Experimental and Analytical Study of Masonry Infill Reinforced Concrete Frames Retrofitted with Steel Braces

In the present work a seismic retrofitting technique is proposed for masonry infilled reinforced concrete frames based on the replacement of infill panels by K-bracing with vertical shear link. The performance of this technique is evaluated through experimental tests. A simplified numerical model for structural damage evaluation is also formulated according to the notions and principles of continuum damage mechanics. The proposed model is calibrated with the experimental results. The experimental results have shown an excellent energy dissipation capacity with the proposed technique. Likewise, the numerical predictions with the proposed model are in good agreement with experimental results.

Softening-up mannan-rich cell walls

The softening and degradation of the cell wall (CW), often mannan enriched, is involved in several processes during development of higher plants, such as meristematic growth, fruit ripening, programmed cell death, and endosperm rupture upon germination. Mannans are also the predominant hemicellulosic CW polymers in many genera of green algae. The endosperm CWs of dry seeds often contain mannan polymers, sometimes in the form of galactomannans (Gal-mannans). The endo-beta-mannanases (MANs) that catalyse the random hydrolysis of the beta-linkage in the mannan backbone are one of the main hydrolytic enzymes involved in the loosening and remodelling of CWs. In germinating seeds, the softening of the endosperm seed CWs facilitates the emergence of the elongating radicle. Hydrolysis and mobilization of endosperm Gal-mannans by MANs also provides a source of nutrients for early seedling growth, since Gal-mannan, besides its structural role, serves as a storage polysaccharide. Therefore, the role of mannans and of their hydrolytic enzymes is decisive in the life cycle of seeds. This review updates and discusses the significance of mannans and MANs in seeds and explores the increasing biotechnological potential of MAN enzymes.

Seismic vulnerability analysis of wide-beam buildings in Spain

A number of short-to-mid height RC buildings with wide beams have been constructed in moderate-seismicity areas of Spain. The seismic behavior in the direction of the wide beams appears to be deficient because of low lateral strength, low ductility of the wide beams, big strut compressive forces inside the column-beam connections, and unreliable contribution of the spandrel zones of the wide beams. In the orthogonal direction, the behavior is worse since only the joists and the façade beams contribute to the lateral resistance. The objective is to assess the seismic capability of these structures; further research will involve proposing retrofit strategies. The research approach consists of selecting a number of representative buildings and evaluating their vulnerability by code-type, push-over and dynamic analyses. The cooperation of the masonry infill walls is accounted for. The main conclusion is that the seismic behavior of these buildings is inadequate in most of the situations.

Failure mechanism of reinforced concrete structural walls with and without confinement

This paper presents the results of cyclic loading tests on two large-scale reinforced concrete structural walls that were conducted at Purdue University. One of the walls had confinement reinforcement meeting ACI-318-11 requirements while the other wall did not have any confinement reinforcement. The walls were tested as part of a larger study aimed at indentifying parameters affecting failure modes observed to limit the drift capacity of structural walls in Chile during the Maule Earthquake of 2010. These failure modes include out-of-plane buckling (of the wall rather tan individual reinforcing bars), compression failure, and bond failure. This paper discusses the effects of confinement on failure mode. Distributions of unit strain and curvature obtained with a dense array of non-contact coordinate-tracking targets are also presented.

Medida de la conductividad térmica con el método de la aguja térmica, basado en la fuente lineal de calor transitorio, para su aplicación en los cerramientos de adobes y bloques de tierra comprimida

