Drifting plasma collection by a positive biased tether wire in LEO-like plasma conditions: current measurement and plasma diagnostic

BETs is a three-year project financed by the Space Program of the European Commission, aimed at developing an efficient deorbit system that could be carried on board any future satellite launched into Low Earth Orbit (LEO). The operational system involves a conductive tape-tether left bare to establish anodic contact with the ambient plasma as a giant Langmuir probe. As a part of this project, we are carrying out both numerical and experimental approaches to estimate the collected current by the positive part of the tether. This paper deals with experimental measurements performed in the IONospheric Atmosphere Simulator (JONAS) plasma chamber of the Onera-Space Environment Department. The JONAS facility is a 9- m3 vacuum chamber equipped with a plasma source providing drifting plasma simulating LEO conditions in terms of density and temperature. A thin metallic cylinder, simulating the tether, is set inside the chamber and polarized up to 1000 V. The Earth's magnetic field is neutralized inside the chamber. In a first time, tether collected current versus tether polarization is measured for different plasma source energies and densities. In complement, several types of Langmuir probes are used at the same location to allow the extraction of both ion densities and electron parameters by computer modeling (classical Langmuir probe characteristics are not accurate enough in the present situation). These two measurements permit estimation of the discrepancies between the theoretical collection laws, orbital motion limited law in particular, and the experimental data in LEO-like conditions without magnetic fields. In a second time, the spatial variations and the time evolutions of the plasma properties around the tether are investigated. Spherical and emissive Langmuir probes are also used for a more extensive characterization of the plasma in space and time dependent analysis. Results show the ion depletion because of the wake effect and the accumulation of- ions upstream of the tether. In some regimes (at large positive potential), oscillations are observed on the tether collected current and on Langmuir probe collected current in specific sites.

Multiple removal of spent rocket upper stages with an ion beam shepherd

Among the many advantages of the recently proposed ion beam shepherd (IBS) debris removal technique is the capability to deal with multiple targets in a single mission. A preliminary analysis is here conducted in order to estimate the cost in terms of spacecraft mass and total mission time to remove multiple large-size upper stages of the Zenit family. Zenit-2 upper stages are clustered at 71 degrees inclination around 850 km altitude in low Earth orbit. It is found that a removal of two targets per year is feasible with a modest size spacecraft. The most favorable combinations of targets are outlined.

