Analysis of the Mechanical Properties of Multicrystalline and Monocrystalline Silicon Wafers Manufactured by Casting Methods

Quasi-monocrystalline silicon wafers have appeared as a critical innovation in the PV industry, joining the most favourable characteristics of the conventional substrates: the higher solar cell efficiencies of monocrystalline Czochralski-Si (Cz-Si) wafers and the lower cost and the full square-shape of the multicrystalline ones. However, the quasi-mono ingot growth can lead to a different defect structure than the typical Cz-Si process. Thus, the properties of the brand-new quasi-mono wafers, from a mechanical point of view, have been for the first time studied, comparing their strength with that of both Cz-Si mono and typical multicrystalline materials. The study has been carried out employing the four line bending test and simulating them by means of FE models. For the analysis, failure stresses were fitted to a three-parameter Weibull distribution. High mechanical strength was found in all the cases. The low quality quasi-mono wafers, interestingly, did not exhibit critical strength values for the PV industry, despite their noticeable density of extended defects.

Revisiting the method to obtain the mechanical properties of hydrided fuel cladding in the hoop direction

The method reported in the literature to calculate the stress–strain curve of nuclear fuel cladding from ring tensile test is revisited in this paper and a new alternative is presented. In the former method, two universal curves are introduced under the assumption of small strain. In this paper it is shown that these curves are not universal, but material-dependent if geometric nonlinearity is taken into account. The new method is valid beyond small strains, takes geometric nonlinearity into consideration and does not need universal curves. The stress–strain curves in the hoop direction are determined by combining numerical calculations with experimental results in a convergent loop. To this end, ring tensile tests were performed in unirradiated hydrogen-charged samples. The agreement among the simulations and the experimental results is excellent for the range of concentrations tested (up to 2000 wppm hydrogen). The calculated stress–strain curves show that the mechanical properties do not depend strongly on the hydrogen concentration, and that no noticeable strain hardening occurs. However, ductility decreases with the hydrogen concentration, especially beyond 500 wppm hydrogen. The fractographic results indicate that as-received samples fail in a ductile fashion, whereas quasicleavage is bserved in the hydrogen-charged samples.

The scaled-time test as an alternative to the pseudo-dynamic test

The stepped and excessively slow execution of pseudo-dynamic tests has been found to be the source of some errors arising from strain-rate effect and stress relaxation. In order to control those errors, a new continuous test method which allows the selection of a more suitable time scale factor in the response is proposed in this work. By dimensional analysis, such scaled-time response is obtained theoretically by augmenting the inertial and damping properties of the structure, for which we propose the use of hydraulic pistons which are servo-controlled to produce active mass and damping, nevertheless using an equipment which is similar to that required in a pseudo-dynamic test. The results of the successful implementation of this technique for a simple specimen are shown here.

Study of the effect of different hole sizes on mechanical strength of wafers for back contact solar cells

Drilling process on wafers to produce EWT or MWT solar cells is a critical fabrication step, which affects on their mechanical stability. The amount of damage introduced during drilling process depends on the density of holes, their size and the chemical process applied afterwards. To quantify the relation between size of the holes and reduction of mechanical strength, several sets of wafers have been prepared, with different hole diameter. The mechanical strength of these sets has been measured by the ring on ring bending test, and the stress state in the moment of failure has been deduced by FE simulation.

Induced shock loads during the separation of the Ariane 5 VEB structure

Tests used to simulate the separation of the lower stage of the Ariane Vehicle Equipment Bay (VEB) were carried out on a flat full scale model. Theoretical studies carried out prior to testing are described. Three different mathematical methods, finite element, component element, and wave propagation, were used. Comparison of the predicted theoretical results with the actual test results is planned.

Study of the Edge and Surface Cracks Influence in the Mechanical Strength of Silicon Wafers

The objective of the present study is the estimation of the depth to which the wire sawing process causes damage to the wafer surfaces. Previous analyses were carried out by means of the four line bending test. The characteristic of this test implied that the failure could be due to surface cracks located in the central zone of the wafer or near the edges. In order to evaluate the influence of the edge or surface cracks a new study has been carried out using the ball/ring on ring test. Description and results of the tests are presented. The preliminary analysis of the failure stress using analytical methods confirms the expected results. A Finite Element model developed to get more information of the test results is also presented.

