Revising the Emergency Management Requirements for new generation reactors

The paper presents the application of a new risk-informed methodology for the identification of the Emergency Management Requirements (EMR) to a Generation II, Large size Reactor and a Generation III+ Small Modular Reactor. The results obtained in this test case demonstrate that the actual EMR is conservative, as expected, for the GenII reactor, while the new methodology could be applied for the definition of EMRs for the new generation Nuclear Power Plants, with a possible reduction of the emergency area without loss of safety level. By adopting both probabilistic and deterministic approaches, the study addresses possible accidents and corresponding release scenarios for the two types of reactor, calculates the areas where the accidents have an impact on the population and defines the new EMR considering the health effects on the population.

Code assessment and modelling for Design Basis Accident Analysis of the European sodium fast reactor design. Part I: System description, modelling and benchmarking

The new reactor concepts proposed in the Generation IV International Forum (GIF) are conceived to improve the use of natural resources, reduce the amount of high-level radioactive waste and excel in their reliability and safe operation. Among these novel designs sodium fast reactors (SFRs) stand out due to their technological feasibility as demonstrated in several countries during the last decades. As part of the contribution of EURATOM to GIF the CP-ESFR is a collaborative project with the objective, among others, to perform extensive analysis on safety issues involving renewed SFR demonstrator designs. The verification of computational tools able to simulate the plant behaviour under postulated accidental conditions by code-to-code comparison was identified as a key point to ensure reactor safety. In this line, several organizations employed coupled neutronic and thermal-hydraulic system codes able to simulate complex and specific phenomena involving multi-physics studies adapted to this particular fast reactor technology. In the “Introduction” of this paper the framework of this study is discussed, the second section describes the envisaged plant design and the commonly agreed upon modelling guidelines. The third section presents a comparative analysis of the calculations performed by each organisation applying their models and codes to a common agreed transient with the objective to harmonize the models as well as validating the implementation of all relevant physical phenomena in the different system codes.

Code assessment and modelling for Design Basis Accident analysis of the European Sodium Fast Reactor design. Part II: Optimised core and representative transients analysis

The new reactor concepts proposed in the Generation IV International Forum require the development and validation of computational tools able to assess their safety performance. In the first part of this paper the models of the ESFR design developed by several organisations in the framework of the CP-ESFR project were presented and their reliability validated via a benchmarking exercise. This second part of the paper includes the application of those tools for the analysis of design basis accident (DBC) scenarios of the reference design. Further, this paper also introduces the main features of the core optimisation process carried out within the project with the objective to enhance the core safety performance through the reduction of the positive coolant density reactivity effect. The influence of this optimised core design on the reactor safety performance during the previously analysed transients is also discussed. The conclusion provides an overview of the work performed by the partners involved in the project towards the development and enhancement of computational tools specifically tailored to the evaluation of the safety performance of the Generation IV innovative nuclear reactor designs.

Passive neutron area monitor with pairs of TLDs as neutron detector

A passive neutron area monitor has been designed using Monte Carlo methods; the monitor is a polyethylene cylinder with pairs of thermoluminescent dosimeters (TLD600 and TLD700) as thermal neutron detector. The monitor was calibrated with a bare and a thermalzed 241AmBe neutron sources and its performance was evaluated measuring the ambient dose equivalent due to photoneutrons produced by a 15 MV linear accelerator for radiotherapy and the neutrons in the output of a TRIGA Mark III radial beam port.

Induced thermo-mechanical stress in CPV receivers with cycled high intensity light

CPV receivers are made of materials with very different lineal expansion coefficients. Strong variations in DNI due to the passage of clouds can cause sudden temperature changes that creates mechanical stress. For common solder and metal filled polymers the plastic limit could be reached causing substantial fatigue. The best forecast of receiver reliability is therefore achieved by applying an intermittent light source with nominal irradiance level and a number of cycles equal to the expected cloud passages for a given site. The UPM has developed specialized equipment, dubbed the LYSS (Light cYcling Stressing Source), for carrying out such experiments. The small thermal capacity of receivers allows simulating more than 25000 cycles per week. The number of deep transients expected for Madrid in 30 years operation, based on available data, is about 45000. We are currently using the system to cycle a ?Ge/Ag Epoxy/aluminum? receiver, which shows no degradation after 20000 cycles. The equipment can cast up to 200 and 70 W/cm2 on 0.1 and 1 cm2 cells, respectively.

