Factores nutricionales que influyen sobre las variables productivas y el desarrollo del tracto gastrointestinal en pollitas comerciales rubias = Nutritional factors affecting productive performance and gastrointestinal tract traits in commercial brown-egg laying pullets

El objetivo general de esta Tesis doctoral fue estudiar la influencia de diversos factores nutricionales sobre los parámetros productivos y el desarrollo del tracto digestivo de pollitas rubias destinadas a la producción de huevos comerciales. Para alcanzar este objetivo se realizaron tres experimentos donde se estudió el cereal principal, el tamaño de partícula del cereal y el nivel de energía y la presentación de los piensos. En el experimento 1 se estudió la influencia del cereal (piensos con enzimas) y la presentación del pienso sobre los parámetros productivos y las características del tracto digestivo en 576 pollitas rubias de 1 a 120 d de edad. De 1 a 45 d de la edad, se utilizaron 4 piensos experimentales organizados de forma factorial con 2 cereales al 50% de inclusión (maíz vs. trigo) y 2 presentaciones del pienso (harina vs. gránulo de 2- mm de diámetro). Cada tratamiento se replicó 6 veces (24 pollitas por réplica). De 46 a 120 d de edad todas las dietas (maíz o trigo) se ofrecieron en harina y por tanto, la única diferencia entre tratamientos fue el cereal utilizado. De 1 a 120 d de edad, las pollitas que recibieron los piensos basados en maíz tuvieron una ganancia de peso vivo (PV) superior (P < 0,05) que las que recibieron los piensos basados en trigo, pero el índice de conversión (IC) fue similar para ambos grupos. De 1 a 45 d de edad, las pollitas alimentadas con gránulo consumieron más pienso (P < 0,001) y tuvieron una ganancia de peso superior (P < 0,001) que las pollitas alimentadas con harina. Gran parte de los efectos beneficiosos de la granulación sobre los parámetros productivos se mantuvieron al final de la prueba (120 d de edad). A los 45 d de edad, el peso relativo de la molleja (PR; g/kg PV) fue superior (P < 0,01) en pollitas alimentadas con maíz que en pollitas alimentadas con trigo. La alimentación en gránulo redujo el PR del tracto gastro intestinal (TGI) y de la molleja (P < 0,001), así como la longitud relativa (LR; cm/kg PV) del intestino delgado (P< 0.01) a ambas edades (45 y 120 d de edad). El tipo de cereal utilizado no afectó al pH del contenido de la molleja a 120 d de edad pero fué inferior (P < 0,01) en las pollitas que recibieron el pienso en harina de 1 a 45 d de la edad que en las que recibieron el pienso en gránulo. Se concluye que el trigo puede substituir al maíz en piensos para pollitas si se acepta una ligera reducción en la ganancia de peso. Asímismo, la alimentación en gránulo de 1 a 45 d de edad aumentó la ganancia de peso a esta edad y al final de la prueba, así como el pH de la molleja a 120 d de edad. La presentación del pienso en gránulo redujo el PR de la molleja y la LR del TGI a 120 d de edad. En el experimento 2 se utilizaron un total de 864 pollitas rubias Hy-Line de 1 d de edad para estudiar la influencia del cereal de la dieta (500 g de maíz o trigo/kg) y el tamaño de partícula del mismo (molienda con molino de martillos con un diámetro de criba de 6, 8, o 10-mm) sobre los parámetros productivos y las características del TGI de 1 a 120 d de edad. Cada uno de los 6 tratamientos se replicó 6 veces (24 pollitas por réplica). De 1 a 45 d de edad, la ganancia de PV aumentó (P< 0,001) y el IC se mejoró (P < 0,05) al reducir el tamaño de partícula del cereal, pero no se observaron diferencias en el periodo crecimiento de 45 a 120 d de edad. A los 45 d de vida, las pollitas alimentadas con maíz tendieron (P < 0,10) a tener un mayor PR del TGI y del proventrículo y una mayor LR del intestino delgado que las pollitas alimentadas con trigo. Asímismo, el PR del TGI a esta edad, aumentó (P < 0,05) a medida que aumentaba el tamaño de partícula del cereal utilizado. A los 120 d de edad, el tratamiento no afectó el PR de ninguno de los órganos del TGI ni al pH de la molleja. Sin embargo, la LR del intestino delgado fue superior (P < 0,05) para las pollitas alimentadas con trigo que para las pollitas alimentadas con maíz. La LR del TGI se redujó (P < 0,05) al aumentar el tamaño de partícula del cereal. Se concluye que el trigo puede incluirse 500 g/kg en piensos de pollitas de 1 a 120 días de edad y que el tamaño de partícula de los cereales afecta el crecimiento de las pollitas durante los primeros 45 d de vida, pero no después. Por lo tanto, se recomienda moler el cereal utilizado al inicio del período de recría (1 a 45 d de edad) con una criba