Análisis de la influencia de los diferentes parámetros de diseño en la aparición de fatiga superficial en contactos mecánicos

La fatiga superficial es uno de los principales problemas en las transmisiones mecánicas y es uno de los focos de atención de las investigaciones de los últimos anos en Tribología. La disminución de viscosidad de los lubricantes para la mejora de la eficiencia, el aumento de las potencias a transmitir, el aumento de la vida de los componentes o la mejora de su fiabilidad han supuesto que los fenómenos de fatiga superficial hayan cobrado especial relevancia, especialmente los fenómenos de pitting y micropitting en cajas multiplicadoras/reductoras de grandes potencias de aplicación, por ejemplo, en el sector eólico. Como todo fenómeno de fatiga, el pitting y micropitting son debidos a la aplicación de cargas ciclicas. Su aparición depende de las presiones y tensiones cortantes en el contacto entre dos superficies que al encontrarse en rodadura y deslizamiento varian con el tiempo. La principal consecuencia de la fatiga superficial es la aparición de hoyuelos de diferente magnitud segun la escala del fenómeno (pitting o micropitting) en la superficie del material. La aparición de estos hoyuelos provoca la perdida de material, induce vibraciones y sobrecargas en el elemento que finalmente acaba fallando. Debido a la influencia de la presión y tensión cortante en el contacto, la aparición de fatiga depende fuertemente del lubricante que se encuentre entre las dos superficies y de las condiciones de funcionamiento en las cuales este trabajando. Cuando el contacto trabaja en condiciones de lubricacion mixta-elastohidrodinamica tiende a aparecer micropitting debido a las altas tensiones localizadas en las proximidades de las asperezas, mientras que si el régimen es de lubricación completa el tipo de fatiga superficial suele ser pitting debido a las tensiones mas suavizadas y menos concentradas. En esta Tesis Doctoral se han analizado todos estos factores de influencia que controlan el pitting y el micropitting prestando especial atención al efecto del lubricante. Para ello, se ha dado un enfoque conjunto a ambos fenómenos resolviendo las ecuaciones involucradas en el contacto elastohidrodinamico no-Newtoniano (la ecuación de Reynolds, la deformación elástica de los sólidos y la reologia del lubricante) para conocer la presión y la tensión cortante en el contacto. Conocidas estas, se resuelve el campo de tensiones en el interior del material y, finalmente, se aplican criterios de fatiga multiaxial (Crossland, Dang Van y Liu-Mahadevan) para conocer si el material falla o no falla. Con la metodología desarrollada se ha analizado el efecto sobre las tensiones y la aparición de la fatiga superficial del coeficiente viscosidad-presion, de la compresibilidad, del espesor especifico de película y de la fricción así como de la influencia de las propiedades a fatiga del material y de las condiciones de funcionamiento (radios de contacto, velocidad, deslizamiento, carga y temperatura). Para la validación de los resultados se han utilizado resultados teóricos y experimentales de otros autores junto con normas internacionales de amplia utilización en el mundo industrial, entre otras, para el diseño y calculo de engranajes. A parte del trabajo realizado por simulación y cálculo de los diferentes modelos desarrollados, se ha realizado un importante trabajo experimental que ha servido no solo para validar la herramienta desarrollada sino que además ha permitido incorporar al estudio factores no considerados en los modelos, como los aditivos del lubricante. Se han realizado ensayos de medida del coeficiente de fricción en una maquina de ensayo puntual con la que se ha validado el cálculo del coeficiente de fricción y se ha desarrollado un proceso de mejora del coeficiente de fricción mediante texturizado superficial en contactos puntuales elastohidrodinamicos mediante fotolitografia y ataque quimico. Junto con los ensayos de medida de fricción en contacto puntual se han realizado ensayos de fricción y fatiga superficial