Chemical characterisation of the oligosaccharides in hooded seal (Cystophora cristata) and Australian fur seal (Arctocephalus pusillus doriferus) milk

Carbohydrates were extracted from hooded seal milk, Crystophora cristata (family Phocidae). Free oligosaccharides were separated by gel filtration and then purified by ion exchange chromatography, gel filtration and preparative thin layer or paper chromatography and their structures determined by ¹H-NMR. The hooded seal milk was found to contain inositol and at least nine oligosaccharides, most of which had lacto-N-neotetraose or lacto-N-neohexaose as core units, similar to those in milk of other species of Carnivora such as bears (Ursidae). Their structures were as follows: Gal(β1-4)Glc (lactose); Fuc(α1-2)Gal(β1-4)Glc (2′-fucosyllactose); Gal(β1-4)GlcNAc(β1-3)Gal(β1-4)Glc (lacto-N-neotetraose); Fuc(α1-2)Gal(β1-4)GlcNAc(β1-3)Gal(β1-4)Glc (lacto-N-fucopentaose IV); Gal(β1-4)GlcNAc(β1-3)[Gal(β1-4)GlcNAc(β1-6)]Gal(1-4)Glc (lacto-N-neohexaose); Fuc(α1-2)Gal(β1-4)GlcNAc(β1-3)[Gal(β1-4)GlcNAc(β1-6)]Gal(β1-4)Glc (monofucosyl lacto-N-neohexaose a); Gal(β1-4)GlcNAc(β1-3)[Fuc(α1-2)Gal(β1-4)GlcNAc(β1-6)]Gal(β1-4)Glc (monofucosyl lacto-N-neohexaose b); Fuc(α1-2)Gal(β1-4)GlcNAc(β1-3)[Fuc(α1-2)Gal(β1-4)GlcNAc(β1-6)]Gal(β1-4)Glc (difucosyl lacto-N-neohexaose); Gal(β1-4)GlcNAc(β1-3)Gal(β1-4)GlcNAc(β1-3)Gal(β1-4)Glc (para lacto-N-neohexaose); Fuc(α1-2)Gal(β1-4)GlcNAc(β1-3)Gal(β1-4)GlcNAc(β1-3)Gal(β1-4)Glc (monofucosyl para lacto-N-neohexaose). Milk of the Australian fur seal, Arctophalus pusillus doriferus (family Otariidae) contained inositol but no lactose or free oligosaccharides. These results, therefore, support the hypothesis that the milk of otariids, unlike that of phocids, contains no free reducing saccharides.

Synthesis and comparative physical-chemical characterisation of neutral and cationic amphiphiles using RP-HPLC

A series of norbornane containing amphiphiles was synthesized, their lipophilicity corresponding to neutral and cationic forms was then investigated using reverse phase HPLC (High Performance Liquid Chromatography). This series of amphiphiles incorporated varied lipophilic chain length and also varied distances between the polar/cationic head group from the norbornane scaffold. Our investigation included studying the impact of the stationary phase as a replication of a membrane for both cationic and neutral amphiphiles. The choice of stationary phase was shown to be a very important consideration for this type of measurement. In this connection, C18, Cyano and Polar columns were all investigated, the cyano column was observed to be the optimal stationary phase for the comparison of both charged and neutral amphiphiles.

Preparation and characterisation of metallic glassy/amorphous materials

This thesis studied the plastic deformation behaviour of bulk metallic glasses by conducting indentations on various thermal histories using bonded interface technique. Another effort was to probe the route to fabricate bulk amorphous alloy via consolidating amorphous powder.

Potential of 129Xe NMR spectroscopy of adsorbed xenon for testing the chemical state of the surface of mesoporous carbon materials illustrated by the example of aggregates of diamond and onion-like carbon nanoparticles

The chemical shift in the 129Xe NMR spectrum of adsorbed xenon is very sensitive to the presence of oxygen-containing functional groups on the surface of mesoporous carbon materials. Well-characterized, structurally similar nanodiamond and onion-like carbon samples are considered here as model objects.

