Tertiary Treatment of Ayr Municipal Wastewater using Bioremediation: A Pilot-Scale Study. A Report Prepared for the Burdekin Shire Council and the Burdekin Rangeland Reef Initiative

This joint DPI/Burdekin Shire Council project assessed the efficacy of a pilot-scale biological remediation system to recover Nitrogen (N) and Phosphorous (P) nutrients from secondary treated municipal wastewater at the Ayr Sewage Treatment Plant. Additionally, this study considered potential commercial uses for by-products from the treatment system. Knowledge gained from this study can provide directions for implementing a larger-scale final effluent treatment protocol on site at the Ayr plant. Trials were conducted over 10 months and assessed nutrient removal from duckweed-based treatments and an algae/fish treatment – both as sequential and as stand-alone treatment systems. A 42.3% reduction in Total N was found through the sequential treatment system (duckweed followed by algae/fish treatment) after 6.6 days Effluent Retention Time (E.R.T.). However, duckweed treatment was responsible for the majority of this nutrient recovery (7.8 times more effective than algae/fish treatment). Likewise, Total P reduction (15.75% reduction after 6.6 days E.R.T.) was twice as great in the duckweed treatment. A phytoplankton bloom, which developed in the algae/fish tanks, reduced nutrient recovery in this treatment. A second trial tested whether the addition of fish enhanced duckweed treatment by evaluating systems with and without fish. After four weeks operation, low DO under the duckweed blanket caused fish mortalities. Decomposition of these fish led to an additional organic load and this was reflected in a breakdown of nitrogen species that showed an increase in organic nitrogen. However, the Dissolved Inorganic Nitrogen (DIN: ammonia, nitrite and nitrate) removal was similar between treatments with and without fish (57% and 59% DIN removal from incoming, respectively). Overall, three effluent residence times were evaluated using duckweed-based treatments; i.e. 3.5 days, 5.5 days and 10.4 days. Total N removal was 37.5%, 55.7% and 70.3%, respectively. The 10.4-day E.R.T. trial, however, was evaluated by sequential nutrient removal through the duckweed-minus-fish treatment followed by the duckweed-plus-fish treatment. Therefore, the 70.3% Total N removal was lower than could have been achieved at this retention time due to the abovementioned fish mortalities. Phosphorous removal from duckweed treatments was greatest after 10.4-days E.R.T. (13.6%). Plant uptake was considered the most important mechanism for this P removal since there was no clay substrate in the plastic tanks that could have contributed to P absorption as part of the natural phosphorous cycle. Duckweed inhibited phytoplankton production (therefore reducing T.S.S) and maintained pH close to neutral. DO beneath the duckweed blanket fell to below 1ppm; however, this did not limit plant production. If fish are to be used as part of the duckweed treatment, air-uplifts can be installed that maintain DO levels without disturbing surface waters. Duckweed grown in the treatments doubled its biomass on average every 5.7 days. On a per-surface area basis, 1.23kg/m2 was harvested weekly. Moisture content of duckweed was 92%, equating to a total dry weight harvest of 0.098kg/m2/week. Nutrient analysis of dried duckweed gave an N content of 6.67% and a P content of 1.27%. According to semi-quantitative analyses, harvested duckweed contained no residual elements from the effluent stream that were greater than ANZECC toxicant guidelines proposed for aquaculture. In addition, jade perch, a local aquaculture species, actively consumed and gained weight on harvested duckweed, suggesting potential for large-scale fish production using by-products from the effluent treatment process. This suggests that a duckweed-based system may be one viable option for tertiary treatment of Ayr municipal wastewater. The tertiary detention lagoon proposed by the Burdekin Shire Council, consisting of six bays approximately 290 x 35 metres (x 1.5 metres deep), would be suitable for duckweed culture with minor modification to facilitate the efficient distribution of duckweed plants across the entire available growing surface (such as floating containment grids). The effluent residence time resulting from this proposed configuration (~30 days) should be adequate to recover most effluent nutrients (certainly N) based on the current trial. Duckweed harvest techniques on this scale, however, need to be further investigated. Based on duckweed production in the current trial (1.23kg/m2/week), a weekly harvest of approximately 75 000kg (wet weight) could be expected from the proposed lagoon configuration under full duckweed production. A benefit of the proposed multi-bay lagoon is that full lagoon production of duckweed may not be needed to restore effluent to a desirable standard under the present nutrient load, and duckweed treatment may be restricted to certain bays. Restored effluent could be released without risk of contaminating the receiving waterway with duckweed by evacuating water through an internal standpipe located mid-way in the water column.

