Optimum Design of an Envelope Tracking Buck Converter for RF PA using GaN HEMTs

In this paper, filter design methodology and application of GaN HEMTs for high efficiency Envelope Amplifier in RF transmitters are proposed. The main objectives of the filter design are generation of the envelope reference with the minimum possible distortion and high efficiency of the amplifier obtained by the optimum trade-off between conduction and switching losses. This optimum point was determined using power losses model for synchronous buck with sinusoidal output voltage and experimental results showed good correspondence with the model and verified the proposed methodology. On the other hand, comparing to Si MOSFETs, GaN HEMTs can provide higher efficiency of the envelope amplifier, due to superior conductivity and switching characteristics. Experimental results verified benefits of GaN devices comparing to the appliance of Si switching devices with very good Figure Of Merit, for this particular application

Serial or Parallel Linear-Assisted Switching Converter as Envelope Amplifier: Optimization and Comparison

This paper presents a theoretical analysis and an optimization method for envelope amplifier. Highly efficient envelope amplifiers based on a switching converter in parallel or series with a linear regulator have been analyzed and optimized. The results of the optimization process have been shown and these two architectures are compared regarding their complexity and efficiency. The optimization method that is proposed is based on the previous knowledge about the transmitted signal type (OFDM, WCDMA...) and it can be applied to any signal type as long as the envelope probability distribution is known. Finally, it is shown that the analyzed architectures have an inherent efficiency limit.

Teaching digital control of switch mode power supplier

This paper explains the methodology followed to teach the subject `Digital control of power converters'. This subject belongs to the research master on `Industrial Electronics' of the Universidad Politécnica de Madrid. The subject is composed of several theoretical lessons plus the development of an actual digital control. For that purpose an ad hoc dc-dc converter has been designed and built. The use of this board together with some software tools seems a very powerful way for the students to learn the concepts from the design to the real world

Potencial del cultivo de la chumbera (Opuntia ficus-indica (L) Miller) para la obtención de biocombustibles

El presente trabajo trata sobre el potencial del cultivo de chumbera (Opuntia ficus-indica (L) Miller) para la obtención de dos biocombustibles: bioetanol y biogás. Para lograr este objetivo se ha estudiado, por una parte, el empleo de procedimientos orientados a la producción de bioetanol no celulósico a partir de cladodios de chumbera, lo que ha dado como resultado rendimientos de entre 156 y 221 litros de etanol por cada tonelada de materia seca de biomasa, y, por otra, la obtención de biogás mediante la digestión anaeróbica de los mismos en régimen mesófilo, donde se han hallado rendimientos en torno a 198 m3 de metano por tonelada de materia seca. Una vez determinado el potencial de la materia prima se han diseñado procesos para una escala industrial que permitan la transformación de los cladodios de chumbera en ambos biocombustibles y se han determinado sus balances energéticos, los cuales han dado como resultado la autosuficiencia de ambos procesos, obteniéndose, además, un excedente térmico de 1.235 kcal L-1 de etanol producido, y en torno a 140 kep de energía total (térmica + eléctrica) por tonelada de materia seca empleada en la digestión anaeróbica. Por último se ha estimado el potencial de producción de ambos combustibles en un área apta para el cultivo de la chumbera. En concreto, este estudio se ha llevado a cabo para la provincia de Almería, elegida por tratarse de una zona con cierta tradición en el manejo de esta planta y presentar un clima semiárido mediterráneo. La superficie apta para el cultivo de la chumbera en esta provincia se ha estimado en 100.616 ha y el rendimiento medio del cultivo en 5 t MS ha-1 año-1. En el caso del bioetanol esto implicaría un potencial de producción en torno a 82.158 m3 año-1 que podrían dar lugar a la creación de dos macrodestilerías (con una producción de 100.000 L diarios) o de 49 microdestilerías (con 5.000 L diarios de producción). Si se optara por la transformación de la biomasa de chumbera en metano, podrían obtenerse 99,4 M de metros cúbicos, lo cual permitiría el establecimiento de 79 plantas de cogeneración de 500 kW cada una. ABSTRACT The present work deals with the potential of prickly pear (Opuntia ficus-indica (L) Mill.) biomass as a feedstock for bioethanol and biogas. In order to reach this objective different procedures aiming at the production of non-cellulosic bioethanol from cladodes were carried out; yields from156 to 221 litres of bioethanol per ton of dry matter were found. Mesophilic anaerobic digestion of cladodes was also studied and yields around 198 m3 of methane per ton of dry matter were reached. From these results, processes on an industrial scale were designed for both pathways of energy conversion of prickly-pear biomass and the respective energy balances were calculated. They resulted to be self-sufficient from an energetic point of view; the bioethanol pathway generated a thermal energy surplus of 1,235 kcal per litre of ethanol, while around 140 kep of total energy (heat + electricity) were obtained from the anaerobic digestion of one ton of dry cladodes. Finally, the potential production of both biofuels from prickly pear biomass was estimated for a specific area. The province of Almeria was chosen because of its climate conditions and the previous existence of prickly pear plantations. The area suitable for prickly pear cultivation in the province was estimated at a maximum of 100.616 ha, with an average yield of about 5 t DM ha-1 year-1. If prickly pear biomass were cropped for bioethanol in Almeria, the potential production of bioethanol could reach 82,158 m3 year-1, in either two macrodistilleries (100,000 L day-1) or 49 microdestilleries (5,000 L day-1). If the biogas pathway were preferred, 99. 4 Mm3 of methane could be reached and this would represent 79 CHP plants (500 kW each one).

