed solution are provided, regarding the inductance value, transformer turns ratio and frequency variation during a line semi-cycle. The decoupling of the twice the line frequency power pulsation is also discussed, as well as the maximum power point tracking (MPPT) capability. Simulation and experimental results for a 100W prototype are enclosed

Structural properties of InAlN single layers nearly latice-matched to GaN grown by plasma assisted molecular beal epitaxy

The high lattice mismatch between III-nitride binaries (InN, GaN and AlN) remains a key problem to grow high quality III-nitride heterostructures. Recent interest has been focused on the growth of high-quality InAlN layers, with approximately 18% of indium incorporation, in-plane lattice-matched (LM) to GaN. While a lot of work has been done by metal-organic vapour phase epitaxy (MOVPE) by Carlin and co-workers, its growth by molecular beam epitaxy (MBE) is still in infancy

Modulation instability-induced fading in phase-sensitive optical time-domain reflectometry

Phase-sensitive optical time-domain reflectometry (?OTDR) is a simple and effective tool allowing the distributed monitoring of vibrations along single-mode fibers. We show in this Letter that modulation instability (MI) can induce a position-dependent signal fading in long-range ?OTDR over conventional optical fibers. This fading leads to a complete masking of the interference signal recorded at certain positions and therefore to a sensitivity loss at these positions. We illustrate this effect both theoretically and experimentally. While this effect is detrimental in the context of distributed vibration analysis using ?OTDR, we also believe that the technique provides a clear and insightful way to evidence the Fermi?Pasta?Ulam recurrence associated with the MI process.

Single - and double energy swift and slow heavy ion irradiated optical waveguides in Er: Tungstene-Tellurite glass and BGO for telecom applications

The fabrication of broadband amplifiers in wavelength division multiplexing (WDM) around 1.55 m, as they exhibit large stimulated cross sections and broad emission bandwidth. Bi4Ge3O12 (eultine type BGO) - well known scintillator material, also a rare-earth host material, photorefractive waveguides produced in it only using light ions in the past. Recently: MeV N+ ions and swift O5+ and C5+ ions, too*. Bi12GeO20 (sillenite type BGO) - high photoconductivity and photorefractive sensitivity in the visible and NIR good candidate for real-time holography and optical phase conjugation, photorefractive waveguides produced in it only using light ions. No previous attempts of ion beam fabrication of waveguides in it.

Analysis and optimized design of a distributed multi-stage EMC filter for an interleaved three-phase PWM-rectifier system for aircraft applications

Different possible input filter configurations for a modular three-phase PWM rectifier system consisting of three interleaved converter cells are studied. The system is designed for an aircraft application where MIL-STD-461E conducted EMI standards have to be met and system weight is a critical design issue. The importance of a LISN model on the simulated noise levels and the effect of interleaving and power unbalance between the different converter modules is discussed. The effect of the number of filter stages and the degree of distribution of the filter stages among the individual converter modules on the weight and losses of the input filter is studied and optimal filter structures are proposed.

Multiple Input-Output Bidirectional Solid State Transformer Based on a Series Resonant Converter