en contacto lineal mediante una maquina de discos que ha permitido evaluar la influencia de diferentes aditivos (modificadores de fricción, antidesgaste y extrema-presion) en la aparición de fatiga superficial (pitting y micropitting) y la fricción en el contacto. Abstract Surface fatigue is one of the most important problems of mechanical transmissions and therefore has been one of the main research topics on Tribology during the last years. On the one hand, industrial demand on fuel economy has led to reduce lubricant viscosity in order to improve efficiency. On the other hand, the requirements of power and life of machine elements are continuously increasing, together with the improvements in reliability. As a consequence, surface fatigue phenomena have become critical in machinery, in particular pitting and micropitting in high power gearboxes of every kind of machines, e.g., wind turbines or cranes. In line with every fatigue phenomena, pitting and micropitting are caused by cyclic loads. Their appearance depends on the evolution of pressures and shear stresses with time, throughout the contact between surfaces under rolling and sliding conditions. The main consequence of surface fatigue is the appearance of pits on the surface. The size of the pits is related to the scale of the fatigue: pitting or micropitting. These pits cause material loss, vibrations and overloads until the final failure is reached. Due to the great influence of the pressures and shear stresses in surface fatigue, the appearance of pits depends directly on the lubricant and the operating conditions. When the contact works under mixed regime (or under elastohydrodynamic but close to mixed regime) the main fatigue failure is micropitting because of the high pressures located near the asperities. In contrast, when the contact works under elastohydrodynamic fully flooded conditions the typical fatigue failure is pitting. In this Ph.D. Thesis, the main factors with influence on pitting and micropitting phenomena are analyzed, with special attention to the effect of the lubricant. For this purpose, pitting and micropitting are studied together by solving the equations involved in the non-Newtonian elastohydrodynamic contact. Thus, pressure and shear stress distributions are found by taking into account Reynolds equation, elastic deflection of the solids and lubricant rheology. Subsequently, the stress field inside the material can be calculated and different multiaxial fatigue criteria (Crossland, Dang Van and Liu- Mahadevan) can be applied to predict whether fatigue failure is reached. The influences of the main parameters on pressure and surface fatigue have been studied, taking into account the lubricant compressibility and its viscosity-pressure coefficient, the specific film thickness, the friction coefficient and the fatigue properties of the contacting materials, together with the operating conditions (contact radius, mean velocity, sliding velocity, load and temperature). Several theoretical and experimental studies of different authors have been used to validate all the results obtained, together with international standards used worldwide in gear design industry. Moreover, an experimental stage has been carried out in order to validate the calculation methods and introduce additional influences not included previously, e.g., lubricant additives. The experimentation includes different friction tests in point contacts performed with a tribological equipment in order to validate the results given by the calculations. Furthermore, the reduction and optimization of the friction coefficient is analyzed by means of textured surfaces, obtained combining photolithography and chemical etching techniques. Besides the friction tests with point contact, friction and surface fatigue tests have also been performed with line contact in a tribological test rig. This equipment is also used to study the influence of different types of additives (friction modifiers, anti-wear and extreme-pressure additives) on surface fatigue (pitting and micropitting).

