Development and characterization of an FK photovoltaic concentrator for maximum conversion efficiency

The outdoor measurements of a single-cell concentrator PV module reaching a regressed 35.6% efficiency and a maximum peak efficiency of 36.0% (both corrected @Tcell=25ºC) are presented. This is the result of the joint effort by LPI and Solar Junction to demonstrate the potential of combining their respective state-of-the-art concentrator optics and solar cells. The LPI concentrator used is an FK, which is an advanced nonimaging concentrator using 4-channel Köhler homogenization, with a primary Fresnel lens and a refractive secondary made of glass. Solar Junction’s cell is a triplejunction solar cell with the A-SLAMTM architecture using dilute-nitrides.

9-fold Fresnel-Köhler concentrator for increased uniform irradiance on high concentrations

Non-uniform irradiance patterns created by Concentrated Photovoltaics (CPV) concentrators over Multi-Junction Cells (MJC) can originate significant power losses, especially when there are different spectral irradiance distributions over the different MJC junctions. This fact has an increased importance considering the recent advances in 4 and 5 junction cells. The spectral irradiance distributions are especially affected with thermal effects on Silicone-on-Glass (SoG) CPV systems. This work presents a new CPV optical design, the 9-fold Fresnel Köhler concentrator, prepared to overcome these effects at high concentrations while maintaining a large acceptance angle, paving the way for a future generation of high efficiency CPV systems of 4 and 5 junction cells.

Broadband active differential array for the mid-frequency SKA band

This paper presents the design and characterization process of an active array demonstrator for the mid-frequency range (i.e., 300 MHz-1000 MHz) of the future Square Kilometre Array (SKA) radio telescope. This demonstrator, called FIDA3 (FG-IGN: Fundación General Instituto Geográfico Nacional - Differential Active Antenna Array), is part of the Spanish contribution for the SKA project. The main advantages provided by this design include the use of a dielectric-free structure, and the use of a fully-differential receiver in which differential low-noise amplifiers (LNAs) are directly connected to the balanced tapered-slot antennas (TSAs). First, the radiating structure and the differential low-noise amplifiers were separately designed and measured, obtaining good results (antenna elements with low voltage standing-wave ratios, array scanning capabilities up to 45°, and noise temperatures better than 52 K with low-noise amplifiers at room temperature). The potential problems due to the differential nature of the proposed solution are discussed, so some effective methods to overcome such limitations are proposed. Second, the complete active antenna array receiving system was assembled, and a 1 m2 active antenna array tile was characterized.

Foreground segmentation in depth imagery using depth and spatial dynamic models for video surveillance applications

Low-cost systems that can obtain a high-quality foreground segmentation almostindependently of the existing illumination conditions for indoor environments are verydesirable, especially for security and surveillance applications. In this paper, a novelforeground segmentation algorithm that uses only a Kinect depth sensor is proposedto satisfy the aforementioned system characteristics. This is achieved by combininga mixture of Gaussians-based background subtraction algorithm with a new Bayesiannetwork that robustly predicts the foreground/background regions between consecutivetime steps. The Bayesian network explicitly exploits the intrinsic characteristics ofthe depth data by means of two dynamic models that estimate the spatial and depthevolution of the foreground/background regions. The most remarkable contribution is thedepth-based dynamic model that predicts the changes in the foreground depth distributionbetween consecutive time steps. This is a key difference with regard to visible imagery,where the color/gray distribution of the foreground is typically assumed to be constant.Experiments carried out on two different depth-based databases demonstrate that theproposed combination of algorithms is able to obtain a more accurate segmentation of theforeground/background than other state-of-the art approaches.