Las fuentes de alimentación de modo conmutado (SMPS en sus siglas en inglés) se utilizan ampliamente en una gran variedad de aplicaciones. La tarea más difícil para los diseñadores de SMPS consiste en lograr simultáneamente la operación del convertidor con alto rendimiento y alta densidad de energía. El tamaño y el peso de un convertidor de potencia está dominado por los componentes pasivos, ya que estos elementos son normalmente más grandes y más pesados que otros elementos en el circuito. Para una potencia de salida dada, la cantidad de energía almacenada en el convertidor que ha de ser entregada a la carga en cada ciclo de conmutación, es inversamente proporcional a la frecuencia de conmutación del convertidor. Por lo tanto, el aumento de la frecuencia de conmutación se considera un medio para lograr soluciones más compactas con los niveles de densidad de potencia más altos. La importancia de investigar en el rango de alta frecuencia de conmutación radica en todos los beneficios que se pueden lograr: además de la reducción en el tamaño de los componentes pasivos, el aumento de la frecuencia de conmutación puede mejorar significativamente prestaciones dinámicas de convertidores de potencia. Almacenamiento de energía pequeña y el período de conmutación corto conducen a una respuesta transitoria del convertidor más rápida en presencia de las variaciones de la tensión de entrada o de la carga. Las limitaciones más importantes del incremento de la frecuencia de conmutación se relacionan con mayores pérdidas del núcleo magnético convencional, así como las pérdidas de los devanados debido a los efectos pelicular y proximidad. También, un problema potencial es el aumento de los efectos de los elementos parásitos de los componentes magnéticos - inductancia de dispersión y la capacidad entre los devanados - que causan pérdidas adicionales debido a las corrientes no deseadas. Otro factor limitante supone el incremento de las pérdidas de conmutación y el aumento de la influencia de los elementos parásitos (pistas de circuitos impresos, interconexiones y empaquetado) en el comportamiento del circuito. El uso de topologías resonantes puede abordar estos problemas mediante el uso de las técnicas de conmutaciones suaves para reducir las pérdidas de conmutación incorporando los parásitos en los elementos del circuito. Sin embargo, las mejoras de rendimiento se reducen significativamente debido a las corrientes circulantes cuando el convertidor opera fuera de las condiciones de funcionamiento nominales. A medida que la tensión de entrada o la carga cambian las corrientes circulantes incrementan en comparación con aquellos en condiciones de funcionamiento nominales. Se pueden obtener muchos beneficios potenciales de la operación de convertidores resonantes a más alta frecuencia si se emplean en aplicaciones con condiciones de tensión de entrada favorables como las que se encuentran en las arquitecturas de potencia distribuidas. La regulación de la carga y en particular la regulación de la tensión de entrada reducen tanto la densidad de potencia del convertidor como el rendimiento. Debido a la relativamente constante tensión de bus que se encuentra en arquitecturas de potencia distribuidas los convertidores resonantes son adecuados para el uso en convertidores de tipo bus (transformadores cc/cc de estado sólido). En el mercado ya están disponibles productos comerciales de transformadores cc/cc de dos puertos que tienen muy alta densidad de potencia y alto rendimiento se basan en convertidor resonante serie que opera justo en la frecuencia de resonancia y en el orden de los megahercios. Sin embargo, las mejoras futuras en el rendimiento de las arquitecturas de potencia se esperan que vengan del uso de dos o más buses de distribución de baja tensión en vez de una sola. Teniendo eso en cuenta, el objetivo principal de esta tesis es aplicar el concepto del convertidor resonante serie que funciona en su punto óptimo en un nuevo transformador cc/cc bidireccional de puertos múltiples para atender las necesidades futuras de las arquitecturas de potencia. El nuevo transformador cc/cc bidireccional de puertos múltiples se basa en la topología de convertidor resonante serie y reduce a sólo uno el número de componentes magnéticos. Conmutaciones suaves de los interruptores hacen que sea posible la operación en las altas frecuencias de conmutación para alcanzar altas densidades de potencia. Los problemas posibles con respecto a inductancias parásitas se eliminan, ya que se absorben en los Resumen elementos del circuito. El convertidor se caracteriza con una muy buena regulación de la carga propia y cruzada debido a sus pequeñas impedancias de salida intrínsecas. El transformador cc/cc de puertos múltiples opera a una frecuencia de conmutación fija y sin regulación de la tensión de entrada. En esta tesis se analiza de forma teórica y en profundidad el funcionamiento y el diseño de la topología y del transformador, modelándolos en detalle para poder optimizar su diseño. Los resultados experimentales obtenidos se corresponden con gran exactitud a aquellos proporcionados por los modelos. El efecto de los elementos parásitos son críticos y afectan a diferentes aspectos del convertidor, regulación de la tensión de salida, pérdidas de conducción, regulación cruzada, etc. También se obtienen los criterios de diseño para seleccionar los valores de los condensadores de resonancia para lograr diferentes objetivos de diseño, tales como pérdidas de conducción mínimas, la eliminación de la regulación cruzada o conmutación en apagado con corriente cero en plena carga de todos los puentes secundarios. Las conmutaciones en encendido con tensión cero en todos los interruptores se consiguen ajustando el entrehierro para obtener una inductancia magnetizante finita en el transformador. Se propone, además, un cambio en los señales de disparo para conseguir que la operación con conmutaciones en apagado con corriente cero de todos los puentes secundarios sea independiente de la variación de la carga y de las tolerancias de los condensadores resonantes. La viabilidad de la topología propuesta