Existe un creciente interés internacional por el ahorro energético y la sostenibilidad en la edificación con importantes repercusiones en la Arquitectura. La inercia térmica es un parámetro fundamental para poder valorar energéticamente un edificio en condiciones reales. Para ello es necesario cambiar el enfoque tradicional de transmisión de calor en régimen estacionario por otro en régimen dinámico en el que se analizan las ondas térmicas y el flujo de calor oscilante que atraviesan los cerramientos. Los parámetros que definen la inercia térmica son: el espesor, la difusividad y el ciclo térmico. A su vez la difusividad está determinada por la conductividad térmica, la densidad y el calor específico del material. De estos parámetros la conductividad es el más complejo, variable y difícil de medir, especialmente en los cerramientos de tierra debido a su heterogeneidad y complejidad higrotérmica. En general, los métodos de medida de la conductividad o transmitancias en los paramentos presentan inconvenientes a la hora de medir un edificio construido con tierra: dificultades de implementación, el elevado coste o la fiabilidad de los resultados, principalmente. El Método de la Aguja Térmica (MAT) se basa en el principio de la evolución en el tiempo del calor emitido por una fuente lineal al insertarse en el seno de un material. Se ha escogido este método porque resulta práctico, de bajo coste y de fácil aplicación a gran escala pero tiene serios problemas de fiabilidad y exactitud. En esta tesis se desarrolla un método de medida de la conductividad térmica para Piezas de Albañilería de Tierra Cruda en laboratorio basado en el MAT, se mejora su fiabilidad, se analiza su incertidumbre, se compara con otros métodos de referencia y se aplica en adobes, Bloques de Tierra Comprimida y probetas de tierra estabilizada con distintas proporciones de paja. Este método servirá de base a una posterior aplicación in situ. Finalmente se proponen modelos matemáticos para mejorar la exactitud del dispositivo utilizado y para la estimación de la conductividad de cerramientos de tierra en función de su densidad. Con los resultados obtenidos se analizan las posibilidades de amortiguación y retardo de las ondas térmicas y capacidad de almacenaje de energía de los cerramientos en función de su densidad y humedad. There is growing international interest in energy saving and sustainability in buildings with significant impact on Architecture. Thermal inertia is a key parameter to assess energy in buildings in real conditions. This requires changing the traditional approach to heat transfer in steady state by another in dynamic regime which analyzes the thermal waves and oscillating heat flux passing through the external walls. The parameters defining the thermal inertia are: the thickness, the diffusivity and the thermal cycle. In turn, the diffusivity is determined by the thermal conductivity, density and specific heat of the material. Of these parameters, thermal conductivity is the most complex, variable and difficult to measure, especially in earth walls due to their heterogeneity and hygrothermal complexity. In general, the methods of measurement of conductivity and transmittance in walls have drawbacks when measuring a building with earth: implementation difficulties, high cost, or reliability of the results, mainly. The Thermal Needle Procedure (TNP) is based on the principle of evolution in time of heat from a line source when inserted within a material. This method was chosen because it is a practical, low cost and easy to implement on a large scale but has serious problems of reliability and accuracy. This thesis develops a laboratory method for measuring the thermal conductivity of Masonry Units Unfire Earth-based based on TNP, its uncertainty is analyzed, compared to other reference methods and applies in adobes, Compressed Earth Blocks and stabilized soil specimens with different proportions of straw. This method will form the basis of a subsequent application in situ. Finally, mathematical models are proposed to improve the accuracy of the device used, and to estimate the conductivity of earth enclosures depending on its density. With the results obtained earth enclosures are analyzed to estimate their possibilities of delay and buffer of termal waves and energy storage capacity according to their density and moisture.

Geographical cataloguing of earthen architecture in Soria, Spain

This paper discusses the most relevant earth construction techniques that have been employed in the province of Soria (Spain). The objectives of the research are, first, to locate and catalogue each building techniques with earth within the geographic regions and environmental units and their relation to physical and human environment. Then, the second aim is analyze these techniques and characterize them in terms of material, components and construction processes. Three types are studied: the construction of rammed-earth walls, adobe masonry and timber frame filled with adobe.

Fundamentos constructivos de las fortificaciones fronterizas entre las coronas de Castilla y Aragón de los siglos XII al XV en la actual provincia de Soria