de diámetro igual o inferior a 8 mm. En el experimento 3 se utilizaron un total de 1.152 pollitas rubias Hy-Line de 1 d de edad para estudiar la influencia del nivel de energía de la dieta y la presentación del pienso sobre la productividad y las características del TGI. De 1 a 45 d de edad se utilizaron 6 piensos organizados de forma factorial con 3 concentraciones energéticas (baja: 11,44 MJ; media: 12,05 MJ y alta: 12,66 MJ/kg) y 2 presentaciones del pienso (harina vs. gránulo). De 45 a 120 d todos los piensos experimentales se suministraron en forma de harina y por tanto, la única diferencia entre tratamientos fue el nivel de EMAn utilizado. Cada uno de los 6 tratamientos se replicó 8 veces y la unidad experimental fue la jaula con 24 pollitas. De 1 a 120 d de edad, la ganancia de PV y el IC mejoraron a medida que aumentó la EMAn del pienso (P < 0,001). Las pollitas alimentadas con gránulo de 1 a 45 d de edad comieron mas y tuvieron una ganancia de peso superior (P < 0,001) que las alimentadas con harina. En el global de la prueba, la ganancia de PV fue mayor (P < 0,01) para las pollitas alimentadas con piensos en gránulo. A los 45 d de edad, el PR de todos los segmentos del TGI estudiados fue inferior para las pollitas alimentadas con piensos de alta energía que para las pollitas alimentadas con piensos de media o baja energía. A 120 d de edad, el PR de la molleja fue superior (P < 0,01) para las pollitas alimentadas con piensos de baja energía que con los otros piensos. Sin embargo, la LR del TGI no se vió afectada por el nivel de energía de los piensos. A los 45 d de edad, la alimentación con gránulo redujo el PR del proventrículo (P < 0,05), de la molleja (P < 0,001) y del TGI (P < 0.001), así como la LR del intestino delgado (P < 0,05) y de los ciegos (P < 0,001). A pesar de que las pollitas solo recibieron los piensos en gránulo durante los primeros 45 d de vida, la alimentación con gránulos redujo el PR de la molleja y del proventrículo a 120 d de edad. Se concluye que la alimentación con gránulos durante los primeros 45 d de vida mejora el consumo de pienso y el PV de las pollitas a 120 d de edad. Un aumento del nivel de energía de la dieta de 12,0 a 12,7 MJ/kg mejora los parámetros productivos de 1 a 120 d de edad pero reduce el tamaño del proventrículo y de la molleja. En base de estos resultados concluimos que maíz y trigo con enzimas pueden utilizarse indistintamente en piensos para pollitas de 1 a 120 d de edad con sólo una ligera disminución del PV final con trigo. La granulación y la reducción del tamaño de partícula del cereal del pienso de primera edad (1 a 45 d de vida) y el uso de piensos de alta densidad energética, mejoran los PV a 120 d de edad. Por lo tanto, es recomendable moler los cereales con cribas de no más de 8-mm de diámetro. También, la granulación del pienso y el uso de piensos de alta energía (pobres en fibra bruta) pueden reducir el desarrollo del TGI especialmente de la molleja, lo que puede perjudicar el consumo posterior de pienso durante el inicio del ciclo de puesta. ABSTRACT The general objective of this Thesis was to study the effect of different nutritional factors on productive performance and the development of the gastrointestinal tract (GIT) of commercial brown egg-laying pullets from 1 to 120 d of age. In this respect, the influence of type and particle size of the cereal, and feed form, and energy content of the die,t were studied in 3 experiments. In experiment 1, the influence of the main cereal and feed form of the diet on performance and GIT traits was studied in 576 brown-egg laying pullets from 1 to 120 d of age. From 1 to 45 d of age, 4 diets arranged factorially with 2 cereals (maize vs. wheat) and 2 feed forms (mash vs. pellets) were used. Each treatment was replicated 6 times (24 pullets per replicate). From 46 to 120 d of age, all diets were offered in mash form and therefore, the only difference among diets was the cereal used. Cumulatively, pullets fed the maize diets had higher body weight (BW) gain (P< 0.05) but similar feed conversion ratio (FCR) than pullets fed the wheat diets. From 1 to 45 d of age, pullets fed pellets consumed more feed (P < 0.001) and had higher BW gain (P < 0.001) than pullets fed mash. Most of the beneficial effects of pelleting on productive performance of the birds were still evident at 120 d of age. At 45 d of age, gizzard relative weight (RW; g/kg BW) was higher (P < 0.01) in pullets fed maize than in pullets fed wheat. Feeding pellets reduced the RW of the GIT and the gizzard (P < 0.001) as well as the relative length (RL; cm/kg BW) of the small intestine (SI, P < 0.01) at both ages. The pH of the gizzard contents at 120 d of age was not affected by the main cereal of the diet, but was lower in pullets fed mash from 1 to 45 d of age (P < 0.01) than in pullets fed pellets. We conclude that wheat supplemented with enzymes can be used in substitution of maize in pullet diets with only a slight reduction in BW gain at 120 d of age. Also, feeding pellets from 1 to 45 d of age increased BW gain and pH of the gizzard, and reduced the RW of the gizzard and the RL of the GIT at 120 d of age. In experiment 2, a total of 864 brown-egg laying pullets was used to study the effects of the main cereal of the diet (500 g maize or wheat/kg) and particle size of the cereal (hammer milled to pass through a 6, 8, and 10-mm screen) on growth performance and GIT traits from 1 to 120 d of age. Each of the 6 treatments was replicated 6 times (24 pullets per replicate). Type of cereal did not affect pullet performance at any age. From 1 to 45 d of age, BW gain was increased (P < 0.001) and FCR was improved (P < 0.05) as the particle size of the cereal was reduced, but no effects were observed after this age. At 45 d of age, pullets fed maize tended (P < 0.10) to have a heavier RW of the GIT and proventriculus and a higher relative length (RL, cm/kg BW) of the SI than pullets fed wheat. Also at this age, the RW of the GIT increased (P < 0.05) with increases in particle size of the cereal. At 120 d of age, dietary treatment did not affect the RW of any of the organs studied or gizzard pH, but the RL of the SI was higher (P < 0.05) for pullets fed wheat than for pullets fed maize. Also, the RL of the SI was reduced (P < 0.05) as the particle size of the cereal increased. We conclude that 500 g wheat/kg can be included in pullet feeds from 1 to 120 d of age, and that particle size of the cereal affects pullet performance during the first 45 d of life but not thereafter. Therefore, it is recommended to grind the cereal used in this period with a screen size of no more than 8-mm. In experiment 3, a total of 1,152 one-day-old Hy-Line Brown egg laying pullets were used to study the influence of the energy content of the diet and feed form on productive performance and on several GIT traits. From 1 to 45 d of age, there were 6 diets arranged factorially with 3 concentrations of AMEn (low: 11.66 MJ/kg, medium: 12.05 MJ/kg and high: 12.66 MJ/kg) of the diet and 2 feed forms (mash vs. pellets). From 45 to 120 d all diets were fed in mash form and therefore, the only difference among treatments in this period was the energy content of the diets. Each of the 6 treatments was replicated 8 times and the experimental unit was formed by 24 pullets. Cumulatively, BW gain and FCR improved as the AMEn of the diet increased (P < 0.001). Also, pullets fed pellets from 1 to 45 d of age had higher feed intake and BW gain (P < 0.001) in this period and higher cumulative BW gain (P < 0.01) than pullets fed mash. At 45 d of age, the RWof all the segments of the GIT was lower for pullets fed the high- than for pullets fed the medium- or low- energy diets. At 120 d of age, the RW of the gizzard was higher (P < 0.01) for pullets fed the low energy diets than for pullets fed the other diets. However, the RL of the GIT was not affected by the energy content of the diet. Feeding pellets reduced the RW of the proventriculus (P < 0.05), gizzard (P < 0.001), and GIT (P < 0.001), as well as the RL of the small intestine (P < 0.05) and the ceaca (P < 0.001) at 45 d of age. The effects of feeding pellets on RW of gizzard and proventriculus were still evident at 120 d of age. We concluded that feeding pellets from 1 to 45 d of age improved feed intake and BW of pullets at 120 d of age and that an increase in the energy content of the diet increased pullet performance at all ages but reduced the RW of the proventriculus and gizzard. We conclude that maize and wheat can be used indistinctly in diets for egg laying pullets from 1 to 120 d of age, with only a slight reduction in final BW when wheat is used. Also, particle size of the cereal affects pullet performance during the first 45 d of life but not thereafter. Pelleting of the feeds, and grinding the cereal with a screen size of no more than 8-mm from 1 to 45 d of age, and the use of high density energy diets are recommended in order to achieve adequate target BW at 120 d of age. However, pelleting of the feed, very fine grinding, and the use of high AMEn diets might hinder the development of the GIT, especially that of the gizzard, which might affect feed intake of laying hens especially at the beginning of the production cycle.