se verifica a través una extensa tarea de simulación y el trabajo experimental. La optimización del diseño del transformador de alta frecuencia también se aborda en este trabajo, ya que es el componente más voluminoso en el convertidor. El impacto de de la duración del tiempo muerto y el tamaño del entrehierro en el rendimiento del convertidor se analizan en un ejemplo de diseño de transformador cc/cc de tres puertos y cientos de vatios de potencia. En la parte final de esta investigación se considera la implementación y el análisis de las prestaciones de un transformador cc/cc de cuatro puertos para una aplicación de muy baja tensión y de decenas de vatios de potencia, y sin requisitos de aislamiento. Abstract Recently, switch mode power supplies (SMPS) have been used in a great variety of applications. The most challenging issue for designers of SMPS is to achieve simultaneously high efficiency operation at high power density. The size and weight of a power converter is dominated by the passive components since these elements are normally larger and heavier than other elements in the circuit. If the output power is constant, the stored amount of energy in the converter which is to be delivered to the load in each switching cycle is inversely proportional to the converter’s switching frequency. Therefore, increasing the switching frequency is considered a mean to achieve more compact solutions at higher power density levels. The importance of investigation in high switching frequency range comes from all the benefits that can be achieved. Besides the reduction in size of passive components, increasing switching frequency can significantly improve dynamic performances of power converters. Small energy storage and short switching period lead to faster transient response of the converter against the input voltage and load variations. The most important limitations for pushing up the switching frequency are related to increased conventional magnetic core loss as well as the winding loss due to the skin and proximity effect. A potential problem is also increased magnetic parasitics – leakage inductance and capacitance between the windings – that cause additional loss due to unwanted currents. Higher switching loss and the increased influence of printed circuit boards, interconnections and packaging on circuit behavior is another limiting factor. Resonant power conversion can address these problems by using soft switching techniques to reduce switching loss incorporating the parasitics into the circuit elements. However the performance gains are significantly reduced due to the circulating currents when the converter operates out of the nominal operating conditions. As the input voltage or the load change the circulating currents become higher comparing to those ones at nominal operating conditions. Multiple Input-Output Many potential gains from operating resonant converters at higher switching frequency can be obtained if they are employed in applications with favorable input voltage conditions such as those found in distributed power architectures. Load and particularly input voltage regulation reduce a converter’s power density and efficiency. Due to a relatively constant bus voltage in distributed power architectures the resonant converters are suitable for bus voltage conversion (dc/dc or solid state transformation). Unregulated two port dc/dc transformer products achieving very high power density and efficiency figures are based on series resonant converter operating just at the resonant frequency and operating in the megahertz range are already available in the market. However, further efficiency improvements of power architectures are expected to come from using two or more separate low voltage distribution buses instead of a single one. The principal objective of this dissertation is to implement the concept of the series resonant converter operating at its optimum point into a novel bidirectional multiple port dc/dc transformer to address the future needs of power architectures. The new multiple port dc/dc transformer is based on a series resonant converter topology and reduces to only one the number of magnetic components. Soft switching commutations make possible high switching frequencies to be adopted and high power densities to be achieved. Possible problems regarding stray inductances are eliminated since they are absorbed into the circuit elements. The converter features very good inherent load and cross regulation due to the small output impedances. The proposed multiple port dc/dc transformer operates at fixed switching frequency without line regulation. Extensive theoretical analysis of the topology and modeling in details are provided in order to compare with the experimental results. The relationships that show how the output voltage regulation and conduction losses are affected by the circuit parasitics are derived. The methods to select the resonant capacitor values to achieve different design goals such as minimum conduction losses, elimination of cross regulation or ZCS operation at full load of all the secondary side bridges are discussed. ZVS turn-on of all the switches is achieved by relying on the finite magnetizing inductance of the Abstract transformer. A change of the driving pattern is proposed to achieve ZCS operation of all the secondary side bridges independent on load variations or resonant capacitor tolerances. The feasibility of the proposed topology is verified through extensive simulation and experimental work. The optimization of the high frequency transformer design is also addressed in this work since it is the most bulky component in the converter. The impact of dead time interval and the gap size on the overall converter efficiency is analyzed on the design example of the three port dc/dc transformer of several hundreds of watts of the output power for high voltage applications. The final part of this research considers the implementation and performance analysis of the four port dc/dc transformer in a low voltage application of tens of watts of the output power and without isolation requirements.