La tesis doctoral desarrolla una investigación original, dentro del marco disciplinario de la historia de la construcción, sobre los fundamentos constructivos de las fortificaciones bajomedievales fronterizas entre las Coronas de Castilla y Aragón en la actual provincia de Soria. En el título de la tesis ya queda expresado el objeto fundamental y fundacional, así como el ámbito temporal —desde la reconquista del oriente soriano por parte de Alfonso I el Batallador a principios del siglo XII hasta la unificación de las coronas hispánicas en el siglo XV bajo el común mandato de los Reyes Católicos— y la extensión territorial que delimita la investigación: aquéllas comarcas castellanas lindantes con Aragón pertenecientes a la actual provincia de Soria. Durante este período bajomedieval se produjeron una serie de enfrentamientos fronterizos que obligó a fortificar la frontera y las vías de comunicación entre ambas coronas. La falta de estudios de conjunto de estas fortificaciones entendiéndolas como participantes en un sistema fortificado ha constituido la justificación de la investigación, que se realiza en varios niveles de análisis: territorial, histórico, arquitectónico, poliorcético y constructivo. Así mismo, se ha detectado cierta falta de rigor acompañada de inexactitudes en las consideraciones constructivas publicadas sobre algunas de las fortificaciones del ámbito de estudio, lo que ha provocado errores en su datación al no más haber elementos de corte artístico o estilístico que marquen indudablemente la pertenencia a una época. En la tesis se ponen en duda las dataciones tradicionalmente aceptadas planteando la hipótesis que da pie a la investigación: ante la falta de elementos artísticos o estilísticos en unos sobrios edificios eminentemente funcionales es posible establecer con suficiente aproximación la fecha de construcción en base a criterios constructivos una vez formada una clasificación cronotipológica de cada técnica constructiva. La hipótesis, por lo tanto, plantea un objetivo principal —el estudio de la razón constructiva del sistema fortificado fronterizo— desarrollado en una serie de objetivos específicos cuya consecución programa los sucesivos niveles de análisis: - Conocer y detallar los elementos históricos que originaron los enfrentamientos entre las Coronas de Castilla y Aragón y su desarrollo mediante herramientas historiográficas y analizar las características naturales del territorio en litigio mediante instrumentos cartográficos. - Conocer y analizar los tipos arquitectónicos y las tradiciones constructivas empleadas en las construcciones castrenses en el ámbito temporal en que se enmarca la investigación. - Localizar, documentar y seleccionar para su análisis las fortalezas y construcciones militares erigidas durante dichas luchas fronterizas en la actual provincia de Soria a través del trabajo de campo y métodos cartográficos y bibliográficos. - Realizar un estudio general sobre el sistema fortificado a escala territorial - Investigar la tipología arquitectónica, poliorcética y constructiva del conjunto de estas fortificaciones bajomedievales fronterizas. - Analizar los fundamentos constructivos de los casos de estudio seleccionados entre estas construcciones y caracterizarlas en cuanto al material, elementos, sistemas y procesos constructivos. - Ordenar la información histórica dispersa y corregir errores para hacer una base sobre la que establecer un discurso histórico de cada caso de estudio. - Comparar y relacionar las técnicas constructivas empleadas en estas fortalezas con los utilizados en el mismo ámbito temporal. - Difundir para su debate los resultados de la investigación por los foros científicos habituales. El método empleado combina los trabajos de gabinete con una intensa labor de campo, en la que se han documentado cincuenta fortificaciones y se han redactado sus correspondientes fichas de toma de datos. La recopilación de datos se ha incluido en una base de datos que incluye aspectos generales, tipológicos, constructivos y bibliográficos básicos del conjunto, a modo de inventario, de fortificaciones de la provincia. Las fortificaciones seleccionadas se agrupan según una clasificación tipológica y constructiva que marca las líneas de estudio posteriores. Se desarrolla un capítulo de antecedentes en el que se estudia la historia de la construcción fortificada medieval tanto en Europa como en España analizando la evolución de los tipos arquitectónicos y las múltiples influencias culturales que surcaron el Mediterráneo desde el Oriente cruzado e islámico al Poniente donde se desarrollaba la empresa reconquistadora que mantuvo en estado de guerra continuo a la Península Ibérica durante ochocientos años. El análisis del territorio como contenedor del hecho fortificado revela que hay una relación íntima entre la ubicación de las fortificaciones y las formas naturales que definen las vías de comunicación entre los valles del Duero, del Ebro y del Tajo. En efecto, el ámbito de estudio ha supuesto desde la Antigüedad un territorio de paso fundamental en la articulación de las comunicaciones en la Península Ibérica. Este carácter de paso más que de frontera explica las inquietudes y la preocupación por su control tanto por Roma como por el califato cordobés como por los reinos cristianos medievales. El análisis de los elementos