A multi-resource load balancing algorithm for cloud cache systems

With the advent of cloud computing model, distributed caches have become the cornerstone for building scalable applications. Popular systems like Facebook [1] or Twitter use Memcached [5], a highly scalable distributed object cache, to speed up applications by avoiding database accesses. Distributed object caches assign objects to cache instances based on a hashing function, and objects are not moved from a cache instance to another unless more instances are added to the cache and objects are redistributed. This may lead to situations where some cache instances are overloaded when some of the objects they store are frequently accessed, while other cache instances are less frequently used. In this paper we propose a multi-resource load balancing algorithm for distributed cache systems. The algorithm aims at balancing both CPU and Memory resources among cache instances by redistributing stored data. Considering the possible conflict of balancing multiple resources at the same time, we give CPU and Memory resources weighted priorities based on the runtime load distributions. A scarcer resource is given a higher weight than a less scarce resource when load balancing. The system imbalance degree is evaluated based on monitoring information, and the utility load of a node, a unit for resource consumption. Besides, since continuous rebalance of the system may affect the QoS of applications utilizing the cache system, our data selection policy ensures that each data migration minimizes the system imbalance degree and hence, the total reconfiguration cost can be minimized. An extensive simulation is conducted to compare our policy with other policies. Our policy shows a significant improvement in time efficiency and decrease in reconfiguration cost.

Design of a twin capacitive load and its application to the outdoor rating of photovoltaic modules

This paper describes the design of an original twin capacitive load that is able of tracing simultaneously the I?V characteristics of two photovoltaic modules. Besides, an example of the application of this dual system to the outdoor rating of photovoltaic modules is presented, whose results have shown a good degree of repeatability.

Space-state robust control of a Buck converter with amorphous core coil and variable load

Pulse-width modulation is widely used to control electronic converters. One of the most frequently used topologies for high DC voltage/low DC voltage conversion is the Buck converter. These converters are described by a second order system with an LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core rather than an air core permits the design of smaller converters. If high switching frequencies are used to obtain high quality voltage output, then the value of the auto inductance L is reduced over time. Robust controllers are thus needed if the accuracy of the converter response must be preserved under auto inductance and payload variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a switching frequency that is not too high is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results and a comparison with a standard PID controller are also presented.