Interleaved multi-cell isolated three-phase PWM rectifier system for aircraft applications

Recently there has been an important increase in electric equipment, as well as, electric power demand in aircrafts applications. This prompts to the necessity of efficient, reliable, and low-weight converters, especially rectifiers from 115VAC to 270VDC because these voltages are used in power distribution. In order to obtain a high efficiency, in aircraft application where the derating in semiconductors is high, normally several semiconductors are used in parallel to decrease the conduction losses. However, this is in conflict with high reliability. To match both goals of high efficiency and reliability, this work proposes an interleaved multi-cell rectifier system, employing several converter cells in parallel instead of parallel-connected semiconductors. In this work a 10kW multi-cell isolated rectifier system has been designed where each cell is composed of a buck type rectifier and a full bridge DC-DC converter. The implemented system exhibits 91% of efficiency, high power density (10kW/10kg), low THD (2.5%), and n−1 fault tolerance which complies, with military aircraft standards.

Ripple cancellation technique applied to a synchronous buck converter to achieve very high bandwidth and very high efficiency envelope amplifier

This work presents a single stage converter for a high bandwidth and a high efficiency envelope amplifier. The current ripple cancellation technique is applied to a synchronous buck converter to cancel the output current ripple and to decrease the switching frequency without a reduction in the large signal bandwidth. The converter is modeled and the new design with ripple cancellation circuit is detailed. The advantages of the proposed design are presented and validated experimentally. The transfer function of the output filter of the buck converter with ripple cancellation circuit has been modeled and compared to measurements, showing a good correspondence. Experimental validation is provided at 4MHz of switching frequency for DC and variable output voltage for a sinusoidal and a 64QAM signal. Additional experimental validation of the efficiency improvement is provided, compared to the equivalent design (same bandwidth and output voltage ripple) of the conventional buck converter.

Novel dual-band single circular polarization antenna feeding network for satellite communications

In this paper a novel dual-band single circular polarization antenna feeding network for satellite communications is presented. The novel antenna feed chain1 is composed of two elements or subsystems, namely a diplexer and a bi-phase polarizer. In comparison with the classic topology based on an orthomode transducer and a dual-band polarizer, the proposed feed chain presents several advantages, such as compactness, modular design of the different components, broadband operation and versatility in the subsystems interconnection. The design procedure of this new antenna feed configuration is explained. Different examples of antenna feeding networks at 20/30 GHz are presented. It is pointed out the excellent results obtained in terms of isolation and axial ratio.