históricos se complementa con el estudio detallado de los enfrentamientos fronterizos entre Castilla y Aragón así como los aspectos sociales y políticos que provocaron la fortificación como sistema de definición de la frontera y de organización espacial, jurisdiccional, social y administrativa del territorio. La arquitectura fortificada es esencialmente funcional: su cometido es la defensa. En este sentido, tras un estudio morfológico de los castillos seleccionados se realiza un extenso análisis poliorcético de sus elementos, investigando su origen y aplicación para servir también de parámetros de datación. Siendo el objeto inaugural de la tesis el estudio de los fundamentos constructivos, se explican los distintos materiales de construcción empleados y se agrupan las fábricas de las fortificaciones seleccionadas en dos grandes grupos constructivos: las fábricas aparejadas y las fábricas encofradas. Se han destacado y estudiado la evolución histórica y la tipología y mensiología constructiva de tres técnicas destacadas: el uso del ladrillo, la tapia de cal y canto o mampostería encofrada y la tapia de tierra. Para el estudio de la componente histórica y de la dimensión constructiva de cada técnica ha sido necesario documentar numerosos casos tanto en el ámbito de estudio como en la Península Ibérica con el fin de establecer grupos cronotipológicos constructivos entre los que poder ubicar las fábricas de estas técnicas presentes en el ámbito de estudio. Se ha observado una evolución dimensional de las fábricas de tapia que es más evidente en las hispanomusulmanas al modularse en codos pero que también se advierte significativamente en las cristianas bajomedievales. De cada una de las técnicas analizadas se ha seleccionado un caso de estudio singular y representativo. El castillo de Arcos de Jalón es un ejemplo significativo del empleo de la fábrica mixta de mampostería con verdugadas de ladrillo, así como las murallas de la ciudad fortificada de Peñalcázar lo es de la fábrica de mampostería encofrada y el castillo de Serón de Nágima constituye un caso característico y principal de la utilización de la tapia de tierra en la arquitectura militar bajomedieval. Cada uno de estos tres casos de estudios se examina bajo los mismos cuatro niveles anteriormente mencionados: territorial, histórico, arquitectónico y defensivo y constructivo. El sistemático método de estudio ha facilitado el orden en la investigación y la obtención de unos resultados y conclusiones que verifican la hipótesis y cumplen los objetivos marcados al comienzo. Se ha revisado la datación en la construcción de las fortificaciones analizadas mediante el estudio cronotipológico de sus fábricas, pudiendo trasladarse el método a otros sistemas fortificados. La tesis abre, finalmente, dos vías principales de investigación encaminadas a completar el estudio del sistema fortificado fronterizo bajomedieval en la raya oriental soriana de Castilla: la caracterización y datación por métodos físico-químicos de las muestras de piezas de madera de construcción que se conservan embebidas en las fábricas y la búsqueda documental y archivística que pueda revelar nuevos datos respecto a la fundación, reparación, venta o cualquier aspecto económico, legislativo, organizativo o administrativo relativo a las fortificaciones en documentos coetáneos. ABSTRACT The doctoral thesis develops an original research, held in the field of the Construction History, about the constructive reason of the frontier fortifications in the Late Middle Age between the Crowns of Castile and Aragón in the actual province of Soria, Spain. In the title is expressed the main objective, and also the temporal scope —from the reconquest in the 12th Century by Alfonso the First of Aragón to the unification under the common kingdom of the Catholic Kings— and the territorial extension that the research delimits: those Castilian regions in the border with Aragón in the actual province of Soria. During this period, a series of border wars were been, and this is the reason for the fortification of the border line and the main roads between both Crowns. The lack of studies of these fortifications as participants in a fortified system is the justification of the research. There is several analysis levels: territorial, historical, architectonic, defensive and constructive. Likewise, there is a lack of strictness and inaccuracy in the constructive items in the publications about several fortifications of this study field. This aspect has caused mistakes in the dating because there is neither artistic nor stylistic elements which determines a epoch. The traditionally accepted datings are challenged. An hypothesis is formulated: in the absence of artistic or stylistic elements in a sober and functional buildings is possible to date the time of construction with sufficiently approximation based on construction criteria once formed a cronotypologic classification of each building technique. The hypothesis, therefore, propose a main aim: the study of the constructive reason of the fortified border system. This aim is developed in a series of specifically targets whose achievement programs the analysis levels: - To know and to detail the historical elements which started the wars between Castile and Aragon and its development using historiographical tools, and to analyze the