On-line measurement of soil properties without direct spectral response in near infrared spectral range

So far, the majority of reports on on-line measurement considered soil properties with direct spectral responses in near infrared spectroscopy (NIRS). This work reports on the results of on-line measurement of soil properties with indirect spectral responses, e.g. pH, cation exchange capacity (CEC), exchangeable calcium (Caex) and exchangeable magnesium (Mgex) in one field in Bedfordshire in the UK. The on-line sensor consisted of a subsoiler coupled with an AgroSpec mobile, fibre type, visible and near infrared (vis–NIR) spectrophotometer (tec5 Technology for Spectroscopy, Germany), with a measurement range 305–2200 nm to acquire soil spectra in diffuse reflectance mode. General calibration models for the studied soil properties were developed with a partial least squares regression (PLSR) with one-leave-out cross validation, using spectra measured under non-mobile laboratory conditions of 160 soil samples collected from different fields in four farms in Europe, namely, Czech Republic, Denmark, Netherland and UK. A group of 25 samples independent from the calibration set was used as independent validation set. Higher accuracy was obtained for laboratory scanning as compared to on-line scanning of the 25 independent samples. The prediction accuracy for the laboratory and on-line measurements was classified as excellent/very good for pH (RPD = 2.69 and 2.14 and r2 = 0.86 and 0.78, respectively), and moderately good for CEC (RPD = 1.77 and 1.61 and r2 = 0.68 and 0.62, respectively) and Mgex (RPD = 1.72 and 1.49 and r2 = 0.66 and 0.67, respectively). For Caex, very good accuracy was calculated for laboratory method (RPD = 2.19 and r2 = 0.86), as compared to the poor accuracy reported for the on-line method (RPD = 1.30 and r2 = 0.61). The ability of collecting large number of data points per field area (about 12,800 point per 21 ha) and the simultaneous analysis of several soil properties without direct spectral response in the NIR range at relatively high operational speed and appreciable accuracy, encourage the recommendation of the on-line measurement system for site specific fertilisation.

On-line MRI sequences for the evaluation of apple internal quality.

On-line dynamic MRI, which is oriented to industrial grading lines, requires high-speed sequences with motion correction artefacts. In this study two different types of motion correction sequences have been used and have been implemented in real-time (FLASH and UFLARE). They are based on T2* and T2 respectively and their selection depends on the expected contrast effect of the disorder: while watercore enhances bright areas due to higher fluid mobility, internal breakdown potentiates low signal due to texture degradation. For watercore study, five different apple cultivars were used (Normanda-18-, Fuji-35-, Helada-36-, Verde Doncella-54-, Esperiega-75-) along two seasons (2011 and 2012). In total 218 fruits were measured under both, static conditions (20 slices per fruit) and under dynamic conditions (3 repetitions without slice selection). For internal breakdown, Braeburn cultivar has been studied (in total 106 fruits) under both static (20 slices per fruit) and dynamic conditions (3 replicates with slice selection). Metrological aspects such as repeatability of dynamic images and subsequent histogram feature stability become of major interest for further industrial application. Segregation ability among varying degrees of disorder is also analyzed.

Model Based On-Line Energy Prediction System for Semi-Autonomous Mobile Robots

Maximizing energy autonomy is a consistent challenge when deploying mobile robots in ionizing radiation or other hazardous environments. Having a reliable robot system is essential for successful execution of missions and to avoid manual recovery of the robots in environments that are harmful to human beings. For deployment of robots missions at short notice, the ability to know beforehand the energy required for performing the task is essential. This paper presents a on-line method for predicting energy requirements based on the pre-determined power models for a mobile robot. A small mobile robot, Khepera III is used for the experimental study and the results are promising with high prediction accuracy. The applications of the energy prediction models in energy optimization and simulations are also discussed along with examples of significant energy savings.