Removal of endocrine disrupting compounds from wastewater: a comparison between a conventional activated sludge with tertiary treatment and membrane bioreactors

Póster presentado en 19th International Congress of Chemical and Process Engineering, Prague, Czech Republic August 28th-September 1st, 2010.

Complementary methods to investigate the development of clogging within a horizontal sub-surface flow tertiary treatment wetland

A combination of experimental methods was applied at a clogged, horizontal subsurface flow (HSSF) municipal wastewater tertiary treatment wetland (TW) in the UK, to quantify the extent of surface and subsurface clogging which had resulted in undesirable surface flow. The three dimensional hydraulic conductivity profile was determined, using a purpose made device which recreates the constant head permeameter test in-situ. The hydrodynamic pathways were investigated by performing dye tracing tests with Rhodamine WT and a novel multi-channel, data-logging, flow through Fluorimeter which allows synchronous measurements to be taken from a matrix of sampling points. Hydraulic conductivity varied in all planes, with the lowest measurement of 0.1 md1 corresponding to the surface layer at the inlet, and the maximum measurement of 1550 md1 located at a 0.4m depth at the outlet. According to dye tracing results, the region where the overland flow ceased received five times the average flow, which then vertically short-circuited below the rhizosphere. The tracer break-through curve obtained from the outlet showed that this preferential flow-path accounted for approximately 80% of the flow overall and arrived 8 h before a distinctly separate secondary flow-path. The overall volumetric efficiencyof the clogged system was 71% and the hydrology was simulated using a dual-path, dead-zone storage model. It is concluded that uneven inlet distribution, continuous surface loading and high rhizosphere resistance is responsible for the clog formation observed in this system. The average inlet hydraulic conductivity was 2 md1, suggesting that current European design guidelines, which predict that the system will reach an equilibrium hydraulic conductivity of 86 md1, do not adequately describe the hydrology of mature systems.

Evaluation of cyanobacteria for biomass production and effluent treatment

The microalgae gained importance as food and feed as well as source of fine chemicals since the l960’s. Spirulina became the trend setter due to its easily culturable properties as well as nutritional composition. A rapid expansion of microalgal industry occurred in the Asia-Pacific region as microalgae came to stay as a health food supplement. Microalgae have been an integral component of oxidation ponds usually incorporated with wastewater treatment. Over the last few decades, efforts have been made to apply intensive microalgal cultures to perform biological tertiary treatment of secondary effluents. Given the limited number of species still available for commercial exploitation, it is imperative to isolate and cultivate those photosynthetic organisms with high growth rate and biomass accumulation, which could play the dual role of cleaning the wastewater and also providing useful biomass. This has been the objective of this study ie. 0 To develop pure cultures of local isolates of Cyanobacteria for extraction of biochemicals of commercial value 0 To couple biomass production with effluent treatment

Application of floating medium filters for aquaculture wastewater treatment

Filtration is an effective process in removing particles of various nature and sizes that are present in water and wastewater. It has been used as a final clarifying step in water treatment since the19th century. It is becoming increasingly important in the tertiary treatment step of wastewater to produce effluent of superior quality for the purpose of reuse. Filtration is particularly applied when high flow rates of water with relatively low contents of suspended solids have to be treated. In a conventional water or wastewater treatment system, the filters are usually placed after sedimentation units to remove suspended particles, which escape without settling in the sedimentation units. When chemically pretreated and flocculated water is applied to a filter without a prior-solid liquid separation it is called direct filtration.