Power Converter Topologies for a High Performance Transformer Rectifier Unit in Aircraft Applications

This paper presents some power converter architectures and circuit topologies, which can be used to achieve the requirements of the high performance transformer rectifier unit in aircraft applications, mainly as: high power factor with low THD, high efficiency and high power density. The voltage and the power levels demanded for this application are: three-phase line-to-neutral input voltage of 115 or 230V AC rms (360 – 800Hz), output voltage of 28V DC or 270V DC(new grid value) and the output power up to tens of kilowatts.

Contribución a la caracterización espacial de canales con sistemas MIMO-OFDM en la banda de 2,45 Ghz

La tecnología de múltiples antenas ha evolucionado para dar soporte a los actuales y futuros sistemas de comunicaciones inalámbricas en su afán por proporcionar la calidad de señal y las altas tasas de transmisión que demandan los nuevos servicios de voz, datos y multimedia. Sin embargo, es fundamental comprender las características espaciales del canal radio, ya que son las características del propio canal lo que limita en gran medida las prestaciones de los sistemas de comunicación actuales. Por ello surge la necesidad de estudiar la estructura espacial del canal de propagación para poder diseñar, evaluar e implementar de forma más eficiente tecnologías multiantena en los actuales y futuros sistemas de comunicación inalámbrica. Las tecnologías multiantena denominadas antenas inteligentes y MIMO han generado un gran interés en el área de comunicaciones inalámbricas, por ejemplo los sistemas de telefonía celular o más recientemente en las redes WLAN (Wireless Local Area Network), principalmente por la mejora que proporcionan en la calidad de las señales y en la tasa de transmisión de datos, respectivamente. Las ventajas de estas tecnologías se fundamentan en el uso de la dimensión espacial para obtener ganancia por diversidad espacial, como ya sucediera con las tecnologías FDMA (Frequency Division Multiplexing Access), TDMA (Time Division Multiplexing Access) y CDMA (Code Division Multiplexing Access) para obtener diversidad en las dimensiones de frecuencia, tiempo y código, respectivamente. Esta Tesis se centra en estudiar las características espaciales del canal con sistemas de múltiples antenas mediante la estimación de los perfiles de ángulos de llegada (DoA, Direction-of- Arrival) considerando esquemas de diversidad en espacio, polarización y frecuencia. Como primer paso se realiza una revisión de los sistemas con antenas inteligentes y los sistemas MIMO, describiendo con detalle la base matemática que sustenta las prestaciones ofrecidas por estos sistemas. Posteriormente se aportan distintos estudios sobre la estimación de los perfiles de DoA de canales radio con sistemas multiantena evaluando distintos aspectos de antenas, algoritmos de estimación, esquemas de polarización, campo lejano y campo cercano de las fuentes. Así mismo, se presenta un prototipo de medida MIMO-OFDM-SPAA3D en la banda ISM (Industrial, Scientific and Medical) de 2,45 Ghz, el cual está preparado para caracterizar experimentalmente el rendimiento de los sistemas MIMO, y para caracterizar espacialmente canales de propagación, considerando los esquemas de diversidad espacial, por polarización y frecuencia. Los estudios aportados se describen a continuación. Los sistemas de antenas inteligentes dependen en gran medida de la posición de los usuarios. Estos sistemas están equipados con arrays de antenas, los cuales aportan la diversidad espacial necesaria para obtener una representación espacial fidedigna del canal radio a través de los perfiles de DoA (DoA, Direction-of-Arrival) y por tanto, la posición de las fuentes de señal. Sin embargo, los errores de fabricación de arrays así como ciertos parámetros de señal conlleva un efecto negativo en las prestaciones de estos sistemas. Por ello se plantea un modelo de señal parametrizado que permite estudiar la influencia que tienen estos factores sobre los errores de estimación de DoA, tanto en acimut como en elevación, utilizando los algoritmos de estimación de DOA más conocidos en la literatura. A partir de las curvas de error, se pueden obtener parámetros de diseño para sistemas de localización basados en arrays. En un segundo estudio se evalúan esquemas de diversidad por polarización con los sistemas multiantena para mejorar la estimación de los perfiles de DoA en canales que presentan pérdidas por despolarización. Para ello se desarrolla un modelo de señal en array con sensibilidad de polarización que toma en cuenta el campo electromagnético de ondas planas. Se realizan simulaciones MC del modelo para estudiar el efecto de la orientación de la polarización como el número de polarizaciones usadas en el transmisor como en el receptor sobre la precisión en la estimación de los perfiles de DoA observados en el receptor. Además, se presentan los perfiles DoA obtenidos en escenarios quasiestáticos de interior con un