natural characteristic of the territory through cartographical tools. - To understand and to analyze the different architectural types and the building traditions employed in the military buildings in the time researched. - To locate, to document, and to select for their analysis the fortresses and military constructions erected during these border wars in the actual province of Soria through fieldwork and bibliographical and cartographical methods. - To conduct a general study on the fortified system in territorial scale. - To research the architectural, constructive and defensive typology of the system of these border late medieval fortifications. - To analyze the construction logic of the selected case studies and to characterize in the items of material, elements, systems and construction processes. - To sort scattered historical information and to correct mistakes to make a base by which to establish a historic speech of each case study. - To compare and to relate the construction techniques employed in these fortresses with those used in the same time range . - To spread for discussion the research results in the usual scientists forums. The method combines the destock work with an intense fieldwork. Fifty fortifications have been documented and it has written their corresponding data collection card. Data collection has been included in a database that includes general aspects, typological, constructive and basic bibliographical data, as an inventory of fortifications in the province. The selected fortifications are grouped according to a typological and constructive classification which lead the lines of the later study. There is a chapter for the antecedents in which the history of the medieval fortified construction in Europe and in Spain is studied by analyzing the evolution of architectural types and the many cultural influences along the opposite seasides of the Mediterranean Sea, from the Islamic and Crusader East to the Iberian Peninsula in where there were a long and continuous war during eight hundred years. The territory is analyzed as a container of fortifications. This analysis reveals that there is an intimate relationship between the location of the fortifications and the natural forms that define the communication roads between the Duero, Ebro and Tajo valleys. Indeed, the study area has been a cross-territory from ancient times more than a frontierterritory. This communication character explains the concerns about its control both by Rome and by the Muslims of Córdoba as medieval Christian kingdoms. The analysis of historical elements is supplemented by detailed study of border war between Castile and Aragon and the social and political issues that led to the fortification as border definition system and spatial, jurisdictional, social and administrative planning. The fortified architecture is essentially functional: it is responsible for defense. In this sense, after a morphological study of selected castles is performed an extensive analysis of its defensive elements, investigating its origin and application. This analisis serves for the definition of parameters for dating. The purpose of the thesis is the study of the constructive logic. First, various building materials are explained. Then, masonry is grouped into two major constructive groups: rigged masonry and formwork masonry. The historical evolution and the constructive typology and mensiology are studied for each one of the three main techniques: the use of brickwork, the mortar wall and rammed-earth. Many case studies have been documented along the Iberian Peninsula and also in the study area. As conclusion, there is a dimensional evolution of the rammed-earth walls. This evolution is more evident into the Muslim masonry than in the late medieval walls: the reason is the use of the cubit as module. From each of the techniques discussed, a singular and representative case of study has been selected. The castle of Arcos de Jalon is a significant example of mix masonry of stone and brick rows. The walled city of Peñalcázar is built with masonry formwork. Serón de Nágima castle, at last, is a typical and main case of the use of the rammedearth wall of late medieval military architecture. Each of these three case studies were examined under the same four analysis levels above mentioned: territorial, historical, architectural and defensive and constructive. The systematic method of study has facilitated the order in the research and the obtaining of results and conclusions that verify the hypotheses and achieve the research objectives. Dating of the fortifications construction has been revised by studying the cronotypological issues of its masonry. The method can be transferred to the study of other fortified systems. Finally, the thesis describes two main research new ways aimed at completing the study of the late medieval fortified border of Castile in the actual province of Soria. The first of them is the characterization and datig by physicochemical methods the sample pieces of wood construction preserved embedded in the masonry. The second research way is the investigation of the documents in archives that may reveal new information about the foundation, repair, sale or any aspect to economic, legal, organizational or administrative concerning fortifications in contemporary documents.