Modal liquid crystal microaxicon array

A novel tunable liquid crystal microaxicon array is proposed and experimentally demonstrated. The proposed structure is capable of generating tunable axicons (thousands of elements) of micrometric size, with simple control (four control voltages) and low voltage, and is totally reconfigurable. Depending on the applied voltages, control over the diameter, as well as the effective wedge angle, can be achieved. Controls over the diameter ranging from 107 to 77 μm have been demonstrated. In addition, a control over the phase profile tunability, from 12π to 24π radians, has been demonstrated. This result modifies the effective cone angle. The diameter tunability, as well the effective cone angle, results in a control over the nondiffractive Bessel beam distance. The RMS wavefront deviation from the ideal axicon is only λ∕3. The proposed device has several advantages over the existing microaxicon arrays, including being simple having a low cost. The device could contribute to developing new applications and to reducing the fabrication costs of current devices.

Four-Band Hamiltonian for fast calculations in intermediate-band solar cells

The 8-dimensional Luttinger–Kohn–Pikus–Bir Hamiltonian matrix may be made up of four 4-dimensional blocks. A 4-band Hamiltonian is presented, obtained from making the non-diagonal blocks zero. The parameters of the new Hamiltonian are adjusted to fit the calculated effective masses and strained QD bandgap with the measured ones. The 4-dimensional Hamiltonian thus obtained agrees well with measured quantum efficiency of a quantum dot intermediate band solar cell and the full absorption spectrum can be calculated in about two hours using Mathematica© and a notebook. This is a hundred times faster than with the commonly-used 8-band Hamiltonian and is considered suitable for helping design engineers in the development of nanostructured solar cells.

Estrategias de desarrollo sostenible de la arquitectura del oasis de M’hamid, desierto del Sahara