Análisis de micromovilidad en vástagos femorales mediante ensayo dinámico de oscilaciones libres

La artroplastia de cadera se considera uno de los mayores avances quirúrgicos de la Medicina. La aplicación de esta técnica de Traumatología se ha incrementado notablemente en los últimos anos, a causa principalmente del progresivo incremento de la esperanza de vida. En efecto, con la edad aumentan los problemas de artrosis y osteoporosis, enfermedades típicas de las articulaciones y de los huesos que requieren en muchos casos la sustitución protésica total o parcial de la articulación. El buen comportamiento funcional de una prótesis depende en gran medida de la estabilidad primaria, es decir, el correcto anclaje de la prótesis en el momento de su implantación. Las prótesis no cementadas basan su éxito a largo plazo en la osteointegración que tiene lugar entre el material protésico y el tejido óseo, y para lograrla es imprescindible conseguir unas buenas condiciones de estabilidad primaria. El aflojamiento aséptico es la principal causa de fallo de artroplastia total de cadera. Este es un fenómeno en el que, debido a complejas interacciones de factores mecánicos y biológicos, se producen movimientos relativos que comprometen la funcionalidad del implante. La minimización de los correspondientes danos depende en gran medida de la detección precoz del aflojamiento. Para lograr la detección temprana del aflojamiento aséptico del vástago femoral se han ensayado diferentes técnicas, tanto in vivo como in vitro: análisis numéricos y técnicas experimentales basadas en sensores de movimientos provocados por cargas transmitidas natural o artificialmente, tales como impactos o vibraciones de distintas frecuencias. Los montajes y procedimientos aplicados son heterogéneos y, en muchas ocasiones, complejos y costosos, no existiendo acuerdo sobre una técnica simple y eficaz de aplicación general. Asimismo, en la normativa vigente que regula las condiciones que debe cumplir una prótesis previamente a su comercialización, no hay ningún apartado referido específicamente a la evaluación de la bondad del diseño del vástago femoral con respecto a la estabilidad primaria. El objetivo de esta tesis es desarrollar una metodología para el análisis, in vitro, de la estabilidad de un vástago femoral implantado, a fin de poder evaluar las técnicas de implantación y los diferentes diseños de prótesis previamente a su oferta en el mercado. Además se plantea como requisito fundamental que el método desarrollado sea sencillo, reversible, repetible, no destructivo, con control riguroso de parámetros (condiciones de contorno de cargas y desplazamientos) y con un sistema de registro e interpretación de resultados rápido, fiable y asequible. Como paso previo, se ha realizado un análisis cualitativo del problema de contacto en la interfaz hueso-vástago aplicando una técnica optomecánica del campo continuo (fotoelasticidad). Para ello se han fabricado tres modelos en 2D del conjunto hueso-vástago, simulando tres tipos de contactos en la interfaz: contacto sin adherencia y con holgura, contacto sin adherencia y sin holgura, y contacto con adherencia y homogéneo. Aplicando la misma carga a cada modelo, y empleando la técnica de congelación de tensiones, se han visualizado los correspondientes estados tensionales, siendo estos más severos en el modelo de unión sin adherencia, como cabía esperar. En todo caso, los resultados son ilustrativos de la complejidad del problema de contacto y confirman la conveniencia y necesidad de la vía experimental para el estudio del problema. Seguidamente se ha planteado un ensayo dinámico de oscilaciones libres con instrumentación de sensores resistivos tipo galga extensométrica. Las muestras de ensayo han sido huesos fémur en todas sus posibles variantes: modelos simplificados, hueso sintético normalizado y hueso de cadáver, seco y fresco. Se ha diseñado un sistema de empotramiento del extremo distal de la muestra (fémur) con control riguroso de las condiciones de anclaje. La oscilación libre de la muestra se ha obtenido mediante la liberación instantánea de una carga estética determinada y aplicada previamente, bien con una maquina de ensayo o bien por gravedad. Cada muestra se ha instrumentado con galgas extensométricas convencionales cuya señal se ha registrado con un equipo dinámico comercial. Se ha aplicado un procedimiento de tratamiento de señal para acotar, filtrar y presentar las respuestas de los sensores en el dominio del tiempo y de la frecuencia. La interpretación de resultados es de tipo comparativo: se aplica el ensayo a una muestra de fémur Intacto que se toma de referencia, y a continuación se repite el ensayo sobre la misma muestra con una prótesis implantada; la comparación de resultados permite establecer conclusiones inmediatas sobre los efectos de la implantación de la prótesis. La implantación ha sido realizada por un cirujano traumatólogo utilizando las mismas técnicas e instrumental empleadas en el quirófano durante la práctica clínica real, y se ha trabajado con tres vástagos femorales comerciales. Con los resultados en el dominio del tiempo y de la frecuencia de las distintas aplicaciones se han establecido conclusiones sobre los siguientes aspectos: Viabilidad de los distintos tipos de muestras sintéticas: modelos simplificados y fémur sintético normalizado. Repetibilidad, linealidad y reversibilidad del ensayo. Congruencia de resultados con los valores teóricos deducidos de la teoría de oscilaciones libres de barras. Efectos de la implantación de tallos femorales en la amplitud de las oscilaciones, amortiguamiento y frecuencias de oscilación. Detección de armónicos asociados a la micromovilidad. La