On the use of trenches and walls on the control of ground transmitted railway vibrations

An actual case of an underground railway in the neighbourhood of habitation buildings has been analyzed. The study has been based on a twodimensional BEM model including a tunnel and a typical building. The soil properties were obtained using geophysical techniques. After a sensitivity study, the model has been simplyfied and validated by comparison with "in situ" measurements. Using this simplyfied model, a parametric study has been done including trenches and walls of different materials and different depths at two different distances from the tunnel. The reductions obtained with the different solutions can then be compared.

Comportamiento estructural de elementos de fábrica reforzados con materiales compuestos avanzados solicitados a flexión y flexocompresión

El refuerzo de estructuras existentes mediante el encolado exterior de láminas de polímeros reforzados con fibras (FRP) se ha convertido en la aplicación más común de los materiales compuestos avanzados en construcción. Estos materiales presentan muchas ventajas frente a los materiales convencionales (sin corrosión, ligeros, de fácil aplicación, etc.). Pero a pesar de las numerosas investigaciones realizadas, aún persisten ciertas dudas sobre algunos aspectos de su comportamiento y las aplicaciones prácticas se llevan a cabo sólo con la ayuda de guías, sin que haya una normativa oficial. El objetivo de este trabajo es incrementar el conocimiento sobre esta técnica de refuerzo, y más concretamente, sobre el refuerzo a flexión de estructuras de fábrica. Con frecuencia el elemento reforzado es de hormigón armado y las láminas de FRP encoladas al exterior sirven para mejorar su resistencia a flexión, cortante o compresión (encamisados). Sin embargo su empleo en otros materiales como las estructuras de fábrica resulta muy prometedor. Las fábricas se caracterizan por soportar muy bien los esfuerzos de compresión pero bastante mal los de tracción. Adherir láminas de materiales compuestos puede servir para mejorar la capacidad resistente de elementos de fábrica sometidos a esfuerzos de flexión. Pero para ello, debe quedar garantizada una correcta adherencia entre el FRP y la fábrica, especialmente en edificios antiguos cuya superficie puede estar deteriorada por encontrarse a la intemperie o por el propio paso del tiempo. En el capítulo II se describen los objetivos fundamentales del trabajo y el método seguido. En el capítulo III se hace una amplia revisión del estado de conocimiento sobre el tema. En el apartado III.1 se detallan las principales características y propiedades mecánicas de fibras, matrices y materiales compuestos así como sus principales aplicaciones, haciendo especial hincapié en aspectos relativos a su durabilidad. En el apartado III.2 se incluye una revisión histórica de las líneas de investigación, tanto teóricas como empíricas, publicadas sobre estructuras de hormigón reforzadas a flexión encolando materiales compuestos. El apartado III.3 se centra en el aspecto fundamental de la adherencia refuerzo-soporte. Se hace un repaso a distintos modelos propuestos para prevenir el despegue distinguiendo si éste se inicia en la zona de anclaje o si está inducido por fisuras en la zona interior del elemento. Se observa falta de consenso en las propuestas. Además en este punto se relatan las campañas experimentales publicadas acerca de la adherencia entre materiales compuestos y fábricas. En el apartado III.4 se analizan las particularidades de las estructuras de fábrica. Además, se revisan algunas de las investigaciones relativas a la mejora de su comportamiento a flexión mediante láminas de FRP. El comportamiento mecánico de muros reforzados solicitados a flexión pura (sin compresión) ha sido documentado por varios autores, si bien es una situación poco frecuente en fábricas reales. Ni el comportamiento mecánico de muros reforzados solicitados a flexocompresión ni la incidencia que el nivel de compresión soportado por la fábrica tiene sobre la capacidad resistente del elemento reforzado han sido suficientemente tratados. En cuanto a los trabajos teóricos, las diferentes propuestas se basan en los métodos utilizados para hormigón armado y comparten los principios habituales de cálculo. Sin embargo, presentan diferencias relativas, sobre todo, a tres aspectos: 1) la forma de modelar el comportamiento de la fábrica, 2) el valor de deformación de cálculo del refuerzo, y 3) el modo de fallo que se considera recomendable buscar con el diseño. A pesar de ello, el ajuste con la parte experimental de cada trabajo suele ser bueno debido a una enorme disparidad en las variables consideradas. Cada campaña presenta un modo de fallo característico y la formulación que se propone resulta apropiada para él. Parece necesario desarrollar un método de cálculo para fábricas flexocomprimidas reforzadas con FRP que pueda ser utilizado para todos los posibles fallos, tanto atribuibles a la lámina como a la fábrica. En el apartado III.4 se repasan algunas lesiones habituales en fábricas solicitadas a flexión y se recogen ejemplos de refuerzos con FRP para reparar o prevenir estos daños. Para mejorar el conocimiento sobre el tema, se llevan a cabo dos pequeñas campañas experimentales realizadas en el Instituto de Ciencias de la Construcción Eduardo Torroja. La primera acerca de la adherencia de materiales compuestos encolados a fábricas deterioradas (apartado IV.1) y la segunda sobre el comportamiento estructural a flexocompresión de probetas de fábrica reforzadas con estos materiales (apartado IV.2). En el capítulo V se analizan algunos de los modelos de adherencia propuestos para prevenir el despegue del extremo del refuerzo. Se confirma que las predicciones obtenidas con ellos resultan muy dispares. Se recopila una base de datos con los resultados experimentales de campañas sobre adherencia de FRP a fábricas extraídas de la literatura y de los resultados propios de la campaña descrita en el punto IV.1. Esta base de datos permite conocer cual de los métodos analizados resulta más adecuado para dimensionar el anclaje de láminas de FRP adheridas a fábricas. En el capítulo VI se propone un método para la comprobación en agotamiento de secciones de fábrica reforzadas con materiales compuestos sometidas a esfuerzos combinados de flexión y compresión. Está basado en el procedimiento de cálculo de la capacidad resistente de secciones de hormigón armado pero adaptado a las fábricas reforzadas. Para ello, se utiliza un diagrama de cálculo tensión deformación de la fábrica de tipo bilineal (acorde con el CTE DB SE-F) cuya simplicidad facilita el desarrollo de toda la formulación al tiempo que resulta adecuado para predecir la capacidad resistente a flexión tanto para fallos debidos al refuerzo como a la fábrica. Además se limita la deformación