Esta investigación se plantea con la hipótesis radical de cómo habitar el desierto de forma sostenible, desde una actitud pragmática y experimental basada en el progreso. La justificación se basa en primer lugar en los 2.000 millones de personas en el mundo que viven en entornos desérticos, el 80% de ellas, en países en desarrollo, porque el 40% de la superficie terrestre está bajo amenaza de desertificación afectando al 37% de la población mundial, con 12 millones de hectáreas al año perdidas por esa causa, y por último, porque se considera el desierto como un entorno de gran atractivo y potencial. El contenido de la investigación se estructura en tres movimientos: posicionamiento, mirada y acción: Desde el posicionamiento se define en primer lugar la sostenibilidad, aportando un nuevo diagrama donde se incorpora el ámbito arquitectónico como uno de los pilares principales, y, posteriormente, se establecen los criterios de evaluación de la sostenibilidad, aportando un sistema de indicadores donde se incorporan parámetros adecuados a las circunstancias del oasis. Del mismo modo, se estudian y analizan metodologías de actuación y proyectos de desarrollo sostenible existentes que enmarcan el estado del arte, constatando la dificultad de adaptación de los mismos a las condiciones de los oasis, por lo que se elabora una metodología propia donde se modifica la dinámica estratégica, de forma que el impulso se plantea desde la acción social, a través de hipótesis de estrategias basadas en sistemas low-cost, autoconstruidas, asumibles económicamente y de implantación factible. El caso de estudio específico radica en la situación extrema de las condiciones en el oasis de M’hamid, donde se evidencia un proceso de desintegración y abandono. Esto es debido a una acumulación de circunstancias externas e internas, de múltiples factores: naturales y antrópicos que afectan al oasis, llevando al extremo las condiciones climáticas y la escasez de recursos, naturales y artificiales. Factores como el cambio climático, la sequía, los cambios en las políticas del agua, la amenaza de desertificación, los conflictos sociales, el desequilibrio ecológico, la escasez económica, la crisis energética, la obsolescencia arquitectónica, el patrimonio construido prácticamente destruido, y la malentendida nueva arquitectura. Es importante constatar la escasa documentación gráfica existente sobre la zona de actuación lo que ha conllevado un amplio trabajo de documentación, tanto cartográfica como de observación directa, aportada a la tesis como investigación de elaboración propia. La mirada analítica al caso de estudio permite conocer los recursos disponibles y las potencialidades latentes del oasis de M’hamid, que permitirán actuar para subvertir la dinámica involutiva imperante, de forma que los dibujos iniciales de apropiación contextual y análisis críticos derivan en mapas de acción diagramados conformados por un sistema de objetos y la definición de estrategias transversales, deconstruyendo el pasado y reconstruyendo el futuro, incorporando sistemas alternativos que se definen en 7 líneas estratégicas de acción formuladas desde los 3 ámbitos relacionados con el ecosistema: ecológico, socio- económico y arquitectónico. Así, la tesis defiende la acción arquitectónica como impulsora del desarrollo sostenible, apoyada en 3 elementos: - la creación de objetos “tecnoartesanos”, para el aprovechamiento de los recursos energéticos - las transformaciones arquitectónicas, para reformular el hábitat desde la eficiencia energética y el progreso - y el impulso de acciones cotidianas, que redefinan las relaciones sociales, creando entornos cooperativos y colaborativos. En el ámbito ecológico se proponen actuaciones anti desertificación mediante incubadoras de árboles; sistemas alternativos de gestión del agua, como la lluvia sólida; estrategias de potenciación de la producción agrícola; la construcción de mecanismos de obtención de energía a partir de residuos, como los paneles solares con botellas PET. En el ámbito socioeconómico se plantean nuevas formas de acción social y de reactivación económica. Por último, en el ámbito urbano-arquitectónico, se incorporan modificaciones morfológicas a la arquitectura existente y una relectura contemporánea de la tierra, como material que permite nuevas geometrías, obteniendo arena petrificada por procesos microbiológicos, y potenciando la tierra como recurso artístico. Esta tesis es un punto de partida, recoge sistemas, estrategias y experiencias, para funcionar como un estímulo o impulso dinamizador del futuro desarrollo sostenible del oasis, abriendo vías de investigación y experimentación. ABSTRACT This research puts forth the radical hypothesis of how to inhabit the desert in a sustainable way, using a pragmatic and experimental approach based on progress. The justification for this resides in the fact that there are 2,000 million people in the world living in desert environments, 80% of them in developing countries. Forty percent of the earth’s surface is under threat of desertification, affecting 37% of the world population and with 12 million hectares being lost each year. And finally, the desert is considered as an attractive environment and therefore, with great potential. The content of the research is structured in three main sections: positioning, observation and action: As a point of departure, sustainability is defined, proposing a new framework where architecture is incorporated as one of the main pillars. Then, the criteria for evaluating sustainability are established. These provide a system of indicators, which incorporate parameters based on the specific circumstances of the oasis. Methodologies and existing sustainable development projects that represent the state-of-the-art are analyzed, discussing the difficulty of adapting them to conditions of oases. A methodology that modifies strategic concepts is developed, whereby the catalyst is social action, and strategies are developed based on low-cost, self-built, and feasible implementation systems. The specific case study lies in the extreme conditions in the oasis of M'hamid, where a process of decay and neglect is evident. This deterioration is due to an accumulation of external and internal circumstances, and of natural and anthropogenic factors that affect the oasis, leading to extreme weather conditions and a shortage of both natural and artificial resources. Factors include; climate change, drought, changes in water policies, the threat of desertification, social conflicts, ecological imbalance, economic shortage, the energy crisis, architectural obsolescence, destruction of built heritage, and misunderstood new architecture. It is important to note the extremely limited graphic information about the area has led me to produce an extensive archive of maps and drawings, many developed by direct observation, that contribute to