Bare-tape scaling laws for de-orbit missions in a space debris environment

El entorno espacial actual hay un gran numero de micro-meteoritos y basura espacial generada por el hombre, lo cual plantea un riesgo para la seguridad de las operaciones en el espacio. La situación se agrava continuamente a causa de las colisiones de basura espacial en órbita, y los nuevos lanzamientos de satélites. Una parte significativa de esta basura son satélites muertos, y fragmentos de satélites resultantes de explosiones y colisiones de objetos en órbita. La mitigación de este problema se ha convertido en un tema de preocupación prioritario para todas las instituciones que participan en operaciones espaciales. Entre las soluciones existentes, las amarras electrodinámicas (EDT) proporcionan un eficiente dispositivo para el rápido de-orbitado de los satélites en órbita terrestre baja (LEO), al final de su vida útil. El campo de investigación de las amarras electrodinámicas (EDT) ha sido muy fructífero desde los años 70. Gracias a estudios teóricos, y a misiones para la demostración del funcionamiento de las amarras en órbita, esta tecnología se ha desarrollado muy rápidamente en las últimas décadas. Durante este período de investigación, se han identificado y superado múltiples problemas técnicos de diversa índole. Gran parte del funcionamiento básico del sistema EDT depende de su capacidad de supervivencia ante los micro-meteoritos y la basura espacial. Una amarra puede ser cortada completamente por una partícula cuando ésta tiene un diámetro mínimo. En caso de corte debido al impacto de partículas, una amarra en sí misma, podría ser un riesgo para otros satélites en funcionamiento. Por desgracia, tras varias demostraciones en órbita, no se ha podido concluir que este problema sea importante para el funcionamiento del sistema. En esta tesis, se presenta un análisis teórico de la capacidad de supervivencia de las amarras en el espacio. Este estudio demuestra las ventajas de las amarras de sección rectangular (cinta), en cuanto a la probabilidad de supervivencia durante la misión, frente a las amarras convencionales (cables de sección circular). Debido a su particular geometría (longitud mucho mayor que la sección transversal), una amarra puede tener un riesgo relativamente alto de ser cortado por un único impacto con una partícula de pequeñas dimensiones. Un cálculo analítico de la tasa de impactos fatales para una amarra cilindrica y de tipo cinta de igual longitud y masa, considerando el flujo de partículas de basura espacial del modelo ORDEM2000 de la NASA, muestra mayor probabilidad de supervivencia para las cintas. Dicho análisis ha sido comparado con un cálculo numérico empleando los modelos de flujo el ORDEM2000 y el MASTER2005 de ESA. Además se muestra que, para igual tiempo en órbita, una cinta tiene una probabilidad de supervivencia un orden y medio de magnitud mayor que una amarra cilindrica con igual masa y longitud. Por otra parte, de-orbitar una cinta desde una cierta altitud, es mucho más rápido, debido a su mayor perímetro que le permite capturar más corriente. Este es un factor adicional que incrementa la probabilidad de supervivencia de la cinta, al estar menos tiempo expuesta a los posibles impactos de basura espacial. Por este motivo, se puede afirmar finalmente y en sentido práctico, que la capacidad de supervivencia de la cinta es bastante alta, en comparación con la de la amarra cilindrica. El segundo objetivo de este trabajo, consiste en la elaboración de un modelo analítico, mejorando la aproximación del flujo de ORDEM2000 y MASTER2009, que permite calcular con precisión, la tasa de impacto fatal al año para una cinta en un rango de altitudes e inclinaciones, en lugar de unas condiciones particulares. Se obtiene el numero de corte por un cierto tiempo en función de la geometría de la cinta y propiedades de la órbita. Para las mismas condiciones, el modelo analítico, se compara con los resultados obtenidos del análisis numérico. Este modelo escalable ha sido esencial para la optimización del diseño de la amarra para las misiones de de-orbitado de los satélites, variando la masa del satélite y la altitud inicial de la órbita. El modelo de supervivencia se ha utilizado para construir una función objetivo con el fin de optimizar el diseño de amarras. La función objectivo es el producto del cociente entre la masa de la amarra y la del satélite y el numero de corte por un cierto tiempo. Combinando el modelo de supervivencia con una ecuación dinámica de la amarra donde aparece la fuerza de Lorentz, se elimina el tiempo y se escribe la función objetivo como función de la geometría de la cinta y las propietades de la órbita. Este modelo de optimización, condujo al desarrollo de un software, que esta en proceso de registro por parte de la UPM. La etapa final de este estudio, consiste en la estimación del número de impactos fatales, en una cinta, utilizando por primera vez una ecuación de límite balístico experimental. Esta ecuación ha sido desarollada para cintas, y permite representar los efectos tanto de la velocidad de impacto como el ángulo de impacto. Los resultados obtenidos demuestran que la cinta es altamente resistente a los impactos de basura espacial, y para una cinta con una sección transversal definida, el número de impactos críticos debidos a partículas no rastreables es significativamente menor. ABSTRACT The current space environment, consisting of man-made debris and tiny meteoroids, poses a risk to safe operations in space, and the situation is continuously deteriorating due to in-orbit debris collisions and to new satellite launches. Among these debris a significant portion is due to dead satellites and fragments of satellites resulted from explosions and in-orbit collisions. Mitigation of space debris has become an issue of first concern for all the institutions involved in space operations. Bare electrodynamic tethers (EDT) can provide an efficient mechanism for rapid de-orbiting of defunct satellites from low Earth orbit (LEO) at end of life. The research on EDT has been a fruitful field since the 70’s. Thanks to both theoretical studies and in orbit demonstration missions, this technology has been developed very fast in the following decades. During this period, several technical issues were identified and overcome. The core functionality of EDT system greatly depends on their survivability to the micrometeoroids and orbital debris, and a tether can become itself a kind of debris for other operating satellites in case of cutoff due to particle impact; however, this very issue is still inconclusive and conflicting after having a number of space demonstrations. A tether can be completely cut by debris having some minimal diameter. This thesis presents a theoretical analysis of the survivability of tethers in space. The study demonstrates the advantages of tape tethers over conventional round wires particularly on the survivability during the mission. Because of its particular geometry (length very much larger than cross-sectional dimensions), a tether may have a relatively high risk of being severed by the single impact of small debris. As a first approach to the problem, survival probability has been compared for a round and a tape tether of equal mass and length. The rates of fatal impact of orbital debris on round and tape tether, evaluated with an analytical approximation to debris flux modeled by NASA’s ORDEM2000, shows much higher survival probability for tapes. A comparative numerical analysis using debris flux model ORDEM2000 and ESA’s MASTER2005 shows good agreement with the analytical result. It also shows that, for a given time in orbit, a tape has a probability of survival of about one and a half orders of magnitude higher than a round tether of equal mass and length. Because de-orbiting from a given altitude is much faster for the tape due to its larger perimeter, its probability of survival in a practical sense is quite high. As the next step, an analytical model derived in this work allows to calculate accurately the fatal impact rate per year for a tape tether. The model uses power laws for debris-size ranges, in both ORDEM2000 and MASTER2009 debris flux models, to calculate tape tether survivability at different LEO altitudes. The analytical model, which depends on tape dimensions (width, thickness) and orbital parameters (inclinations, altitudes) is then compared with fully numerical results for different orbit inclinations, altitudes and tape width for both ORDEM2000 and MASTER2009 flux data. This scalable model not only estimates the fatal impact count but has proved essential in optimizing tether design for satellite de-orbit missions varying satellite mass and initial orbital altitude and inclination. Within the frame of this dissertation, a simple analysis has been finally presented, showing the scalable property of tape tether, thanks to the survivability model developed, that allows analyze and compare de-orbit performance for a large range of satellite mass and orbit properties. The work explicitly shows the product of tether-to-satellite mass-ratio and fatal impact count as a function of tether geometry and orbital parameters. Combining the tether dynamic equation involving Lorentz drag with space debris impact survivability model, eliminates time from the expression. Hence the product, is independent of tether de-orbit history and just depends on mission constraints and tether length, width and thickness. This optimization model finally led to the development of a friendly software tool named BETsMA, currently in process of registration by UPM. For the final step, an estimation of fatal impact rate on a tape tether has been done, using for the first time an experimental ballistic limit equation that was derived for tapes and accounts for the effects of both the impact velocity and impact angle. It is shown that tape tethers are highly resistant to space debris impacts and considering a tape tether with a defined cross section, the number of critical events due to impact with non-trackable debris is always significantly low.