Diffuse illuminance availability on horizontal and vertical surfaces at Madrid, Spain

The overall objective of this work is to provide diffuse illuminance availability at Madrid (Spain) through a statistical analysis of illuminance values corresponding to a long-term data series. The illuminance values are obtained from irradiance measurements by means of different empirical models for luminous efficacy. The values of diffuse illuminance on a horizontal and on vertical surfaces facing the four cardinal points are estimated and the different aspects related to daylight availability in an area with specific climatic conditions are analyzed. The experimental data consist of global and diffuse irradiance measurements on a horizontal surface provided by the National Meteorological Agency in Spain (AEMET) for Madrid. These data consist of hourly values measured in the period of 1980–2005. The statistical results derived correspond to a daylight typical year for the five surfaces considered. This information will be useful to building experts to estimate natural illumination availability when daylighting techniques are applied in building design with the main aim of electric energy savings.

Effect of the oxygen isoelectronic substitution in Cu2ZnSnS4 and its photovoltaic application

The optoelectronic properties of Cu2ZnSnS4 and environmental considerations have attracted significant interest for photovoltaics. Using first-principles, we analyze the possible improvement of this material as a photovoltaic absorber via the isoelectronic substitution of S with O atoms. The evolution of the acceptor level is analyzed with respect to the atomic position of the nearest neighbors of the O atom. We estimate the maximum efficiency of this compound when used as a light absorber. The presence of the sub-band gap level below the conduction band could increases the solar-energy conversion with respect to the host.

Nano-imprinted rear-side diffraction gratings for absorption enhancement in solar cells

As wafer-based solar cells become thinner, light-trapping textures for absorption enhancement will gain in importance. In this work, crystalline silicon wafers were textured with wavelength-scale diffraction grating surface textures by nanoimprint lithography using interference lithography as a mastering technology. This technique allows fine-tailored nanostructures to be realized on large areas with high throughput. Solar cell precursors were fabricated, with the surface textures on the rear side, for optical absorption measurements. Large absorption enhancements are observed in the wavelength range in which the silicon wafer absorbs weakly. It is shown experimentally that bi-periodic crossed gratings perform better than uni-periodic linear gratings. Optical simulations have been made of the fabricated structures, allowing the total absorption to be decomposed into useful absorption in the silicon and parasitic absorption in the rear reflector. Using the calculated silicon absorption, promising absorbed photocurrent density enhancements have been calculated for solar cells employing the nano-textures. Finally, first results are presented of a passivation layer deposition technique that planarizes the rear reflector for the purpose of reducing the parasitic absorption.

Optimal design of AC EMI filters with damping networks and effect on the systems power factor

The cutoff frequencies of an EMI filter are normally given by the noise attenuation requirements the filter has to fulfill. In order to select the component values of the filter elements, i.e. inductances and capacitances, an additional design criterium is needed. In this paper the effect of the EMI filter input and output impedances are considered. The input impedance influences the filters effect on the system displacement power factor and the output impedance plays a key role in the system stability. The effect of filter element values, the number of filter stages as well as additional damping networks are considered and a design procedure is provided. For this analysis a two-port description of the input filters employing ABCD-parameters is used.