Tratamiento de imágenes de mineral acarreado post-voladura. Análisis de curvas granulométricas y comparativa mediante sistemasplit on-line y Split desktop: automático y manual

En este proyecto se han analizado distintas imágenes de fragmentos de rocas de distintas granulometrías correspondientes a una serie de voladuras de una misma cantera. Cada una de las voladuras se componen de 20 imágenes. A posteriori utilizando el programa Split Desktop en su versión 3.1, se delimitaron los fragmentos de roca de los que está compuesta la imagen, obteniéndose posteriormente la curva granulométrica correspondiente a dicha imagen. Una vez se calculan las curvas granulométricas correspondientes a cada imagen, se calcula la curva media de todas ellas, pudiéndose considerar por tanto la curva media de cada voladura. Se han utilizado las distintas soluciones del software, manual, online y automático, para realizar los análisis de dichas imágenes y a posteriori comparar sus resultados. Dichos resultados se muestran a través de una serie de gráficos y tablas que se explican con detalle para la comprensión del estudio. De dichos resultados es posible afirmar que, el tratamiento de imágenes realizado de manera online y automático por Split, desemboca en el mismo resultado, al no haber una diferencia estadística significativa. Por el contrario, el sistema manual es diferente de los otros dos, no pudiéndose afirmar cual es mejor de los dos. El manual depende del operario que trabaje las imágenes y el online de los ajustes realizados y por tanto, ambos tienen ciertas incertidumbres difíciles de solucionar. Abstract In this project, different images of rock fragments of different grain sizes corresponding to a series of blasts from the same quarry have been analyzed. To study each blast, 20 images has been used and studied with the software Split Desktop 3.1. Rock fragments from each image has been delimitated with the software, obtaining a grading curve of each one. Once these curves are calculated, the mean curve of these data set is obtained and can be considered the mean curve of each blast. Different software solutions as manual, online and automatic, has been used for the analysis of these images. Then the results has been compared between them. These results are shown through a series of graphs and tables, that are explained in detail, to enhance the understanding of the study. From these results, it can be said that the image processing with online and automatic options from Split, leads to the same result, after an statistical study. On the contrary, the manual Split mode is different from the others; however is not possible to assert what will be the best. The manual Split mode depends on the operator ability and dedication, although the online mode depends on the software settings, so therefore, both have some uncertainties that are difficult to solve.

University Networking in Developing Countries based on C4D-Learning

In recent years, the establishment of cooperation networks between universities is one of the most important trends in higher education all over the world. Well recognized local and international university networks have been implemented in most educational institutions. It is common to find associations of various prestigious universities collaborating in a high-­‐technology research project including a very specialized teaching as well. This is the most common cooperation networks among higher education institutions in developed countries. An increasingly common type of networking between developed and developing universities is related to cooperation for development. This is the case of many universities in Africa that are needed for external help in order to improve its capabilities. Numerous memorandums of understanding regarding first world institutions that collaborate with universities in developing countries describe contributions of eventual visiting professors, teaching material and courses. But probably there exist another type of more important, but less explored association, such as networking among developing universities. The new goal, in this case, is not only the excellence but also the mutual development.

Novel educational assessment for building structures: Automatic evaluation of on-line graphics

This article presents a new automatic evaluation for on-line graphics, its application and the numerous advantages achieved applying this developed correcting method. The software application developed by the Innovation in Education Group “E4”, from the Technical University of Madrid, is oriented for the online self-assessment of the graphic drawings that students carry out as continuous training. The adaptation to the European Higher Educational Area is an important opportunity to research about the possibilities of on-line education assessment. In this way, a new software tool has been developed for continuous self-testing by undergraduates. Using this software it is possible to evaluate the graphical answer of the students. Thus, the drawings made on-line by students are automatically corrected according to the geometry (straight lines, sloping lines or second order curves) and by sizes (depending on the specific values which define the graphics).

Cursos de formación continua on-line de la SEM. Cinco años de actividad.

Se presentan los objetivos y las actividades llevadas a cabo en el área de formación continua on-line de la Sociedad Española de Microbiología (SEM).

New On-Line Excitation-System Ground Fault Location Method Tested in a 106 MVA Synchronous Generator

In this paper, a novel excitation-system ground-fault location method is described and tested in a 106 MVA synchronous machine. In this unit, numerous rotor ground-fault trips took place always about an hour after the synchronization to the network. However, when the field winding insulation was checked after the trips, there was no failure. The data indicated that the faults in the rotor were caused by centrifugal forces and temperature. Unexpectedly, by applying this new method, the failure was located in a cable between the excitation transformer and the automatic voltage regulator. In addition, several intentional ground faults were performed along the field winding with different fault resistance values, in order to test the accuracy of this method to locate defects in rotor windings of large generators. Therefore, this new on-line rotor ground-fault detection algorithm is tested in high-power synchronous generators with satisfactory results.