prototipo de medida MIMO 4x4 de banda estrecha en la banda de 2,45 GHz, los cuales muestran gran fidelidad con el escenario real. Para la obtención de los perfiles DoA se propone un método basado en arrays virtuales, validado con los datos de simulación y los datos experimentales. Con relación a la localización 3D de fuentes en campo cercano (zona de Fresnel), se presenta un tercer estudio para obtener con gran exactitud la estructura espacial del canal de propagación en entornos de interior controlados (en cámara anecóica) utilizando arrays virtuales. El estudio analiza la influencia del tamaño del array y el diagrama de radiación en la estimación de los parámetros de localización proponiendo, para ello, un modelo de señal basado en un vector de enfoque de onda esférico (SWSV). Al aumentar el número de antenas del array se consigue reducir el error RMS de estimación y mejorar sustancialmente la representación espacial del canal. La estimación de los parámetros de localización se lleva a cabo con un nuevo método de búsqueda multinivel adaptativo, propuesto con el fin de reducir drásticamente el tiempo de procesado que demandan otros algoritmos multivariable basados en subespacios, como el MUSIC, a costa de incrementar los requisitos de memoria. Las simulaciones del modelo arrojan resultados que son validados con resultados experimentales y comparados con el límite de Cramer Rao en términos del error cuadrático medio. La compensación del diagrama de radiación acerca sustancialmente la exactitud de estimación de la distancia al límite de Cramer Rao. Finalmente, es igual de importante la evaluación teórica como experimental de las prestaciones de los sistemas MIMO-OFDM. Por ello, se presenta el diseño e implementación de un prototipo de medida MIMO-OFDM-SPAA3D autocalibrado con sistema de posicionamiento de antena automático en la banda de 2,45 Ghz con capacidad para evaluar la capacidad de los sistemas MIMO. Además, tiene la capacidad de caracterizar espacialmente canales MIMO, incorporando para ello una etapa de autocalibración para medir la respuesta en frecuencia de los transmisores y receptores de RF, y así poder caracterizar la respuesta de fase del canal con mayor precisión. Este sistema incorpora un posicionador de antena automático 3D (SPAA3D) basado en un scanner con 3 brazos mecánicos sobre los que se desplaza un posicionador de antena de forma independiente, controlado desde un PC. Este posicionador permite obtener una gran cantidad de mediciones del canal en regiones locales, lo cual favorece la caracterización estadística de los parámetros del sistema MIMO. Con este prototipo se realizan varias campañas de medida para evaluar el canal MIMO en términos de capacidad comparando 2 esquemas de polarización y tomando en cuenta la diversidad en frecuencia aportada por la modulación OFDM en distintos escenarios. ABSTRACT Multiple-antennas technologies have been evolved to be the support of the actual and future wireless communication systems in its way to provide the high quality and high data rates required by new data, voice and data services. However, it is important to understand the behavior of the spatial characteristics of the radio channel, since the channel by itself limits the performance of the actual wireless communications systems. This drawback raises the need to understand the spatial structure of the propagation channel in order to design, assess, and develop more efficient multiantenna technologies for the actual and future wireless communications systems. Multiantenna technologies such as ‘Smart Antennas’ and MIMO systems have generated great interest in the field of wireless communications, i.e. cellular communications systems and more recently WLAN (Wireless Local Area Networks), mainly because the higher quality and the high data rate they are able to provide. Their technological benefits are based on the exploitation of the spatial diversity provided by the use of multiple antennas as happened in the past with some multiaccess technologies such as FDMA (Frequency Division Multiplexing Access), TDMA (Time Division Multiplexing Access), and CDMA (Code Division Multiplexing Access), which give diversity in the domains of frequency, time and code, respectively. This Thesis is mainly focus to study the spatial channel characteristics using schemes of multiple antennas considering several diversity schemes such as space, polarization, and frequency. The spatial characteristics will be study in terms of the direction-of-arrival profiles viewed at the receiver side of the radio link. The first step is to do a review of the smart antennas and MIMO systems technologies highlighting their advantages and drawbacks from a mathematical point of view. In the second step, a set of studies concerning the spatial characterization of the radio channel through the DoA profiles are addressed. The performance of several DoA estimation methods is assessed considering several aspects regarding antenna array structure, polarization diversity, and far-field and