Clogging in subsurface-flow treatment wetlands:occurrence and contributing factors

Clogging is a major operational and maintenance issue associated with the use of subsurface flow wetlands for wastewater treatment, and can ultimately limit the lifetime of the system. This review considers over two decades of accumulated knowledge regarding clogging in both vertical and horizontal subsurface flow treatment wetlands. The various physical, chemical and biological factors responsible for clogging are identified and discussed. The occurrence of clogging is placed into the context of various design and operational parameters such as wastewater characteristics, upstream treatment processes, intermittent or continuous operation, influent distribution, and media type. This information is then used to describe how clogging develops within, and subsequently impacts, common variants of subsurface flow treatment wetland typically used in the U.S., U.K., France and Germany. Comparison of these systems emphasized that both hydraulic loading rate and solids loading rate need to be considered when designing systems to operate robustly, i.e. hydraulic overloading makes horizontal-flow tertiary treatment systems in the U.K. more susceptible to clogging problems than vertical-flow primary treatment systems in France. Future research should focus on elucidating the underlying mechanisms of clogging as they relate to the design, operation, and maintenance of subsurface flow treatment wetlands. © 2010 Elsevier B.V.

Reuse of treated sewage in Delhi city: Microbial evaluation of STPs and reuse options

Microbiological quality of the treated wastewater is an important parameter for its reuse. The data oil the Fecal Coliform (FC) and Fecal Streptococcus (FS) at different stages of treatment in the Sewage Treatment Plants (STPs) in Delhi watershed is not available, therefore in the present study microbial profiling of STPs was carried out to assess the effluent quality for present and future reuse options. This Study further evaluates the water quality profiles at different stages of treatment for 16 STPs in Delhi city. These STPs are based on conventional Activated Sludge Process (ASP), extended aeration, physical, chemical and biological treatment (BIOFORE), Trickling Filter and Oxidation Pond. The primary effluent quality produced from most of the STPs was suitable for Soil Aquifer Treatment (SAT). Extended Hydraulic Retention Time (HRT) as a result Of low inflow to the STPS Was responsible for high turbidity, COD and BODs removal. Conventional ASP based STPs achieved 1.66 log FC and 1.06 log FS removal. STPs with extended aeration treatment process produced better quality effluent with maximum 4 log order reduction in FC and FS levels. ``Kondli'' and ``Nilothi'' STPs employing ASP, produced better quality secondary effluent as compared to other STPs based oil similar treatment process. Oxidation Pond based STPs showed better FC and FS removals, whereas good physiochemical quality was achieved during the first half of the treatment. Based upon physical, chemical and microbiological removal efficiencies, actual integrated efficiency (IEa) of each STP was determined to evaluate its Suitability for reuse for irrigation purposes. Except Mehrauli'' and ``Oxidation Pond'', effluents from all other STPs require tertiary treatment for further reuse. Possible reuse options, depending Upon the geographical location, proximity of facilities of potential users based oil the beneficial uses, and sub-soil types, etc. for the Delhi city have been investigated, which include artificial groundwater recharge, aquaculture, horticulture and industrial uses Such as floor washing, boiler feed, and cooling towers, etc. (C) 2009 Elsevier B.V. All rights reserved.

Application of algal bioassays in the determination of eutrophic power of waste water (”Conclusions” only) [Translation from: 1g.Sanita pubbl. 31 257-267, 1975]

The best evidence for establishing the level of eutrophy of a water-body is its algal production which makes it possible to identify the type and the intensity of the eutrophication according to the kind and number of algal species present: when the number of algae exceeds half a million per litre then one speaks o an ”algal bloom”. The scope of the present research aims to verify if the alga Selenastrum capricornutum can be used as a test alga under our culture conditions and to determine the eutrophic level of the secondary effluent of a modern plant for the treatment of domestic discharge and to investigate the eventual ”limiting factors”. Finally this paper aims to study the effect on the secondary effluent of tertiary treatment carried out artificially in the laboratory.