metodología se ha demostrado apta para ser incorporada a la normativa de prótesis, es de aplicación universal y abre vías para el análisis de la detección y caracterización de la micromovilidad de una prótesis frente a las cargas de servicio. ABSTRACT Total hip arthroplasty is considered as one of the greatest surgical advances in medicine. The application of this technique on Traumatology has increased significantly in recent years, mainly due to the progressive increase in life expectancy. In fact, advanced age increases osteoarthritis and osteoporosis problems, which are typical diseases of joints and bones, and in many cases require full or partial prosthetic replacement on the joint. Right functional behavior of prosthesis is highly dependent on the primary stability; this means it depends on the correct anchoring of the prosthesis at the time of implantation. Uncemented prosthesis base their long-term success on the quality of osseointegration that takes place between the prosthetic material and bone tissue, and to achieve this good primary stability conditions is mandatory. Aseptic loosening is the main cause of failure in total hip arthroplasty. This is a phenomenon in which relative movements occur, due to complex interactions of mechanical and biological factors, and these micromovements put the implant functionality at risk. To minimize possible damage, it greatly depends on the early detection of loosening. For this purpose, various techniques have been tested both in vivo and in vitro: numerical analysis and experimental techniques based on sensors for movements caused by naturally or artificially transmitted loads, such as impacts or vibrations at different frequencies. The assemblies and methods applied are heterogeneous and, in many cases, they are complex and expensive, with no agreement on the use of a simple and effective technique for general purposes. Likewise, in current regulations for governing the conditions to be fulfilled by the prosthesis before going to market, there is no specific section related to the evaluation of the femoral stem design in relation to primary stability. The aim of this thesis is to develop a in vitro methodology for analyzing the stability of an implanted femoral stem, in order to assess the implantation techniques and the different prosthesis designs prior to its offer in the market. We also propose as a fundamental requirement that the developed testing method should be simple, reversible, repeatable, non-destructive, with close monitoring of parameters (boundary conditions of loads and displacements) and with the availability of a register system to record and interpret results in a fast, reliable and affordable manner. As a preliminary step, we have performed a qualitative analysis of the contact problems in the bone-stem interface, through the application of a continuous field optomechanical technique (photoelasticity). For this proposal three 2D models of bone–stem set, has been built simulating three interface contact types: loosened an unbounded contact, unbounded and fixed contact, and bounded homogeneous contact. By means of applying the same load to each model, and using the stress freezing technique, it has displayed the corresponding stress states, being more severe as expected, in the unbounded union model. In any case, the results clearly show the complexity of the interface contact problem, and they confirm the need for experimental studies about this problem. Afterward a free oscillation dynamic test has been done using resistive strain gauge sensors. Test samples have been femur bones in all possible variants: simplified models, standardized synthetic bone, and dry and cool cadaveric bones. An embedding system at the distal end of the sample with strong control of the anchoring conditions has been designed. The free oscillation of the sample has been obtained by the instantaneous release of a static load, which was previously determined and applied to the sample through a testing machine or using the gravity force. Each sample was equipped with conventional strain gauges whose signal is registered with a marketed dynamic equipment. Then, it has applied a signal processing procedure to delimit, filter and present the time and frequency response signals from the sensors. Results are interpreted by comparing different trials: the test is applied to an intact femur sample which is taken as a reference, and then this test is repeated over the same sample with an implanted prosthesis. From comparison between results, immediate conclusions about the effects of the implantation of the prosthesis can be obtained. It must be said that the implementation has been made by an expert orthopedic surgeon using the same techniques and instruments as those used in clinical surgery. He has worked with three commercial femoral stems. From the results obtained in the time and frequency domains for the different applications the following conclusions have been established: Feasibility of the different types of synthetic samples: simplified models and standardized synthetic femur. Repeatability, linearity and reversibility of the testing method. Consistency of results with theoretical values deduced from the bars free oscillations theory. Effects of introduction of femoral stems in the amplitude, damping and frequencies of oscillations Detection of micromobility associated harmonics. This methodology has been proved suitable to be included in the standardization process of arthroplasty prosthesis, it is universally applicable and it allows establishing new methods for the analysis, detection and characterization of prosthesis micromobility due to functional loads.