Analysis of thermo-mechanical stress effects on CPV receiver under high intensity light cycles

After construction of the LYSS (Light cYcling Stressing Source) in early 2014, several CPV receivers, with and without secondary optical element (SOE) have been aged under fast transient illumination cycling,. The test plan for Madrid consisted of 50000 cycles. Receivers with poor heat spreaders showed low reliability but those with thicker metal layers passed the test well. The operation of LYSS along 8 months, after more than 250000 cycles, did not show any significant failure, except lamp reposition every 120 hours, in average. The equipment seems valid for unveiling weak receiver designs with respect to intensive illumination, in steady and transient modes.

Evolución de las características en micrófonos electret

A la hora del estudio de los fenómenos acústicos, es necesario el conocimiento de las características técnicas de los elementos utilizados. Un parte importante de ello son los micrófonos, sus características son esenciales para la obtención y comparación de los datos. Intentando describirlas, este trabajo quiere presentar un estudio detallado de una de las características que influyen en ellos, la característica de vida, especializándose en un tipo de micrófonos, los electret. La metodología seguida para el estudio de estos micrófonos se basa en la recopilación de información tras ensayos a diferentes temperaturas con el fin de caracterizarlos según las distintas distribuciones de vida existentes. En cuanto a los contenidos, se comienza explicando una base histórica de estos, origen, características generales y su evolución a lo largo de los años. Seguidamente se especifica una base teórica sobre distintas características que los afectan, antecedentes, y una explicación de las distintas distribuciones y formas del cálculo de vida. Posteriormente comienza la explicación del material utilizado, así como todas las características, para poder explicar la realización del estudio. Para ello: - Se han realizado tres ensayos a diferentes temperaturas, 140º, 125º y 110º dentro de una cámara térmica - Cada ensayo ha constado de diez micrófonos - El número de horas dentro de la cámara térmica ha variado dependiendo de la temperatura a la que se sometían los micrófonos en cada ensayo. - Tras cada hora se ha realizado una medida de cada uno de los micrófonos del nivel de presión sonora a la entrada, con el fin de ir comparándolos tras cada tiempo dentro de la cámara térmica. - Finalmente se ha realizado un estudio de fiabilidad con el que se ha obtenido el tiempo de vida. ABSTRACT. When the study of acoustic phenomena, the knowledge of technical characteristics for the different elements used is needed. An important part of this are the microphones, their characteristics are essential for obtaining and comparing data. Trying to describe it, this paper wants to present a detailed analysis of one of the characteristics that influence them, the characteristic of life, focusing in one type of microphones, the electret. The methodology for the study of these microphones is based on gathering information after some test at different temperatures in order to characterize them with different existing distributions of life. As for the contents, begins with a historical basis of them, origin, general characteristics and their evolution through the years. Afterward a theoretical background on different characteristics that affect them, history and an explanation of different distributions for calculating life forms. Then it begins with the explanation of the material used, as well as the features, in order to explain the study. For that: - There were three test at different temperatures, 140º, 125º and 110º in a thermal camera - Each test has consisted in ten microphones - The number of hours inside the thermal camera has varied depending on the subjected test which the microphones were - After each hour, it has been made a measurement of each microphone of their sound level pressure, in order to compare them after every hour inside the thermal camera - Finally, it has been made a reliability study to obtain their lifetime

Induced radioisotopes in a linac treatment hall

When linacs operate above 8MV an undesirable neutron field is produced whose spectrum has three main components: the direct spectrum due to those neutrons leaking out from the linac head, the scattered spectrum due to neutrons produced in the head that collides with the nuclei in the head losing energy and the third spectrum due to room-return effect. The third category of spectrum has mainly epithermal and thermal neutrons being constant at any location in the treatment hall. These neutrons induce activation in the linac components, the concrete walls and in the patient body. Here the induced radioisotopes have been identified in concrete samples located in the hall and in one of the wedges. The identification has been carried out using a gamma-ray spectrometer.