Estações de tratamento de águas residuais: conceitos e dimensionamento

O presente relatório é o corolário do Estágio Curricular que a autora efetuou, durante o segundo semestre do ano letivo de 2014/2015 na SBS – Engenharia Civil, Hidráulica e Ambiente, Lda. Nesta empresa a autora foi integrada na equipa técnica que elaborou um Projeto de Execução para uma Estação de Tratamento de Águas Residuais que irá ser construída em Montemor-o-Novo, tendo-lhe sido atribuídas as seguintes tarefas principais: i) estudo de ferramentas de dimensionamento de ETAR; e ii) estudo dos processos de tratamento de águas residuais a instalar. O tratamento de águas residuais não é matéria que conste do atual Plano de Estudos do Mestrado em Engenharia Civil do ISEP. Este facto, associado à premente necessidade de dar resposta às expectativas da Entidade Acolhedora, obrigou a autora a um esforço de aprendizagem significativo. Nesta fase foi executada uma aprofundada pesquisa bibliográfica que permitiu à autora obter o nível de conhecimentos teóricos necessário para a plena integração na Equipa de Projeto. Já integrada na Equipa de Projeto o primeiro trabalho desenvolvido pela autora foi a análise detalhada do Caderno de Encargos e da respetiva Nota Técnica. Seguidamente a autora participou em todas as fases do Projeto tendo, por isso, colaborado na análise do Estudo Geotécnico, no dimensionamento dos órgãos da ETAR, no cálculo do perfil hidráulico, na definição de formas (plantas e cortes) dos órgãos, na elaboração da Lista de Equipamentos e do Mapa de Quantidades e, por último, na elaboração da Memória Descritiva e Justificativa do Processo de Tratamento e Equipamentos. O Caso Prático incluído no presente documento é, em larga medida, o corolário do processo de aprendizagem de que a autora beneficiou no decorrer do Estágio Curricular. Grande parte das tarefas que a autora executou ao longo da elaboração do projeto relacionaram-se com o dimensionamento dos órgãos da ETAR e com os respetivos cálculos hidráulicos. Os conhecimentos teórico-práticos desta forma adquiridos foram reunidos num conjunto de ferramentas, maioritariamente folhas de cálculo, que se verificou serem úteis nos processos de dimensionamento e de teste de soluções alternativas. É parte integrante deste relatório um capítulo no qual é feita uma detalhada apresentação dos conceitos teóricos subjacentes ao Projeto de ETAR. Este capítulo reflete o estudo que a autora teve necessidade de efetuar antes de se sentir capaz de integrar a Equipa de Projeto.

Determination of microalgae cellular composition after phycoremediation of swine wastewaters.

Phycoremediation of swine wastewaters has been widely reported as an attractive tertiary treatment system, that effectively removes the excessive nutrient loadswhilst offering a valuable source of feedstock biomass. Digestate from an upflow anaerobic sludge blanket (UASB, 6%v/v) and a nitrification reactor (NR; 50% v/v) were used as culturing media to microalgae. Experiments were carried out in lab scale photobioreactors (PBRs) using a consortia of Chlorella and Scenedesmus. Ammonia (44 to 90%) and phosphorus (77%) were efficiently removed from both effluents tested after 4 days. Microalgae biomass harvested from the UASB effluent showed 57, 34 and 1% of proteins, carbohydrates and lipids, respectively. Comparatively, the cellular composition of microalgae grown on NR effluent had lower protein (43%) but higher carbohydrate (42%) contents. Negligible difference in lipid fraction was observed independently of the effluents tested. The results suggest that the biomass harvested from phycoremediation of swine wastewaters can offer a valuable protein and carbohydrate feedstock for nutritional and biotechnological applications.