Hybrid behavioral-analytical loss model for a high frequency and low load DC/DC buck converter

This work presents a behavioral-analytical hybrid loss model for a buck converter. The model has been designed for a wide operating frequency range up to 4MHz and a low power range (below 20W). It is focused on the switching losses obtained in the power MOSFETs. Main advantages of the model are the fast calculation time (below 8.5 seconds) and a good accuracy, which makes this model suitable for the optimization process of the losses in the design of a converter. It has been validated by simulation and experimentally with one GaN power transistor and three Si MOSFETs. Results show good agreement between measurements and the model

Envelope Amplifier Based on a Hybrid Series Converter With The Slow-envelope Technique

High frequency dc-dc switching converters are used as envelope amplifiers in RF transmitters. The dc-dc converter should operate at very high frequency to track an envelope in the MHz range to supply the power amplifier. One of the circuits suitable for this application is a hybrid topology composed of a switched converter and a linear regulator in series that work together to adjust the output voltage to track the envelope with accuracy. This topology can take advantage of the reduced slew-rate technique where switching dc-dc converter provides the RF envelope with limited slew rate in order to avoid high switching frequency and high power losses, while the linear regulator performs fine adjustment in order to obtain the exact replica of the RF envelope. The combination of this control technique with this topology is proposed in this paper. Envelopes with different bandwidth will be considered to optimize the efficiency of the dc-dc converter. The calculations and experiments have been done to track a 2MHz envelope in the range 0-12V for an EER RF transmitter.

Core physics and safety analysis of Generation-IV Sodium Fast Reactors using existing and newly developed computational tools