Creating and modelling personal socio-economic networks in on-line banking

The banking industry is observing how new competitors threaten its millennial business model by targeting unbanked people, offering new financial services to their customer base, and even enabling new channels for existing services and customers. The knowledge on users, their behaviour, and expectations become a key asset in this new context. Well aware of this situation, the Center for Open Middleware, a joint technology center created by Santander Bank and Universidad Politécnica de Madrid, has launched a set of initiatives to allow the experimental analysis and management of socio-economic information. PosdataP2P service is one of them, which seeks to model the economic ties between the holders of university smart cards, leveraging on the social networks the holders are subscribed to. In this paper we describe the design principles guiding the development of the system, its architecture and some implementation details.

Sistema de biorremediación on-line para la eliminación de radionúclidos en aguas radiactivas

En estudios previos desarrollados en la central Nuclear de cofrentes (Valencia) se ha observado que los microorganismos presentes en las aguas radiactivas de las piscinas de almacenamiento de combustible nuclear gastado son capaces de colonizar las superficies metálicas de las paredes y conducciones y formar biopelículas sobre éstas. Estas biopelículas retienen los radionúclidos de las aguas contributyendo a su descontaminación. En este proyecto se ha diseñado una planta piloto para la biodescontaminación de las aguas radiactivas. Actualmente el agua radiactiva procedente de las piscinas de combustible se hace pasar por resinas de intercambio iónico que posteriormente tienen que ser gestionadas como residuos radiactivos. En este proyecto, el agua se hace pasar por un biorreactor que contiene ovillos de acero inoxidable capaces de ser colonizados por los microorganismos existentes en dichas aguas. A su paso por el biorreactor, el agua entra en contacto con el material del ovillo, formándose una biopelícula que retiene los radioisótopos presentes en el agua. La biopelícula es fácilmente eliminada por cualquier procedimiento convencional de descontaminación radioquímica de materiales y los radionúclidos se pueden concentrar en un volumen pequeño de eluyente para su recuperación, disposición final o contención. A continuación, el material del biorreactor puede ser gestionado como material no radiactivo.

Innovación educativa en las redes sociales online: un estudio en la educación superior