Catchment phosphorous losses: an export coefficient modelling approach with scenario analysis for water management

This paper presents the development of an export coefficient model to characterise the rates and sources of P export from land to water in four reservoir systems located in a semi-arid rural region in southern of Portugal. The model was developed to enable effective management of these important water resource systems under the EU Water Framework Directive. This is the first time such an approach has been fully adapted for the semi-arid systems typical of Mediterranean Europe. The sources of P loading delivered to each reservoir from its catchment were determined and scenario analysis was undertaken to predict the likely impact of catchment management strategies on the scale of rate of P loading delivered to each water body from its catchment. The results indicate the importance of farming and sewage treatment works/collective septic tanks discharges as the main contributors to the total diffuse and point source P loading delivered to the reservoirs, respectively. A reduction in the total P loading for all study areas would require control of farming practices and more efficient removal of P from human wastes prior to discharge to surface waters. The scenario analysis indicates a strategy based solely on reducing the agricultural P surplus may result in only a slow improvement in water quality, which would be unlikely to support the generation of good ecological status in reservoirs. The model application indicates that a reduction of P-inputs to the reservoirs should first focus on reducing P loading from sewage effluent discharges through the introduction of tertiary treatment (P-stripping) in all major residential areas. The fully calibrated export coefficient modelling approach transferred well to semi-arid regions, with the only significant limitation being the availability of suitable input data to drive the model. Further studies using this approach in semi-arid catchments are now needed to increase the knowledge of nutrient export behaviours in semi-arid regions.

Comportamento do reator seqüencial em batelada (RSB) sob estado estacionário dinâmico utilizando idade do lodo como parâmetro de controle operacional

O reator seqüencial em batelada (RSB) é uma variante de lodos ativados capaz de promover a remoção da matéria orgânica, a remoção dos nutrientes e a separação da fase sólida da líquida em uma unidade. A valorização das áreas urbanas, a carência de tratamento terciário e a crescente necessidade de redução nas dimensões de estações de tratamento de esgoto devem impulsionar o desenvolvimento de pesquisas sobre RSB em curto espaço de tempo. A partir deste cenário, o presente trabalho teve como objetivo modelar o comportamento do reator seqüencial em batelada a partir da teoria desenvolvida por Marais e colaboradores. Dentro deste contexto, a cinética de oxidação dos compostos orgânicos e do nitrogênio na forma amoniacal foi descrita e modelada. O trabalho experimental foi realizado em duas escalas: bancada e piloto. O experimento em escala de bancada foi dividido em duas fases. Foram utilizados dois RSBs e um sistema de fluxo contínuo. Um reator seqüencial em batelada (RSB1) foi operado com idade de lodo. O outro reator em batelada (RSB2) foi operado em função da relação F/M e o sistema de fluxo contínuo (FC1) por idade de lodo. Estes reatores foram utilizados como controle no monitoramento do RSB1 Na primeira fase, os três sistemas removeram apenas matéria orgânica. Na fase seguinte, removeram matéria orgânica e nitrogênio. A partir dos resultados obtidos em escala de bancada, foi possível concluir que o modelo desenvolvido pode ser aplicado ao reator seqüencial em batelada operando com idade de lodo, permitindo determinar a qualidade do efluente, a produção de lodo e o consumo de oxidante. Além disso, foi possível descrever o comportamento da taxa de consumo de oxigênio em função da oxidação da matéria orgânica biodegradável e da oxidação do nitrogênio na forma amoniacal. O reator seqüencial em batelada operado com idade de lodo (RSB1) alcançou remoção média de matéria orgânica de 90 % nas idades de lodo de 30, 20, 10 e 5 dias. A remoção média de nitrogênio mais elevada foi obtida na idade de lodo de 20 dias e atingiu 87 %. Nas demais idades de lodo a remoção média de nitrogênio variou entre 79 e 42 %. A modelagem do comportamento do reator seqüencial em batelada resultou numa proposta de metodologia para o dimensionamento que tem como finalidade abolir critérios obsoletos e inadequados para o dimensionamento de lodos ativados em batelada No experimento em escala piloto, foram utilizados um reator seqüencial em batelada, denominado RSB, e um sistema de fluxo contínuo com a configuração Bardenpho, denominado FC. Os sistemas de lodos ativados sob investigação foram monitorados em duas idades de lodo: 30 e 10 dias. Os dados do experimento em escala piloto mostraram que os processos físico-químicos e biológicos envolvidos na remoção de matéria orgânica e nitrogênio no RSB foram mais eficientes do que no Bardenpho quando trataram o mesmo esgoto doméstico e foram submetidos às mesmas condições operacionais. No RSB, obteve-se 88 e 89 % de remoção de matéria orgânica nas idades de lodo de 10 e 30 dias, respectivamente. Nesta seqüência das idades de lodo, a eficiência do Bardenpho caiu de 87 para 76 %. O sistema de fluxo contínuo removeu 66 e 52 % do nitrogênio total afluente nas idades de lodo de 10 e 30 dias, respectivamente. A eficiência do RSB na remoção de nitrogênio foi determinada apenas na idade de lodo de 10 dias e alcançou 69 %. A partir dos resultados obtidos em escala de bancada e piloto, constata-se que o reator seqüencial em batelada operando com idade de lodo pode ser utilizado no tratamento de esgoto doméstico e obter eficiência na remoção de matéria orgânica e nitrogênio igual ou superior ao sistema de fluxo contínuo.