the research. The case study analysis of the oasis of M'hamid examines the resources available and the latent potential to slow the prevailing trend towards deterioration. The initial drawings of contextual appropriation and critical analysis result in maps and diagrams of action, which are formed by a system of objects and the definition of strategies. These can be thought of as understanding or “deconstructing” the past to reconstruct the future. Alternative approaches defined in seven strategies for action are based on three fields related to the ecosystem: ecological, socioeconomic and architectural. Thus, the thesis defends architectural action to promote sustainable development, based on three elements: - The creation of "techno-artisans", to make use of energy resources - Architectural changes, to reformulate habitat in terms of energy efficiency and progress - And the promotion of everyday actions, to redefine social relations, creating cooperative and collaborative environments. In the ecological field, I propose anti-desertification actions such as; tree incubators, alternative water management systems(such as solid rain),; strategies to empower the agricultural production, energy from low-cost systems made out from recycled materials(such as solar panels from PET bottles or wind turbine from bicycle wheels). In the socioeconomic sphere, I propose to implement new forms of social action and economic regeneration. Finally, within the urban and architectural field, I propose morphological changes to the existing architecture and a contemporary reinterpretation of the earth as a material that allows new geometries, creating petrified sand by microbiological processes or enhancing nature as an artistic and energy resource. This thesis is a starting point. It collects systems, strategies and experiences to serve as a stimulus or dynamic momentum for future sustainable development of the oasis, opening new avenues of research and experimentation. RÉSUMÉ Cette recherche part d'une hypothèse radicale : comment habiter le désert de façon durable, et ce à partir d'une approche pragmatique et expérimentale basée sur le progrès. Cette hypothèse se justifie en raison des 2 milliards de personnes qui dans le monde habitent des environnements désertiques, 80% d'entre eux dans des pays en voie de développement, mais aussi parce que 40% de la surface de la planète est sous menace de désertification, un phénomène affectant 37% de la population mondiale et qui cause la perte de 12 millions d'hectares par an; et enfin parce que le désert est considéré comme un environnement très attrayant et fort d’un grand potentiel. Le contenu de la recherche se divise en trois mouvements: le positionnement, le regard et l'action : Du point de vue du positionnement on définit tout d'abord la durabilité, présentant un nouveau schéma où le domaine de l'architecture devient un des principaux piliers, et, par la suite, des critères d'évaluation de la durabilité sont établis, en fournissant un système d’indicateurs qui intègre les paramètres appropriés aux circonstances de l'oasis. De même, des méthodologies et des projets de développement durable existants sont étudiés et analysés, ce qui encadre l'état de l'art, remarquant la difficulté de les adapter aux conditions des oasis. De cette difficulté découle l'élaboration d'une méthodologie qui modifie la dynamique stratégique, de sorte que l'impulsion provient de l'action sociale, à travers des hypothèses de stratégie basées sur des systèmes low-cost, auto-construits, et de mise en oeuvre économiquement viable. Le cas d'étude spécifique réside en la situation extrême des conditions de l'oasis de M’hamid, où un processus de décadence et de négligence est évident. Cela est dû à une accumulation de circonstances externes et internes, de multiples facteurs: les facteurs naturels et anthropiques qui affectent l'oasis, menant à l'extrême les conditions météorologiques et la pénurie de ressources, autant naturelles qu'artificielles. Des facteurs tels que le changement climatique, la sécheresse, les changements dans les politiques de l'eau, la menace de la désertification, les conflits sociaux, le déséquilibre écologique, la pénurie économique, la crise de l'énergie, l'obsolescence architecturale, le patrimoine bâti pratiquement détruit et une mauvais compréhensif de la nouvelle architecture. Il est important de de faire remarquer le peu d'informations graphiques du domaine d'action, ce qui a conduit à un vaste travail de documentation, autant cartographique que relative à l'observation directe. Cette documentation s'ajoute à la thèse en tant que recherche propre. Le regard analytique sur le cas d'étude permet de connaître les ressources disponibles et le potentiel latent de l'oasis de M’hamid, qui agiront pour renverser la dynamique d'involution en vigueur. Ainsi, les premiers dessins d'appropriation contextuelle et analyse critique deviennent des cartes d'action schématisées formées par un système d'objets et la définition de stratégies transversales, qui déconstruisent le passé et reconstruisent l'avenir, en incorporant des systèmes alternatifs qui se définissent sur 7 lignes stratégiques d'action formulées à partir des 3 domaines en relation avec l’écosystème: l’écologique, le socio-économique et l'architectural. Ainsi, la thèse défend l'action architecturale en tant que promotrice du développement durable, et ce basé sur 3 éléments: - la création d'objets "technoartisans" pour l'exploitation des ressources énergétiques - les modifications architecturales, pour reformuler l'habitat du point de vue de l'efficacité énergétique et le progrès - et la promotion des actions quotidiennes, pour redéfinir les relations sociales, et la création d'environnements de coopération et collaboration. Dans le domaine de l'écologie des actions de lutte contre la désertification sont proposées à travers des pépinières d'arbres, des systèmes alternatifs de gestion de l'eau comme par exemple la pluie solide, des stratégies de mise en valeur de la production agricole, la construction de mécanismes de production d'énergie à partir de résidus, tels que les panneaux solaires ou les bouteilles en PET. Dans le domaine socio-économique, l'on propose de nouvelles formes d'action sociale et de reprise économique. Enfin, dans le domaine de l'urbain et de l'architectural, on incorpore des changements morphologiques à l'architecture existante et une relecture contemporaine de la terre, comme matériau qui permet de nouvelles géométries, en obtenant du sable pétrifié par des procédés microbiologiques et en mettant en valeur la terre comme une ressource artistique. Cette thèse n'est qu'un point de départ. Elle recueille des systèmes, des stratégies et des expériences pour servir de stimulus ou d'impulsion dynamisatrice du futur développement durable de l'oasis, en ouvrant des voies de recherche et d'expérimentation.