Las redes sociales son tan antiguas como las relaciones entre los humanos, ya que las labores de cooperación siempre fueron imprescindibles en los procesos de asociación, tanto los formados por simples células hasta los constituidos por seres vivos. La sociedad está formada por una gran cantidad de situaciones que fomentan dicha colaboración. Desde la creación del Espacio Europeo de Educación Superior se ha promovido la utilización de entornos virtuales de aprendizaje que favorezcan una evaluación más transparente y objetiva. Las redes sociales online son las interfaces digitales más utilizadas por los estudiantes universitarios, por lo que son muchos los expertos que recomiendan analizar la utilidad educativa de este tipo de aplicaciones. Siguiendo estas recomendaciones se implementó una red social online, llamada Formatio, que se utilizó para apoyar el proceso de enseñanza y aprendizaje en la educación superior. El objetivo general de esta tesis doctoral fue valorar el nivel de aceptación de este entorno virtual de aprendizaje para los estudiantes universitarios que participaron en este estudio. Para evaluar el uso de la plataforma se analizaron las actividades generadas por los 172 estudiantes, seleccionados aleatoriamente, matriculados en la asignatura de Estadística y TIC en el curso 2010/2011, del Grado en Ciencias de la Actividad Física y el Deporte. Con el objetivo de estimar la utilidad educativa de las redes sociales online se diseñó y validó el instrumento de Valoración de Recursos Educativos Online (VREO), que fue aplicado a otra muestra aleatoria de 452 estudiantes de la misma facultad durante el curso 2011/2012. Los resultados confirman el éxito de este tipo de espacios virtuales gracias a la alta frecuencia de uso conseguida y a las buenas puntuaciones obtenidas por los alumnos, quienes tienen una buena opinión sobre las ventajas de usar las redes sociales online en la educación superior. De todos los recursos analizados la red social online Formatio ha sido la opción mejor valorada, seguida de Moodle y Facebook en segundo y tercer lugar, y de Twitter y YouTube, en cuarta y en quinta posición. Este estudio establece un punto de partida para futuras investigaciones encaminadas a obtener ciertos indicadores cualitativos y cuantitativos que faciliten una evaluación más justa de los actores integrantes de los sistemas educativos, que ayude a abrir las puertas de nuestra sociedad a la responsabilidad, la eficiencia, la transparencia y la objetividad. ABSTRACT Social networks are as old as human relations, since cooperative work has always been indispensable in all processes of association, from those composed of simple cells to those formed by living beings. Society is shaped by a large amount of situations that stimulate this cooperation. Since the creation of the European Higher Education Area, the use of virtual learning environments that favor more transparent and objective evaluation has been promoted. On-line social networks are the digital interfaces most widely used by university students, which is the reason why many experts recommend an analysis of the educational utility of this type of applications. Following these recommendations, an on-line social network called Formatio was created, which was used in order to support the teaching and learning process in higher education. The general objective of this doctoral dissertation was to evaluate the level of acceptance of this virtual learning environment by the university students who participated in this study. In order to evaluate the use of the platform, the activity created by 172 students chosen at random was analyzed; they were registered in the course on Statistics and Information and Communication Technology of the degree program in Sciences of Physical Activity and Sport during the academic year 2010/2011. With the goal of appraising the educational utility of on-line social networks, a tool for Evaluation of On-line Educational Resources (EOER) was designed, validated, and applied to another random sample of 452 students from the same department during the academic year 2011/2012. The results confirm the success of this type of virtual spaces, thanks to the high frequency of use achieved and the good grades obtained by the students who had a favorable opinion of the advantages of using on-line social networks in higher education. Out of all the resources analyzed, the Formatio on-line social network was the option that received the best evaluation, followed by Moodle and Facebook, which were second and third, and Twitter and YouTube, in fourth and fifth place respectively. This study establishes a starting point for future research that aims to obtain certain qualitative and quantitative indicators that will make it easier to engage in a fairer evaluation of the parties involved in education systems, which will help open the doors of our society to responsibility, efficiency, transparency, and objectivity.

Diseño y evaluación de un procedimiento on-line para la biorremediación de aguas radiactivas en centrales nucleares