Tether radiation in Juno-type and circular-equatorial Jovian orbits

Wave radiation by a conductor carrying a steady current in both a polar, highly eccentric, low perijove orbit, as in NASA's planned Juno mission, and an equatorial low Jovian orbit (LJO) mission below the intense radiation belts, is considered. Both missions will need electric power generation for scientific instruments and communication systems. Tethers generate power more efficiently than solar panels or radioisotope power systems (RPS). The radiation impedance is required to determine the current in the overall tether circuit. In a cold plasma model, radiation occurs mainly in the Alfven and fast magnetosonic modes, exhibiting a large refraction index. The radiation impedance of insulated tethers is determined for both modes and either mission. Unlike the Earth ionospheric case, the low-density, highly magnetized Jovian plasma makes the electron gyrofrequency much larger than the plasma frequency; this substantially modifies the power spectrum for either mode by increasing the Alfven velocity. Finally, an estimation of the radiation impedance of bare tethers is considered. In LJO, a spacecraft orbiting in a slow downward spiral under the radiation belts would allow determining magnetic field structure and atmospheric composition for understanding the formation, evolution, and structure of Jupiter. Additionally, if the cathodic contactor is switched off, a tether floats electrically, allowing e-beam emission that generate auroras. On/off switching produces bias/current pulses and signal emission, which might be used for Jovian plasma diagnostics.

A "Free-Lunch" tour of the Jovian System

An ED-tether mission to Jupiter is presented. A bare tether carrying cathodic devices at both ends but no power supply, and using no propellant, could move 'freely' among Jupiter's 4 great moons. The tour scheme would have current naturally driven throughout by the motional electric field, the Lorentz force switching direction with current around a 'drag' radius of 160,00 kms, where the speed of the jovian ionosphere equals the speed of a spacecraft in circular orbit. With plasma density and magnetic field decreasing rapidly with distance from Jupiter, drag/thrust would only be operated in the inner plasmasphere, current being near shut off conveniently in orbit by disconnecting cathodes or plugging in a very large resistance; the tether could serve as its own power supply by plugging in an electric load where convenient, with just some reduction in thrust or drag. The periapsis of the spacecraft in a heliocentric transfer orbit from Earth would lie inside the drag sphere; with tether deployed and current on around periapsis, magnetic drag allows Jupiter to capture the spacecraft into an elliptic orbit of high eccentricity. Current would be on at succesive perijove passes and off elsewhere, reducing the eccentricity by lowering the apoapsis progressively to allow visits of the giant moons. In a second phase, current is on around apoapsis outside the drag sphere, rising the periapsis until the full orbit lies outside that sphere. In a third phase, current is on at periapsis, increasing the eccentricity until a last push makes the orbit hyperbolic to escape Jupiter. Dynamical issues such as low gravity-gradient at Jupiter and tether orientation in elliptic orbits of high eccentricity are discussed.