Mathematical modelling of pyrotechnic shock in the Ariane 5 VEB structure

The theoretical improvements performed since the last spacecraft and mechanical testing conference on the study of the pyrotechnic shock phenomena produced during the separation of the lower stage of the Ariane 5 Vehicle Equipment Bay (VEB) structure are described. The first theoretical approach used was based on the wave propagation method, including axial and shear waves. The method was changed, in order to capture the bending effects, as well as the influence of the frequency dependent damping values. In addition to the development of the theoretical method, efforts were made to improve the criteria used to model the structure. Comparison of the theoretical predictions with the test results of a flat test sample 1 m width, as well as a preliminary test performed on a small sample, are presented.

Multiscale modeling of a small punch test on nanostructured CP titanium

Small punch (SP) test techniques are typically used to study the mechanical properties of materials or components from miniature size specimens. This kind of test was originally developed to assess ductility loss in steel caused by irradiation or thermal treatment, particularly when the amount of metal was limited, but it soon proved to be a powerful method to estimate several properties.

Influence of proportion and particle size gradation of rubber from end-of-life tires on mechanical, thermal and acoustic properties of plaster-rubber mortars

This work presents the main experimental results obtained from the study of plaster test pieces and boards with addition of various volumetric rubber fractions from mechanical grinding of end-of-life tires (ELTs), in three different particle size gradations. It includes a description of the materials employed, and their proportions. The physical and mechanical properties, as well as the thermal conductivity and acoustic insulation properties are analyzed. Experimental results obtained for specimens with addition of recycled rubber are compared with similar ones, carried out on specimens of plaster of identical features without any addition, evaluating the influence of the particle size and mixture proportions. An improvement in thermal and acoustic performance has been obtained as well as a reduction in density, and as a result, some constructive applications for paving and slabs in rehabilitation works are proposed.

Fracture micromechanisms and mechanical behavior of YBCO bulk superconductors at 77 and 300 K

In this study two YBa2Cu3O7−δ bulk superconductors were evaluated, with the aim of analyzing the influence of the processing method (TSMG and Bridgman) and the test temperature on their mechanical behavior. The relationship between their mechanical properties and fracture micromechanisms has also been studied. Both materials were tested at room and at service temperature. TPB tests were carried out to determine their mechanical behavior, strength and toughness. Moreover, one of the two materials, characterized by transversal microstructural anisotropy, was tested in two directions. Hardness of both materials at nano and micro scale was studied. The results show that the mechanical behavior of the materials is controlled by the defects and cracks that have been introduced during the processing of the materials. A good degree of agreement was found between the experimental crack defects detected by means of SEM and those gathered from the fracture mechanical analysis of the experimental data

Simulating the remote handling of the blanket segments in DEMO fusion reactor with thermo-mechanical meshfree multibody dynamics

The present study shows a first approach to the simulation of the remote handling oper- ation which takes into account the thermal and flexible behavior of the blanket segments and its implications on the remote handling equipment, in order to validate and improve its design.

Induced thermo-mechanical stress in CPV receivers with cycled high intensity light

CPV receivers are made of materials with very different lineal expansion coefficients. Strong variations in DNI due to the passage of clouds can cause sudden temperature changes that creates mechanical stress. For common solder and metal filled polymers the plastic limit could be reached causing substantial fatigue. The best forecast of receiver reliability is therefore achieved by applying an intermittent light source with nominal irradiance level and a number of cycles equal to the expected cloud passages for a given site. The UPM has developed specialized equipment, dubbed the LYSS (Light cYcling Stressing Source), for carrying out such experiments. The small thermal capacity of receivers allows simulating more than 25000 cycles per week. The number of deep transients expected for Madrid in 30 years operation, based on available data, is about 45000. We are currently using the system to cycle a ?Ge/Ag Epoxy/aluminum? receiver, which shows no degradation after 20000 cycles. The equipment can cast up to 200 and 70 W/cm2 on 0.1 and 1 cm2 cells, respectively.

Mechanical behaviour at high temperature of alkali-activated aluminosilicates (geopolymers)

This study was designed to determine the effect of temperature on the mechanical strength (in both in vivo and post-exposure trials) of two alkaline cements (without OPC): (a) 100% fly ash (FA) and (b) 85% FA + 15% bauxite, the activated alkaline solution used was 85% 10-M NaOH + 15% sodium silicate. A Type I 42.5 R Portland cement was used as a control. Two series of trials were conducted: (i) in vivo trials in which bending and compressive strength, fracture toughness and modulus of elasticity were determined at different temperatures; and (ii) post-firing trials, assessing residual bending and compres-sive strength after a 1-h exposure to high temperatures and subsequent cooling. The findings showed that from 25 to 600 C, irrespective of the type of test (in vivo or post-firing), compressive mechanical strength rose, with the specimens exhibiting elastic behaviour and consequently brittle failure. At tem-peratures of over 600 C, behaviour differed depending on the type of test: (i) in the in vivo trials the high temperature induced pseudo-plastic strain and a decline in mechanical strength that did not necessarily entail specimen failure; (ii) in the post-firing trials, compressive strength rose.