3-Phase Rectifier System with very demanding dynamic load: Architecture analysis and control strategy

A distributed power architecture for aerospace application with very restrictive specifications is analyzed. Parameters as volume, weight and losses are analyzed for the considered power architectures. In order to protect the 3 phase generator against high load steps, an intermediate bus (based in a high capacitance) to provide energy to the loads during the high load steps is included. Prototypes of the selected architecture for the rectifier and EMI filter are built and the energy control is validated.

Influence of main cereal and mean particle size of the diet on productive performance and egg quality of brown-laying hens

Influencia de cereal principal y el tamaño medio de partícula de la dieta sobre el desempeño productivo y calidad de los huevos de las gallinas marrones para puesta.

A review of load models for the prediction of footfall-induced vibration in structures

Crowd induced dynamic loading in large structures, such as gymnasiums or stadium, is usually modelled as a series of harmonic loads which are defined in terms of their Fourier coefficients. Different values of these coefficients that were obtained from full scale measurements can be found in codes. Recently, an alternative has been proposed, based on random generation of load time histories that take into account phase lag among individuals inside the crowd. This paper presents the testing done on a structure designed to be a gymnasium. Two series of dynamic test were performed on the gym slab. For the first test an electrodynamic shaker was placed at several locations and during the second one people located inside a marked area bounced and jumped guided by different metronome rates. A finite element model (FEM) is presented and a comparison of numerically predicted and experimentally observed vibration modes and frequencies has been used to assess its validity. The second group of measurements will be compared with predictions made using the FEM model and three alternatives for crowd induced load modelling.

On the layout of a least weight single span structure with uniform load. Some comments and improvements

Beghini et al (Struct Multidisc Optim doi:10.1007/s00158-013-1030-6, 2013) have published a very interesting paper arriving to practically the same nearly optimal solutions for the so named “bridge prob- lem” that the Writers published a year before, but using an alternative and remarkable approach to the problem. In spite of this general agreement, the Writers think that some details of the paper can be improved and there are results that can be given a clear and mean- ingful interpretation thanks to an old and practically unknown theorem on optimal slenderness.

Discrete element analysis for the assessment of the accuracy of load cell-based dynamic weighing systems in grape harvesters under different ground conditions

Dynamic weighing systems based on load cells are commonly used to estimate crop yields in the field. There is lack of data, however, regarding the accuracy of such weighing systems mounted on harvesting machinery, especially on that used to collect high value crops such as fruits and vegetables. Certainly, dynamic weighing systems mounted on the bins of grape harvesters are affected by the displacement of the load inside the bin when moving over terrain of changing topography. In this work, the load that would be registered in a grape harvester bin by a dynamic weighing system based on the use of a load cell was inferred by using the discrete element method (DEM). DEM is a numerical technique capable of accurately describing the behaviour of granular materials under dynamic situations and it has been proven to provide successful predictions in many different scenarios. In this work, different DEM models of a grape harvester bin were developed contemplating different influencing factors. Results obtained from these models were used to infer the output given by the load cell of a real bin. The mass detected by the load cell when the bin was inclined depended strongly on the distribution of the load within the bin, but was underestimated in all scenarios. The distribution of the load was found to be dependent on the inclination of the bin caused by the topography of the terrain, but also by the history of inclination (inclination rate, presence of static periods, etc.) since the effect of the inertia of the particles (i.e., representing the grapes) was not negligible. Some recommendations are given to try to improve the accuracy of crop load measurement in the field.