Tratamento de águas residuárias de suinocultura em reatores anaeróbios horizontais seguidos de reator aeróbio em batelada sequencial

Avaliou-se o desempenho de um sistema combinado anaeróbio-aeróbio para o tratamento de águas residuárias de suinocultura, com concentrações médias de sólidos suspensos totais (SST) de 18.624 e 11.395 mg L-1. Foram utilizados quatro reatores anaeróbios horizontais com volume total de 49,5 L cada, um com manta de lodo (RAHML) e três de leito fixo (RAHLF), instalados em série e seguidos de um reator aeróbio operado em batelada sequencial (RBS) com volume total de 339 L e com alimentação contínua. Nos RAHLF, foram utilizados como meios suporte de anéis de bambu, anéis plásticos de eletroduto corrugado e anéis de bucha (Luffa cillyndrica), respectivamente. Os tempos de detenção hidráulica (TDH) e as cargas orgânicas volumétricas (COV) aplicadas no RAHML foram de 12 e 10 h e 53 e 61 g DQO (L d)-1, respectivamente. O RBS foi operado com ciclo de 24 h e COV de 0,34 e 0,50 g DQO (L d)-1. As eficiências médias de remoção de DQOtotal e SST para o conjunto de reatores anaeróbios horizontais, em série, foram de 96 e 99%, e de 96 e 95%, respectivamente. As maiores produções volumétricas de metano ocorreram nos RAHLF, com valores médios de até 0,744 m³ CH4 (m³ reator d)-1. A inclusão do RBS permitiu melhorar a qualidade do efluente e a estabilidade do sistema de tratamento, atingindo eficiências de remoção de DQOtotal e SST de 99 e 99%, e de 98 e 99%, respectivamente. No RBS, ocorreu nitrificação e desnitrificação, com remoções de N-amoniacal de até 65%.

Complicações intra-operatórias das anestesias do neuroeixo realizadas de maio de 1990 a maio de 2008 na FMB-UNESP: análise retrospectiva

Pós-graduação em Anestesiologia - FMB

Qualidade da matéria-prima de cana-de-açúcar (SP81-3250) submetida à aplicação de maturadores em dois ciclos sucessivos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)