Electrodynamic tether for scientific mission in low Jovian orbit

An electrodynamic bare tether is shown to allow carrying out scientific observations very close to Jupiter, for exploration of its surface and subsurface, and ionospheric and atmospheric in-situ measurements. Starting at a circular equatorial orbit of radius about 1.3/1.4 times the Jovian radius, continuous propellantless Lorentz drag on a thin-tape tether in the 1-5 km length range would make a spacecraft many times as heavy as the tape slowly spiral in, over a period of many months, while generating power at a load plugged in the tether circuit for powering instruments in science data acquisition and transmission. Lying under the Jovian radiation belts, the tape would avoid the most severe problem facing tethers in Jupiter, which are capable of producing both power and propulsion but, operating slowly, could otherwise accumulate too high a radiation dose . The tether would be made to spin in its orbit to keep taut; how to balance the Lorentz torque is discussed. Constraints on heating and bowing are also discussed, comparing conditions for prograde versus retrograde orbits. The system adapts well to the moderate changes in plasma density and motional electric field through the limited radial range in their steep gradients near Jupiter.

High Fidelity Models for Near-Earth Object Dynamics

Motivado por los últimos hallazgos realizados gracias a los recientes avances tecnológicos y misiones espaciales, el estudio de los asteroides ha despertado el interés de la comunidad científica. Tal es así que las misiones a asteroides han proliferado en los últimos años (Hayabusa, Dawn, OSIRIX-REx, ARM, AIMS-DART, ...) incentivadas por su enorme interés científico. Los asteroides son constituyentes fundamentales en la evolución del Sistema Solar, son además grandes concentraciones de valiosos recursos naturales, y también pueden considerarse como objectivos estratégicos para la futura exploración espacial. Desde hace tiempo se viene especulando con la posibilidad de capturar objetos próximos a la Tierra (NEOs en su acrónimo anglosajón) y acercarlos a nuestro planeta, permitiendo así un acceso asequible a los mismos para estudiarlos in-situ, explotar sus recursos u otras finalidades. Por otro lado, las asteroides se consideran con frecuencia como posibles peligros de magnitud planetaria, ya que impactos de estos objetos con la Tierra suceden constantemente, y un asteroide suficientemente grande podría desencadenar eventos catastróficos. Pese a la gravedad de tales acontecimientos, lo cierto es que son ciertamente difíciles de predecir. De hecho, los ricos aspectos dinámicos de los asteroides, su modelado complejo y las incertidumbres observaciones hacen que predecir su posición futura con la precisión necesaria sea todo un reto. Este hecho se hace más relevante cuando los asteroides sufren encuentros próximos con la Tierra, y más aún cuando estos son recurrentes. En tales situaciones en las cuales fuera necesario tomar medidas para mitigar este tipo de riesgos, saber estimar con precisión sus trayectorias y probabilidades de colisión es de una importancia vital. Por ello, se necesitan herramientas avanzadas para modelar su dinámica y predecir sus órbitas con precisión, y son también necesarios nuevos conceptos tecnológicos para manipular sus órbitas llegado el caso. El objetivo de esta Tesis es proporcionar nuevos métodos, técnicas y soluciones para abordar estos retos. Las contribuciones de esta Tesis se engloban en dos áreas: una dedicada a la propagación numérica de asteroides, y otra a conceptos de deflexión y captura de asteroides. Por lo tanto, la primera parte de este documento presenta novedosos avances de apliación a la propagación dinámica de alta precisión de NEOs empleando métodos de regularización y perturbaciones, con especial énfasis en el método DROMO, mientras que la segunda parte expone ideas innovadoras para la captura de asteroides y comenta el uso del “ion beam shepherd” (IBS) como tecnología para deflectarlos. Abstract Driven by the latest discoveries enabled by recent technological advances and space missions, the study of asteroids has awakened the interest of the scientific community. In fact, asteroid missions have become very popular in the recent years (Hayabusa, Dawn, OSIRIX-REx, ARM, AIMS-DART, ...) motivated by their outstanding scientific interest. Asteroids are fundamental constituents in the evolution of the Solar System, can be seen as vast concentrations of valuable natural resources, and are also considered as strategic targets for the future of space exploration. For long it has been hypothesized with the possibility of capturing small near-Earth asteroids and delivering them to the vicinity of the Earth in order to allow an affordable access to them for in-situ science, resource utilization and other purposes. On the other side of the balance, asteroids are often seen as potential planetary hazards, since impacts with the Earth happen all the time, and eventually an asteroid large enough could trigger catastrophic events. In spite of the severity of such occurrences, they are also utterly hard to predict. In fact, the rich dynamical aspects of asteroids, their complex modeling and observational uncertainties make exceptionally challenging to predict their future position accurately enough. This becomes particularly relevant when asteroids exhibit close encounters with the Earth, and more so when these happen recurrently. In such situations, where mitigation measures may need to be taken, it is of paramount importance to be able to accurately estimate their trajectories and collision probabilities. As a consequence, advanced tools are needed to model their dynamics and accurately predict their orbits, as well as new technological concepts to manipulate their orbits if necessary. The goal of this Thesis is to provide new methods, techniques and solutions to address these challenges. The contributions of this Thesis fall into two areas: one devoted to the numerical propagation of asteroids, and another to asteroid deflection and capture concepts. Hence, the first part of the dissertation presents novel advances applicable to the high accuracy dynamical propagation of near-Earth asteroids using regularization and perturbations techniques, with a special emphasis in the DROMO method, whereas the second part exposes pioneering ideas for asteroid retrieval missions and discusses the use of an “ion beam shepherd” (IBS) for asteroid deflection purposes.