de cálculo del refuerzo teniendo en consideración ciertos aspectos que provocan que la lámina adherida no pueda desarrollar toda su resistencia, como el desprendimiento inducido por fisuras en el interior del elemento o el deterioro medioambiental. En concreto, se propone un “coeficiente reductor por adherencia” que se determina a partir de una base de datos con 68 resultados experimentales procedentes de publicaciones de varios autores y de los ensayos propios de la campaña descrita en el punto IV.2. También se revisa la formulación propuesta con ayuda de la base de datos. En el capítulo VII se estudia la incidencia de las principales variables, como el axil, la deformación de cálculo del refuerzo o su rigidez, en la capacidad final del elemento. Las conclusiones del trabajo realizado y las posibles líneas futuras de investigación se exponen en el capítulo VIII. ABSTRACT Strengthening of existing structures with externally bonded fiber reinforced polymers (FRP) has become the most common application of advanced composite materials in construction. These materials exhibit many advantages in comparison with traditional ones (corrosion resistance, light weight, easy to apply, etc.). But despite countless researches have been done, there are still doubts about some aspects of their behaviour and applications are carried out only with the help of guidelines, without official regulations. The aim of this work is to improve the knowledge on this retrofitting technique, particularly in regard to flexural strengthening of masonry structures. Reinforced concrete is often the strengthened material and external glued FRP plates are used to improve its flexural, shear or compressive (by wrapping) capacity. However the use of this technique on other materials like masonry structures looks promising. Unreinforced masonry is characterized for being a good material to support compressive stresses but really bad to withstand tensile ones. Glue composite plates can improve the flexural capacity of masonry elements subject to bending. But a proper bond between FRP sheet and masonry must be ensured to do that, especially in old buildings whose surface can be damaged due to being outside or ageing. The main objectives of the work and the methodology carried out are described In Chapter II. An extensive overview of the state of art is done in Chapter III. In Section III.1 physical and mechanical properties of fibers, matrix and composites and their main applications are related. Durability aspects are especially emphasized. Section III.2 includes an historical overview of theoretical and empirical researches on concrete structures strengthened gluing FRP plates to improve their flexural behaviour. Section III.3 focuses on the critical point of bonding between FRP and substrate. Some theoretical models to prevent debonding of FRP laminate are reviewed, it has made a distinction between models for detachment at the end of the plate or debonding in the intermediate zones due to the effects of cracks. It is observed a lack of agreement in the proposals. Some experimental studies on bonding between masonry and FRP are also related in this chapter. The particular characteristics of masonry structures are analyzed in Section III.4. Besides some empirical and theoretical investigations relative to improve their flexural capacity with FRP sheets are reviewed. The mechanical behaviour of strengthened walls subject to pure bending (without compression) has been established by several authors, but this is an unusual situation for real masonry. Neither mechanical behaviour of walls subject to bending and compression nor influence of axial load in the final capacity of the strengthened element are adequately studied. In regard to theoretical studies, the different proposals are based on reinforced concrete analytical methods and share common design principles. However, they present differences, especially, about three aspects: 1) the constitutive law of masonry, 2) the value of ultimate FRP strain and 3) the desirable failure mode that must be looked for. In spite of them, a good agreement between each experimental program and its theoretical study is often exhibited due to enormous disparity in considered test parameters. Each experimental program usually presents a characteristic failure mode and the proposed formulation results appropriate for this one. It seems necessary to develop a method for FRP strengthened walls subject to bending and compression enable for all failure modes (due to FRP or masonry). Some common damages in masonry subject to bending are explained in Section III.4. Examples of FRP strengthening to repair or prevent these damages are also written. Two small experimental programs are carried out in Eduardo Torroja Institute to improve the knowledge on this topic. The first one is concerned about the bond between FRP plates and damaged masonry (section IV.1) and the second one is related to the mechanical behaviour of the strengthened masonry specimens subject to out of plane bending combined with axial force (section IV.2). In the Chapter V some bond models to prevent the debonding at the FRP plate end are checked. It is confirmed that their predictions are so different. A pure-shear test database is compiled with results from the existing literature and others from the experimental program described in section IV.1. This database lets know which of the considered model is more suitable to design anchorage lengths of glued FRP to masonry. In the Chapter VI a method to check unreinforced masonry sections with external FRP strengthening subject to bending and compression to the ultimate limit state is proposed. This method is based on concrete reinforced one, but it is adapted to strengthened masonry. A bilinear constitutive law is used for masonry (according to CTE DB SE-F). Its simplicity helps to develop the model formulation and it has proven to be suitable to predict bending capacity either for FRP failures or masonry crushing. With regard to FRP, the design strain is limited. It is taken into account different aspects which cause the plate can’t reach its ultimate strength, like intermediate FRP debonding induced by opening cracking or environmental damage. A “bond factor” is proposed. It is obtained by means of an experimental bending test database that includes 68 results from the existing literature and from the experimental program described in section IV.2. The proposed formulation has also been checked with the help of bending database. The effects of the main parameters, like axial load, FRP design effective strain or FRP stiffness, on the bending capacity of the strengthened element are studied in Chapter VII. Finally, the main conclusions from the work carried out are summarized in Chapter VIII. Future lines of research to be explored are suggested as well.