near-field conditions. Most of the results of these studies come from simulations of data models and measurements with real multiantena prototypes. In the same way, having understand the importance of validate the theoretical data models with experimental results, a 2,4 GHz MIMO-OFDM-SPAA2D prototype is presented. This prototype is intended for evaluating MIMO-OFDM capacity in indoor and outdoor scenarios, characterize the spatial structure of radio channels, assess several diversity schemes such as polarization, space, and frequency diversity, among others aspects. The studies reported are briefly described below. As is stated in Chapter two, the determination of user position is a fundamental task to be resolved for the smart antenna systems. As these systems are equipped with antenna arrays, they can provide the enough spatial diversity to accurately draw the spatial characterization of the radio channel through the DoA profiles, and therefore the source location. However, certain real implementation factors related to antenna errors, signals, and receivers will certainly reduce the performance of such direction finding systems. In that sense, a parameterized narrowband signal model is proposed to evaluate the influence of these factors in the location parameter estimation through extensive MC simulations. The results obtained from several DoA algorithms may be useful to extract some parameter design for directing finding systems based on arrays. The second study goes through the importance that polarization schemes can have for estimating far-field DoA profiles in radio channels, particularly for scenarios that may introduce polarization losses. For this purpose, a narrowband signal model with polarization sensibility is developed to conduct an analysis of several polarization schemes at transmitter (TX) and receiver (RX) through extensive MC simulations. In addition, spatial characterization of quasistatic indoor scenarios is also carried out using a 2.45 GHz MIMO prototype equipped with single and dual-polarized antennas. A good agreement between the measured DoA profiles with the propagation scenario is achieved. The theoretical and experimental evaluation of polarization schemes is performed using virtual arrays. In that case, a DoA estimation method is proposed based on adding an phase reference to properly track the DoA, which shows good results. In the third study, the special case of near-field source localization with virtual arrays is addressed. Most of DoA estimation algorithms are focused in far-field source localization where the radiated wavefronts are assume to be planar waves at the receive array. However, when source are located close to the array, the assumption of plane waves is no longer valid as the wavefronts exhibit a spherical behavior along the array. Thus, a faster and effective method of azimuth, elevation angles-of-arrival, and range estimation for near-field sources is proposed. The efficacy of the proposed method is evaluated with simulation and validated with measurements collected from a measurement campaign carried out in a controlled propagation environment, i.e. anechoic chamber. Moreover, the performance of the method is assessed in terms of the RMSE for several array sizes, several source positions, and taking into account the effect of radiation pattern. In general, better results are obtained with larger array and larger source distances. The effect of the antennas is included in the data model leading to more accurate results, particularly for range rather than for angle estimation. Moreover, a new multivariable searching method based on the MUSIC algorithm, called MUSA (multilevel MUSIC-based algorithm), is presented. This method is proposed to estimate the 3D location parameters in a faster way than other multivariable algorithms, such as MUSIC algorithm, at the cost of increasing the memory size. Finally, in the last chapter, a MIMO-OFDM-SPAA3D prototype is presented to experimentally evaluate different MIMO schemes regarding antennas, polarization, and frequency in different indoor and outdoor scenarios. The prototype has been developed on a Software-Defined Radio (SDR) platform. It allows taking measurements where future wireless systems will be developed. The novelty of this prototype is concerning the following 2 subsystems. The first one is the tridimensional (3D) antenna positioning system (SPAA3D) based on three linear scanners which is developed for making automatic testing possible reducing errors of the antenna array positioning. A set of software has been developed for research works such as MIMO channel characterization, MIMO capacity, OFDM synchronization, and so on. The second subsystem is the RF autocalibration module at the TX and RX. This subsystem allows to properly tracking the spatial structure of indoor and outdoor channels in terms of DoA profiles. Some results are draw regarding performance of MIMO-OFDM systems with different polarization schemes and different propagation environments.