Propellantless deorbiting of space debris by bare electrodynamic tethers : final report

A Space tether is a thin, multi-kilometers long conductive wire, joining a satellite and some opposite end mass, and keeping vertical in orbit by the gravity-gradient. The ambient plasma, being highly conductive, is equipotential in its own co-moving frame. In the tether frame, in relative motion however, there is in the plasma a motional electric field of order of 100 V/km, product of (near) orbital velocity and geomagnetic field. The electromotive force established over the tether length allows plasma contactor devices to collect electrons at one polarized-positive (anodic) end and eject electrons at the opposite end, setting up a current along a standard, fully insulated tether. The Lorentz force exerted on the current by the geomagnetic field itself is always drag; this relies on just thermodynamics, like air drag. The bare tether concept, introduced in 1992 at the Universidad Politécnica de Madrid (UPM), takes away the insulation and has electrons collected over the tether segment coming out polarized positive; the concept rests on 2D (Langmuir probe) current-collection in plasmas being greatly more efficient than 3D collection. A Plasma Contactor ejects electrons at the cathodic end. A bare tether with a thin-tape cross section has much greater perimeter and de-orbits much faster than a (corresponding) round bare tether of equal length and mass. Further, tethers being long and thin, they are prone to cuts by abundant small space debris, but BETs has shown that the tape has a probability of being cut per unit time smaller by more than one order of magnitude than the corresponding round tether (debris comparable to its width are much less abundant than debris comparable to the radius of the corresponding round tether). Also, the tape collects much more current, and de-orbits much faster, than a corresponding multi-line “tape” made of thin round wires cross-connected to survive debris cuts. Tethers use a dissipative mechanism quite different from air drag and can de-orbit in just a few months; also, tape tethers are much lighter than round tethers of equal length and perimeter, which can capture equal current. The 3 disparate tape dimensions allow easily scalable design. Switching the cathodic Contactor off-on allows maneuvering to avoid catastrophic collisions with big tracked debris. Lorentz braking is as reliable as air drag. Tethers are still reasonably effective at high inclinations, where the motional field is small, because the geomagnetic field is not just a dipole along the Earth polar axis. BETs is the EC FP7/Space Project 262972, financed in about 1.8 million euros, from 1 November 2010 to 31 January 2014, and carrying out RTD work on de-orbiting space debris. Coordinated by UPM, it has partners Università di Padova, ONERA-Toulouse, Colorado State University, SME Emxys, DLR–Bremen, and Fundación Tecnalia. BETs work involves 1) Designing, building, and ground-testing basic hardware subsystems Cathodic Plasma Contactor, Tether Deployment Mechanism, Power Control Module, and Tape with crosswise and lengthwise structure. 2) Testing current collection and verifying tether dynamical stability. 3) Preliminary design of tape dimensions for a generic mission, conducive to low system-to-satellite mass ratio and probability of cut by small debris, and ohmic-effects regime of tether current for fast de-orbiting. Reaching TRL 4-5, BETs appears ready for in-orbit demostration.