Characterisation of minimalist co-assembled fluorenylmethyloxycarbonyl self-assembling peptide systems for presentation of multiple bioactive peptides

The nanofibrillar structures that underpin self-assembling peptide (SAP) hydrogels offer great potential for the development of finely tuned cellular microenvironments suitable for tissue engineering. However, biofunctionalisation without disruption of the assembly remains a key issue. SAPS present the peptide sequence within their structure, and studies to date have typically focused on including a single biological motif, resulting in chemically and biologically homogenous scaffolds. This limits the utility of these systems, as they cannot effectively mimic the complexity of the multicomponent extracellular matrix (ECM). In this work, we demonstrate the first successful co-assembly of two biologically active SAPs to form a coassembled scaffold of distinct two-component nanofibrils, and demonstrate that this approach is more bioactive than either of the individual systems alone. Here, we use two bioinspired SAPs from two key ECM proteins: Fmoc-FRGDF containing the RGD sequence from fibronectin and Fmoc-DIKVAV containing the IKVAV sequence from laminin. Our results demonstrate that these SAPs are able to co-assemble to form stable hybrid nanofibres containing dual epitopes. Comparison of the co-assembled SAP system to the individual SAP hydrogels and to a mixed system (composed of the two hydrogels mixed together post-assembly) demonstrates its superior stable, transparent, shear-thinning hydrogels at biological pH, ideal characteristics for tissue engineering applications. Importantly, we show that only the coassembled hydrogel is able to induce in vitro multinucleate myotube formation with C2C12 cells. This work illustrates the importance of tissue engineering scaffold functionalisation and the need to develop increasingly advanced multicomponent systems for effective ECM mimicry.

STATEMENT OF SIGNIFICANCE: Successful control of stem cell fate in tissue engineering applications requires the use of sophisticated scaffolds that deliver biological signals to guide growth and differentiation. The complexity of such processes necessitates the presentation of multiple signals in order to effectively mimic the native extracellular matrix (ECM). Here, we establish the use of two biofunctional, minimalist self-assembling peptides (SAPs) to construct the first co-assembled SAP scaffold. Our work characterises this construct, demonstrating that the physical, chemical, and biological properties of the peptides are maintained during the co-assembly process. Importantly, the coassembled system demonstrates superior biological performance relative to the individual SAPs, highlighting the importance of complex ECM mimicry. This work has important implications for future tissue engineering studies.

Mechanical characterisation of advanced biomedical materials

Biocompatible Ti, Nb and Mo alloy was fabricated in search of a novel biomaterial for bone regeneration. A series of Ti-based alloys were prepared from elemental powders via powder metallurgy technique. The effects of ball milling variables and the agglomerated particles on mechanical properties of the bulk and porous structures were investigated.

Characterisation of a synthesised fluorescent ligand (4-acridinol-1-sulphonic acid) using nuclear magnetic resonance spectroscopy

The synthesis and complete characterisation of the fluorescent ligand, 4-acridinol-1-sulphonic acid (the acridine analogue of 8-quinolinol-5-sulfonic acid) is described. Using a judicious array of nuclear magnetic resonance spectroscopy experiments, the structural elucidation and full assignment of all proton and carbon chemical shifts were afforded. The 4-acridinol-1-sulphonic acid was found to behave in a similar manner to 8-quinolinol-5-sulphonic acid, forming fluorescent complexes with magnesium(II) and zinc(II). The uncorrected emission maxima for the metal–acridinol complexes were found to be at around 620 nm compared to 505 nm for the respective quinolinol complexes. Unfortunately, preliminary spectrofluorimetric analytical figures of merit revealed that the detection limits of the new acridinol metal complexes were one and a half orders of magnitude poorer than those attained with the corresponding quinolinol ligand. However, in contrast to 8-quinolinol-5-sulphonic acid, the 4-acridinol-1-sulphonic acid ligand showed considerable selectivity for magnesium(II) and zinc(II) over aluminium(III).