Archivo Eduardo Torroja. La sede del itcc (1949-1953). Inéditos anteproyectos previos a su construcción

El contenido de este artículo representa el eslabón que falta en la historia publicada por la revista Informes de la Construcción sobre el proyecto y construcción de la nueva sede del Instituto, que fue el hábitat de investigación más innovador jamás construido por la Modernidad. Su difusión completa y cierra esta historia, a la vez que potencia el mensaje que Eduardo Torroja quiso transmitir agrupando los artículos que relatan esta historia, bajo un mismo título común; “El Instituto es Así”, seguramente porque durante mucho tiempo (1949-1953), defendió que no podía ser de otra manera.

Análisis de imágenes basado en correlación de imágenes

El objetivo principal del proyecto es la realización de una aplicación en el programa MATLAB. En primer lugar, realizaremos un estudio teórico relativo al tema de nuestro proyecto. En nuestro caso como el tema es Imagen y Televisión, explicaremos de forma teórica la información principal acerca del Tratamiento Digital de la Imagen. Una vez conocida las técnicas principales utilizadas en el tratamiento digital, realizaremos un estudio exhaustivo en las técnicas actuales que existen acerca del análisis de imágenes. Daremos una breve explicación mostrando en qué consiste esta técnica, los diferentes pasos que se llevan a cabo en una imagen para su análisis, explicando brevemente cada unos de ellos y enumerando algunas técnicas para la realización de cada una de ellas. Tras esta primera parte, nos centraremos en las técnicas de correlación de imágenes (DIC). Explicaremos como han surgido estas técnicas, cual son sus principales conceptos, sus inicios y las ventajas e inconvenientes que tienen. Dentro de las diferentes técnicas de correlación de imágenes, explicaremos de forma detallada la correspondencia por áreas, ya que es la técnica que vamos a utilizar para la realización del proyecto. Explicaremos en qué consiste, y desarrollaremos teóricamente cual son los pasos que se deben realizar en las imágenes para realizar esta técnica. Explicaremos cual es su terminología, y cuáles son los posibles defectos que puede tener esta técnica. Finalmente, una vez estudiada la teoría, realizaremos una sencilla aplicación que nos permita evaluar y encontrar las diferencias en una secuencia de imágenes. El programa utilizado para este proyecto es MATLAB, que es un programa matemático, utilizado enormemente en el ámbito de la ingeniería. Mediante esta aplicación obtendremos dos figuras, una de ellas donde veremos los vectores de movimiento que existen entre las dos imágenes y la segunda, donde obtendremos el factor de correlación que hay entre las dos imágenes. ABSTRACT OF MY PROJECT The main objective of the project is the development of an application in MATLAB program. Firstly carry out a theoretical study on the topic of our project. In our case as the theme is Picture and Television, we explain the main information about Digital Image Processing. Once known the main techniques used in digital images, we will make a study on current techniques that exist about image analysis. We will give a brief explanation showing what this technique is, the different steps that are performed on an image for analysis, briefly explaining each of them and listing some techniques for performing each. After this first part, we will focus on the techniques of image correlation (DIC). We explain how these techniques have emerged, which are the main concepts, the beginning and the advantages and disadvantages they have. There are different image correlation techniques. We will explain in detail the correspondence areas, as it is the technique that we will use for the project. Explain what it is, which is theoretically and we develop steps that must be performed on the images for this technique. We explain what their terminology is, and what are the possible defects that may have this technique. Finally, having explored the theory images, we will make a simple application that allows us to evaluate and find differences in a sequence of images. The program used for this project is MATLAB, a mathematical program, widely used in the field of engineering. Using this application will get two figures, one where we will see the motion vectors between the two images and the second where we get the correlation factor between the two images.