Type of grinding of the main cereal of the diet affects production of brown egg-laying hens

The influence of method of grinding of the cereal of the diet on production and egg quality was studied in 420 Hy-line brown egg-laying hens. The design was completely randomized with six treatments arranged as a 3 × 2 factorial with three cereals (barley, dented maize and soft wheat) and two grinding procedures (hammer mill vs. roller mill). Each treatment was replicated seven times and the experimental unit was an enriched cage with ten hens. Production was recorded every four weeks from 24 to 59 weeks of age and egg quality was measured at 40 and 56 weeks of age. For the entire experiment, feed intake was higher in hens fed wheat or maize than in hens fed barley (110.8 and 110.7 vs. 109.7 g/d; P = 0.014) but most of the differences were observed when the cereal was roller milled (P = 0.009 for the interaction). Also, egg production was similar for the three diets when the cereal was hammer milled but tended to be lower for the barley than for the wheat or maize diets when the cereal was roller milled (P = 0.09 for the interaction). None of the other productive or egg quality traits was affected by dietary treatment. We conclude that roller mills are useful to grind low fiber cereals, such as maize or wheat. However, the use of the roller mill might not be adequate when barley is the main cereal in diets for egg-laying hens.

Limit load instabilities in structural elements

Este trabajo analiza distintas inestabilidades en estructuras formadas por distintos materiales. En particular, se capturan y se modelan las inestabilidades usando el método de Riks. Inicialmente, se analiza la bifurcación en depósitos cilíndricos formados por material anisótropo sometidos a carga axial y presión interna. El análisis de bifurcación y post-bifurcación asociados con cilindros de pared gruesa se formula para un material incompresible reforzado con dos fibras que son mecánicamente equivalentes y están dispuestas simétricamente. Consideramos dos casos en la naturaleza de la anisotropía: (i) Fibras refuerzo que tienen una influencia particular sobre la respuesta a cortante del material y (ii) Fibras refuerzo que influyen sólo si la fibra cambia de longitud con la deformación. Se analiza la propagación de las inestabilidades. En concreto, se diferencia en el abultamiento (bulging) entre la propagación axial y la propagación radial de la inestabilidad. Distintos modelos sufren una u otra propagación. Por último, distintas inestabilidades asociadas al mecanismo de ablandamiento del material (material softening) en contraposición al de endurecimiento (hardening) en una estructura (viga) de a: hormigón y b: hormigón reforzado son modeladas utilizando una metodología paralela a la desarrollada en el análisis de inestabilidades en tubos sometidos a presión interna. This present work deals with the instability of structures made of various materials. It captures and models different types of instabilities using numerical analysis. Firstly, we consider bifurcation for anisotropic cylindrical shells subject to axial loading and internal pressure. Analysis of bifurcation and post bifurcation of inflated hyperelastic thick-walled cylinder is formulated using a numerical procedure based on the modified Riks method for an incompressible material with two preferred directions which are mechanically equivalent and are symmetrically disposed. Secondly, bulging/necking motion in doubly fiber-reinforced incompressible nonlinearly elastic cylindrical shells is captured and we consider two cases for the nature of the anisotropy: (i) reinforcing models that have a particular influence on the shear response of the material and (ii) reinforcing models that depend only on the stretch in the fiber direction. The different instability motions are considered. Axial propagation of the bulging instability mode in thin-walled cylinders under inflation is analyzed. We present the analytical solution for this particular motion as well as for radial expansion during bulging evolution. For illustration, cylinders that are made of either isotropic incompressible non-linearly elastic materials or doubly fiber reinforced incompressible non-linearly elastic materials are considered. Finally, strain-softening constitutive models are considered to analyze two concrete structures: a reinforced concrete beam and an unreinforced notch beam. The bifurcation point is captured using the Riks method used previously to analyze bifurcation of a pressurized cylinder.

Contribution to Load-Frequency Regulation of a Hydropower Plant with Long Tail-Race Tunnel

In this paper, a hydroelectric power plant with long tail-race tunnel has been modelled for assessing its contribution to secondary regulation reserve. Cavitation problems, caused by the discharge conduit length, are expected downstream the turbine where low pressure appears during regulation manoeuvres. Therefore, governor's gains should be selected taking into account these phenomena. On the other hand, regulation services bidden by the plant operator should fulfil TSO (Transmission System Operator) quality requirements. A methodology for tuning governor PI gains is proposed and applied to a Hydro power plant in pre-design phase in northwest area of Spain. The PI gains adjustment proposed provides a proper plant response, according to some established indexes, while avoiding cavitation phenomena.