Recientemente se ha demostrado la existencia de microorganismos en las piscinas de almacenamiento de combustible nuclear gastado en las centrales nucleares utilizando técnicas convencionales de cultivo en el laboratorio. Estudios posteriores han puesto de manifiesto que los microorganismos presentes eran capaces de colonizar las paredes de acero inoxidable de las piscinas formando biopelículas. Adicionalmente se ha observado la capacidad de estas biopelículas de retener radionúclidos, lo que hace pensar en la posibilidad de utilizarlas en la descontaminación de las aguas radiactivas de las piscinas. En la presente tesis se plantea conocer más profundamente la biodiversidad microbiana de las biopelículas utilizando técnicas de biología molecular como la clonación, además de desarrollar un sistema de descontaminación a escala piloto con el objetivo de valorar si el proceso podría resultar escalable a nivel industrial. Para ello se diseñaron y fabricaron dos biorreactores en acero inoxidable compatibles con las condiciones específicas de seguridad sísmica y protección frente a la radiación en la zona controlada de una central nuclear. Los biorreactores se instalaron en la Central Nuclear de Cofrentes (Valencia) en las proximidades de las piscinas de almacenamiento de combustible nuclear gastado y precediendo a las resinas de intercambio iónico, de forma que reciben el agua de las piscinas permitiendo el análisis in situ de la radiación eliminada del agua de las mismas. Se conectó una lámpara de luz ultravioleta a uno de los biorreactores para poder comparar el desarrollo de bipelículas y la retención de radiactividad en ambas condiciones. En estos biorreactores se introdujeron ovillos de acero inoxidable y de titanio que se extrajeron a diversos tiempos, hasta 635 días para los ovillos de acero inoxidable y hasta 309 días para los ovillos de titanio. Se analizaron las biopelículas desarrolladas sobre los ovillos por microscopía electrónica de barrido y por microscopía de epifluorescencia. Se extrajo el ADN de las biopelículas y, tras su clonación, se identificaron los microorganismos por técnicas independientes de cultivo. Asimismo se determinó por espectrometría gamma la capacidad de las biopelículas para retener radionúclidos. Los microorganismos radiorresistentes identificados pertenecen a los grupos filogenéticos Alpha-proteobacteria, Gamma-proteobacteria, Actinobacteria, Deinococcus-Thermus y Bacteroidetes. Las secuencias de estos microorganismos se han depositado en el GenBank con los números de acceso KR817260-KR817405. Se ha observado una distribución porcentual ligeramente diferente en relación con el tipo de biorreactor. Las biopelículas han retenido fundamentalmente radionúclidos de activación. La suma de Co-60 y Mn-54 ha llegado en ocasiones al 97%. Otros radionúclidos retenidos han sido Cr-51, Co-58, Fe-59, Zn-65 y Zr-95. Se sugiere un mecanismo del proceso de retención de radionúclidos relacionado con el tiempo de formación y desaparición de las biopelículas. Se ha valorado que el proceso escalable puede ser económicamente rentable. ABSTRACT The existence of microorganisms in spent nuclear fuel pools has been demonstrated recently in nuclear power plants by using conventional microbial techniques. Subsequent studies have revealed that those microorganisms were able to colonize the stainless steel pool walls forming biofilms. Additionally, it has been observed the ability of these biofilms to retain radionuclides, which suggests the possibility of using them for radioactive water decontamination purposes. This thesis presents deeper knowledge of microbial biofilms biodiversity by using molecular biology techniques such as cloning, and develops a decontamination system on a pilot scale, in order to assess whether the process could be scalable to an industrial level. Aiming to demonstrate this was feasible, two stainless steel bioreactors were designed and manufactured, both were compatible with seismic and radiation protection standards in the controlled zone of a nuclear plant. These bioreactors were installed in the Cofrentes Nuclear Power Plant (Valencia) next to the spent nuclear fuel pools and preceding (upstream) ion exchange resins. This configuration allowed the bioreactors to receive water directly from the pools allowing in situ analysis of radiation removal. One ultraviolet lamp was connected to one of the bioreactors to compare biofilms development and radioactivity retention in both conditions. Stainless steel and titanium balls were introduced into these bioreactors and were removed after different time periods, up to 635 days for stainless steel balls and up to 309 days for titanium. Biofilms developed on the balls were analyzed by scanning electron microscopy and epifluorescence microscopy. DNA was extracted from the biofilms, was cloned and then the microorganisms were identified by independent culture techniques. Biofilms ability to retain radionuclides was also determined by gamma spectrometry. The identified radioresistant organisms belong to the phylogenetic groups Alphaproteobacteria, Gamma-proteobacteria, Actinobacteria, Deinococcus-Thermus and Bacteroidetes. The sequences of these microorganisms have been deposited in GenBank (access numbers KR817260-KR817405). A different distribution of microorganisms was observed in relation to the type of bioreactor. Biofilms have essentially retained activation radionuclides. Sometimes the sum of Co-60 and Mn-54 reached 97%. Cr-51, Co-58, Fe-59, Zn-65 and Zr-95 have also been retained. A radionuclide retention process mechanism related to biofilms formation and disappearance time is suggested. It has been assessed that the scalable process can be economically profitable.

An approach to automatic learning assessment based on the computational theory of perceptions

E-learning systems output a huge quantity of data on a learning process. However, it takes a lot of specialist human resources to manually process these data and generate an assessment report. Additionally, for formative assessment, the report should state the attainment level of the learning goals defined by the instructor. This paper describes the use of the granular linguistic model of a phenomenon (GLMP) to model the assessment of the learning process and implement the automated generation of an assessment report. GLMP is based on fuzzy logic and the computational theory of perceptions. This technique is useful for implementing complex assessment criteria using inference systems based on linguistic rules. Apart from the grade, the model also generates a detailed natural language progress report on the achieved proficiency level, based exclusively on the objective data gathered from correct and incorrect responses. This is illustrated by applying the model to the assessment of Dijkstra’s algorithm learning using a visual simulation-based graph algorithm learning environment, called GRAPHs