El futuro de la energía nuclear de fisión dependerá, entre otros factores, de la capacidad que las nuevas tecnologías demuestren para solventar los principales retos a largo plazo que se plantean. Los principales retos se pueden resumir en los siguientes aspectos: la capacidad de proporcionar una solución final, segura y fiable a los residuos radiactivos; así como dar solución a la limitación de recursos naturales necesarios para alimentar los reactores nucleares; y por último, una mejora robusta en la seguridad de las centrales que en definitiva evite cualquier daño potencial tanto en la población como en el medio ambiente como consecuencia de cualquier escenario imaginable o más allá de lo imaginable. Siguiendo estas motivaciones, la Generación IV de reactores nucleares surge con el compromiso de proporcionar electricidad de forma sostenible, segura, económica y evitando la proliferación de material fisible. Entre los sistemas conceptuales que se consideran para la Gen IV, los reactores rápidos destacan por su capacidad potencial de transmutar actínidos a la vez que permiten una utilización óptima de los recursos naturales. Entre los refrigerantes que se plantean, el sodio parece una de las soluciones más prometedoras. Como consecuencia, esta tesis surgió dentro del marco del proyecto europeo CP-ESFR con el principal objetivo de evaluar la física de núcleo y seguridad de los reactores rápidos refrigerados por sodio, al tiempo que se desarrollaron herramientas apropiadas para dichos análisis. Efectivamente, en una primera parte de la tesis, se abarca el estudio de la física del núcleo de un reactor rápido representativo, incluyendo el análisis detallado de la capacidad de transmutar actínidos minoritarios. Como resultado de dichos análisis, se publicó un artículo en la revista Annals of Nuclear Energy [96]. Por otra parte, a través de un análisis de un hipotético escenario nuclear español, se evalúo la disponibilidad de recursos naturales necesarios en el caso particular de España para alimentar una flota específica de reactores rápidos, siguiendo varios escenarios de demanda, y teniendo en cuenta la capacidad de reproducción de plutonio que tienen estos sistemas. Como resultado de este trabajo también surgió una publicación en otra revista científica de prestigio internacional como es Energy Conversion and Management [97]. Con objeto de realizar esos y otros análisis, se desarrollaron diversos modelos del núcleo del ESFR siguiendo varias configuraciones, y para diferentes códigos. Por otro lado, con objeto de poder realizar análisis de seguridad de reactores rápidos, son necesarias herramientas multidimensionales de alta fidelidad específicas para reactores rápidos. Dichas herramientas deben integrar fenómenos relacionados con la neutrónica y con la termo-hidráulica, entre otros, mediante una aproximación multi-física. Siguiendo este objetivo, se evalúo el código de difusión neutrónica ANDES para su aplicación a reactores rápidos. ANDES es un código de resolución nodal que se encuentra implementado dentro del sistema COBAYA3 y está basado en el método ACMFD. Por lo tanto, el método ACMFD fue sometido a una revisión en profundidad para evaluar su aptitud para la aplicación a reactores rápidos. Durante ese proceso, se identificaron determinadas limitaciones que se discutirán a lo largo de este trabajo, junto con los desarrollos que se han elaborado e implementado para la resolución de dichas dificultades. Por otra parte, se desarrolló satisfactoriamente el acomplamiento del código neutrónico ANDES con un código termo-hidráulico de subcanales llamado SUBCHANFLOW, desarrollado recientemente en el KIT. Como conclusión de esta parte, todos los desarrollos implementados son evaluados y verificados. En paralelo con esos desarrollos, se calcularon para el núcleo del ESFR las secciones eficaces en multigrupos homogeneizadas a nivel nodal, así como otros parámetros neutrónicos, mediante los códigos ERANOS, primero, y SERPENT, después. Dichos parámetros se utilizaron más adelante para realizar cálculos estacionarios con ANDES. Además, como consecuencia de la contribución de la UPM al paquete de seguridad del proyecto CP-ESFR, se calcularon mediante el código SERPENT los parámetros de cinética puntual que se necesitan introducir en los típicos códigos termo-hidráulicos de planta, para estudios de seguridad. En concreto, dichos parámetros sirvieron para el análisis del impacto que tienen los actínidos minoritarios en el comportamiento de transitorios. Concluyendo, la tesis presenta una aproximación sistemática y multidisciplinar aplicada al análisis de seguridad y comportamiento neutrónico de los reactores rápidos de sodio de la Gen-IV, usando herramientas de cálculo existentes y recién desarrolladas ad' hoc para tal aplicación. Se ha empleado una cantidad importante de tiempo en identificar limitaciones de los métodos nodales analíticos en su aplicación en multigrupos a reactores rápidos, y se proponen interesantes soluciones para abordarlas. ABSTRACT The future of nuclear reactors will depend, among other aspects, on the capability to solve the long-term challenges linked to this technology. These are the capability to provide a definite, safe and reliable solution to the nuclear wastes; the limitation of natural resources, needed to fuel the reactors; and last but not least, the improved safety, which would avoid any potential damage on the public and or environment as a consequence of any imaginable and beyond imaginable circumstance. Following these motivations, the IV Generation of nuclear reactors arises, with the aim to provide sustainable, safe, economic and proliferationresistant electricity. Among the systems considered for the Gen IV, fast reactors have a representative role thanks to their potential capacity to transmute actinides together with the optimal usage of natural resources, being the sodium fast reactors the most promising concept. As a consequence, this thesis was born in the framework of the CP-ESFR project with the generic aim of evaluating the core physics and safety of sodium fast reactors, as well as the development of the approppriated tools to perform such analyses. Indeed, in a first part of this thesis work, the main core physics of the representative sodium fast reactor are assessed, including a detailed analysis of the capability to transmute minor actinides. A part of the results obtained have been published in Annals of Nuclear Energy [96]. Moreover, by means of the analysis of a hypothetical Spanish nuclear scenario, the availability of natural resources required to deploy an specific fleet of fast reactor is assessed, taking into account the breeding properties of such systems. This work also led to a publication in Energy Conversion and Management [97]. In order to perform those and other analyses, several models of the ESFR core were created for different codes. On the other hand, in order to perform safety studies of sodium fast reactors, high fidelity multidimensional analysis tools for sodium fast reactors are required. Such tools should integrate neutronic and thermal-hydraulic phenomena in a multi-physics approach. Following this motivation, the neutron diffusion code ANDES is assessed for sodium fast reactor applications. ANDES is the nodal solver implemented inside the multigroup pin-by-pin diffusion COBAYA3 code, and is based on the analytical method ACMFD. Thus, the ACMFD was verified for SFR applications and while doing so, some limitations were encountered, which are discussed through this work. In order to solve those, some new developments are proposed and implemented in ANDES. Moreover, the code was satisfactorily coupled with the thermal-hydraulic code SUBCHANFLOW, recently developed at KIT. Finally, the different implementations are verified. In addition to those developments, the node homogenized multigroup cross sections and other neutron parameters were obtained for the ESFR core using ERANOS and SERPENT codes, and employed afterwards by ANDES to perform steady state calculations. Moreover, as a result of the UPM contribution to the safety package of the CP-ESFR project, the point kinetic parameters required by the typical plant thermal-hydraulic codes were computed for the ESFR core using SERPENT, which final aim was the assessment of the impact of minor actinides in transient behaviour. All in all, the thesis provides a systematic and multi-purpose approach applied to the assessment of safety and performance parameters of Generation-IV SFR, using existing and newly developed analytical tools. An important amount of time was employed in identifying the limitations that the analytical nodal diffusion methods present when applied to fast reactors following a multigroup approach, and interesting solutions are proposed in order to overcome them.