Germination ecology of the perennial Centaurium somedanum, a specialist species of mountain springs

To improve understanding of how a rare endemic species of Centaurium adapts to a specialized ecological niche, we studied the germination ecology of the mountain spring specialist, C. somedanum, a perennial species restricted to an unusual habitat for this genus. We conducted laboratory experiments with fresh seeds collected from two populations for three consecutive years, to investigate: (1) the effect of temperature and light ongermination; (2) the existence of seed dormancy; and (3) inter-population and inter-annual variation in germinability. Germination occurred only in the light and at relatively low temperatures (15?228C) with no differences between constant and alternating regimes, and a significant decrease at high temperatures (258C and 308C). We found non-deep simple morphophysiological dormancy and variation in seed germinability depending on the year of seed collection. C. somedanum diverged from the common germination characteristics of the genus in: (1) its germination at lower temperatures, which contrasts with what is generally expected in wetland species but could be adaptive in the spring habitat; and (2) its morphophysiological dormancy, which we report here for the first time in the genus and which could be an adaptation to its mountain habitat.

Monitorización y seguimiento del esfuerzo realizado por los estudiantes y de su asistencia a actividades presenciales

Este artículo documenta el planteamiento, la metodología y los primeros resultados de un plan de monitorización detallada del esfuerzo y de asistencia a actividades presenciales por parte de los estudiantes de las titulaciones ofertadas por la Escuela Técnica Superior de Ingenieros Navales de la Universidad Politécnica de Madrid durante el segundo cuatrimestre del curso 2011-2012. Se ha establecido un sistema mecánico de recogida de datos de esfuerzo por parte de los estudiantes utilizando una hoja tipo test especialmente configurada al efecto. Se pasa una hoja en todas y cada una de las actividades presenciales realizadas y en la hoja se solicita información sobre el trabajo "fuera de clase". Se documenta en este artículo cómo se ha estructurado esa hoja, qué tipo de datos se recogen, cómo se tratan mediante una base de datos creada al efecto, qué tipo de análisis se puede realizar y qué resultados preliminares obtenemos de dichos análisis.

Geometría, Estructura y Forma. Centro George Ponpidou

Geometría, Estructura y Forma. Centro George Ponpidou. Jornadas Internacionales de Investigación en Construcción, ?Hitos Estructurales de la Arquitectura y la Ingeniería, Instituto de Ciencias de la Construcción Eduardo Torroja, Consejo Superior de Investigaciones Científicas, Universidad Politécnica de Madrid, Ministerio de Ciencia e Innovación, Madrid, noviembre 2011.

Presentación [del libro "De la construcción a la ciencia. Ayer y hoy de Eduardo Torroja"]

El 27 de agosto se cumplieron los 100 años del nacimiento de Eduardo Torroja Miret (1899-1961), a cuya memoria va dedicada esta reunión conjunta de la Real Academia de Ciencias, a la que perteneció, y de la Academia de Ingeniería. La vida de Torroja transcurre en una de las etapas más agitadas de la historia española, pero también en una de las más fructíferas desde el punto de vista ingenieril. Precisamente esta sesión conjunta de la Academia de Ingeniería y de la Real Academia de Ciencias se plantea no como pura celebración hagiográfica sino como conmemoración, es decir, como oportunidad para reflexionar sobre los temas en los que Torroja tuvo la capacidad de ser precursor y para, tras recordar sus contribuciones, analizar la situación actual.

Teaching and evaluating mechanical vibrations with Matlab®

The study of the response of mechanical systems to external excitations, even in the simplest cases, involves solving second-order ordinary differential equations or systems thereof. Finding the natural frequencies of a system and understanding the effect of variations of the excitation frequencies on the response of the system are essential when designing mechanisms [1] and structures [2]. However, faced with the mathematical complexity of the problem, students tend to focus on the mathematical resolution rather than on the interpretation of the results. To overcome this difficulty, once the general theoretical problem and its solution through the state space [3] have been presented, Matlab®[4] and Simulink®[5] are used to simulate specific situations. Without them, the discussion of the effect of slight variations in input variables on the outcome of the model becomes burdensome due to the excessive calculation time required. Conversely, with the help of those simulation tools, students can easily reach practical conclusions and their evaluation can be based on their interpretation of results and not on their mathematical skills