Characterisation of galvanneal coatings on strip steel

Galvanneal is a form of zinc-coated sheet steel, where steel is dipped in molten zinc, and then heat treated in a furnace to produce a complex iron-zinc coating. Many industries, such as automotive, use galvanneal for components fabricated from sheet steel. The microstructural properties of galvanneal have a significant influence on how well the sheet metal changes shape on stamping. By means of optical microscopy, scanning electron microscopy, and glow-discharge optical emission spectrometry, we present a study of the microstructure of several galvanneal samples, both stamped and unformed, relating the phases and morphology of the coatings to performance in stamping operations. Samples of galvanneal were subjected to different heat-treatment temperatures. The frequency of defects in stamped components was found to be related to the average alloy content in the coatings, which varied with furnace temperature. An increased average iron content in the coatings was related to increased powdering defects in stamping operations that use galvanneal coated sheet steel.

Precipitate characterisation of an advanced high-strength low-alloy (HSLA) steel using atom probe tomography

Increased fuel economy, combined with the need for the improved safety has generated the development of new hot-rolled high-strength low-alloy (HSLA) and multiphase steels such as dual-phase or transformation-induced plasticity steels with improved ductility without sacrificing strength and crash resistance. However, the modern multiphase steels with good strength-ductility balance showed deteriorated stretch-flangeability due to the stress concentration region between the soft ferrite and hard martensite phases [1]. Ferritic, hot-rolled steels can provide good local elongation and, in turn, good stretch-flangeability [2]. However, conventional HSLA ferritic steels only have a tensile strength of not, vert, similar600 MPa, while steels for the automotive industry are now required to have a high tensile strength of not, vert, similar780 MPa, with excellent elongation and stretch-flangeability [1]. This level of strength and stretch-flangeability can only be achieved by precipitation hardening of the ferrite matrix with very fine precipitates and by ferrite grain refinement. It has been suggested that Mo [3] and Ti [4] should be added to form carbides and decrease the coiling temperature to 650 °C since only a low precipitation temperature can provide the precipitation refinement [4]. These particles appeared to be (Ti, Mo)C, with a cubic lattice and a parameter of 0.433 nm, and they were aligned in rows [4]. It was reported [4] that the formation of these very fine carbides led to an increase in strength of not, vert, similar300 MPa. However, the detailed analysis of these particles has not been performed to date due to their nanoscale size. The aim of this work was to carry out a detailed investigation using atom probe tomography (APT) of precipitates formed in hot-rolled low-carbon steel containing additions Ti and Mo.

The investigated low-carbon steel, containing Fe–0.1C–1.24Mn–0.03Si–0.11Cr–0.11Mo–0.09Ti–0.091Al at.%, was produced by hot rolling. The processing route has been described in detail elsewhere [5] European Patent Application, 1616970 A1, 18.01.2006.[5]. The microstructure was characterised by transmission electron microscopy (TEM) on a Philips CM 20, operated at 200 kV using thin foil and carbon replica techniques. Qualitative energy dispersive X-ray spectroscopy (EDXS) was used to analyse the chemical composition of particles. The atomic level of particle characterisation was performed at the University of Sydney using a local electrode atom probe [6]. APT was carried out using a pulse repetition rate of 200 kHz and a 20% pulse fraction on the sample with temperature of 80 K. The extent of solute-enriched regions (radius of gyration) and the local solute concentrations in these regions were estimated using the maximum separation envelope method with a grid spacing of 0.1 nm [7]. A maximum separation distance between the atoms of interest of dmax = 1 nm was used.

The microstructure of the steel consisted of two types of fine ferrite grains: (i) small recrystallised grains with an average grain size of 1.4 ± 0.2 μm; and (ii) grains with a high dislocation density (5.8 ± 1.4 × 1014 m−2) and an average grain size of 1.9 ± 0.1 μm in thickness and 2.7 ± 0.1 μm in length (Fig. 1a). Some grains with high dislocation density displayed an elongated shape with Widmanstätten side plates and also the formation of cells and subgrains (Fig. 1a). The volume fraction of recrystallised grains was 34 ± 8%.