Performance of masonry buildings during the 2011 Lorca earthquake

On Wednesday 11th May 2011 at 6:47 pm (local time) a magnitude 5.1 Mw earthquake occurred 6 km northeast of Lorca with a depth of around 2 km. As a consequence of the shallow depth and the small epicentral distance, important damage was produced in several masonry constructions and even led to the collapse of some of them. Pieces of the facades of several buildings fell down onto the sidewalk, being one of the reasons for the killing of a total of 9 people. The objective of this paper is to describe and analyze the failure patterns observed in unreinforced masonry buildings ranging from 3 to 8 floors in height. First, a brief description of the local building practices of masonry buildings is given. Then, the most important failure types of masonry buildings are described and discussed. After that, a more detailed analysis of one particular building is presented.

Vulnerability analysis of RC buildings with wide beams located in moderate seismicity regions

A significant number of short-to-mid height RC buildings with wide beams have been constructed in areas of moderate seismicity of Spain, mainly for housing and administrative use. The buildings have a framed structure with one-way slabs; the wide beams constitute the distinctive characteristic, their depth being equal to that of the rest of the slab, thus providing a flat lower surface, convenient for construction and the layout of facilities. Seismic behavior in the direction of the wide beams appears to be deficient because of: (i) low lateral strength, mainly because of the small effective depth of the beams, (ii) inherent low ductility of the wide beams, generated by high amount of reinforcement, (iii) the big strut compressive forces developed inside the column-beam connections due to the low height of the beams, and (iv) the fact that the wide beams are wider than the columns, meaning that the contribution of the outer zones to the resistance of the beam-column joints is unreliable because there is no torsion reinforcement. In the orthogonal direction, the behavior is worse since the only members of the slabs that contribute to the lateral resistance are the joists and the façade beams. Moreover, these buildings were designed with codes that did not include ductility requirements and required only a low lateral resistance; indeed, in many cases, seismic action was not considered at all. Consequently, the seismic capacity of these structures is not reliable. The objective of this research is to assess numerically this capability, whereas further research will aim to propose retrofit strategies. The research approach consists of: (i) selecting a number of 3-story and 6-story buildings that represent the vast majority of the existing ones and (ii) evaluating their vulnerability through three types of analyses, namely: code-type, push-over and nonlinear dynamic analysis. Given the low lateral resistance of the main frames, the cooperation of the masonry infill walls is accounted for; for each representative building, three wall densities are considered. The results of the analyses show that the buildings in question exhibit inadequate seismic behavior in most of the examined situations. In general, the relative performance is less deficient for Target Drift CP (Collapse Prevention) than for IO (Immediate Occupancy). Since these buildings are selected to be representative of the vast majority of buildings with wide beams that were constructed in Spain without accounting for any seismic consideration, our conclusions can be extrapolated to a broader scenario.

Assessing construction and demolition waste on masonry works to avoid future generation

The difficulty of dealing with construction and demolition waste (CDW) on construction sites is not new and continues to be a significant environmental problem. Currently the CDW collection system in Spain is done in a decentralized manner by each sub-contracted company, being necessary to implement effective waste management measures ensuring a correct management and minimization. During the last years several measures have been launched in order to improve and encourage the reuse and recycling of CDW. A widespread solution for CDW recovery is using them as a landscaping aggregate or for road bases and sub-bases. However, measures encouraging onsite prevention still need to be enhanced. This paper studies the major work stage generating CDW and analyses the categories of CDW produced during its execution. For this, several real building sites have been analysed in order to quantify the estimation of CDW generated. Results of this study show that a significant contributor to the CDW generation on building construction sites in Spain are the masonry works. Finally, a Best Practices Manual (BPM) is proposed containing several strategies on masonry works aimed not only at CDW prevention, but also at improving their management and minimization. The use of this BPM together with the Study and Plan of CDW management --required by law--, promotes the environmental management of the company, favouring the cohesion of the construction process organization at all stages giving rise to establishing responsibilities in the field of waste and providing a greater control over the process. Keywords: construction and demolition waste, management, masonry works, good practice measures, prevention.

Seismic earth thrust against massive building walls

The problem of earth thrust for a massive building in a seismic environment is analysed. Intertial and kinematic soil-structure interactions are considered by modelling the soil and the structure together. The problem is solved in the frequency domain by using the computer code FLUSH. Results show that the horizontal component of the seismic earth thrust is much greater than that obtained when applying the Mononobe-Okabe theory. This study establishes a set of conclusicns and recommendations for both design and practical purposes, and proposes future lines of investigation.

Assessment of expected damage on buildings subjected to Lorca earthquake through an energy-based seismic index method and nonlinear dynamic response analyses

The city of Lorca (Spain) was hit on May 11th, 2011, by two consecutive earth-quakes of magnitudes 4.6 and 5.2 Mw, causing casualties and important damage in buildings. Many of the damaged structures were reinforced concrete frames with wide beams. This study quantifies the expected level of damage on this structural type in the case of the Lorca earth-quake by means of a seismic index Iv that compares the energy input by the earthquake with the energy absorption/dissipation capacity of the structure. The prototype frames investigated represent structures designed in two time periods (1994–2002 and 2003–2008), in which the applicable codes were different. The influence of the masonry infill walls and the proneness of the frames to concentrate damage in a given story were further investigated through nonlinear dynamic response analyses. It is found that (1) the seismic index method predicts levels of damage that range from moderate/severe to complete collapse; this prediction is consistent with the observed damage; (2) the presence of masonry infill walls makes the structure very prone to damage concentration and reduces the overall seismic capacity of the building; and (3) a proper hierarchy of strength between beams and columns that guarantees the formation of a strong column-weak beam mechanism (as prescribed by seismic codes), as well as the adoption of counter-measures to avoid the negative interaction between non-structural infill walls and the main frame, would have reduced the level of damage from Iv=1 (collapse) to about Iv=0.5 (moderate/severe damage)

Selective injection of magnetic domain walls in Permalloy nanostripes

Selective injection of magnetic domain walls in Permalloy nanostripes