Realistic detailed balance study of the quantum efficiency of quantum dot solar cells

An attractive but challenging technology for high efficiency solar energy conversion is the intermediate band solar cell (IBSC), whose theoretical efficiency limit is 63%, yet which has so far failed to yield high efficiencies in practice. The most advanced IBSC technology is that based on quantum dots (QDs): the QD-IBSC. In this paper, k·p calculations of photon absorption in the QDs are combined with a multi-level detailed balance model. The model has been used to reproduce the measured quantum efficiency of a real QD-IBSC and its temperature dependence. This allows the analysis of individual sub-bandgap transition currents, which has as yet not been possible experimentally, yielding a deeper understanding of the failure of current QD-IBSCs. Based on the agreement with experimental data, the model is believed to be realistic enough to evaluate future QD-IBSC proposals.

Performance metrics for small-signal stability assessment of DC-distributed power-system-architecture comparisons

The objective of this paper is to provide performance metrics for small-signal stability assessment of a given system architecture. The stability margins are stated utilizing a concept of maximum peak criteria (MPC) derived from the behavior of an impedance-based sensitivity function. For each minor-loop gain defined at every system interface, a single number to state the robustness of stability is provided based on the computed maximum value of the corresponding sensitivity function. In order to compare various power-architecture solutions in terms of stability, a parameter providing an overall measure of the whole system stability is required. The selected figure of merit is geometric average of each maximum peak value within the system. It provides a meaningful metrics for system comparisons: the best system in terms of robust stability is the one that minimizes this index. In addition, the largest peak value within the system interfaces is given thus detecting the weakest point of the system in terms of robustness.

Electrodynamic tether for scientific mission in low Jovian orbit

An electrodynamic bare tether is shown to allow carrying out scientific observations very close to Jupiter, for exploration of its surface and subsurface, and ionospheric and atmospheric in-situ measurements. Starting at a circular equatorial orbit of radius about 1.3/1.4 times the Jovian radius, continuous propellantless Lorentz drag on a thin-tape tether in the 1-5 km length range would make a spacecraft many times as heavy as the tape slowly spiral in, over a period of many months, while generating power at a load plugged in the tether circuit for powering instruments in science data acquisition and transmission. Lying under the Jovian radiation belts, the tape would avoid the most severe problem facing tethers in Jupiter, which are capable of producing both power and propulsion but, operating slowly, could otherwise accumulate too high a radiation dose . The tether would be made to spin in its orbit to keep taut; how to balance the Lorentz torque is discussed. Constraints on heating and bowing are also discussed, comparing conditions for prograde versus retrograde orbits. The system adapts well to the moderate changes in plasma density and motional electric field through the limited radial range in their steep gradients near Jupiter.

A proposed bare-tether experiment on board a sounding rocket

A mission on board a sounding rocket to carry out two bare-tether experiments is proposed: a test of orbital-motion-limited (OML) collection and the proof-of-flight of a technique to determine the (neutral) density vertical profile in the critical E-layer. Since full bias from the motional field will be small (~ 20V), corresponding to a tape 1 km long and V rocket <8 km/s, a power source with a range of supply voltages of few kV would be used. First, the negative terminal of the supply would be connected to the tape, and the positive terminal to a round, conductive boom of length 10 - 20 m; electrons collected by the boom cross the supply into the tape, where they leak out at the rate of ion impact plus secondary emission. Determination of the density profile from measurements of auroral emissions observed from the rocket, as secondaries racing down the magnetic field reach an E-layer footprint, are discussed. Next the positive terminal of the voltage supply is connected to the tape, and the negative terminal to a Hollow Cathode (HC); electrons now collected by the tape cross the supply, and are ejected at the HC. The opposite connections, with current collection operated by tape and boom, and operating on electrons and ions, and through partial switching in the supply, allow testing OML collection in almost all respects it depends on.