Nano- and macro-scale characterisation of the mechanical properties of bovine bone

In the present study, nano- and macro-scale characterisations on the mechanical properties of bovine cortical bones have been performed by using nanoindentation and conventional compressive tests. Nanoindentation results showed that the elastic modulus for the osteons and the interstitial lamellae in the longitude direction were 24.7 ± 2.5 GPa and 30.1 ± 2.4 GPa. As it’s difficult to distinguish osteons from interstitial lamellae in the transverse direction, the average elastic modulus for cortical bovine bone in the transverse direction was 19.8 ± 1.6 GPa. Significant differences were found in the modulus values between different microstructures of bone tissue and in different testing direction. It was found that the elastic modulus of bone bovine material in nano-level was higher than that in macro-level. The elastic modulus and
ultimate stress of large bone samples were 12.5 ± 1.9 GPa and 195 ± 19 MPa respectively from the compression test.

Novel nanocomposite fibres for technical textile applications : synthesis and characterisation of poly(m-xylene adipamide) montmorillonite nanocomposites

Technical textiles, based on advanced polymeric materials, are an important segment of the synthetic textile market. This area has seen considerable growth in recent times, now accounting for almost 25% of all manufactured synthetic fibres, and has driven the recent development of a range of specialist high performance polymer fibres that are stronger, lighter or have improved heat and fire resistance. However, the increasing size of the market has highlighted the need for materials that have improved performance whilst maintaining low manufacturing costs. These factors have resulted in a change in how new specialty fibres are developed and the emphasis in this field is now on the upgrading or improving of the properties of commodity (conventional) fibres by modifying their properties to suit specific applications.

This paper will describe our work on preparing novel polymer nanocomposite fibres by the addition of clay nanoparticles during melt extrusion. The effect of the nanoparticles on the processing of the fibres and the result on the physical morphology and mechanical properties will be described.

Lipid characterisation of different tissues and fillet portions of intensively farmed Murray Cod Maccullochella peelii peelii

Although many studies have focused on the lipid and fatty acids composition of farmed fish, no many have investigated their deposition pattern in different portions of the fillet. Previous studies, mainly on salmonids, have shown that lipids distribution varies greatly depending on the species, portion and type of muscle, but nevertheless, there is not accurate description of its deposition pattern in many fish, in particular in warm water, freshwater carnivorous species. Murray cod is the largest Australian native freshwater carnivorous fish and supports a small but well established and fast growing industry. The objective of this study was therefore to determine if there was any difference in lipid and fatty acid in different tissues such as muscle, liver and perivisceral fat and in different portions of the fillet of farmed Murray cod.

Three size fish (small, medium and large), all fed the same commercial diet, were selected from a commercial intensive farm. The left fillet of each fish was sectioned into nine portions, according to muscle lines and main anatomical features. The nine portions as well as whole right fillet, liver and perivisceral fat were analysed for proximate and fatty acid composition (Table 1).

Differences in lipid content were found amongst different portions of the fillet, with the dorsal/cranial portion (P1) recording the lowest and the more ventral/caudal portion (P8) recording the highest (P<0.05) value. The latter also recorded the highest amount of monounsaturated fatty acid (MUFA) and the lowest of polyunsaturated fatty acids (PUFA), arachidonic acid, 20:4n-6 (ArA), docosahexaenoic acid, 22:6n-3, (DHA) and n3/n6 ratio. In general, lipid content in the different fillet portions was inversely correlated to PUFA and directly to MUFA. Saturated fatty acid (SFA) and eicosapentaenoic acid, 20:5n-3 (EPA) did not show any discernible trend and were similar throughout, while significant differences of DHA and ArA content were observed. This study shows that lipid deposition in Murray cod varies remarkably and that different fatty acids are deposited at different rates. The results of this study show how different adjacent portions can be and therefore attention need to be paid when conducting chemical, nutritional and sensorial analyses on Murray cod.