Analysis of single and binary phases in cerium doped sodium bismuth titanate -Na0.5Bi0.5TiO3 materials

The pure and cerium doped sodium bismuth titanate inorganic powders were synthesized by solid state reaction method. The presence of rhombohedral phase was observed in cerium doped NBT compounds. At 1200 ºC, the 5% of cerium doped NBT compound forms single perovskite phase. The samples of x = 0.10 and 0.15 were heat treated to 1350 ºC, the binary phases with cerium and bismuth oxides were observed. The X-ray diffraction, fourier transform infrared spectroscopy, reflectance spectra, differential thermal analysis and thermo gravimetric analysis were used to analyze the various properties of samples. Moreover, the effects of cerium doping and calcining temperature on NBT samples were investigated. In this work we present our recent results on the synthesis and characterization of Ce doped sodium bismuth titanate materials.

Hybrid thermionic-photovoltaic converter

A conceptual device for the direct conversion of heat into electricity is presented. This concept hybridizes thermionic (TI) and thermophotovoltaic (TPV) energy conversion in a single thermionic-photovoltaic (TIPV) solid-state device. This device transforms into electricity both the electron and photon fluxes emitted by an incandescent surface. This letter presents an idealized analysis of this device in order to determine its theoretical potential. According to this analysis, the key advantage of this converter, with respect to either TPV or TI, is the higher power density in an extended temperature range. For low temperatures, TIPV performs like TPV due to the negligible electron flux. On the contrary, for high temperatures, TIPV performs like TI due to the great enhancement of the electron flux, which overshadows the photon flux contribution. At the intermediate temperatures, 1650K in the case of this particular study, I show that the power density potential of TIPV converter is twice as great as that of TPV and TI. The greatest impact concerns applications in which the temperature varies in a relatively wide range, for which averaged power density enhancement above 500% is attainable. (C) 2016 AIP Publishing LLC.

Ultra high temperature latent heat energy storage and thermophotovoltaic energy conversion

A conceptual energy storage system design that utilizes ultra high temperature phase change materials is presented. In this system, the energy is stored in the form of latent heat and converted to electricity upon demand by TPV (thermophotovoltaic) cells. Silicon is considered in this study as PCM (phase change material) due to its extremely high latent heat (1800 J/g or 500 Wh/kg), melting point (1410 C), thermal conductivity (~25 W/mK), low cost (less than $2/kg or $4/kWh) and abundance on earth. The proposed system enables an enormous thermal energy storage density of ~1 MWh/m3, which is 10e20 times higher than that of lead-acid batteries, 2e6 times than that of Li-ion batteries and 5e10 times than that of the current state of the art LHTES systems utilized in CSP (concentrated solar power) applications. The discharge efficiency of the system is ultimately determined by the TPV converter, which theoretically can exceed 50%. However, realistic discharge efficiencies utilizing single junction TPV cells are in the range of 20e45%, depending on the semiconductor bandgap and quality, and the photon recycling efficiency. This concept has the potential to achieve output electric energy densities in the range of 200-450 kWhe/m3, which is comparable to the best performing state of the art Lithium-ion batteries.