Low-power, high-speed FFT processor for MB-OFDM UWB application

This paper presents a low-power, high-speed 4-data-path 128-point mixed-radix (radix-2 & radix-2 2 ) FFT processor for MB-OFDM Ultra-WideBand (UWB) systems. The processor employs the single-path delay feedback (SDF) pipelined structure for the proposed algorithm, it uses substructure-sharing multiplication units and shift-add structure other than traditional complex multipliers. Furthermore, the word lengths are properly chosen, thus the hardware costs and power consumption of the proposed FFT processor are efficiently reduced. The proposed FFT processor is verified and synthesized by using 0.13 µm CMOS technology with a supply voltage of 1.32 V. The implementation results indicate that the proposed 128-point mixed-radix FFT architecture supports a throughput rate of 1Gsample/s with lower power consumption in comparison to existing 128-point FFT architectures

Performance of bare-tether systems under varying magnetic and plasma conditions

Electrodynamic tethered systems, in which an exposed portion of the conducting tether itself collects electrons from the ionosphere, promise to attain currents of 10 A or more in low Earth orbit. For the first time, another desirable feature of such bare-tether systems is reported and analyzed in detail: Collection by a bare tether is relatively insensitive to variations in electron density that are regularly encountered on each revolution of an orbit. This self-adjusting property of bare-tether systems occurs because the electron-collecting area on the tether is not fixed, but extends along its positively biased portion, and because the current varies as collecting length to a power greater than unity. How this adjustment to density variations follows from the basic collection law of thin cylinders is shown. The effect of variations in the motionally induced tether voltage is also analyzed. Both power and thruster modes are considered. The performance of bare-tether systems to tethered systems is compared using passive spherical collectors of fixed area, taking into consideration recent experimental results. Calculations taking into account motional voltage and plasma density around a realistic orbit for bare-tether systems suitable for space station applications are also presented.