Transversal load distribution on bridge decks

An orthotropic rectangular plate is analysed. The plate has been considered simply supported in two opposite edges and general boundary conditions along the remainder edges. Matrix formulation, very convenient for programming on a digital computer, is used through the text. This technique is applied to an actual bridge deck and the results are compared with those obtained by means of the Guyon-Massonet-Rowe method

Productive performance of brown-egg laying pullets from hatching to 5 weeks of age as affected by fiber inclusion, feed form, and energy concentration of the diet

The effects of fiber inclusion, feed form, and energy concentration of the diet on the growth performance of pullets from hatching to 5 wk age were studied in 2 experiments. In Experiment 1, there was a control diet based on cereals and soybean meal, and 6 extra diets that included 2 or 4% of cereal straw, sugar beet pulp (SBP), or sunflower hulls (SFHs) at the expense (wt/wt) of the whole control diet. From hatching to 5 wk age fiber inclusion increased (P < 0.05) ADG and ADFI, and improved (P < 0.05) energy efficiency (EnE; kcal AMEn/g ADG), but body weight (BW) uniformity was not affected. Pullets fed SFH tended to have higher ADG than pullets fed SBP (P = 0.072) with pullets fed straw being intermediate. The feed conversion ratio (FCR) was better (P < 0.05) with 2% than with 4% fiber inclusion. In Experiment 2, 10 diets were arranged as a 2×5 factorial with 2 feed forms (mash vs. crumbles) and 5 levels of AMEn (2,850, 2,900, 2,950, 3,000, and 3,050 kcal/kg). Pullets fed crumbles were heavier and had better FCR than pullets fed mash (P < 0.001). An increase in the energy content of the crumble diets reduced ADFI and improved FCR linearly, but no effects were detected with the mash diets (P < 0.01 and P < 0.05 for the interactions). Feeding crumbles tended to improve BW uniformity at 5 wk age (P = 0.077) but no effects were detected with increases in energy concentration of the diet. In summary, the inclusion of moderate amounts of fiber in the diet improves pullet performance from hatching to 5 wk age. The response of pullets to increases in energy content of the diet depends on feed form with a decrease in feed intake when fed crumbles but no changes when fed mash. Feeding crumbles might be preferred to feeding mash in pullets from hatching to 5 wk age.

Inclusion of fiber in diets for brown-egg laying pullets: Effects on growth performance and digestive tract traits from hatching to 17 weeks of age

We investigated the effects of fiber inclusion in the diet on growth performance and digestive traits in pullets from hatching to 17 wk of age. The control diets of the 3 feeding periods (0 to 5 wk, 5 to 10 wk, and 10 to 17 wk) were based on corn and soybean meal and did not include any additional fiber source. The experimental diets included 2 or 4% of cereal straw or sugar beet pulp (SBP) at the expense (wt:wt) of the control diet. From 0 to 5 wk of age, fiber inclusion did not affect pullet performance. From hatch to 17 wk of age, the inclusion of straw had little effect on pullet performance but the inclusion of 4% SBP reduced (ADG) (P < 0.05) and reduced feed conversion ratio (FCR; P < 0.001). Pullets fed straw had greater ADG (P < 0.05) and better energy conversion ratio (P < 0.01) than pullets fed SBP. An increase in fiber from 2 to 4% reduced FCR (P < 0.05). Body weight uniformity was not affected by diet. Fiber inclusion increased the relative weight (% BW) of the gizzard at 5 wk (P = 0.056) and 10 wk (P < 0.01) of age, but no differences were detected between fiber sources. At same ages, the relative length (cm/kg BW) of the pullets (P = 0.058 and P < 0.01, respectively) and tarsus (P = 0.079 and P < 0.05, respectively) was higher in pullets fed SBP than in pullets fed straw. Fiber inclusion, however, did not affect any of these traits at 17 wk of age. In summary, the inclusion of 2% straw at the expense (wt:wt) of the whole diet did not affect pullet performance at 17 wk of age. An increase in the level of straw from 2 to 4% reduced FCR but did not affect ADG. The inclusion of SBP, however, reduced pullet growth, with effects being more pronounced at the higher level.