Analysis of bare-tether systems for deorbiting low-earth-orbit satellites

Performances, design criteria, and system mass of bare tethers for satellite deorbiting missions are analyzed. Orbital conditions and tether cross section define a tether length, such that 1) shorter tethers are electron collecting practically in their whole extension and 2) longer tethers collect practically the short-circuit current in a fixed segment length. Long tethers have a higher drag efficiency (defined as the drag force vs the tether mass) and are better adapted to adverse plasma densities. Dragging efficiency and mission-related costs are used to define design criteria for tether geometry. A comparative analysis with electric thrusters shows that bare tethers have much lower costs for low- and midinclination orbits and remain an attractive option up to 70 deg.

A low-area reference-free power supply sensor

Power supply unpredictable uctuations jeopardize the functioning of several types of current electronic systems. This work presents a power supply sensor based on a voltage divider followed by buffer-comparator cells employing just MOSFET transistors and provides a digital output. The divider outputs are designed to change more slowly than the thresholds of the comparators, in this way the sensor is able to detect voltage droops. The sensor is implemented in a 65nm technology node occupying an area of 2700?m2 and displaying a power consumption of 50?W. It is designed to work with no voltage reference and with no clock and aiming to obtain a fast response.

Processing of ultra-wideband low-frequency signals, for application in Foliage Penetration (FOPEN) Synthetic Aperture Radar (SAR) systems

Foliage Penetration (FOPEN) radar systems were introduced in 1960, and have been constantly improved by several organizations since that time. The use of Synthetic Aperture Radar (SAR) approaches for this application has important advantages, due to the need for high resolution in two dimensions. The design of this type of systems, however, includes some complications that are not present in standard SAR systems. FOPEN SAR systems need to operate with a low central frequency (VHF or UHF bands) in order to be able to penetrate the foliage. High bandwidth is also required to obtain high resolution. Due to the low central frequency, large integration angles are required during SAR image formation, and therefore the Range Migration Algorithm (RMA) is used. This project thesis identifies the three main complications that arise due to these requirements. First, a high fractional bandwidth makes narrowband propagation models no longer valid. Second, the VHF and UHF bands are used by many communications systems. The transmitted signal spectrum needs to be notched to avoid interfering them. Third, those communications systems cause Radio Frequency Interference (RFI) on the received signal. The thesis carries out a thorough analysis of the three problems, their degrading effects and possible solutions to compensate them. The UWB model is applied to the SAR signal, and the degradation induced by it is derived. The result is tested through simulation of both a single pulse stretch processor and the complete RMA image formation. Both methods show that the degradation is negligible, and therefore the UWB propagation effect does not need compensation. A technique is derived to design a notched transmitted signal. Then, its effect on the SAR image formation is evaluated analytically. It is shown that the stretch processor introduces a processing gain that reduces the degrading effects of the notches. The remaining degrading effect after processing gain is assessed through simulation, and an experimental graph of degradation as a function of percentage of nulled frequencies is obtained. The RFI is characterized and its effect on the SAR processor is derived. Once again, a processing gain is found to be introduced by the receiver. As the RFI power can be much higher than that of the desired signal, an algorithm is proposed to remove the RFI from the received signal before RMA processing. This algorithm is a modification of the Chirp Least Squares Algorithm (CLSA) explained in [4], which adapts it to deramped signals. The algorithm is derived analytically and then its performance is evaluated through simulation, showing that it is effective in removing the RFI and reducing the degradation caused by both RFI and notching. Finally, conclusions are drawn as to the importance of each one of the problems in SAR system design.

Modelling and Control of Stepper Motors for High Accuracy Positioning Systems Used in Radioactive Environments

Hybrid Stepper Motors are widely used in open-loop position applications. They are the choice of actuation for the collimators in the Large Hadron Collider, the largest particle accelerator at CERN. In this case the positioning requirements and the highly radioactive operating environment are unique. The latter forces both the use of long cables to connect the motors to the drives which act as transmission lines and also prevents the use of standard position sensors. However, reliable and precise operation of the collimators is critical for the machine, requiring the prevention of step loss in the motors and maintenance to be foreseen in case of mechanical degradation. In order to make the above possible, an approach is proposed for the application of an Extended Kalman Filter to a sensorless stepper motor drive, when the motor is separated from its drive by long cables. When the long cables and high frequency pulse width modulated control voltage signals are used together, the electrical signals difer greatly between the motor and drive-side of the cable. Since in the considered case only drive-side data is available, it is therefore necessary to estimate the motor-side signals. Modelling the entire cable and motor system in an Extended Kalman Filter is too computationally intensive for standard embedded real-time platforms. It is, in consequence, proposed to divide the problem into an Extended Kalman Filter, based only on the motor model, and separated motor-side signal estimators, the combination of which is less demanding computationally. The efectiveness of this approach is shown in simulation. Then its validity is experimentally demonstrated via implementation in a DSP based drive. A testbench to test its performance when driving an axis of a Large Hadron Collider collimator is presented along with the results achieved. It is shown that the proposed method is capable of achieving position and load torque estimates which allow step loss to be detected and mechanical degradation to be evaluated without the need for physical sensors. These estimation algorithms often require a precise model of the motor, but the standard electrical model used for hybrid stepper motors is limited when currents, which are high enough to produce saturation of the magnetic circuit, are present. New model extensions are proposed in order to have a more precise model of the motor independently of the current level, whilst maintaining a low computational cost. It is shown that a significant improvement in the model It is achieved with these extensions, and their computational performance is compared to study the cost of model improvement versus computation cost. The applicability of the proposed model extensions is demonstrated via their use in an Extended Kalman Filter running in real-time for closed-loop current control and mechanical state estimation. An additional problem arises from the use of stepper motors. The mechanics of the collimators can wear due to the abrupt motion and torque profiles that are applied by them when used in the standard way, i.e. stepping in open-loop. Closed-loop position control, more specifically Field Oriented Control, would allow smoother profiles, more respectful to the mechanics, to be applied but requires position feedback. As mentioned already, the use of sensors in radioactive environments is very limited for reliability reasons. Sensorless control is a known option but when the speed is very low or zero, as is the case most of the time for the motors used in the LHC collimator, the loss of observability prevents its use. In order to allow the use of position sensors without reducing the long term reliability of the whole system, the possibility to switch from closed to open loop is proposed and validated, allowing the use of closed-loop control when the position sensors function correctly and open-loop when there is a sensor failure. A different approach to deal with the switched drive working with long cables is also presented. Switched mode stepper motor drives tend to have poor performance or even fail completely when the motor is fed through a long cable due to the high oscillations in the drive-side current. The design of a stepper motor output fillter which solves this problem is thus proposed. A two stage filter, one devoted to dealing with the diferential mode and the other with the common mode, is designed and validated experimentally. With this ?lter the drive performance is greatly improved, achieving a positioning repeatability even better than with the drive working without a long cable, the radiated emissions are reduced and the overvoltages at the motor terminals are eliminated.

Implications of low breakdown voltage of component subcells on external quantum efficiency measurements of multijunction solar cells

The electrical and optical coupling between subcells in a multijunction solar cell affects its external quantum efficiency (EQE) measurement. In this study, we show how a low breakdown voltage of a component subcell impacts the EQE determination of a multijunction solar cell and demands the use of a finely adjusted external voltage bias. The optimum voltage bias for the EQE measurement of a Ge subcell in two different GaInP/GaInAs/Ge triple-junction solar cells is determined both by sweeping the external voltage bias and by tracing the I–V curve under the same light bias conditions applied during the EQE measurement. It is shown that the I–V curve gives rapid and valuable information about the adequate light and voltage bias needed, and also helps to detect problems associated with non-ideal I–V curves that might affect the EQE measurement. The results also show that, if a non-optimum voltage bias is applied, a measurement artifact can result. Only when the problems associated with a non-ideal I–V curve and/or a low breakdown voltage have been discarded, the measurement artifacts, if any, can be attributed to other effects such as luminescent coupling between subcells.